High adsorption of dyes by water hyacinth fixed on alginate

Pollution from synthetic dyes has emerged to be a significant environmental issue over the past few decades. This has mainly been triggered by the increasing global dye production, possible toxic effects, undesirable colour and high persistence in the environment. Biosorption, which involves dye removal from aqueous solution by passive linkage in live and dead biomass, has shown great potential in removing dyes from aquatic environments. Among aquatic macrophytes, water hyacinth, Eichhornia crassipes, has shown great potential as a biosorbent. In this work, we investigated the removal of two basic dyes, methylene blue and crystal violet, using E. crassipes immobilized on alginate. Results showed that the Langmuir model better described the equilibrium sorption data when compared to the Freundlich model. Optimum amounts of methylene blue and crystal violet dyes were adsorbed in the alkaline pH range (8–10), 8 % biomass dose, and the amount of dye removed increased with increasing initial dye concentration. The equilibrium monocomponent adsorption capacities for the dyes were 111.1 and 43.5 mg/g, while the binary adsorption capacities were 26.1 and 11.6 mg/g for methylene blue and crystal violet, respectively. To conclude, we show for the first time that E. crassipes fixed on alginate beads can uptake and adsorb methylene blue and crystal violet dyes very effectively in batch systems and show great potential for dye removal from aquatic environments.     

Efficient arsenic depollution in water using modified maize powder

This article reports the synthesis of an efficient, low-cost material from maize powder to depollute arsenic-contaminated water. Arsenic is toxic for humans and other organisms even at low concentrations. The most well-known and severe case of arsenic poisoning through drinking water has been found in India and Bangladesh. Numerous inorganic materials have been tested for the removal of arsenic from water bodies over the last two decades. However, all such materials have several disadvantages such as unpredictable arsenic ion removal, high cost and the generation of toxic sludge that is often more difficult to manage. Alternatively, organic material from agricultural waste may be modified to enrich functional groups responsible for As sorption and, in turn, used to depollute contaminated waters. Here, Zea mays cob powder has been modified to remove arsenic species from water. Two modified materials were produced: an aminated maize powder and a thiolated maize powder. Amination was done using epichlorohydrin and dimethylamine. Thiolation was done using thioglycolic acids. Amination increased As (III) sorption from 70 to 75.8 % and As (V) sorption from 85 to 94.42 %, compared with unmodified maize powder. Thiolation increased As (III) sorption from 70 to 81.7 % and As (V) sorption from 85 to 90 %. Amination increased usability cycles from 3 to 5. Thiolation increased usability cycles from 3 to 6. The novel modified maize biosorbent has enough potential for the development of a low-cost technological pre-treatment step, prior to high-tech chemical treatments.     

Heavy metal phyto-technologies from Ramsar wetland plants: green approach

Side effects of chemical technologies to remediate hazardous heavy metals paved the way to green phyto-technologies. The present research investigated the effectiveness of wetland plants Lemna minor (duckweed), Azolla pinnata (water fern), and Eichhornia crassipes (water hyacinth) pertaining to synchronised removal of heavy metals (Fe, Zn, Cu, Cr, and Cd) from a Ramsar site of an Indo-Burma global biodiversity hot spot region. These plants were grown at different concentrations (1.0, 2.0, and 5.0?mg/L) of metals in microcosm investigation. To this end, the result indicated high removal (>90%) of different metals during 15 days of the experiment. Furthermore, maximum removal was noted on the 12th day of the experiment. Also, results revealed that E. crassipes was the most efficient for the removal of heavy metals followed by L. minor and A. pinnata. Results from analysis confirmed the accumulation of metals within the macrophytes and a corresponding decrease of metals in the wastewater. Significant correlations between metal concentration, water, and wetland plants were obtained. To this end, wetland plants accumulated heavy metals within their tissues, leading to physiological/biochemical alterations. Selected plants exhibited a wide range of stress tolerance to all of the metals and therefore might be utilised for eco-removal of heavy metals from contaminated water. Finally, issues of phytosynthesis of nanoparticles, phytomining, and bioenergy have been critically discussed to attain a sustainability paradigm in the use of phyto-technologies for a green future in the environment sector.     

