Dioxin production during the thermal treatment of meat and bone meal residues

Safe animal by-product disposal is a priority target as a result of the Bovine Spongiform Encephalopathy crisis in the European beef industry. One such disposal option is the incineration of by-product material such as meat and bone meal residues (MBM) for the purpose of energy recovery. Although currently applied, the thermal decomposition of MBM wastes has not been scientifically studied until now. A series of experiments has been performed to study the thermal behavior of MBM both in inert (N2) and reactive atmosphere (air), both by thermogravimetry and in a horizontal laboratory furnace. As a general trend, MBM gives low PCDD/F values, compared with incineration of other wastes. Maximum yield of pollutants is observed at a nominal temperature between 700 and 800 degrees C.     

Effects of biodiesel made from swine and chicken fat residues on carbon monoxide,carbon dioxide,and nitrogen oxide emissions

The effects of two alternative sources of animal fat-derived biodiesel feedstock on CO₂, CO, NO_x tailpipe emissions as well as fuel consumption were investigated. Biodiesel blends were produced from chicken and swine fat waste (FW-1) or floating fat (FW-2) collected from slaughterhouse wastewater treatment processes. Tests were conducted in an unmodified stationary diesel engine operating under idling conditions in attempt to simulate slow traffic in urban areas. Significant reductions in CO (up to 47% for B100; FW-2) and NO_x (up to 20% for B5; FW-2 or B100; FW-1) were attained when using biodiesel fuels at the expense of 5% increase in fuel consumption. Principal component analysis (PCA) was performed to elucidate possible associations among gas (CO₂, CO, and NO_x) emissions, cetane number and iodine index with different sources of feedstock typically employed in the biodiesel industry. NO_x, cetane number and iodine index were inversely proportional to CO₂ and biodiesel concentration. High NO_x emissions were reported from high iodine index biodiesel derived especially from forestry, fishery and some agriculture feedstocks, while the biodiesel derived from animal sources consistently presented lower iodine index mitigating NO_x emissions. The obtained results point out the applicability of biodiesel fuels derived from fat-rich residues originated from animal production on mitigation of greenhouse gas emissions. The information may encourage practitioners from biodiesel industry whilst contributing towards development of sustainable animal production.

Implications: Emissions from motor vehicles can contribute considerably to the levels of greenhouse gases in the atmosphere. The use of biodiesel to replace or augment diesel can not only decrease our dependency on fossil fuels but also help decrease air pollution. Thus, different sources of feedstocks are constantly being explored for affordable biodiesel production. However, the amount of carbon monoxide (CO), carbon dioxide (CO₂), and/or nitrogen oxide (NO_x) emissions can vary largely depending on type of feedstock used to produce biodiesel. In this work, the authors demonstrated animal fat feasibility in replacing petrodiesel with less impact regarding greenhouse gas emissions than other sources.     

生物柴油促进原油污染砂粒释放油

对4种生物柴油促进原油污染砂粒释放油的效果进行了研究,并探讨了菜籽生物柴油投加量和砂粒粒径对促进效果的影响。结果表明,菜籽生物柴油的促进效果最好,8 h释放量达到73%,废油脂生物柴油的效果最差,仅为52%;生物柴油的促进效果随着投加量的增大而升高,当投加量超过海水体积的5%时促进效果不再明显增加;在生物柴油作用下,小粒径砂粒上原油的释放效果优于大粒径砂粒。     

Soil-mediated prion transmission: is local soil-type a key determinant of prion disease incidence?

Prion diseases, including chronic wasting disease (CWD) and scrapie, can be transmitted via indirect environmental routes. Animals habitually ingest soil, and results from laboratory experiments demonstrate prions can bind to a wide range of soils and soil minerals, retain the ability to replicate, and remain infectious, indicating soil could serve as a reservoir for natural prion transmission and a potential prion exposure route for humans. Preliminary epidemiological modeling suggests soil texture may influence the incidence of prion disease. These results are supported by experimental work demonstrating variance in prion interactions with soil, including variance in prion soil adsorption and soil-bound prion replication with respect to soil type. Thus, local soil type may be a key determinant of prion incidence. Further experimental and epidemiological work is required to fully elucidate the dynamics of soil-mediated prion transmission, an effort that should lead to effective disease management and mitigation strategies.     

