磷酸活性炭自燃过程反应动力学研究

为研究磷酸活性炭的自燃危险性,以自制的磷酸活性炭(活化温度为300,500和700℃)为考察对象,利用同步热分析仪(STA)对活性炭氧化放热动力学进行试验研究。根据在2,5,10和20℃/min等4种不同升温速率下得到的活性炭DSC/TG曲线,结合Friedman-Reich-Levi动力学方法对反应过程中可能存在的反应机理进行初步判断。研究表明,随着活化温度的升高,活性炭的起始放热温度和最大放热温度随之升高;活性炭整个氧化反应过程中,活化能随着转化率的改变呈现一定规律性变化;碳氧化学反应和气体扩散共同影响活性炭氧化过程,且在不同阶段对氧化的贡献不同。     

二叔丁基过氧化物的热失控动力学研究

为研究二叔丁基过氧化物(DTBP)热失控危险性,利用C600微量量热仪对DTBP热分解动力学进行试验研究,测定DTBP在不同升温速率下的起始放热温度和分解热,分别用非等转化率法和等转化率法得到DTBP热分解反应的动力学参数。用非等转化率法确定反应的最佳反应级数为1,相应的活化能分别为137.75、132.60、128.61和122.93 kJ/mol,指前因子分别为8.82×1012、6.69×1012、2.06×1012和3.89×10111/s。用等转化率法确定的活化能范围为102～138 kJ/mol,并拟合出活化能与转化率的关系曲线。结合计算出的动力学参数,通过对DTBP分解机理的分析,可以推断其具有热失控危险性。     

连二亚硫酸钠热分解特性动力学及危险性评价

为了研究连二亚硫酸钠热分解动力学及热失控危险性,利用同步热分析法(TG-DSC)测定了不同升温速率下连二亚硫酸钠热分解特性。采用非等转化率法和等转化率法探究其动力学参数,分析其反应机理,推断连二亚硫酸钠热危险性。结果表明,连二亚硫酸钠分解方式有两种,反应活化能在140~240 kJ/mol。利用活化能比较、失控反应可能性、严重度评价及SADT等方法均发现,连二亚硫酸钠在生产、存储中存在危险性失控可能性。因此,要严格执行连二亚硫酸钠安全储运国家标准,避免事故发生。     

N-甲基羟胺盐酸盐的热分解机理的理论研究

为深入研究N-甲基羟胺盐酸盐(NMHH)热分解的反应特征,应用密度泛函理论,在w B97xd/6-311++g(2df,2pd)水平下,对NMHH的初步分解产物N-甲基羟胺(NMHA)及质子化的NMHA热分解反应中涉及的反应物、过渡态、中间体、产物的几何结构和能量情况进行了优化计算,提出了可能的热分解路径。结果表明,NMHA与质子化NMHA均存在两种热分解路径。NMHA在两条路径下分解需越过的能垒为250.75 k J/mol与428.64 k J/mol,而质子化NMHA在对应分解路径下需要越过的能垒分别为217.19 k J/mol与286.77k J/mol。在对应路径下质子化NMHA分解需越过的能垒明显低于NMHA的直接分解,并且随着反应的持续进行,质子化的NMHA的形成和分解将越来越容易发生。这表明NMHH的分解具有自催化特征,与试验结果吻合。     

等转化率法在硫化亚铁热动力学研究中的应用

FeS的氧化放热是引起石油储罐火灾与爆炸事故的主要原因.采用同步热分析仪对FeS的氧化倾向性及其热动力学规律进行研究,主要分析粒径为0.062～0.074mm的FeS在常温至900℃范围内的DSC/TG试验曲线,运用FWO、Kissinger、Friedman等多种等转化率法计算FeS的活化能和指前因子.其中FWO和Kissinger法的计算结果较为接近,可靠度较高.结合Malek法提出的y(α)-α标准曲线,推断出最概然机理函数为f(α)=(1-α)2.这说明FeS的氧化自燃反应符合二级普通化学反应机理.     

