Formulation of a Photosensitized Polyethylene Film; Its Structure and Property Variation Under the Weathering Conditions of Tehran

To develop an environmentally degradable polymer material, a masterbatch pro-oxidant system was blended into low-density polyethylene. The polymer film samples were prepared by compression molding. The prepared films were placed under the natural environment of Tehran for weathering studies and accelerated conditions were also performed for UV aging in UV chamber. At different time intervals, the changes in chemical structure of photosensitized polyethylene samples were studied by FTIR and compared to that of the control polyethylene films. Also the mechanical properties of photosensitized polyethylene films were determined in comparison with the control films by measuring the tensile strength and elongation at break after exposure to the natural environment and UV radiation. Results showed that the overall rate of degradation process is clearly dependent on the polyethylene composition, test conditions (natural or accelerated), season of the year, and the duration of the weathering of the samples.     

Compatibilization Improves Performance of Biodegradable Biopolymer Composites Without Affecting UV Weathering Characteristics

With growing interest in the use of eco-friendly composite materials, biodegradable polymers and composites from renewable resources are gaining popularity for use in commercial applications. However, the long-term performance of these composites and the effect of compatibilization on their weathering characteristics are unknown. In this study, five types of biodegradable biopolymer/wood fiber (WF) composites were compatibilized with maleic anhydride (MA), and the effect of accelerated UV weathering on their performance was evaluated against composites without MA and neat biopolymers. The composite samples were prepared with 30 wt% wood fiber and one of the five biodegradable biobased polymer: poly(lactic) acid (PLA), polyhydroxybutyrate (PHB), poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV), Bioflex (PLA blend), or Solanyl (starch based). Neat and composite samples were UV weathered for 2000 h (hours), and characterized for morphological, physical, thermal, and mechanical properties before and after weathering. Compared to composites without MA, composites containing MA grafted polymers exhibited improved properties due to increased interfacial adhesion between the fiber and matrix. Upon accelerated weathering, thermal and mechanical properties of 70% of the samples substantially decreased. Surfaces of all the samples were roughened, and drastic color changes were observed. Water absorption of all the samples increased after weathering exposure. Even though the compatibilization is shown to improve composite properties before weathering, it did not affect weathering of samples, as there were no considerable differences in properties exhibited by the composites with MA and without MA after weathering. The results suggest that compatibilization improves properties of biodegradable biobased composites without affecting its UV degradation properties.     

Effect of Reprocessing and Accelerated Weathering on ABS Properties

The feasibility of reprocessing has been investigated as a possible alternative for acrylonitrile–butadiene–styrene terpolymer (ABS) recycling. Up to 10 reprocessing cycles have been performed by both extrusion and injection techniques and their effect on thermal and mechanical properties have been studied. Moreover, the effect of the combined reprocessing and accelerated weathering has been analyzed. Measurements collected after each molding cycle indicated virtually complete retention of thermal properties. The same behaviour has been observed from accelerated weathering tests. With respect to the mechanical properties, neither the flow index nor the tensile strength were affected by the number of reprocessing cycles though the impact strength decreased slightly. However, the studies based on the accelerated weathering show that there is an important influence of the number of reprocessing cycles on the tensile strength.     

Effects of Natural and Artificial Weathering on the Physical Properties of Recycled Poly(ethylene terephthalate)

In accelerated weathering tests, specimens are exposed to higher radiation intensity, temperature and humidity than is likely under natural weathering in order to achieve rapid degradation of the polymer in a convenient short time. In the current work, a correlation between the two environments is attempted so that a prediction of lifetimes in the natural environment can be achieved. During aging, surface flaws are created due to the chain scission process. This is initiated by the absorption of ultra-violet light and directly affects visual appearance and impact strength. After natural weathering, the material shows only plastic deformation in an impact test. However, after artificial weathering to 5000 h of UV exposure, there is a decrease of 85% in impact strength. Colour change occurs at a high rate in the early stages of UV exposure. Beyond 2000 h of exposure, the colour change approaches a steady state and a correlation between the changes under natural and artificial weathering becomes apparent for a potential prediction of lifetimes. From the analysis including the specular component (SCI), taking surface roughening into account, 1 year under natural weathering was found to be equivalent to 25 days under accelerated weathering.     