Aquatic Resource Conservation. The first Yangtze finless porpoise successfully born in captivity (4 pp)

Background As the sole freshwater subspecies of finless porpoise (Neophocaena phocaenoides), the Yangtze finless porpoise (N. p. asiaeorientalis) lives only in the middle and lower reaches of the Yangtze River and its appended Poyang and Dongting Lakes. As a result of human activity on the river, including over and illegal fishing, pollution, transportation and dam construction, the population of Yangtze finless porpoises has been steadily and rapidly decreasing during the past several decades, which leads the animal to be endangered. Methods For saving this unique animal from extinction, three corresponding measures, in situ conservation, ex situ conservation, and intensifying breeding research in captivity, were proposed and have been implemented since the 1980s. Results After successfully rearing the animals in captivity for almost nine years, the first Yangtze finless porpoise was successfully born in captivity on July 5, 2005. The calf is male, with a body length of 69cm. This is the first freshwater cetacean ever born in captivity. Conclusion The successful birth of this calf confirms that it is possible to breed the Yangtze finless porpoise in captivity. Furthermore, this will greatly benefit the conservation efforts, and also greatly bolster our on-going efforts to study the reproductivebiology of these animals. Recommendation More studies and efforts are expected to establish a sustainable, captive colony of the Yangtze finless porpoise, which will not only greatly expand our knowledge about the reproduction biology of this animal, but also help to redeem the wild population through a careful yearly 'soft releasing' process.     

Polychlorinated biphenyl (PCB) congeners and chlorinated pesticides in a cod liver oil reference material

A cod liver oil reference material, Standard Reference Material (SRM) 1588, which was issued by the National Institute of Standards and Technology (NIST) in 1989, has certified concentrations for five polychlorinated biphenyl (PCB) congeners and ten chlorinated pesticides. Recently, this SRM has been extensively characterized by additional analyses at NIST and by analyses at the Canadian Wildlife Service (CWS) where the SRM was used as a control sample during routine analyses of wildlife tissue specimens. In this paper the results from NIST and CWS are compared and the concentrations for over 40 PCB congeners and 20 chlorinated hydrocarbons are reported.     

Exposure of ruminants to persistent organic pollutants and potential of decontamination

Human activities are emitting persistent organic pollutants (POPs) to the environment. These compounds have raised concerns about the risk of transfer through the food chain via animal products. They are characterized by a strong persistence in environmental matrices and a lipophilicity which may lead to their accumulation in fat tissues. In EU Regulations (no. 1881/2006, 1259/2011), maximum acceptable levels for polychlorinated dibenzo-p-dioxins, polychlorinated dibenzofurans (PCDD/Fs), and dioxin-like or nondioxin-like polychlorinated biphenyls (PCBs) in food of animal origin have been set. Transfer rates from contaminated fodder to milk have been established: for PCBs, the rate of transfer varies from 5 to 90 % and for PCDD/Fs from 1 to 40 %. The differential transfer of the compounds towards milk is related to the hydrophobicity of the pollutants and to their metabolic susceptibility. According to numerous authors, soil is the major reservoir for POPs, and its involuntary ingestion by farm animals reared outdoors may be the main cause of animal product contamination (meat, milk, or eggs). Recent studies seem to indicate that soil is a real risk matrix in terms of transfer of pollutants to the food chain. A POP crisis management is extremely difficult, since it impacts many farmers located in the contaminated area. The question arising is to know if livestock contaminated by POPs may be decontaminated and further used for their initial purpose. Recent data demonstrate that the decontamination process appear feasible and depends on initial level of contamination or the physiological status of the animals.     

Transcriptional responses of heat shock protein 70 (Hsp70) to thermal, bisphenol A, and copper stresses in the dinoflagellate Prorocentrum minimum

The designation of biodiesel as an environmental-friendly alternative to diesel oil has improved its commercialization and use. However, most biodiesel environmental safety studies refer to air pollution and so far there have been very few literature data about its impacts upon other biotic systems, e.g. water, and exposed organisms. Spill simulations in water were carried out with neat diesel and biodiesel and their blends aiming at assessing their genotoxic potentials should there be contaminations of water systems. The water soluble fractions (WSF) from the spill simulations were submitted to solid phase extraction with C-18 cartridge and the extracts obtained were evaluated carrying out genotoxic and mutagenic bioassays [the Salmonella assay and the in vitro MicroFlow® kit (Litron) assay]. Mutagenic and genotoxic effects were observed, respectively, in the Salmonella/microsome preincubation assay and the in vitro MN test carried out with the biodiesel WSF. This interesting result may be related to the presence of pollutants in biodiesel derived from the raw material source used in its production chain. The data showed that care while using biodiesel should be taken to avoid harmful effects on living organisms in cases of water pollution.     

