超声波降解四环素类抗生素废水

采用超声波降解模拟废水中四环素类抗生素(TCs):土霉素(OTC)、四环素(TC)和金霉素(CTC),考查废水初始浓度、初始pH、超声波输入功率密度、曝气量和自由基清除剂(正丁醇)对降解效率的影响。结果表明,超声波可以快速高效地降解废水中的TCs,CTC最易被降解,TC和OTC次之;在OTC、TC和CTC初始浓度0.25 mg/L,初始pH=8.2,声功率密度1.2 W/mL,气水体积比30∶1的条件下,超声波辐照20 min后去除率分别达到76.8%、84.0%和94.4%。在实验研究条件下,TCs去除率均随初始浓度(0.25~2.00 mg/L)的增大而降低,但总去除浓度升高;碱性条件有利于TCs降解,去除率随初始pH(6~11)升高而升高;功率密度(0.24~1.96 W/mL)越高,TCs去除率也越高;曝气后TCs的去除率明显升高,随着气水比(10∶1~60∶1)的增大,去除率逐渐上升;正丁醇有效抑制TCs超声波降解,可推断TCs主要降解途径为自由基氧化。TCs超声波降解过程符合伪一级动力学反应特征。     

Degradation of tetracycline at a boron-doped diamond anode: influence of initial pH,applied current intensity and electrolyte

The anodic oxidation of tetracycline was performed in an up-flow reactor, operating in batch mode with recirculation, using as anode a boron-doped diamond electrode. The influence on the degradation rate of solution initial pH (2 to 12), applied current intensity (25 to 300 A m^?2) and type of electrolyte (sodium sulphate or sodium chloride) were investigated. For the assays run at equal current density, with sodium sulphate as electrolyte, the solution’s initial pH of 2 presented the highest absorbance and chemical oxygen demand removals. Regarding the influence of current density, for equal charge passed, the organic load removal rate decreased with the increase in applied current. When sodium sulphate was used as an electrolyte, high-performance liquid chromatography (HPLC) results have shown an almost complete removal of tetracycline after a 2-h assay. HPLC results have also shown the presence of oxamic acid as one of the intermediates of tetracycline anodic oxidation. The complete removal of tetracycline was much faster in the presence of chloride ions that promoted the complete degradation of this antibiotic in 30 min. However, in the presence of chloride ions, the tetracycline mineralization is slower, as observed by the lower organic carbon removal rate when compared to that of the tetracycline degradation in the presence of sulphate.     

高铁酸钾降解苯胺废水的机制研究

研究了高铁酸钾投加量、初始pH及苯胺初始浓度对苯胺降解效果的影响.结果表明.苯胺废水的COD去除事随高铁酸钾投加量和苯胺初始浓度的增大而升高,而初始pH对COD去除率影响不明显.对高铁酸钾降解苯胺废水后的产物进行了气相色谱/质谱(GCIMS)分析.在此基础上详细探讨了高铁酸钾降解苯胺的机制.     

O3/H2O2法去除浮选药剂丁基黄药

采用O3/H2O2法去除水中丁基黄药,考察了H2O2/O3摩尔比、pH值、丁基黄药初始浓度、温度和自由基抑制剂对丁基黄药的去除效果的影响。结果表明,在相同O3投加量下,H2O2量越大,丁基黄药去除率越高。pH值为7～9,温度在293～303 K的范围内,O3/H2O2对丁基黄药都有很高的去除率。碳酸氢根和叔丁醇能在一定程度上降低丁基黄药的降解效率。研究还发现,在O3和H2O2投加量相同的条件下,H2O2多次投加对水中丁基黄药的处理效果明显优于一次性投加。GC/MS分析表明,O3/H2O2氧化丁基黄药氧化产物为羧酸类物质。     