膨胀聚苯乙烯热分解动力学分析和寿命预测

针对既有聚苯乙烯泡沫类外墙外保温系统的防火问题,在空气和氮气气氛下对非阻燃和阻燃型膨胀聚苯乙烯泡沫进行了热重分析。样品由10℃/min、20℃/min、40℃/min和50℃/min四个升温速率从室温加热至800℃。热分解动力学参数由Flynn-Wall-Ozawa(FWO)等转化率方法和多参数非线性回归方法(multivariate non-linear re-gression method)计算,结果表明六溴环十二烷(HBCD)阻燃剂可一定程度上提高EPS的热稳定性。EPS在空气和氮气气氛下热解可认为是单步反应。非阻燃聚苯乙烯泡沫在空气和氮气气氛下的热解过程可由自催化n阶反应机理描述。阻燃EPS在空气气氛下的热解机理为自催化n阶反应,在氮气气氛下则为n阶反应机理。基于动力学参数和反应机理,对聚苯乙烯泡沫在不同温度下的寿命进行了预测。     

BIPB的热分解动力学和失控反应模拟

为了评估双(叔丁过氧基)二异丙苯(BIPB)的热危害,对其热分解过程进行多速率的动态扫描C80热分析,用几种简单的热危害评估方法分析其热危害。然后应用模式法、无模式法(Friedman微分等转化率法)分别对试验结果进行处理,得到分解动力学数据,并用ASTM E 698法得到活化能数据,同时用C80、ARC和DSC的试验数据验证分解动力学数据的可靠性。最后利用无模式法的分解动力学数据进行BIPB绝热条件下和非绝热的2m3球形容器中的失控反应模拟,得到类似工艺条件下BIPB的安全控制温度。     

Mg(BH_4)_2和MgH_2对RDX热分解特性的影响

在黑索今(RDX)中加入具有高热值的金属氢化物(Mg(BH4)2和MgH2)有望提高RDX的爆炸性能,但同时给RDX的安全使用带来挑战。为了探索RDX与这2种金属氢化物的相容性与安定性,采用差示扫描量热法(DSC)研究Mg(BH4)2和MgH2对RDX热分解性能的影响,并由DSC得到的数据计算动力学参数,参照GJB770B—2005的方法分析这2种金属氢化物与RDX的相容性和安定性。结果表明,加入Mg(BH4)2使RDX的表观活化能从159.22 kJ/mol增加至180.27 kJ/mol,加入MgH2使RDX的表观活化能降低至133.69 kJ/mol;Mg(BH4)2与RDX的相容性为1级,MgH2与RDX的相容性为3级,加入Mg(BH4)2使RDX的安定性有所提高,加入MgH2降低了RDX的安定性。因此,在将MgH2作为RDX的高能添加剂以前,必须首先提高其与RDX的相容性以保证试验和存储过程的安全。     

番龙眼木的热分解失重及动力学研究

木材热解是木材类火灾事件的先导过程,是引起后续的阴燃、着火、燃烧和火焰蔓延等各种现象的重要因素,因此研究木材的热解非常重要。采用热重分析法对番龙眼木的热重特性及反应动力学进行研究。在空气气氛下,研究样品粒径、试验气氛和升温速率对番龙眼木热解特性的影响。对番龙眼木的热解反应过程的分析,采用Flynn-Wall-Ozawa积分法、Kissinger最大速率法和atava-esták积分法对动力学进行处理。试验得到了一些热解动力学的参数,并推断出不同温升速率下番龙眼木的动力学最概然机理方程为反应级数函数,n=4     

过氧化二异丙苯的热稳定性研究

用TG-DTG-DTA(热重-微分热重-差热)联用技术研究了过氧化二异丙苯在动态氮气气氛中的热分解过程.过氧化二异丙苯DTA曲线呈现一个吸热熔化峰和一个放热分解峰.在不同升温速率的TG曲线上,过氧化二异丙苯失重开始温度大致相同.采用无模式方法的Flynn-Wall-Ozawa(FWO)法和Starink法对热分解的数据进行非等温动力学分析处理,求出了热分解反应的表观活化能.Flynn-Wall-Ozawa(FWO)法计算得的活化能的值为112.39 kJ/mol,Starink法计算得的活化能的值为111.23 kJ/mol.     