Determination and comparison of nitrated-polycyclic aromatic hydrocarbons measured in air and diesel particulate reference materials

The National Institute of Standards and Technology has issued numerous environmental matrix standard reference materials (SRMs) for the measurement of polycyclic aromatic hydrocarbons; however, only one SRM (diesel particulate material) was issued with certified and reference values for four nitrated-polycyclic aromatic hydrocarbons (nitro-PAH). The objective of this study was to develop an improved analytical procedure to quantify 28 mononitro- and dinitro-PAHs, including numerous isomers, in air and diesel particulate SRMs. Two air particulate matrix SRMs, SRM 1649a Urban Dust and SRM 1648 Urban Particulate Matter, and fine particulate matter, collected from Baltimore MD for use as an "interim reference material" for the determination of organic contaminants, have been characterized for nitro-PAHs. Concentrations of nitro-PAHs in all three air particulate materials were at the ng/g level with the highest nitro-PAH concentration being 2-nitrofluoranthene (range between 246 and 340 ng/g). For the three diesel particulate-related SRMs, SRM 1650a Diesel Particulate Matter, SRM 1975 Diesel Particulate Extract, and SRM 2975 Diesel Particulate Matter (Industrial Fortlift), concentrations of nitro-PAHs were in the microg/g range, with 1-nitropyrene as the dominant nitro-PAH (range between 18 and 40 microg/g). Distinct nitro-PAH isomer patterns were present between the air and diesel particulate materials. These results will provide isomer identification and reference concentrations for a large number of nitro-PAHs in the existing diesel and air particulate SRMs. Published by Elsevier Science Ltd.     

Changes in concentration of five PCDD/F congeners after cooking beef from treated cattle

A large piece of meat taken from a single animal, which had been dosed with five selected PCDD/Fs, was prepared and cooked by a selection of different methods; burgers (fried, grilled, barbecued), roasts (cooked using conventional and microwave ovens) and stews (open pan and pressure cooked). For some of the cooking methods, concentration changes, on a whole product basis, were observed between raw and cooked product. However, in all cases these could be explained simply through changes arising from loss of water and elimination of PCDD/Fs with released fat. The total amounts of PCDD/Fs present in the system (including in released fat) remained unchanged. Dietary intake of PCDD/Fs could therefore be reduced by the removal of visible fat from meat before cooking and by discarding any fat released from foods during the cooking process.     

Preparation and certification of a reference material on PCBs in pig fat and its application in quality control in monitoring laboratories during the Belgian "PCB-crisis"

In this article, the production and validation of a new certified reference material "PCBs in animal fat" for the control of the maximum level of 200 ng/g setup by the European Communities for veterinary products from Belgium is described. Three materials are established: a blank, one material with about 100 ng/g and one with about 200 ng/g (sum of seven PCBs). Data on the production and certification are given. Additionally, this material was used as an unknown test material in the quality assurance program of the Belgium meat monitoring system (before the certification of the material). While the certification was performed with an uncertainty of less than 10%, the round robin exhibited larger deviations. However, these deviations were less than 20% for most of the 30 participating laboratories. Only two had significantly higher deviations.     

Particulate emissions from a stationary engine fueled with ultra-low-sulfur diesel and waste-cooking-oil-derived biodiesel

Stationary diesel engines, especially diesel generators, are increasingly being used in both developing countries and developed countries because of increased power demand. Emissions from such engines can have adverse effects on the environment and public health. In this study, particulate emissions from a domestic stationary diesel generator running on ultra-low-sulfur diesel (ULSD) and biodiesel derived from waste cooking oil were characterized for different load conditions. Results indicated a reduction in particulate matter (PM) mass and number emissions while switching diesel to biodiesel. With increase in engine load, it was observed that particle mass increased, although total particle counts decreased for all the fuels. The reduction in total number concentration at higher loads was, however, dependent on percentage of biodiesel in the diesel-biodiesel blend. For pure biodiesel (B100), the reduction in PM emissions for full load compared to idle mode was around 9%, whereas for ULSD the reduction was 26%. A large fraction of ultrafine particles (UFPs) was found in the emissions from biodiesel compared to ULSD. Nearly 90% of total particle concentration in biodiesel emissions comprised ultrafine particles. Particle peak diameter shifted from a smaller to a lower diameter with increase in biodiesel percentage in the fuel mixture.     