O3/H2O2法去除浮选药剂丁基黄药

采用O3/H2O2法去除水中丁基黄药,考察了H2O2/O3摩尔比、pH值、丁基黄药初始浓度、温度和自由基抑制剂对丁基黄药的去除效果的影响。结果表明,在相同O3投加量下,H2O2量越大,丁基黄药去除率越高。pH值为7～9,温度在293～303 K的范围内,O3/H2O2对丁基黄药都有很高的去除率。碳酸氢根和叔丁醇能在一定程度上降低丁基黄药的降解效率。研究还发现,在O3和H2O2投加量相同的条件下,H2O2多次投加对水中丁基黄药的处理效果明显优于一次性投加。GC/MS分析表明,O3/H2O2氧化丁基黄药氧化产物为羧酸类物质。     

钯修饰碳纳米管电极电催化氧化三氯生

采用钯修饰多壁碳纳米管(MWCNTs)电极电催化氧化降解三氯生,考察了极板间距、电流密度、离子强度、pH、初始浓度和电解时间对三氯生去除效率的影响,并探讨了其反应动力学。结果表明:钯修饰多壁碳纳米管(MWCNTs)电极电催化氧化降解三氯生的最佳条件为:三氯生初始浓度为50 mg/L,电流密度约为10 mA/cm2,极板间距为1 cm,pH为11,电解质Na2SO4浓度为1 000 mg/L。此条件下,反应时间为3 h时三氯生的去除率可达到99%以上,三氯生的降解为零级反应。     

Factorial design analysis for COD removal from landfill leachate by photoassisted Fered-Fenton process

The Fered-Fenton process has been shown to be an effective method for leachate treatment, but it still faces problems of inadequate regeneration of ferrous ion. However, the use of the photoassisted Fered-Fenton process could overcome this difficulty and improve the efficiency of chemical oxygen demand (COD) removal since photoassisted Fered-Fenton process induces the production of hydroxyl radicals from the regeneration of ferrous ions and the reaction of hydrogen peroxide with UV light. As there are so many operating parameters in photoassisted Fered-Fenton process, it is necessary to develop a mathematical model in order to produce the most economical process. In the present study, a factorial design was carried out to evaluate leachate treatment by photoassisted Fered-Fenton process. The influence of the following variables: H₂O₂ concentration, Fe²⁺ concentration, current density, and initial pH in the photoassisted Fered-Fenton process was investigated by measuring COD removal efficiencies after 60-min reaction. The relationship between COD removal and the most significant independent variables was established by means of an experimental design. The H₂O₂ concentration, Fe²⁺ concentration, initial pH, and the interaction effect between current density and initial pH were all significant factors. The factorial design models were derived based on the COD removal efficiency results and the models fit the data well.     

Solar TiO2-assisted photocatalytic degradation of IGCC power station effluents using a Fresnel lens

The heterogeneous TiO2 assisted photocatalytic degradation of wastewater from a thermoelectric power station under concentrated solar light irradiation using a Fresnel lens has been studied. The efficiency of photocatalytic degradation was determined from the analysis of cyanide and formate removal. Firstly, the influence of the initial concentration of H2O2 and TiO2 on the degradation kinetics of cyanides and formates was studied based on a factorial experimental design. Experimental kinetic constants were fitted using neural networks. Results showed that the photocatalytic process was effective for cyanides destruction (mainly following a molecular mechanism), whereas most of formates (degraded mainly via a radical path) remained unaffected. Finally, to improve formates degradation, the effect of lowering pH on their degradation rate was evaluated after complete cyanide destruction. The photooxidation efficiency of formates reaches a maximum at pH around 5-6. Above pH 6, formate anion is subjected to electrostatic repulsion with the negative surface of TiO2. At pH<4.5, formate adsorption and photon absorption are reduced due to some catalyst agglomeration.     