Study on decomposition of hydroxylamine/water solution

The risk evaluation of decomposition of hydroxylamine(HA)/water solution was studied experimentally. The thermal property of HA/water solution was studied from the calorimetric data obtained using the differential thermal analysis (DTA). The intensity of decomposition was studied on the basis of the results of the mini closed pressure vessel test (MCPVT) and the pressure vessel test (PVT) in addition to the steel tube test.The thermal property of HA/water solution was evaluated on the basis of results of the DTA. The heat-release onset temperatures using the no-treated stainless steel cells were more than 70 K below those measured using the GSC. This result implies that the heat-release onset temperature depends on the materials of sample cell. On the other hand, the heat of reaction did not depend on the materials of sample cell.The intensity of the thermal decomposition was investigated on the basis of results of the MCPVT, the PVT and the steel tube test. The intensity of the thermal decomposition increased as the HA concentration increased in the MCPVT. The intensity of the thermal decomposition increased greatly when the HA concentration was beyond 80wt.% in the MCPVT. It was elucidated that the thermal decomposition of HA 70wt.%/water solutions was very violent in the PVT. In addition, HA/water solutions of more than 80wt.% concentration could detonate in the steel tube test. HA 80 wt.% water/solution was easily detonated by a detonator without RDX in the steel tube test.In addition, the decomposition hazard of HA/water solution by the metal ion and the iron powder was studied in this paper. The thermal stability of HA85%/water solution with the iron ion or the iron powder was discussed on the basis of the heat-release onset temperature by the DTA. The heat-release onset temperatures decreased when the concentration of the iron ion or the iron powder increased in the DTA measurements. The reactiveness of HA/water solution with the metal ion of iron, manganese, nickel, chromium and copper was examined by measuring the mass loss of HA/water solution after the metal ion was added to HA/water solution at room temperature. The reactiveness of HA/water solution with the iron powder was also studied in this paper. The ferrous ion, the ferric ion and the iron powder reacted with HA/water solution. Ignition automatically began when the 0.2wt.% ferric ion solution was added to HA85wt.%/water solution. The mass loss rate depended on the HA concentration greater than the iron ion concentration. The mass loss rate increased when an amount of the iron powder increased. On the other hand, the decomposition reaction of HA85wt.%/water solution with Cu²⁺ was calm compared to that of the iron ion. HA/water solution did not react with Mn²⁺, Ni²⁺ and Cr³⁺ at room temperature.     

Thermal decomposition mechanism of 65% lysine sulfate powder and its thermal stability based on thermal analysis

Lysine is widely used in the fields of food, medicine and feed, which generally appears in the form of lysine sulfate or lysine hydrochloride dust because of the high instability of the free L-lysine. The L-lysine Sulfate is in high risk of decomposition, spontaneous ignition and even the dust explosion, because the control temperature in its production process is high up to 90 °C. Thus, the thermal behaviors and its thermal stability of 65% lysine sulfate are experimentally explored in Air and Nitrogen using the simultaneous TG-DSC measurements. Results show: (1) the decomposition of 65% lysine sulfate can be divided into three stages both in the atmospheres of air and nitrogen, and most of the weight loss occurred in the first two stages, which are related with the decarboxylation and deamination process. (2) The effects of atmosphere on the decomposition of 65% lysine sulfate mainly occur at the third stage. In this stage, the weight loss in nitrogen is only 14.2%, which is much lower than that in air (34.3%), which is related to the oxidative degradation at high temperature. Besides, the active energy is slightly increased in nitrogen compared to that in air. (3) The initial temperatures of the decomposition of the 65% lysine sulfate are 145 °C and 155 °C, for the air and nitrogen atmosphere, respectively, which are much lower than that (260 °C) of the pure lysine.     