Physical Morphology and Quantitative Characterization of Chemical Changes of Weathered PVC/Pine Composites

This study investigated weathering effects on polyvinyl chloride (PVC) based wood plastic composites (WPC), with a focus on the color and structure that is attributed to the material composition. It is directed towards quantifying the main chemical modifications, such as carbonyl and vinyl groups which are formed during weathering. These composites were subjected to three weathering regimes: exterior, accelerated xenon-arc, and accelerated UVA. The change in color was monitored using colorimetry. Fourier transform infrared spectroscopy was used to identify and quantify the chemical modifications (carbonyl formation and vinyl propagation) due to weathering. Additionally, scanning electron microscopy was employed to observe the physical morphological changes that occurred. The results showed that exterior and accelerated xenon-arc and UVA weathering regimes increased the degree of lightness, total color change, carbonyl concentration, and wood loss on the surfaces of the weathered composites. The increased carbonyl concentration during weathering implied that degradation had occurred by oxidation process. Also, oxidation and lignin (from the wood) degradation influenced the color (lightness) of PVC based WPC upon weathering.     

Soil Biodegradation of PHBV/Peach Palm Particles Biocomposites

There is great interest in developing eco-friendly green biocomposites from plant-derived natural fibers and crop-derived bioplastics attributable to their renewable resource-based origin and biodegradable nature. Fully biodegradable composites, made from both biodegradable polymeric matrices and natural fibers, should be advantageous in some applications, such as one way packaging. Polyhydroxyalkanoates (PHAs) are naturally occurring biodegradable polymers produced from a wide range of microorganisms, with poly(3-hydroxybutyrate) P(3HB) and poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) being important examples of PHAs. In this work, biocomposites of PHBV consisting of a PHBV matrix incorporating peach palm particles (PPp), [i.e., 100/0, 90/10, 80/20 and 75/25 (%w/w) PHBV/PPp] were processed by injection molding at 160 °C. The effect of PPp loading on the thermal and the mechanical properties, as well as on the morphological behavior of the PHBV/PPp biocomposites was investigated. Soil biodegradation tests were carried out by burying specimen beakers containing aged soil and kept under controlled temperature and humidity in accordance with ASTM G160-98. Degradation of the biocomposites was evaluated by visual analysis, scanning electron microscopy (SEM) and thermogravimetric analysis (TGA) following test exposures of up to 5 months. The addition of PPp reduced the maximum strength and the elongation at break of the biocomposites. On the other hand, the Young’s modulus improved with the PPp content. Micrographs of the fracture surfaces following tensile strength testing revealed a large distance between the PHBV matrix and PPp particles although a low interaction is expected. Where measured, these distances tended increase as the PPp content of the biocomposites increased. Soil biodegradation tests indicated that the biocomposites degraded faster than the neat polymer due to the presence of cavities that resulted from introduction of the PPp and that degradation increased with increasing PPp content. These voids allowed for enhanced water adsorption and greater internal access to the soil-borne degrader microorganisms.     

Novel Biocomposites Sheet Molding Compounds for Low Cost Housing Panel Applications

Biocomposites were made by a novel high volume processing technique named biocomposite sheet molding compound panel (BCSMCP) manufacturing process. This process design was inspired by the commercial glass fiber–polyester resin composite fabrication method called sheet molding compounding (SMC). This process yields continuous production of biocomposites on a large scale, and thus can be easily adopted in industries. A unique fiber dispersion method, which enabled uniform distribution of natural fibers, was used in this process. Consistency of the process was tested by evaluating the repeatability of the resultant materials mechanical properties. The low cost biocomposites produced as a result of the processing will be used for various panel applications such as housing and transportation. The molded samples were tested for various mechanical and thermal properties, in accordance with ASTM procedures. The biocomposites were made with various natural fibers including, big blue stem grass, jute, and industrial hemp. By combining different natural fibers in varying mass fractions, hybrid biocomposites were made using this process. Grass fiber reinforced polyester biocomposites processed by the SMC line showed very promising results.     

