A Method for Removal of CO from Exhaust Gas Using Pulsed Corona Discharge

ABSTRACT

An experimental study of the oxidation of CO in exhaust gas from a motorcycle has been carried out using plasma chemical reactions in a pulsed corona discharge. In the process, some main parameters, such as the initial CO concentration, amplitude and frequency of pulses, residence time, reactor volume, and relative humidity (RH), as well as their effects on CO removal characteristics, were investigated. O₃, which is beneficial to reducing CO, was produced during CO removal . When the exhaust gas was at ambient temperature, more than 80% CO removal efficiency was realized at an initial concentration of 288 ppm in a suitable range of the parameters.     

Control of diesel gaseous and particulate emissions with a tube-type wet electrostatic precipitator

In this study, experiments were performed with a bench-scale tube-type wet electrostatic precipitator (wESPs) to investigate its effectiveness for the removal of mass- and number-based diesel particulate matter (DPM), hydrocarbons (HCs), carbon monoxide (CO), and oxides of nitrogen (NOx) from diesel exhaust emissions. The concentration of ozone (O3) present in the exhaust that underwent a nonthermal plasma treatment process inside the wESP was also measured. A nonroad diesel generator operating at varying load conditions was used as a stationary diesel emission source. The DPM mass analysis was conducted by means of isokinetic sampling and the DPM mass concentration was determined by a gravimetric method. An electrical low-pressure impactor (ELPI) was used to quantify the DPM number concentration. The HC compounds, n-alkanes, and polycyclic aromatic hydrocarbons (PAHs) were collected on a moisture-free quartz filter together with a PUF/XAD/PUF cartridge and extracted in dichloromethane with sonication. Gas chromatography (GC)/mass spectroscopy (MS) was used to determine HC concentrations in the extracted solution. A calibrated gas combustion analyzer (Testo 350) and an O3 analyzer were used for quantifying the inlet and outlet concentrations of CO and NOx (nitric oxide [NO] + nitrogen dioxide [NO2]), and O3 in the diesel exhaust stream. The wESP was capable of removing approximately 67-86% of mass- and number-based DPM at a 100% exhaust volumetric flow rate generated from 0- to 75-kW engine loads. At 75-kW engine load, increasing gas residence time from approximately 0.1 to 0.4 sec led to a significant increase of DPM removal efficiency from approximately 67 to more than 90%. The removal of n-alkanes, 16 PAHs, and CO in the wESP ranged from 31 to 57% and 5 to 38%, respectively. The use of the wESP did not significantly affect NOx concentration in diesel exhaust. The O3 concentration in diesel exhaust was measured to be less than 1 ppm. The main mechanisms responsible for the removal of these pollutants from diesel exhaust are discussed.     

Control of Diesel Gaseous and Particulate Emissions with a Tube-Type Wet Electrostatic Precipitator

Abstract

In this study, experiments were performed with a bench-scale tube-type wet electrostatic precipitator (wESPs) to investigate its effectiveness for the removal of mass- and number-based diesel particulate matter (DPM), hydrocarbons (HCs), carbon monoxide (CO), and oxides of nitrogen (NO_x) from diesel exhaust emissions. The concentration of ozone (O₃) present in the exhaust that underwent a nonthermal plasma treatment process inside the wESP was also measured. A nonroad diesel generator operating at varying load conditions was used as a stationary diesel emission source. The DPM mass analysis was conducted by means of isokinetic sampling and the DPM mass concentration was determined by a gravimetric method. An electrical low-pressure impactor (ELPI) was used to quantify the DPM number concentration. The HC compounds, n-alkanes, and polycyclic aromatic hydrocarbons (PAHs) were collected on a moisture-free quartz filter together with a PUF/XAD/PUF cartridge and extracted in dichloromethane with sonication. Gas chromatography (GC)/mass spectroscopy (MS) was used to determine HC concentrations in the extracted solution. A calibrated gas combustion analyzer (Testo 350) and an O₃ analyzer were used for quantifying the inlet and outlet concentrations of CO and NO_x (nitric oxide [NO] + nitrogen dioxide [NO₂]), and O₃ in the diesel exhaust stream. The wESP was capable of removing approximately 67–86% of mass- and number-based DPM at a 100% exhaust volumetric flow rate generated from 0- to 75-kW engine loads. At 75-kW engine load, increasing gas residence time from approximately 0.1 to 0.4 sec led to a significant increase of DPM removal efficiency from approximately 67 to more than 90%. The removal of n-alkanes, 16 PAHs, and CO in the wESP ranged from 31 to 57% and 5 to 38%, respectively. The use of the wESP did not significantly affect NO_x concentration in diesel exhaust. The O₃ concentration in diesel exhaust was measured to be less than 1 ppm. The main mechanisms responsible for the removal of these pollutants from diesel exhaust are discussed.     

