日光下黄砂负载TiO2降解邻氯苯酚水溶液

研究了以黄砂为载体,ＴｉＯ２为催化剂,以太阳光为光源对邻氯苯酚水溶液进行光催化降解的可行性。结果表明,锐钛型ＴｉＯ２邓邻氯苯酚有显著的光催化降解作用;ＴｉＯ２的催化活性在焙烧温度３００℃时最高。     

A new rapid method for quantification of PCBs in transformer oil

In order to improve the efficiency and cost-effectiveness of the PCB analysis, the DMSO partition and SPE extraction were applied to clean up the PCB-contaminated transformer oils and PCB level was determined by means of the quadrupole GC/MS. The analysis data obtained from this method were compared statistically to that from the standard method.     

Use of an ultraviolet light-activated persulfate process to degrade humic substances: effects of wavelength and persulfate dose

Environmental Science and Pollution Research - Natural organic matter (NOM), commonly found in surface and ground waters, form disinfection by-products in drinking water. Generally, advanced...     

Dechlorination of PCBs in the simulative transformer oil by microwave-hydrothermal reaction with zero-valent iron involved

The conventional hydrothermal reaction with iron powder, NaOH and H₂O as reactants was reported to occur at temperature above 423 K, and iron oxides (Fe₃O₄ and NaFeO₂) and hydrogen were produced. In this study, microwave heating was adopted to take the place of conventional heating to induce the hydrothermal reaction. Under microwave irradiation, NaOH and H₂O absorbed microwave energy by space charge polarization and dipolar polarization and instantly converted it into thermal energy, which initiated the hydrothermal reaction that involved with zero-valent iron. X-ray diffraction (XRD) analysis found Fe₃O₄/NaFeO₂ and confirmed the occurrence of microwave-induced hydrothermal reaction. The developed microwave-hydrothermal reaction was employed for the dechlorination of PCBs. Hexadecane containing 100 mg L⁻¹ of Aroclor1254 was used as simulative transformer oil, and the dechlorination of PCBs was evaluated by GC/ECD, GC/MS and ion chromatography. For PCBs in 10 mL simulative transformer oil, almost complete dechlorination was achieved by 750 W microwave irradiation for 10 min, with 0.3 g iron powder, 0.3 g NaOH and 0.6 mL H₂O added. The effects of important factors including microwave power and the amounts of reactants added, on the dechlorination degree were investigated, moreover, the dechlorination mechanism was suggested. Microwave irradiation combined with the common and cheap materials, iron powder, NaOH and H₂O, might provide a fast and cost-effective method for the treatment of PCBs-containing wastes.     

Spectral attenuation of solar ultraviolet radiation in humic lakes in Central Finland

The attenuation of solar ultraviolet (UV) radiation in five lakes in Central Finland was evaluated through field measurements and/or by determining the optical properties of the lake water during summer 1999. Spectral UV irradiance in the air and at several depths underwater was measured in three lakes (Lake Palosj?rvi, Konnevesi, and Jyv?sj?rvi) with dissolved organic carbon (DOC) ranging from 4.9 to 8.7 mg l(-1) and chlorophyll a ranging from 1.6 to 16 g l(-1). According to the field measurements, 99% of the UV-B radiation was attenuated in approximately a half meter water column in the clearest lake. In the UV-A region at 380 nm, the corresponding attenuation occurred in the upper one meter. In a small humic lake (DOC 13.2-14.9 mg l(-1)) UV-B radiation was attenuated to 1% of the subsurface irradiance within the top 10 cm water column, whereas UV-A radiation (at 380 nm) penetrated more than twice as deeply (maximum 25 cm), as predicted from the absorption coefficients. These results suggest the importance of the dissolved fraction of lake water in governing the UV attenuation in lakes. This was seen from the significant relationship between the vertical attenuation coefficients (Kd) based on field measurements and the absorption coefficients (ad) derived from spectrophotometric laboratory scannings, as well as between Kd and DOC.     