Aqueous photolysis of tetracycline and toxicity of photolytic products to luminescent bacteria

The extensive utilization of antibiotics in the pharmaceutical therapies and agricultural husbandry has led to the worldwide pollution in environments. In this study the photolysis behaviors of tetracycline (TC) and toxicity of its degradation products were investigated. The results showed that TC photolysis followed first-order kinetics. The photolysis rate was found to be dependent on the initial TC concentration and increasing TC concentration from 10 to 40mgl(-1) led to the decrease of the photolysis rate constant from 0.0045min(-1) to 0.0014min(-1). TC photolysis was highly pH-dependent and strongly enhanced at high pH value. Markedly elevated TC photolysis was also observed in the presence of nitrate and dissolved organic matter. Upon irradiation for 300min, only 15% reduction of total organic carbon (TOC) occurred in spite of quick conversion of 73% of TC, suggesting that a majority of TC transformed into intermediate products without complete mineralization. The intermediate products from TC photolysis were analyzed using high-performance liquid chromatography-electrospray ionisation-mass spectrometry (HPLC-ESI-MS) and the main photolysis products of TC were proposed. The toxicity of the photolysis compounds was evaluated using luminescent bacterium, and the results revealed that the toxicity increased with irradiation, indicative of a higher adversity risk of the degradation products of TC on bacteria upon photolysis.     

TiO2/Ti转盘液膜反应器光电催化处理罗丹明B

采用溶胶-凝胶法制备了TiO2/Ti电极,X射线衍射(XRD)分析表明,TiO2主要为锐钛矿,晶粒尺寸约为46 nm.以TiO2/Ti电极作阳极,Cu电极作阴极,组装成转盘液膜反应器,考察了其光电催化处理染料罗丹明B(RhB)的影响因素(转盘转速、偏压、溶液初始pH、RhB初始浓度和电解质浓度).得到最佳处理条件为:转盘转速90 r/min,偏压0.4V,溶液初始pH2.5,电解质(硫酸钠)质量浓度0.5 g/L.在最佳处理条件下,处理20 mg/L RhB染料废水90 min的脱色率和总有机碳(TOC)去除率分别达到97.2％和72.7％.结果表明,由于同时强化了激发光源的利用率和溶液的传质效率,TiO2/Ti转盘液膜反应器可高效光电催化处理染料废水.     

Fe (III) supported on resin as effective catalyst for the heterogeneous oxidation of phenol in aqueous solution

FeIII supported on resin as an effective catalyst for oxidation was prepared and applied for the degradation of aqueous phenol. Phenol was selected as a model pollutant and the catalytic oxidation was carried out in a batch reactor using hydrogen peroxide as the oxidant. The influent factors on oxidation, such as catalyst dosage, H2O2 concentration, pH, and phenol concentration were examined by considering both phenol conversion and chemical oxygen demand (COD) removal. The FeIII-resin catalyst possesses a high oxidation activity for phenol degradation in aqueous solution. The experimental results of this study show that almost 100% phenol conversion and over 80% COD removal can be achieved with the FeIII-resin catalyst catalytic oxidation system. A series of prepared resin were investigated for improving the oxidation efficiency. It was found that the reaction temperature and initial pH in solution significantly affected both of phenol conversion and COD removal efficiency. The activity of the catalyst significantly decreased at high pH, which was similar to the Fenton-like reaction mechanism. Results in this study indicate that the FeIII-resin catalytic oxidation process is an efficient method for the treatment of phenolic wastewater.     

微波-Fenton对沼液中抗生素和激素的高级氧化

采用微波强化Fenton氧化处理系统,研究H2O2浓度、Fe2+浓度、初始pH、微波辐射时间和微波辐射功率对沼液中喹乙醇、土霉素、四环素及金霉素降解效果的影响.结果发现,采用微波强化Fenton氧化降解沼液中抗生素与激素的最优条件是:H2O2浓度为40 mg/L、Fe2+浓度为12 mg/L、初始pH为4、微波辐射时间为2 min、微波辐射功率为中火(445W),沼液中喹乙醇、土霉素、四环素、金霉素和COD的去除率分别达到67％、93％、91％、88％和46％.在水浴条件下,与单独微波辐射和单独Fenton相比,微波强化Fenton氧化有明显的优越性.     