Polyaniline films for efficient removal of aromatic acids from water

Adsorbents in the form of powders are commonly used to filtrate organic compounds in waters. However, this technique requires the separation of the solid phase from the solution after adsorption experiments. Here we propose the use of films as adsorbents. We synthesized polyaniline films by chemical oxidative polymerization of aniline on red ceramic brick. This film was tested to remove trimellitic, hemimellitic and pyromellitic acids as model molecules of the biodegradation of aquatic humic substances. We evaluated the effect of pH, contact time and initial concentration. Our results show that optimal adsorption conditions required 45 min of solid/liquid contact at pH 7 and an initial concentration of 20 mg/l. The maximum adsorption capacities for hemimellitic, trimellitic and pyromellitic acids are 154.83 for hemimellitic acid, 161.88 for trimellitic acid and 175.26 mg/g for pyromellitic acid. The adsorption efficiency of the polyaniline film decreased only by 13 % after four cycles. Overall, we conclude that polyaniline films are promising separable adsorbents compared to conventional adsorbents for removal of aromatic polycarboxylic acids from water.     

Effect of lime on speciation of heavy metals during composting of water hyacinth

Composting is attractive and inexpensive method for treatment and biomass disposal of water hyacinth. However, the major disadvantage of water hyacinth composting is the high content of heavy metals in the final compost. Addition of lime sludge significantly reduced most bioavailable fractions (exchangeable and carbonate) of heavy metals. Studies were carried on composting of water hyacinth (Eichhornia crassipes) with cattle manure and sawdust (6:3:1 ratio) and effects of addition of lime (1%, 2% and 3%) on heavy metal speciation were evaluated during 30 days of composting period. The Tessier sequential extraction method was employed to investigate the changes in speciation of heavy metals such as Zinc (Zn), Copper (Cu), Manganese (Mn), Iron (Fe), Lead (Pb), Nickel (Ni), Cadmium (Cd) and Chromium (Cr) during water hyacinth composting. Effects of physicochemical parameters such as temperature, pH and organic matter on speciation of heavy metals were also studied during the process. Results showed that, the total metal content was increased during the composting process. The higher reduction in bioavailability factor (BF) of Cu, Fe, Ni, Cd and Cr was observed in lime 2 treatment about 62.1%, 64.4%, 71.9%, 62.1% and 58.9% respectively; however higher reduction in BF of Zn and Pb was observed in lime 1 treatment during the composting process. Reducible and oxidizable fractions of Ni, Pb and Cd were not observed during the process. Addition of lime was very effective for reduction of bioavailability of heavy metals during composting of water hyacinth with cattle manure and sawdust.     

Removal of arsenate from water by adsorbents: a comparative case study

Laboratory and field filtration experiments were conducted to study the effectiveness of As(V) removal for five types of adsorbent media. The media included activated alumina (AA), modified activated alumina (MAA), granular ferric hydroxide (GFH), granular ferric oxide (GFO), and granular titanium dioxide (TiO₂). In laboratory batch and column experiments, the synthetic challenge water was used to evaluate the effectiveness for five adsorbents. The results of the batch experiments showed that the As(V) adsorption decreased as follows at pH 6.5: TiO₂ > GFO > GFH > MAA > AA. At pH 8.5, however, As(V) removal decreased in the following order: GFO = TiO₂ > GFH > MAA > AA. In column experiments, at pH 6.5, the adsorbed As(V) for adsorbents followed the order: TiO₂ > GFO > GFH, whereas at pH 8.5 the order became: GFO = TiO₂ > GFH when the challenge water containing 50 μg/L of As(V) was used. Field filtration experiments were carried out in parallel at a wellhead in New Jersey. Before the effluent arsenic concentration increased to 10 μg/L, approximately 58,000 and 41,500 bed volumes of groundwater containing an average of 47 μg/L of As(V) were treated by the filter system packed with GFO and TiO₂, respectively. The As(V) adsorption decreased in the following sequence: GFO > TiO₂ > GFH > MAA > AA. Filtration results demonstrated that GFO and TiO₂ adsorbents could be used as media in small community filtration systems for As(V) removal.     

Characteristics,sources and health risk assessment of toxic heavy metals in PM<Subscript>2.5</Subscript> at a megacity of southwest China