Bench-scale biofilter for removing ammonia from poultry house exhaust

A bench-scale biofilter was evaluated for removing ammonia (NH3) from poultry house exhaust. The biofilter system was equipped with a compost filter to remove NH3 and calcium oxide (CaO) filter to remove carbon dioxide (CO2). Removal of NH3 and CO2 from poultry house exhaust could allow treated air with residual heat to be recirculated back into the poultry house to conserve energy during winter months. Apart from its use as a plant nutrient, NH3 removal from poultry house exhaust could lessen the adverse environmental impacts of NH3 emissions. Ammonia and CO2 were measured daily with gas detector tubes while temperatures in the poultry pen and compost filter were monitored to evaluate the thermal impact of the biofilter on treated air. During the first 37 days of the 54-day study, exhaust air from 33 birds housed in a pen was treated in the biofilter; for the final 17 days, NH3-laden exhaust, obtained by applying urea to the empty pen was treated in the biofilter. The biofilter system provided near-complete attenuation of a maximum short-term NH3 concentration of 73 ppm. During the last 17 days, with a mean influent NH3 concentration of 26 ppm, the biofilter provided 97% attenuation. The CaO filter was effective in attenuating CO2. Compared with a biofilter sized only for NH3 removal, an oversized biofilter would be required to provide supplemental heat to the treated air through exothermic biochemical reactions in the compost. The biofilter could conserve energy in poultry production and capture NH3 for use as plant nutrient. Based on this study, a house for 27,000 broilers would require a compost filter with a volume of approximately 34 m3.     

氨水土壤混合物脱除CO2温室气体的实验研究

为了脱除CO2温室气体,提出了利用氨水土壤混合物去除CO2的新方法。分别考察了土壤颗粒粒径、CO2初始流量、氨水浓度（质量比）和温度对CO2脱除量和脱除率的影响。实验结果表明,该方法去除CO2的量较土壤物理吸附量和氨水化学吸收量的总和提高了大约15%;随着氨水浓度的增大,CO2的脱除率和脱除量都增大;随着土壤颗粒粒径和CO2初始流量的增大,CO2的脱除率和脱除量都减小;当温度由22℃升高到31℃,CO2的脱除率随着温度的升高而增大,但是继续升高温度到40℃,CO2的脱除率反而下降。     

氨水土壤混合物脱除CO2温室气体的实验研究

为了脱除CO2温室气体,提出了利用氨水土壤混合物去除CO2的新方法.分别考察了土壤颗粒粒径、CO2初始流量、氨水浓度(质量比)和温度对CO2脱除量和脱除率的影响.实验结果表明,该方法去除CO2的量较土壤物理吸附量和氨水化学吸收量的总和提高了大约15%;随着氨水浓度的增大,CO2的脱除率和脱除量都增大;随着土壤颗粒粒径和CO2初始流量的增大,CO2的脱除率和脱除量都减小;当温度由22℃升高到31℃,CO2的脱除率随着温度的升高而增大,但是继续升高温度到40 ℃,CO2的脱除率反而下降.     

Pressurized CO2/zero valent iron system for nitrate removal

A fluidized zero valent iron (ZVI) reactor pressurized by CO(2) gas for controlling pH was employed for nitrate reduction. The proposed CO(2) pressurized system potentially has advantages of using less CO(2) gas and reaching equilibrium pH faster than CO(2)-bubbled system. However, due to weak acid nature of carbonic acid, system pH gradually increased with increasing oxidation of ZVI and reduction of nitrate. As pH increased with progress of reaction, nitrate removal rate decreased continuously. The results indicate that nitrate removal efficiency increases with increasing initial ZVI dosage but reaches plateau at ZVI doses of higher than 8.25gl(-1), and initial nitrate concentration up to 100mg l(-1) as N has minimal impact on the removal efficiency. Unlike the fluidized system with pH control by strong acid reported in our pervious study, near 100% of nitrogen recovery was observed in the current process, indicating that nitrate reduction by ZVI with different pH controlled mechanisms will have different reaction routes.     

Selection and Substantiation of an Organic Solvent Removal Apparatus at a Print Shop by Comparative Experiments Using the Activated Carbon Adsorption and Catalytic Oxidation Methods

ABSTRACT

The investigation of an appropriate organic solvent removal apparatus for installation in a newly reconstructed print shop as a countermeasure for preventing the exhaust of organic solvents was conducted.