Evaluation of PCDD/Fs characterization in animal feed and feed additives

Safety control of feed and feed additives is necessary to have safe food of animal origin. Based on media reports, nine incidents regarding dioxins and/or PCBs contaminations occurred worldwide during the last decade. Korea is a country which imports feed and feed additives. In this study, various kinds of feed and feed additives were analyzed to monitor the contamination level of dioxins. The level of PCDD/Fs in fish oil was the highest with a concentration of 23.33ngkg(-1), which is equivalent to a toxicological concentration of 4.68ngWHO-TEQ/kg. Feed from animals origin such as chicken meal, animal fat, fish meal, fish oil, and shell powder showed relatively higher concentrations of PCDD/Fs. Feed from plants origin, minerals, and additives ranged from non-detects for bit pulp and ethoxyquin to 8.28ngkg(-1) for dl-methionine. From a toxicological point of view, the highest concentration in vitamins was 0.08ngWHO-TEQ/kg among the feed additives. 2,3,4,7,8-PeCDF was the dominant congener in samples of fish oil, fish meal, and shell powder. Animal fat showed that the pattern of PCDD/Fs depends on the sources of contamination. A sample of animal fat showed 1,2,3,4,7,8-HxCDF and the other sample showed 1,2,3,4,7,8-HxCDD as a primary congener. Generally, low levels of PCDDs were detected in feed additives. Patterns of PCDD/Fs in choline chloride were different with that in choline chloride from an incident in Europe in 2000.     

Solid phase speciation of arsenic by sequential extraction in standard reference materials and industrially contaminated soil samples

Availability, mobility, (phyto)toxicity and potential risk of contaminants is strongly affected by the manner of appearance of elements, the so-called speciation. Operational fractionation methods like sequential extractions have been applied for a long time to determine the solid phase speciation of heavy metals since direct determination of specific chemical compounds can not always be easily achieved. The three-step sequential extraction scheme recommended by the BCR and two extraction schemes based on the phosphorus-like protocol proposed by Manful (1992, Occurrence and Ecochemical Behaviours of Arsenic in a Goldsmelter Impacted Area in Ghana, PhD dissertation, at the RUG) were applied to four standard reference materials (SRM) and to a batch of samples from industrially contaminated sites, heavily contaminated with arsenic and heavy metals. The SRM 2710 (Montana soil) was found to be the most useful reference material for metal (Mn, Cu, Zn, As, Cd and Pb) fractionation using the BCR sequential extraction procedure. Two sequential extraction schemes were developed and compared for arsenic with the aim to establish a better fractionation and recovery rate than the BCR-scheme for this element in the SRM samples. The major part of arsenic was released from the heavily contaminated samples after NaOH-extraction. Inferior extraction variability and recovery in the heavily contaminated samples compared to SRMs could be mainly contributed to subsample heterogeneity.     

Particulate Emissions from a Stationary Engine Fueled with Ultra-Low-Sulfur Diesel and Waste-Cooking-Oil-Derived Biodiesel

ABSTRACT

Stationary diesel engines, especially diesel generators, are increasingly being used in both developing countries and developed countries because of increased power demand. Emissions from such engines can have adverse effects on the environment and public health. In this study, particulate emissions from a domestic stationary diesel generator running on ultra-low-sulfur diesel (ULSD) and biodiesel derived from waste cooking oil were characterized for different load conditions. Results indicated a reduction in particulate matter (PM) mass and number emissions while switching diesel to biodiesel. With increase in engine load, it was observed that particle mass increased, although total particle counts decreased for all the fuels. The reduction in total number concentration at higher loads was, however, dependent on percentage of biodiesel in the diesel-biodiesel blend. For pure biodiesel (B100), the reduction in PM emissions for full load compared to idle mode was around 9%, whereas for ULSD the reduction was 26%. A large fraction of ultrafine particles (UFPs) was found in the emissions from biodiesel compared to ULSD. Nearly 90% of total particle concentration in biodiesel emissions comprised ultrafine particles. Particle peak diameter shifted from a smaller to a lower diameter with increase in biodiesel percentage in the fuel mixture.

IMPLICATIONS There has been an increased usage of stationary diesel engines, especially backup power generators to meet the growing energy demand. Biodiesel derived from waste cooking oil has received increasing attention as an alternative fuel. However, data are only sparsely available in the literature on particulate emissions from stationary engines, fueled with blends of diesel and biodiesel. This study provides insights into the influence of waste-cooking-oil-derived biodiesel on engine performance and the particulate emissions from a stationary engine. The results of the study form a scientific basis to evaluate the impact of biodiesel emissions on the environment and human health.     