Twenty trace elements in fine particulate matters (i.e., PM_2.5) at urban Chengdu, a southwest megacity of China, were determined to study the characteristics, sources and human health risk of particulate toxic heavy metals. This work mainly focused on eight toxic heavy metal elements (As, Cd, Cr, Cu, Mn, Ni, Pb and Zn). The average concentration of PM_2.5 was 165.1 ± 84.7 µg m^?3 during the study period, significantly exceeding the National Ambient Air Quality Standard (35 µg m^?3 in annual average). The particulate heavy metal pollution was very serious in which Cd and As concentrations in PM_2.5 significantly surpassed the WHO standard. The enrichment factor values of heavy metals were typically higher than 10, suggesting that they were mainly influenced by anthropogenic sources. More specifically, the Cr, Mn and Ni were slightly enriched, Cu was highly enriched, while As, Cd, Pb and Zn were severely enriched. The results of correlation analysis showed that Cd may come from metallurgy and mechanical manufacturing emissions, and the other metals were predominately influenced by traffic emissions and coal combustion. The results of health risk assessment indicated that As, Mn and Cd would pose a significant non-carcinogenic health risk to both children and adults, while Cr would cause carcinogenic risk. Other toxic heavy metals were within a safe level.     

Adsorption of phosphate ions from water using a novel cellulose-based adsorbent

A novel cellulose-based adsorbent, iron(III)-coordinated amino-functionalised poly(glycidylmethacrylate)-grafted cellulose [Fe(III)–AM-PGMACell] was developed for the removal of phosphate from water and wastewater. The scanning electron micrograph showed that AM-PGMACell has a rougher surface than cellulose and the adsorption of Fe(III) on AM-PGMACell made the surface even rougher. Infrared spectroscopy revealed that amino groups on the surface of AM-PGMACell complexed with Fe(III) played an important role in the removal of phosphate from solutions. X-Ray diffraction patterns showed a decrease in crystallinity after graft copolymerisation onto cellulose. The effects of contact time, initial sorbate concentration, pH, agitation speed, dose of adsorbent and temperature on the removal process were investigated. Maximum removal of 99.1% was observed for an initial concentration of 25 mg·L ^?1 at pH 6.0 and an adsorbent dose of 2.0 g·L ^?1. A two-step pseudo-first-order kinetic model and Sips isotherm model represented the measured data very well. Complete removal of 11.6 mg·L ^?1 phosphate from fertiliser industry wastewater was achieved by 1.6 g·L ^?1 Fe(III)–AM-PGMACell. The adsorbent exhibited very high reusability for several cycles. Overall, the study demonstrated that Fe(III)–AM-PGMACell can be used as an efficient adsorbent for the removal and recovery of phosphate from water and wastewater.     

Calcareous electrochemical precipitation,a new method to trap nickel in seawater

There are few efficient, rapid and cheap methods to remove toxic metals from contaminated waters. Here we hypothesised that cathodic protection, an existing method used to control the corrosion of metallic structures, may trap toxic metals. Indeed, in seawater, the application of a cathodic current on a metallic structure induces the precipitation of limestone (CaCO₃) and magnesium dihydroxyde (Mg(OH)₂), thus forming a calcareous deposit on the metal surface. We therefore presumed that such calcareous deposit may trap metals dissolved in waters. Actually calcareous deposit formation has never been studied in the presence of dissolved metallic contaminants such as nickel. Here we tested ionic nickel (Ni²⁺) precipitation in calcareous deposit with a galvanized steel electrode by spiking artificial seawater with a NiCl₂ salt during 7 days of applied current. We analysed deposit surface and cross section by µ-Raman spectroscopy and scanning electron microscopy (SEM) with X-ray microanalysis. Ni concentration in the deposit was quantified by inductively coupled plasma analysis, after deposit dissolution in 60% HNO₃. Results show that in 7 days up to 24% of nickel can be trapped in the calcareous deposit. Scanning electron microscopy reveals that Ni is trapped under a pure CaCO₃ layer of aragonite. Raman spectra show that nickel is incorporated as nickel dihydroxyde (Ni(OH)₂), as evidence by vibration bands at 446 and 510 cm^?1. Overall our findings disclose a new and efficient method, calcareous electrochemical precipitation, which has potential applications to remove toxic metals from contaminated waters.     

Characterization of boron tolerant bacteria isolated from a fly ash dumping site for bacterial boron remediation