The selection of an organic solvent removal apparatus was made after bench-scale tests of the activated carbon adsorption method and the catalytic oxidation method, both of which are effective for the removal of organic solvents, were performed on the actual exhaust gas at the print shop. The results showed that both methods were efficient enough to be applied to the removal of organic solvents, but the activated carbon adsorption method had many drawbacks, such as the need for frequent replacement of activated carbon and complex maintenance. For the catalytic oxidation method, running costs are high, but there are many merits, such as that the catalysts do not have to be replaced as often and maintenance is simple. After considering these factors, a catalytic oxidation removal apparatus was installed at the new print shop. In the results of the substantiation test on the actual apparatus using mixed catalysts of platinum and manganese plus copper, the removal efficiency was 97.998.7% and the concentration of the outlet exhaust gas was about 10 ppm (the average concentration of the inlet exhaust gas was 528 ppm) at a space velocity of 30,000 hr^-1 and a reaction temperature of 200 °C. The results of this study were substantiated.     

Effects of water vapor pretreatment time and reaction temperature on CO(2) capture characteristics of a sodium-based solid sorbent in a bubbling fluidized-bed reactor

CO(2) capture from flue gas using a sodium-based solid sorbent was investigated in a bubbling fluidized-bed reactor. Carbonation and regeneration temperature on CO(2) removal was determined. The extent of the chemical reactivity after carbonation or regeneration was characterized via (13)C NMR. In addition, the physical properties of the sorbent such as pore size, pore volume, and surface area after carbonation or regeneration were measured by gas adsorption method (BET). With water vapor pretreatment, near complete CO(2) removal was initially achieved and maintained for about 1-2min at 50 degrees C with 2s gas residence time, while without proper water vapor pretreatment CO(2) removal abruptly decreased from the beginning. Carbonation was effective at the lower temperature over the 50-70 degrees C temperature range, while regeneration more effective at the higher temperature over the 135-300 degrees C temperature range. To maintain the initial 90% CO(2) removal, it would be necessary to keep the regeneration temperature higher than about 135 degrees C. The results obtained in this study can be used as basic data for designing and operating a large scale CO(2) capture process with two fluidized-bed reactors.     

Absorption and reaction kinetics of amines and ammonia solutions with carbon dioxide in flue gas

The removal system for the absorption of CO2 with amines and NH3 is an advanced air pollution control device to reduce greenhouse gas emissions. Absorption of CO2 by amines and NH3 solutions was performed in this study to derive the reaction kinetics. The absorption of CO2 as encountered in flue gases into aqueous solutions of monoethanolamine (MEA), diethanolamine (DEA), and NH3 was carried out using a stirred vessel with a plane gas-liquid interface at 50 degrees C. Various operating parameters were tested to determine the effect of these variables on the absorption kinetics of the reactants in both gas and liquid phases and the effect of competitions between various reactants on the mass-transfer rate. The observed absorption rate increases with increasing gas-liquid concentration, solvent concentration, temperature, and gas flow rate, but changes with the O2 concentration and pH value. The absorption efficiency of MEA is better than that of NH3 and DEA, but the absorption capacity of NH3 is the best. The active energies of the MEA and NH3 with CO2 are 33.19 and 40.09 kJ/mol, respectively.     

Chemical absorption process for degradation of VOC gas using heterogeneous gas-liquid photocatalytic oxidation: toluene degradation by photo-Fenton reaction

A novel process for degradation of toluene in the gas-phase using heterogeneous gas-liquid photocatalytic oxidation has been developed. The degradation of toluene gas by photo-Fenton reaction in the liquid-phase has experimentally examined. The photo-Fenton reaction in the liquid-phase could improve the overall toluene absorption rate by increasing the driving force for mass transfer and as a result enhance the removal of toluene in the exhaust gas. The toluene concentrations in the inlet gas were varied in the range from 0.0968 to 8.69gm(-3) with initial hydrogen peroxide concentration of 400mgl(-1) and Fe dose of 5.0mgl(-1). It was found that toluene in the inlet gas was almost completely dissolved into water and degraded in the liquid-phase for the inlet toluene gas concentration of less than 0.42gm(-3). The dynamic process of toluene gas degradation by the photo-Fenton reaction providing information for reaction kinetics and mass transfer rate was examined. Toluene removal kinetic analysis indicated that photo-Fenton degradation was significantly affected by H(2)O(2) concentration. The experimental results were satisfactorily described by the predictions simulated using the simplified tanks-in-series model combined with toluene removal kinetic analysis. The present results showed that the proposed chemical absorption process using the photo-Fenton heterogeneous gas-liquid photocatalytic oxidation is very effective for degradation of volatile organic gases.     