Sustainable Cellular Biocomposites from Natural Fibers and Unsaturated Polyester Resin for Housing Panel Applications

Increased environmental awareness and interest in long-term sustainability of material resources has motivated considerable advancements in composite materials made from natural fibers and resins, or biocomposites. In spite of these developments the lower stiffness and strength of biocomposites has limited their applications to non-load-bearing components. This paper presents an overview of a study aimed at showing that the shortcomings of biocomposites can be overcome through hybrid material designs and efficient structural configurations to make them suitable for load bearing structural components. Hybrid blends of natural and synthetic fibers can significantly improve the characteristics of biocomposites with minimal cost and environmental impact, and hierarchical cellular designs can maximize material efficiency in structural components. Periodic and hierarchical cellular plate designs made from natural fibers and unsaturated polyester resin were evaluated experimentally and analytically. Stiffness, strength, and dimensional stability of all-biocomposite and hybrid natural–synthetic material systems were evaluated through material tests while structural performance of cellular plate designs was assessed through flexural tests on laboratory-scale samples. The experimental results were correlated with analytical models for short-fiber composites and cellular structures. The results showed that biocomposites have adequate short-term performance and that they can efficiently compete with housing panels made from conventional structural materials.     

Durability of PCL Nanocomposites Under Different Environments

The stability of PCL/TiO₂ nanocomposites under different environments was investigated. Samples were exposed to UV radiation in an accelerated weathering chamber equipment and characterized by viscosimetry and differential scanning calorimetry. The results showed that the presence of nanoparticles containing titanium enhanced polymer chain scission during UV exposure. For all samples, the melting temperature and crystallinity increased along photodegradation time. The biodegradability, assessed by biochemical oxygen demand, increased as the amount of inorganic particles increased. However, the thermal stability and activation energy evaluated by thermogravimetric analysis decreased as the amount of inorganic nanoparticles increased, indicating that nanocomposites exhibited lower thermal stability.     

Interactive Influence of Biofiber Composition and Elastomer on Physico-Mechanical Properties of PLA Green Composites

The objective of this work was to improve the impact and thermal properties of polylactic acid (PLA)-based biocomposite by appropriate application of cellulosic fiber and a bioelastomer. Biocomposites formulations with fiber contents of up to 20% in combination with a bioelastomer were extrusion-compounded in a twin-screw extruder followed by molding in an injection molding system. Fibers used in the formulations included three types of cellulosic fiber; namely, raw fiber from oat hull biomass (RF), hydrolysis byproduct (ATF) which was the solid fraction obtained from an acid-catalyzed hydrolysis of RF, and delignified fibers (AD30, AD65, AD100) which were the products of delignification of ATF. Formulated biocomposites were characterized for thermal (glass transition and melting temperatures, and enthalpy of melting) and physico-mechanical (tensile and bending strengths, stiffness, impact energy, and water absorption) properties. Among all types of biofibers, RF resulted in poor properties in the biocomposites due to the high hemicellulose content in the structure. On the other hand, the ratio of lignin to cellulose (in the absence of hemicellulose) in the modified fibers did not significantly affect the physico-mechanical and thermal properties of the biocomposites. The elastomer applied in the formulations improved the impact energy, thermal properties, and elongation at break of the composites. However, it adversely affected the strength and water resistance of biocomposites, especially in the presence of hemicellulose. The results indicated that, depending on the application, a wide range of PLA green composites with different physico-mechanical properties can be achieved.     

Wood Modification Effects on Weathering of HDPE-Based Wood Plastic Composites

The effects of weathering on the constituents of wood and polymer matrix behavior in wood plastic composites (WPCs) were investigated. WPCs were produced from pine, extractives-free pine, and pine holocellulose fibers (60%) together with HDPE (40%). These composites were subjected to xenon-arc accelerated and outside weathering for a total of 1200 h and 120 days, respectively. The color and chemical changes that occurred on the surface of the WPCs were analyzed using a set of analytical techniques. For pine and extractive-free pine filled composites, the results showed that the total color change, lightness, and oxidation increased, while the lignin content decreased. In addition, the weight average molecular weight (Mw) and number average molecular weight (Mn) of extracted HDPE decreased with an increase in exposure time of the composites. However, HDPE crystallinity increased with longer exposure time. Lightness of holocellulose-based WPC changed the least while the change in its HDPE crystallinity was not significant compared to the other composite types. Therefore, holocellulose-based WPC may be preferred for applications where color stability is of high priority.     