Boron is an essential micronutrient for plants, but can above certain concentrations be toxic to living organisms. A major environmental concern is the removal of boron from contaminated water and fly ash. For this purpose, the samples were collected from a fly ash dumping site, Nagasaki prefecture, Japan. The chemical characteristics and heavy metal concentration of the samples were performed by X-ray fluorescent analysis and leaching test. For bacterial analysis, samples were collected in sterile plastic sheets and isolation was carried out by serial dilution method. The boron tolerant isolates that showed values of maximum inhibitory concentration toward boron ranging from 100 to 260 mM level were screened. Based on 16S rRNA sequencing and phylogenetic analysis, the isolates were most closely related to the genera Bacillus, Lysinibacillus, Microbacterium and Ralstonia. The boron tolerance of these strains was also associated with resistant to several heavy metals, such as As (III), Cr (VI), Cd, Cu, Pb, Ni, Se (III) and Zn. Indeed, these strains were arsenic oxidizing bacteria confirmed by silver nitrate test. These strains exhibited their salt resistances ranging from 4 to 15 % were determined in Trypticase soy agar medium. The boron tolerant strains were capable of removing 0.1–2.0 and 2.7–3.7 mg l^?1 boron from the medium and fly ash at 168 h. Thus, we have successfully identified the boron tolerant and removal bacteria from a fly ash dumping site for boron remediation.     

Variability in the chemistry of private drinking water supplies and the impact of domestic treatment systems on water quality

Tap water from 497 properties using private water supplies, in an area of metalliferous and arsenic mineralisation (Cornwall, UK), was measured to assess the extent of compliance with chemical drinking water quality standards, and how this is influenced by householder water treatment decisions. The proportion of analyses exceeding water quality standards were high, with 65 % of tap water samples exceeding one or more chemical standards. The highest exceedances for health-based standards were nitrate (11 %) and arsenic (5 %). Arsenic had a maximum observed concentration of 440 µg/L. Exceedances were also high for pH (47 %), manganese (12 %) and aluminium (7 %), for which standards are set primarily on aesthetic grounds. However, the highest observed concentrations of manganese and aluminium also exceeded relevant health-based guidelines. Significant reductions in concentrations of aluminium, cadmium, copper, lead and/or nickel were found in tap waters where households were successfully treating low-pH groundwaters, and similar adventitious results were found for arsenic and nickel where treatment was installed for iron and/or manganese removal, and successful treatment specifically to decrease tap water arsenic concentrations was observed at two properties where it was installed. However, 31 % of samples where pH treatment was reported had pH < 6.5 (the minimum value in the drinking water regulations), suggesting widespread problems with system maintenance. Other examples of ineffectual treatment are seen in failed responses post-treatment, including for nitrate. This demonstrates that even where the tap waters are considered to be treated, they may still fail one or more drinking water quality standards. We find that the degree of drinking water standard exceedances warrant further work to understand environmental controls and the location of high concentrations. We also found that residents were more willing to accept drinking water with high metal (iron and manganese) concentrations than international guidelines assume. These findings point to the need for regulators to reinforce the guidance on drinking water quality standards to private water supply users, and the benefits to long-term health of complying with these, even in areas where treated mains water is widely available.     

Modelling the concentrations of dissolved contaminants (Cd,Cu, Ni,Pb, Zn) in floodplain soils

Central European floodplain soils are often contaminated with potentially toxic metals. The prediction of their aqueous concentrations is a prerequisite for an assessment of environmental concerns. We tested the aqueous concentrations of cadmium (Cd), copper (Cu), nickel (Ni), lead (Pb) and zinc (Zn) derived from multi-surface adsorption modelling (on hydrous iron, aluminum and manganese oxides, clay and soil organic matter) against those analyzed in situ in the soil solution of four horizons of floodplain soils at the Elbe River, Germany. The input data for the reactive metals were derived from a seven-step sequential extraction scheme or from extraction with 0.43 M nitric acid (HNO₃) and evaluated in four modelling scenarios. In all scenarios, measured and modelled concentrations were positively related, except partially for Pb. Close reproduction of the measured data was obtained using measured data of accompanying cations and anions together with amounts of reactive metals from both the sequential extraction or from 0.43 M HNO₃ extraction, except for Cu, which was often strongly overestimated, and partially Cd. We recommend extraction with 0.43 M HNO₃ to quantify reactive metals in soil because the modelling results were metal-specific with better or equal results using the single extractant, the application of which is also less laborious. Approximations of ion concentrations and water contents yielded similar results. Modelled solid-phase speciation of metals varied with pH and differed from that from sequential extraction. Multi-surface modelling may be an effective tool to predict both aqueous concentrations and solid-phase speciation of metals in soil.     

Removal of Mercury from Polluted Waters by the Water Hyacinth (Eichhornia crassipes)

The uptake of mercury by water hyacinth (Eichhornia crassipes) was studied in an outdoor experiment for 25 days at different metal concentrations. the removal of mercury from the water and uptake by plants was very effective during the first hours and decreased rapidly thereafter. the uptake of mercury was directly proportional to the initial concentration in the water. the highest concentrations were found in plant roots. According to the results, water hyacinth could be used for treatment of mercurial waste waters.     