利用UVC去除低浓度苯的实验研究

探讨了不同实验参数对苯的UVC去除效果的影响,获得了苯的去除率与苯的初始浓度、气体流量、相对湿度和氧气含量等参数之间的关系。数据表明,在实验条件范围内,苯的去除率的倒数与苯初始浓度、气体流量之间为线性关系;苯的去除率随相对湿度的增加呈现先升高后缓慢降低的关系,最佳相对湿度值在30%～50%之间;苯的去除率随氧气量的增加而缓慢增加;波长为185+254 nm的UV与254 nm的UV相比净化效果更为理想。还分析了苯降解产生的中间产物,探讨了苯的降解机理。     

碳酸根对磷酸钙沉淀反应回收磷的影响

以模拟的厌氧消化液为处理对象,通过小试实验,考察不同初始磷浓度Cp、Ca／P物质的量比、pH和温度下,碳酸根（CO3 2-）对磷酸钙沉淀反应回收磷的影响;利用扫描电镜（SEM）、x射线衍射仪（XRD）和傅里叶变换红外光谱（FT．IR）对沉淀产物进行表征。结果表明,高浓度的CO3 2-对以磷酸钙沉淀反应去除和回收磷的效率影响较大;Cp相同时,CO3 2-浓度（CCO3^2-）越大,P的去除率越低,低C,（20mg／L）时尤为显著;当CCO3^2-相同时,随着Cp的增大,反应速率加快,P的去除率逐渐升高,但升高幅度越来越小;增大Ca／P比和pH能提高P的去除率,降低CO3 2-对磷酸钙沉淀反应的抑制作用,综合考虑实际效果,应选择Ca／P比为3．33,pH为9．0作为适宜的反应条件;升高温度对降低CO3 2-对磷酸钙沉淀反应的抑制作用贡献不大。在Cp为60ITIg／L,Ca／P比为1．67,pH为9．0,温度为20℃的条件下,当CCO3^2-为0时,得到的沉淀产物主要为羟基磷灰石HAP;当CCO3^2-为30mmol／L时,得到的沉淀产物为磷酸钙和碳酸合磷灰石的混合物。     

Removal of carbon dioxide by a spray dryer

With the global warming due to greenhouse effects becoming serious, many efforts are carried out to decrease the emissions of CO2 from the combustion of carbonaceous materials. In Taiwan, there are 19 large-scale municipal solid waste incinerators running and their total emission of CO2 is about 16,950 kton y-1. Spray dryer is the most prevailing air pollution control devise for removing acid gas in waste incineration; however, the performance of spray dryer on the removal of CO2 is seldom studied. This study employs a laboratory-scale spray dryer to investigate the removal efficiency of CO2 under different operating conditions. The evaluated parameters include different absorbents mixed with CaOH2, operating temperature, the concentration of absorbent, and the inlet concentration of CO2. Experimental results show that the best removal efficiency of CO2 by a spray dryer is 48% as the absorbent is 10%NaOH+5%CaOH2 and the operating temperature is 150 degrees C. Comparing this result with previous study shows that the performance of spray dryer is better than traditional NaOH wet scrubber. For NaOH+CaOH2 spray dryer, the removal efficiency of CO2 is decreased with the inlet concentration of CO2 increased and the optimum operating temperature is 150 degrees C. Except NaOH+CaOH2, absorbents DEA+CaOH2, TEA+CaOH2, and single CaOH2 are not effective in removing CO2 by a spray dryer.     

活性炭吸附和脱附-等离子体氧化净化有机废气的研究

根据滑动弧放电等离子体适于降解高浓度有机物废气的特性,结合活性炭吸附法,提出了吸附器的吸附浓缩和热脱附-等离子体氧化净化有机废气的方法。在活性炭吸附过程中,最初2 h内甲苯净化率达到100%,随着时间的增加净化率下降;在热脱附滑动弧放电等离子体净化过程中,甲苯降解效率最高为97.3%。将滑动弧放电等离子体反应器出口气相产物收集进行FT-IR检测,发现放电后有CO2、CO、H2O和NO2产生,并分析了甲苯的降解机理。     

Effect of gas velocity and influent concentration on biofiltration of gasoline off-gas from soil vapor extraction