Synergistic Effect of TNPP and Carbon Black in Weathered XLPE Materials

Carbon black is one of the most widely used and most effective ultraviolet (UV) light stabilizers for plastics applications. Several important segments of the plastics industry rely on carbon black for UV stabilization of weather-resistant products, including telecommunications, power cable jacketing, and plastic pipes. In this research work a combination of Trisnonylphospate (TNPP) antioxidant and different size carbon black were applied in crosslinked polyethylene (XLPE) to improve its wetherability. The primary reason for cross-linking polyethylene (PE) is to raise the thermal stability of the material under load. This substantially improves environmental stress crack resistance and resistance to slow crack growth. The results achieved of this additive package combination show a synergism effect and improved weatherability of electrical cable. Increased weathering lifetime was also achieved. Further, we were able to confirm in this work, that the size and quality of the carbon black dispersion in a XLPE samples is an important component of both the UV-resistance and mechanical properties of the finished plastic article. Incremental improvements of carbon black dispersion can positively influence the expected life of plastic articles. Mechanical testing and FTIR were used to detect degradation of the accelerated weathered XLPE samples. The morphological considerations of UV energy absorption and presents laboratory data demonstrating the link between dispersion and weatherability as well as between morphology and weatherability     

Performance of Cow Dung Reinforced Biodegradable Poly(Lactic Acid) Biocomposites for Structural Applications

In this work, performance of cow dung (CD) reinforced poly(lactic acid) (PLA) biocomposites was investigated for the potential use in load bearing application. CD of average 4 mm size was blended with PLA at different CD ratios (0–50 wt%) and their effects on the biocomposite properties were studied. The results showed an improvement in the flexural properties, while the tensile and impact strength dropped by 20 and 28% with the addition of 50% CD. The decline in the tensile and impact strength was due to micro-cracking and voids formation at higher CD content. Also, the incorporation of CD slightly decreased the thermal stability of the biocomposite. However, dynamic mechanical properties of the biocomposites generally improved. SEM analysis of tensile and impact fractured surfaces indicated that the CD had a reasonable adhesion with matrix. Moreover, the SEM micrographs of soil burial studies showed an accelerated degradation of higher CD wt% biocomposites.     

Injection Molded Biocomposites from Soy Protein Based Bioplastic and Short Industrial Hemp Fiber

Biocomposites from soy based bioplastic and chopped industrial hemp fiber were fabricated using twin-screw extrusion and injection molding process. Soy based bioplastics were prepared through cooking with plasticizer and blending with biodegradable poly(ester amide). Mechanical, thermal properties and fracture surface morphology of the “green”/biocomposites were evaluated with universal testing system (UTS), dynamic mechanical analysis (DMA), Environmental Scanning Electron Microscopy (ESEM). It was found that the tensile strength and modulus, flexural strength and modulus, impact strength and heat deflection temperature of industrial hemp fiber reinforced biocomposites significantly improved. The fracture surfaces showed no signs of matrix on the fiber surface suggesting poor interfacial adhesion.     

Effect of <Emphasis Type="Italic">Moringa oleifera</Emphasis> Pod Husk Fibers on the Properties of Gelatin-Based Biocomposite

The objective of this work is to study the feasibility of reinforcing polymer composites by utilizing the biofibers from the agricultural residue of Moringa oleifera pod husks (MOPH). The chemical and physical properties of the fibers were comprehensively investigated to evaluate their potential as a filler in gelatin-based films. The effect of MOPH fiber concentrations of 0, 5, 10, and 15 wt% on the water vapor permeability (WVP), and mechanical and thermal properties of the gelatin-based films was studied. By incorporation of 10 wt% of the MOPH fibers in gelatin, the highest tensile strength and Young’s modulus, and the lowest WVP properties were obtained. Scanning electron microscopy (SEM) photographs indicated good interfacial adhesion between the fibers and the gelatin matrix. TGA of the biocomposites revealed an improvement of thermal stability. Moreover, under accelerated weathering, the gelatin-MOPH-10% biocomposite degraded more slowly than the gelatin control. These results indicate that the MOPH fibers are a good reinforcing filler and may be useful for biocomposite applications.     

Performance of Pultruded Jute Fibre Reinforced Phenolic Composites as Building Materials for Door Frame

The pultruded jute/phenolic composites were aged under various humidity, hydrothermal and weathering conditions. Aging-induced effect of these conditions on the jute profiles was studied in terms of their physico-mechanical properties. It is observed that dimensional change of the profiles was only upto 4% even in an accelerated water aging condition. The effect of absorbed moisture/water on the jute profile was more pronounced in an accelerated water aging than the samples are being exposed to high humidity and alternate wetting and drying cycles. The changes in the values of internal bond strength of the profiles could be used as an indicator because of its sensitivity towards aging. Accentuation of fibres on the weathered samples along with severe resin erosion has suggested to layer the surface of the profiles with rich resin prior to use in the outdoor. The properties of jute profile door frame were satisfactory when compared with the requirements mentioned in IS: 4021–83 – Indian standard specification for timber door, window and ventilator frames. Performance of the installed door frame has shown no sign of dimensional instability in terms of warping and bulging after 3 years. It is suggested that jute door frames could be used as an alternative to the wooden door frames in buildings.     