环氧乙烷热稳定性及杂质对其影响研究

为研究环氧乙烷热稳定性及杂质对其影响,利用C600微量量热仪对环氧乙烷进行热分解试验研究,获得了环氧乙烷分解活化能和绝热条件下到达最大反应速率所需时间(TMRad)等动力学参数.研究了氢氧化钾固体、45％氢氧化钾溶液、三氧化二铁和六水三氯化铁对环氧乙烷热分解特性的影响.结果表明:随温升速率的增加,环氧乙烷热分解起始放热温度逐渐增大;分解活化能E在55～ 90 kJ/mol;环氧乙烷在常温下不易发生热失控;但氢氧化钾固体、45％氢氧化钾溶液、三氧化二铁和六水三氯化铁均对环氧乙烷的热分解有一定程度的影响,使其起始放热温度和最大放热温度都有不同程度的降低,且氢氧化钾溶液和氢氧化钾固体的影响最为明显.     

Use of isoperibolic calorimetry for the study of the effect of water concentration,temperature and reactor venting on the rate of hydroxylamine thermal decomposition

Hydroxylamine, NH₂OH, thermal decomposition has been responsible for two serious accidents. However, its reactive behavior and the synergy of factors affecting the rate of its decomposition are not understood. In this work, isoperibolic calorimetric measurements were performed in a metal reactor, in the temperature range 130–150 °C, employing 30–80 ml solutions containing 1.4–20 g of pure hydroxylamine (2.8–40 g of the supplied reagent). The calorimetric measurements were performed in order to assess the effects that NH₂OH concentration, temperature and reactor venting has on NH₂OH rate of decomposition. The measurements showed that increased concentration or temperature, results in faster reactions and probably higher pressure generation per mass of reactant, with concentration having a more pronounced effect. However, when both factors work synergistically the result is dramatically worse in terms of reaction rate. The pressure generation is also different, thus indicating that different reaction pathways predominate each time. Venting the produced gases in stages resulted in the highest mass loss of the solution.     

Ammonium nitrate thermal decomposition with additives

Runaway reactions present a potentially serious threat to the chemical process industry and the community; such reactions occur time and time again often with devastating consequences. The main objective of this research is to study the root causes associated with ammonium nitrate (AN) explosions during storage. The research focuses on AN fertilizers and studies the effects of different types of fertilizer compatible additives on AN thermal decomposition. Reactive Systems Screening Tool (RSST) has been used for reactivity evaluation and to better understand the mechanisms that result in explosion hazards. The results obtained from this tool have been reported in terms of parameters such as “onset” temperature, rate of temperature and pressure rise and maximum temperature. The runaway behavior of AN has been studied as a solid and solution in water. The effect of additives such as sodium sulfate (Na₂SO₄) and potassium chloride (KCl) has also been studied. Multiple tests have been conducted to determine the characteristics of AN decomposition accurately. The results show that the presence of sodium sulfate can increase the “onset” temperature of AN decomposition thus acting as AN thermal decomposition inhibitor, while potassium chloride tends to decrease the “onset” temperature thus acting as AN thermal decomposition promoter.     

基于详细化学动力学的甲烷热着火影响因素分析

利用化学动力学软件CHEMKIN4.1,在不同初始温度、浓度、湿度和压强下,对甲烷热着火进行了详细化学动力学 模拟。通过对主要组分摩尔浓度分析和温度敏感性分析,得到了甲烷热着火过程的主要基元反应和引发热着火发生的主 要原因。通过对甲烷热着火的延迟时间、热着火发生后主要生成物摩尔浓度和反应后的温度的对比分析,揭示了初始浓 度、湿度和压强对甲烷热着火的影响规律。本研究可以为甲烷为主的气体如瓦斯、天然气等可燃气体的燃烧和爆炸提供 理论支撑,从而有效利用这些可燃气体,降低灾害的发生。