Toxaphene in minke whales (Balaenoptera acutorostrata) from the North Atlantic

Toxaphene contamination of minke whales (Balaenoptera acutorostrata) from North Atlantic waters was examined for the first time. Total toxaphene and SigmaCHB (sum of 11 chlorobornanes) concentrations in blubber samples ranged from 170+/-110 and 41+/-39 ng/g lipid weight (l.w.) for female minke whales from southeastern Greenland to 5800+/-4100 and 1100+/-780 ng/g l.w. for males from the North Sea, respectively. Very large variations in toxaphene concentrations among sampling areas were observed suggesting a spatial segregation of minke whales. However, much of the apparent geographical discrimination was explained by the seasonal fluctuation of animal fat mass. Patterns of CHBs in males revealed that recalcitrant CHBs were in higher proportions in animals from the more easterly areas than in animals from the more westerly areas. This trend may be influenced by the predominance of the US, over the European, input of toxaphene to North Atlantic waters.     

Changes in water quality of treated sewage effluents by their receiving environments in Tablas de Daimiel National Park,Spain

The Tablas de Daimiel National Park (TDNP), a floodplain wetland located in the Upper Guadiana Basin (central Spain), receives pollution from wastewater treatment plants (WWTPs) discharging their treated sewage effluents (TSEs) to tributary channels to the wetland. The TSEs suffer transformations on their way to the TDNP, but the water quality is controlled only at the point of discharge. In this work, we analyse the change in water quality of the TSE from four urban WWTPs in the surroundings of the TDNP (Alcázar de San Juan, Daimiel, Manzanares and Villarrubia de los Ojos towns). The water samples were taken at the outlet of the plants and in the receiving environments, to analyse the water quality transformation of the TSE. The different discharge configurations of each WWTP have been related with the water quality transformation of their TSE, to interpret the influence of the hydro-geomorphology in the improvement or deterioration of the water quality of TSE. We found that the discharge of TSE into slow flow channels with macrophyte vegetation facilitates water self-purification but, with time, the accumulation of sludge in the beds of the effluents tends to be the cause of the deterioration of the water quality.     

Perfluorinated Surfactants in Surface and Drinking Waters (9 pp)

Background, Aim and Scope In this paper recent results are provided of an investigation on the discovery of 12 perfluorinated surfactants (PS) in different surface and drinking waters (Skutlarek et al. 2006 a, Skutlarek et al. 2006 b). In the last years, many studies have reported ubiquitous distribution of this group of perfluorinated chemicals, especially perfluorooctane sulfonate (PFOS) and perfluorooctanoic acid (PFOA) in the environment, particularly in wildlife animal and human samples (Giesy and Kannan 2001, Houde et al. 2006, Prevedouros et al. 2006). Perfluorinated surfactants (e.g. PFOS and PFOA) have shown different potentials for reproductory interference and carcinogenity in animal experiments as well as partly long half-lives in humans (Guruge et al. 2006, FSA UK 2006a, FSA UK 2006b, 3M 2005, OECD 2002, Yao and Zhong 2005). They possess compound-dependent extreme recalcitrance against microbiological and chemical degradation and, in addition, they show variable potentials for bioaccumulation in animals and humans (Houde et al. 2006). Materials and Methods: Surface and drinking water samples were collected from different sampling sites: - Surface waters: samples taken from the rivers Rhine, Ruhr, Moehne and some of their tributaries. Further samples were taken from the Rhine-Herne-Canal and the Wesel-Datteln-Canal. - Drinking waters: samples taken in public buildings of the Rhine-Ruhr area. After sample clean-up and concentration by solid-phase extraction, the perfluorinated surfactants were determined using HPLC-MS/MS. Results: All measured concentrations (sum of seven mainly detected components) in the Rhine river and its main tributaries (mouths) were determined below 100 ng/L. The Ruhr river (tributary of the Rhine) showed the highest concentration (94 ng/L), but with a completely different pattern of components (PFOA as major component), as compared with the other tributaries and the Rhine river. Further investigations along the Ruhr river showed remarkably high concentrations of PS in the upper reaches of the Ruhr river and the Moehne river (tributary of the Ruhr) (Ruhr: up to 446 ng/L, Moehne: up to 4385 ng/L). The maximum concentration of all drinking water samples taken in the Rhine-Ruhr area was determined at 598 ng/L with the major component PFOA (519 ng/L). Discussion: The surface water contaminations most likely stem from contaminated inorganic and organic waste materials (so-called 'Abfallgemisch'). This waste material was legally applied to several agricultural areas on the upper reaches of the Moehne. Perfluorinated surfactants could be detected in some suchlike soil samples. They contaminated the river and the reservoir belonging to it, likely by superficial run-off over several months or probably years. Downstream, dilution effects are held responsible for decreasing concentrations of PS in surface waters of the Moehne and the Ruhr river. In analogy to the surface water samples, PS (major component PFOA) can be determined in many drinking water samples of the Rhine-Ruhr area where the water supplies are mainly based on bank filtration and artificial recharge. Conclusions: The concentrations found in drinking waters decreased with the concentrations of the corresponding raw water samples along the flow direction of the Ruhr river (from east to west) and were not significantly different from surface water concentrations. This indicates that perfluorinated surfactants are at present not successfully removed by water treatment steps. Recommendations and Perspectives: Because of their different problematic properties (persistence, mobility, toxicity, bioaccumulation), the concentrations of specific perfluorinated surfactants and their precursors in drinking waters and food have to be minimised. Therefore, it is of utmost importance to take the initiative to establish suitable legal regulations (limitations/ban) concerning the production and use of these surfactants and their precursors. Furthermore, it is indispensable to protect water resources from these compounds. A discussion on appropriate limit values in drinking water and foodstuffs is urgently needed. Concerning the assumed soil contamination, the corresponding regulation (Bioabfall-Verordnung 1998 – Regulation on Organic Waste 1998) should be extended to allow the control of relevant organic pollutants.     