紫外光协助高锰酸钾降解四环素的研究

高锰酸钾氧化法在实际水处理中得到了一定的应用,但对有机污染物的去除和降解能力相对有限,为此提出了以外加紫外光照射协助高锰酸钾氧化的方法。以四环素作为模型污染物,考察了四环素浓度、高锰酸钾浓度、反应时间、初始pH条件和不同紫外光照射等的影响。结果表明,高锰酸钾能够氧化并去除四环素,紫外光照射明显提高了高锰酸钾对四环素的降解效果,并且254 nm紫外光照射对降解的促进作用远大于365 nm紫外光。在所考察的pH范围内,无论紫外光照射与否,高锰酸钾在酸性条件下的降解效率最高,中性条件较高,碱性条件次之。     

催化臭氧氧化染料溶液的研究

采用催化臭氧化技术降解染料废水,以甲基紫溶液为目标污染物,研究了过渡型金属离子的类型,Fe2+的浓度,溶液初始pH值,染料浓度和正丁醇等因素对其降解率的影响。实验结果表明:臭氧氧化甲基紫溶液的过程中,加入一定浓度的过渡型金属离子对甲基紫的去除具有促进作用;当臭氧浓度为16 mg/L,一定浓度范围内,Fe2+催化臭氧化的效果随着浓度的增加而增加,但Fe2+浓度为13 mg/L时,甲基紫的降解率下降;在酸性范围时,pH值增大其降解率会减小;染料浓度增加,甲基紫的降解率减小,但是其绝对降解值会增加;正丁醇的加入抑制氧化反应的进行,甲基紫的降解率下降,说明催化臭氧化过程中有羟基自由基产生。染料降解过程符合一级反应动力学规律。     

Application of Klebsiella oxytoca immobilized cells on the treatment of cyanide wastewater

Klebsiella oxytoca, isolated from cyanide-containing industrial wastewater, has been shown to be able to biodegrade cyanide to non-toxic end products. The technology of immobilized cells can be applied in biological treatment to enhance the efficiency and effectiveness of biodegradation. In this study, potassium cyanide was used as the target compound and both alginate and cellulose triacetate techniques were applied for the preparation of immobilized cells. Results from this study show that KCN can be utilized as the sole nitrogen source by K. oxytoca. The free suspension systems reveal that the cell viability was highly affected by initial KCN concentration and pH. Results show that immobilized cell systems could tolerate a higher level of KCN concentration and wider ranges of pH. In the batch experiments, the maximum KCN removal efficiencies using alginate and cellulose triacetate immobilized beads were 0.108 and 0.101mM h(-1) at pH 7, respectively. Results also indicate that immobilized system can support a higher biomass concentration. Complete KCN degradation was observed after the operation of four consecutive degradation experiments with the same batch of immobilized cells. This suggests that the activity of immobilized cells can be maintained and KCN can be used as the nitrogen source throughout KCN degradation experiments. The maximum KCN removal rates using alginate and cellulose triacetate immobilized beads in continuous-column system were 0.224 and 0.192mMh(-1) with initial KCN concentration of 3mM, respectively. Results indicate that the immobilized cells of K. oxytoca would be applicable to the treatment of cyanide-containing wastewaters.     

Evaluation of the efficiency of monopolar and bipolar BDD electrodes for electrochemical oxidation of anthraquinone textile synthetic effluent for reuse

The efficiency of the electrochemical degradation of synthetic wastewater containing an anthraquinone dye has been comparatively studied in two electrolytic cells with a synthetic boron-doped diamond (Si/BDD) as an anode. The first is an individual cell (Cell 1) with monopolar electrode BDD and the second (Cell 2) has two bipolar electrodes BDD self-polarized. The bulk electrolysis was performed at the same initial operating conditions in order to quantify the influence of the initial pH and current density on dye discoloration and global mineralization removal. The current efficiency and the consumption energy were also evaluated. When the same solutions have been comparatively treated with the two cells, a quite good mineralization is found in Cell 2. This result supposed more fraction of the applied current is used for the electrocombustion reaction on Cell 2 if compared to Cell 1 and small amount rest for the side reaction of oxygen evolution. The HPLC analyses confirmed this hypothesis and showed that the concentration trend of intermediates (sulfanilic acid, phthalate acid and salicylic acid) with electrolysis time was different on two cells. Phototoxicity tests show that the electrochemical oxidation with BDD electrodes could be useful as a pretreatment technique for reducing hazardous wastewater toxicity.     