Pomegranate husk as an adsorbent in the removal of toxic chromium from wastewater

The use of a new sorbent developed from the husk of pomegranate, a famous fruit in Egypt, for the removal of toxic chromium from aqueous solution has been investigated. The batch experiment was conducted to determine the adsorption capacity of the pomegranate husk. The effects of initial metal concentration (25 and 50 mg l^?1), pH, contact time, and sorbent concentration (2–6 g l^?1) have been studied at room temperature. A strong dependence of the adsorption capacity on pH was observed, the capacity increased as the pH decreased, and the optimum pH value was pH 1.0. Adsorption equilibrium and kinetics were studied with different sorbent and metal concentrations. The adsorption process was fast, and equilibrium was reached within 3 h. The maximum removal was 100% for 25 mg l^?1 of Cr⁶⁺ concentration on 5 g l^?1 pomegranate husk concentration, and the maximum adsorption capacity was 10.59 mg g^?1. The kinetic data were analysed using various kinetic models—pseudo-first-order, pseudo-second-order, Elovich, and intraparticle diffusion equations—and the equilibrium data were tested using several isotherm models, Langmuir, Freundlich, Tempkin, Dubinin–Radushkevich, and Generalized isotherm equations. The Elovich and pseudo-second-order equations provided the greatest accuracy for the kinetic data, while Langmuir and Generalized isotherm models were the closest fit for the equilibrium data. The activation energy of sorption has also been evaluated as 0.236 and 0.707 kJ mol^?1 for 25 and 50 mg l^?1 chromium concentration, respectively.     

Modelling the kinetics and equilibrium properties of cadmium biosorption by river green alga and water hyacinth weed

Cadmium biosorption properties of non-living, dried river green alga from a river source, and water hyacinth weed, Eichhornia crassipes from a lake in Zimbabwe have been investigated. The cadmium uptake was found to depend on initial pH, uptake being apparently minimal at low pH values and increasing with an increase in pH. Cadmium biosorption kinetics by both samples is fast, with 80% of total uptake occurring within 60?min. The effect of initial solution pH and initial cadmium concentration on cadmium biosorption from a cadmium solution has been studied. The data for algal biomass fitted the Langmuir monolayer adsorption isotherm, while the biosorption of the metal by water hyacinth weed fitted the Freundlich adsorption isotherm with 1/n values all less than 1. Maximum metal uptake capacities were recorded using 0.35?g of biomass and a 250?mg?L^?1 cadmium solution at pH 6.5 and at 25°C and these were about 85 and 50?mg?L^?1 for water hyacinth weed and green alga, respectively, showing that water hyacinth weed offered a greater potential for cadmium uptake. The absorption was described by pseudo-second order rate model and the rate constant and equilibrium sorption capacity are reported.     

Anthropogenic metal pollution in surface sediments of the Tambaraparni River Estuary

Estuarine sediments in the<63 μm size fraction were collected from 15 stations within the Tambaraparni River Estuary, located on the east coast of India. The distribution of the heavy metals Cd, Co, Cr, Cu, Ni, Pb and Zn was recorded. Our analysis distinguished two groups of elements. First, Cd, Pb and Zn, which occurred in higher than expected concentrations indicative of pollution, and second, Co, Cr, Cu and Ni, which occurred at background levels. The highest metal concentration found in the study area was for Zn (1200 μ g·g^?1), and the lowest was for Cd (0.42 μ g·g^?1). It is presumed that river run-off, industrial waters and untreated domestic waters are major contributors to heavy metal pollution in the Tambaraparni River Estuary. The concentrations of heavy metal species in surface sediments (<2 m water depth) of the Tambaraparni Estuary were studied to determine the extent of anthropogenic inputs from catchment areas and to understand anthropogenic effects on geochemical process in this tropical estuarine system.     