This study was conducted to evaluate the effects of gas inlet concentration and velocity on the biofiltration of gasoline vapor. Gasoline vapor was treated using a compost biofilter operated in an upflow mode for about 3 months. The inlet concentration of gasoline total petroleum hydrocarbon (TPH) ranged from about 300 to 7000 mgm(-3) and gas was injected at velocities of 6 and 15 mh(-1) (empty bed residence time (EBRT)=10 and 4 min, respectively). The maximum elimination capacities of TPH at 6 and 15 mh(-1) found in this research were over 24 and 19 gm(-3) of filling material h(-1), respectively. TPH removal data was fit using a first-order kinetic relationship. In the low concentration range of 300-3000 mg m(-3), the first-order kinetic constants varied between about 0.10 and 0.29 min(-1) regardless of gas velocities. At TPH concentrations greater than 3000 mgm(-3), the first-order kinetic constants were about 0.09 and 0.07 min(-1) at gas velocities of 6 mh(-1) and 15 mh(-1), respectively. To evaluate microbial dynamics, dehydrogenase activity, CO2 generation and microbial species diversity were analyzed. Dehydrogenase activity could be used as an indicator of microbial activity. TPH removal corresponded well with CO2 evolution. The average CO2 recovery efficiency for the entire biofilter ranged between 60% and 70%. When the gas velocity was 6 mh(-1), most of the microbial activity and TPH removal occurred in the first quarter of the biofilter. However, when the gas velocity was 15 mh(-1), the entire column contributed to removal. Spatial and temporal variations in the biofilter microbial population were also observed. Nearly 60% of the colonies isolated from the compost media prior to biofiltration were Bacillus. After 90 days of biofiltration, the predominant species in the lower portion (0-50 cm) of the filter were Rhodococcus, while Pseudomonas and Acinetobacter dominated the upper portion (75-100 cm).     

Bio-syngas production with low concentrations of CO2 and CH4 from microwave-induced pyrolysis of wet and dried sewage sludge

This paper assesses the feasibility of producing syngas from sewage sludge via two pyrolysis processes: microwave-induced pyrolysis (MWP) and conventional pyrolysis (CP). The changes in the composition of the produced gas as a function of the pyrolysis treatment and the initial moisture content of the sludge were evaluated. It was found that MWP produced a gas with a higher concentration of syngas than CP, reaching values of up to 94vol%. Moreover, this gas showed a CO2 and CH4 concentration around 50% and 70%, respectively, lower than that obtained in the gas from CP. With respect to the effect of moisture on gas composition, this was more pronounced in CP than in MWP. Thus, the presence of moisture increases the concentration of H2 and CO2 and decreases that of CO, especially when CP was used. In order to elucidate the behaviour of CO2 during the pyrolysis, the CO2 gasification kinetics of the char obtained from the pyrolysis were investigated. It was established that in microwave heating the gasification reaction is much more favoured than in conventional heating. Therefore, the low concentration of CO2 and the high concentration of CO in the microwave pyrolysis gas could be due to the self-gasification of the residue by the CO2 produced during the devolatilization of the sewage sludge in the pyrolysis process.     

Removal of gaseous elemental mercury by dielectric barrier discharge

The removal of elemental mercury (Hg(0)) with the reactive species produced from dielectric barrier discharge (DBD) was studied. The effects of the operating parameters, such as the applied voltage, residence time, initial concentration and co-existence of other pollutants, were investigated. The removal of Hg(0) was significantly promoted by an increase in the applied voltage of the DBD reactor system. The presence of NO gas decreased the Hg(0) removal efficiency within the range of input powers tested compared to the case of Hg(0)-only due to the competition for ozone between Hg(0) and NO gas in the DBD reactor.     

生物过滤塔处理实验室废气

研究了生物过滤塔处理实验室排放的模拟混合废气,考察了反应器对苯、甲苯、二甲苯、乙醇、丙酮、乙酸乙酯和甲烷等废气的去除效果。运行结果表明,在设备稳定运行期间,进气中总挥发性有机物(TVOCs)的浓度为124～380 mg/m3,而出气浓度在10～40 mg/m3,去除效率保持在85%以上。实验室废气中的多种污染物在生物过滤塔中去除机理不同,亲水性污染物的去除效率高于疏水性污染物。通过系统关停后重启,污染物的去除效果在第2天就能恢复,这为生物过滤塔处理实验室废气过程的停运检修或者系统闲置提供了可行性。     

静电布袋复合式除尘器及其应用

介绍了静电布袋复合式除尘器的结构、材料及除尘原理;布袋除尘器在不同工况下的除尘效率、附加脱硫率、阻力和排放浓度等参数的测试结果;利用布袋除尘器改造静电除尘器时的改造方案、运行中应注意的问题.