The effect of spent bleaching earth ageing process on its physicochemical and microbial composition and its potential use as a source of fatty acids and triterpenes

This study was aimed at investigating the physicochemical and microbiological changes that took place during the ageing process of spent bleaching earth in the presence of autochthonous microorganisms. Research material included fresh spent bleaching earth (SBE₀) and the same material after 3 years of storage at the constant temperature of 20 °C, without aeration and moistening (SBE₃). Changes in the chemical composition of analysed waste material were observed during its ageing process point to a spontaneous bioconversion of fat substance towards formation and/or release of free saturated fatty acids C16:0 and C18:0 (14.3 g 100 g^?1 D.M.), triterpenes (8.48 g 100 g^?1 D.M.), cholesterol (3.29 g 100 g^?1 D.M.), small quantities of carbohydrates and esters (0.80 g 100 g^?1 D.M.). This process was accompanied by other changes in physicochemical parameters of the waste material, such as colour, odour and viscosity, decrease in fat content from 28.27 to 24.6 % and that of soluble forms of metals (Mo, Cu, Fe, Zn, Ni, Cr and Mn), ranging from 25 to 75 %, and an increase in pH, from 3.85 to 4.2. At the same time, changes in the microbial consortium were observed.     

Polychlorinated dibenzo-p-dioxins, -dibenzofurans, and biphenyls in domestic animal food stuff and their fat

Concentrations of polychlorinated dibenzo-p-dioxins (PCDDs), dibenzo-p-dioxins (PCDFs) and dioxin-like coplanar PCBs and 2,3,7,8-tetrachlorodibenzo-p-dioxin equivalents (TEQs) were measured in domestic animal related samples such as feed ingredient, mixed feed and animal fat from Japan. The mean concentration of total PCDDs, PCDFs and coplanar PCBs in fish oil was 17000pg g-1 lipid wt, which 9- to 30-fold greater than that from other animal originated ingredients. Mixed feed for chicken and chicken fat contained greater total PCDDs, PCDFs, coplanar PCBs concentrations (190 and 2100pg g-1 lipid wt) compared to those for pig (120 and 320pg g-1 lipid wt). WHO-TEQs were ranged 0.39-13, 0.15-0.22 and 0.73-2.8pg g-1 lipid wt for ingredients, mixed feeds and animal fats, respectively. Greater biomagnification factor was noticed for congeners 1,2,3,7,8-PeCDD, 1,2,3,6,7,8-HxCDD, 2,3,7,8-TCDF and 1,2,3,4,7,8-HxCDF in chicken and pig fat. Biomagnification factors for both mono- and non-ortho coplanar PCBs were greater in chicken fat compared to those in pig fat.