Unexpected removal of the most neutral cationic pharmaceutical in river waters

Contamination of surface waters by pharmaceuticals is now widespread. There are few data on their environmental behaviour, particularly for those which are cationic at typical surface water pH. As the external surfaces of bacterio-plankton cells are hydrophilic with a net negative charge, it was anticipated that bacterio-plankton in surface-waters would preferentially remove the most extensively-ionised cation at a given pH. To test this hypothesis, the persistence of four, widely-used, cationic pharmaceuticals, chloroquine, quinine, fluphenazine and levamisole, was assessed in batch microcosms, comprising water and bacterio-plankton, to which pharmaceuticals were added and incubated for 21 days. Results show that levamisole concentrations decreased by 19 % in microcosms containing bacterio-plankton, and by 13 % in a parallel microcosm containing tripeptide as a priming agent. In contrast to levamisole, concentrations of quinine, chloroquine and fluphenazine were unchanged over 21 days in microcosms containing bacterio-plankton. At the river-water pH, levamisole is 28 % cationic, while quinine is 91–98 % cationic, chloroquine 99 % cationic and fluphenazine 72–86 % cationic. Thus, the most neutral compound, levamisole, showed greatest removal, contradicting the expected bacterio-plankton preference for ionised molecules. However, levamisole was the most hydrophilic molecule, based on its octanol–water solubility coefficient (K _ow). Overall, the pattern of pharmaceutical behaviour within the incubations did not reflect the relative hydrophilicity of the pharmaceuticals predicted by the octanol–water distribution coefficient, D _ow, suggesting that improved predictive power, with respect to modelling bioaccumulation, may be needed to develop robust environmental risk assessments for cationic pharmaceuticals.     

Removal of Mercury from Polluted Waters by the Water Hyacinth (Eichhornia crassipes)

The uptake of mercury by water hyacinth (Eichhornia crassipes) was studied in an outdoor experiment for 25 days at different metal concentrations. the removal of mercury from the water and uptake by plants was very effective during the first hours and decreased rapidly thereafter. the uptake of mercury was directly proportional to the initial concentration in the water. the highest concentrations were found in plant roots. According to the results, water hyacinth could be used for treatment of mercurial waste waters.     

Selective recovery of Cu, Zn, and Ni from acid mine drainage

In Korea, the heavy metal pollution from about 1,000 abandoned mines has been a serious environmental issue. Especially, the surface waters, groundwaters, and soils around mines have been contaminated by heavy metals originating from acid mine drainage (AMD) and mine tailings. So far, AMD was considered as a waste stream to be treated to prevent environmental pollutions; however, the stream contains mainly Fe and Al and valuable metals such as Ni, Zn, and Cu. In this study, Visual MINTEQ simulation was carried out to investigate the speciation of heavy metals as functions of pH and neutralizing agents. Based on the simulation, selective pH values were determined to form hydroxide or carbonate precipitates of Cu, Zn, and Ni. Experiments based on the simulation results show that the recovery yield of Zn and Cu were 91 and 94 %, respectively, in a binary mixture of Cu and Zn, while 95 % of Cu and 94 % of Ni were recovered in a binary mixture of Cu and Ni. However, the recovery yield and purity of Zn and Ni were very low because of similar characteristics of Zn and Ni. Therefore, the mixture of Cu and Zn or Cu and Ni could be recovered by selective precipitation via pH adjustment; however, it is impossible to recover selectively Zn and Ni in the mixture of them.     

Heavy metals and soil microbes

Heavy metal pollution is a global issue due to health risks associated with metal contamination. Although many metals are essential for life, they can be harmful to man, animal, plant and microorganisms at toxic levels. Occurrence of heavy metals in soil is mainly attributed to natural weathering of metal-rich parent material and anthropogenic activities such as industrial, mining, agricultural activities. Here we review the effect of soil microbes on the biosorption and bioavailability of heavy metals; the mechanisms of heavy metals sequestration by plant and microbes; and the effects of pollution on soil microbial diversity and activities. The major points are: anthropogenic activities constitute the major source of heavy metals in the environment. Soil chemistry is the major determinant of metal solubility, movement and availability in the soil. High levels of heavy metals in living tissues cause severe organ impairment, neurological disorders and eventual death. Elevated levels of heavy metals in soils decrease microbial population, diversity and activities. Nonetheless, certain soil microbes tolerate and use heavy metals in their systems; as such they are used for bioremediation of polluted soils. Soil microbes can be used for remediation of contaminated soils either directly or by making heavy metals bioavailable in the rhizosphere of plants. Such plants can accumulate 100 mg g^?1 Cd and As; 1000 mg g^?1 Co, Cu, Cr, Ni and 10,000 mg g^?1 Pb, Mn and Ni; and translocate metals to harvestable parts. Microbial activity changes soil physical properties such as soil structure and biochemical properties such as pH, soil redox state, soil enzymes that influence the solubility and bioavailability of heavy metals. The concept of ecological dose (ED₅₀) and lethal concentration (LC₅₀) was developed in response to the need to easily quantify the influence of pollutants on microbial-mediated ecological processes in various ecosystems.