Fenton-like degradation of nalidixic acid with Fe3+/H2O2

The Fenton-like degradation of nalidixic acid was studied in this work. The effects of Fe³⁺ concentration and initial H₂O₂ concentration were investigated. Increasing the initial H₂O₂ concentration enhances the degradation and mineralization efficiency for nalidixic acid, while Fe³⁺ shows an optimal concentration of 0.25 mM. A complete removal of nalidixic acid and a TOC removal of 28 % were achieved in 60 min under a reaction condition of [Fe³⁺]?=?0.25 mM, [H₂O₂]?=?10 mM, T?=?35 °C, and pH?=?3. LC–MS analysis technique was used to analyze the possible degradation intermediates. The degradation pathways of nalidixic acid were proposed according to the identified intermediates and the electron density distribution of nalidixic acid. The Fenton-like degradation reaction of nalidixic acid mainly begins with the electrophilic attack of hydroxyl radical towards the C₃ position which results in the ring-opening reaction; meanwhile, hydroxyl radical attacking to the branched alkyl groups of nalidixic acid leads to the oxidation at the branched alkyl groups.     

O3/H2O2工艺降解1,2,4-三氯苯的优化设计

考察用不同的氧化剂降解1,2,4-三氯苯（TCB）,3种不同方法对TCB的去除效果存在较大差别,其处理效果依次为：H2O2〈O3〈O3/H2O2。采用响应面法优化O3/H2O2工艺降解TCB的条件。结果表明,TCB初始浓度和H2O2投加量对TCB去除效果影响较大。TCB的降解符合准一级反应动力学规律,最佳降解条件为TCB初始浓度0.3 mg/L,pH=8.13,H2O2投加量0.40 mmol/L,O3转化率75%。在此条件下,TCB的平均去除率为91.5%,与预测值93.1%吻合度较高。     

Pressurized CO2/zero valent iron system for nitrate removal

A fluidized zero valent iron (ZVI) reactor pressurized by CO(2) gas for controlling pH was employed for nitrate reduction. The proposed CO(2) pressurized system potentially has advantages of using less CO(2) gas and reaching equilibrium pH faster than CO(2)-bubbled system. However, due to weak acid nature of carbonic acid, system pH gradually increased with increasing oxidation of ZVI and reduction of nitrate. As pH increased with progress of reaction, nitrate removal rate decreased continuously. The results indicate that nitrate removal efficiency increases with increasing initial ZVI dosage but reaches plateau at ZVI doses of higher than 8.25gl(-1), and initial nitrate concentration up to 100mg l(-1) as N has minimal impact on the removal efficiency. Unlike the fluidized system with pH control by strong acid reported in our pervious study, near 100% of nitrogen recovery was observed in the current process, indicating that nitrate reduction by ZVI with different pH controlled mechanisms will have different reaction routes.     

Adsorption and precipitation of tetracycline with struvite.

The interaction of tetracycline with struvite during adsorption and precipitation processes was investigated. Tetracycline removal by adsorption was affected by solution pH, contact time, and struvite concentration. The lowest tetracycline removal (8.4%) was observed at pH 7.7, the dissociation constant (pKa2) of tetracycline. Because of the electrostatic repulsion, the amount of tetracycline adsorbed on the surface was low. The small amount of adsorption was the result of surface complexation between tetracycline ions and metal ions. Calcium (Ca2+) ions in the adsorbent enhanced the binding of tetracycline. Freundlich (KF: 0.04, n: 1.49) and Redlich-Peterson (KR: 0.08, alphaR: 0.98, betaR: 0.49) models best defined the equilibrium data. In the case of struvite precipitation, approximately 22% of tetracycline was removed as a result of binding to struvite alongside struvite formation.