拜耳法赤泥制备三聚磷酸铝

拜耳法赤泥经石灰石烧结改性、盐酸浸取及碱液处理等工序得到氢氧化铝干胶,再以氢氧化铝干胶和工业磷酸为原料,通过中和反应、缩合反应和水化反应合成三聚磷酸铝.经单因素条件实验和正交实验得到最佳工艺条件为:磷酸体积(mL)与氢氧化铝干胶质量(g)的比3,中和反应温度常温,缩合反应温度290℃,缩合反应时间4h.在最佳工艺条件下合成的试样中,Al2O3和P2O5的含量与工业三聚磷酸铝ATP-200相近,经IR分析,该试样即为三聚磷酸铝.盐雾试验结果表明合成的三聚磷酸铝的防腐性能达到ATP-200的性能指标.     

Instrumental Physical Analysis of Microwaved Glycerol Citrate Foams

Solid glycerol citrate polyester polymeric foams generated by microwave heating were further cured in a conventional oven at 100?°C for 0, 6, 24, 48, or 72?h and their physical properties were tested. Curing glycerol citrate polyesters resulted in decreased moisture content (MC), altered color, increased hydrated polymer weight loss (HWL), and increased polymer oven weight loss (OWL). Polyester polymer samples were evaluated for firmness and springiness employing a texture analyzer (Model TA/TX2i). Oven curing increased polymer firmness and springiness. For example, firmness and springiness in 48?h cured samples increased 202 and 143%, respectively, when compared to uncured controls. High correlations were found comparing OWL, MC, HWL, firmness, and springiness. Compression molded samples obtained from ground cured and non-cured polymers were evaluated for tensile strength, elongation and Young??s modulus using the Instron universal test machine (Model 4201). Curing promoted higher tensile strengths and elongation but did not affect Young??s modulus values. High correlations were found between springiness, firmness, tensile strength, and elongation. The texture analyzer was shown to have merit in the preliminary evaluation of the glycerol citrate polyester polymers.     

Steam gasification of epoxy circuit board in the presence of carbonates

To recover useful metals from end-of-life electronic devices and to convert plastic components from these devices into clean fuel gas, steam gasification of epoxy board samples was carried out at 600–700?°C and 0.1?MPa pressure in the presence of a ternary eutectic carbonate (lithium carbonate, sodium carbonate, and potassium carbonate). Hydrogen and carbon dioxide were the main products, and methane and carbon monoxide were detected as minor products. The gasification proceeded in two steps: an initial rapid pyrolysis followed by secondary steam gasification of char produced from the pyrolysis. The ternary eutectic carbonate accelerated not only the latter steam gasification but also the initial rapid pyrolysis. The activation energy for the steam gasification of epoxy board samples in the presence of the carbonate was 122?kJ/mol.     

Bioabsorbable Soy Protein Plastic Composites: Effect of Polyphosphate Fillers on Biodegradability

The use of biodegradable polymers made from renewable agricultural products such as soy protein isolate has been limited by the tendency of these materials to absorb moisture. A straightforward approach for controlling the inherent water absorbency of the biodegradable polymers involves blending special bioabsorbable polyphosphate fillers, biodegradable soy protein isolate, plasticizer, and adhesion promoter in a high-shear mixer followed by compression molding. The procedure yields a relatively water-resistant, biodegradable soy protein polymer composite, as previously reported. The aim of the present study is to determine the biodegradability of the new polyphosphate filler/soy protein plastic composites by monitoring the carbon dioxide released over a period of 120 days. The results suggest that the composites biodegrade satisfactorily, with the fillers having no significant effect on the depolymerization and mineralization of the soy protein plastic, processes that would otherwise result in nonbiodegradable composites. Further, the results indicate that the biodegradation and useful service life of these biocomposites may be controlled by changing the filler concentration, making the biocomposites useful in applications in which the control of water resistance and biodegradation is critical.