Congener profiles of PCBs and PCDD/Fs in Yucheng victims fifteen years after exposure to toxic rice-bran oils and their implications for epidemiologic studies

In 1978-1979, a mass poisoning occurred in central Taiwan from rice-bran oil contaminated by heat-degraded PCBs was later called the Yucheng (oil disease in Chinese). Only a few studies have so far investigated the levels of specific polychlorinated biphenyl (PCB) or polychlorinated dibenzodioxin/furan (PCDD/F) congeners in the Yucheng victims. This study aimed to investigate the serum residual levels of thirty-three PCBs and seventeen 2,3,7,8-substituted PCDD/F congeners in the Yucheng victims 15 years after the exposure. Forty-one blood samples were collected from individual Yucheng victims in 1994-1995. The mean levels of total 33 PCBs and 17 PCDD/Fs were 2468 ng/g lipid (13.3 ng/g sample) and 6550 pg/g lipid (30.9 pg/g sample) respectively. The higher levels were found in PCBs #99, #138, #153, #156, #170, #179, and #180 among 33 PCB congeners, while 2,3,4,7,8-PeCDF, 1,2,3,4,7,8-HxCDF, and OCDD had the higher concentrations among 17 PCDD/F congeners. The total TEQ was contributed in decreasing order by 10 PCDFs (44%), three non-ortho-PCBs (24%), six mono-ortho-PCBs (20%), and seven PCDDs (12%). The mean total PCB levels and TEQ value of the 17 PCDD/Fs in the Yucheng victims 15 years after the toxic exposure were still 9 and 46 times higher than those in the general population in Taiwan. Principle component analysis (PCA) indicated that seven PCB congeners, PCBs #99, #138, #153, #156, #170, #179, and #180, accounted for 73% of the total variances in PCBs. On the other hand, six PCDD/F congeners, 2,3,4,7,8-PeCDF, 1,2,3,4,7,8-HxCDF, 1,2,3,6,7,8-HxCDF, 1,2,3,6,7,8-HxCDD, 1,2,3,4,6,7,8-HpCDF, and OCDD, accounted for 97% of the total variances in PCDD/Fs. In addition, PCA revealed that at least three characteristic patterns of congener profiles for PCBs were observed among the Yucheng victims. Similar trend was also observed for PCDD/Fs. These patterns may reflect distinctive exposure scenarios and/or different metabolizing capabilities among the Yucheng victims. We suggest that these patterns, in contrast to total PCB and PCDD/F levels, may be valuable for the future epidemiologic studies when linking exposure with specific health effect.     

Goethite and lepidocrocite catalyzing different double-oxidant systems to degrade chlorophenol

Environmental Science and Pollution Research - Goethite and lepidocrocite, as the main compositions of pipe deposits in the water distribution network, could be used as a catalyst for advanced...     

Determination of PCDD/Fs and dioxin-like PCBs in fish oils for feed ingredients by congener-specific chemical analysis and CALUX bioassay

The present research was intended to determine the suitability of the CALUX assay as a screening method for dioxins in fish oil used as a feed ingredient in Japan. Alteration of TEQ in fish oil according to newly proposed toxic equivalency factors (TEF) is also discussed. In the analysis, polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) and dioxin-like polychlorinated biphenyls (DL-PCBs) in 41 fish oil samples were determined by using high-resolution gas chromatography/high-resolution mass spectrometry (HRGC/HRMS) and CALUX bioassay. The mean TEQ values derived from 1998 WHO-TEF of PCDD/Fs and DL-PCBs were 2.6 and 9.9 pg g(-1) (ww), respectively. The levels of TEQ derived from the recently re-evaluated 2005 WHO-TEF were slightly lower than those of the former in both groups. Notably, the contribution of mono-ortho DL-PCBs to total 2005 WHO-TEQ was considerably decreased compared to the case of 1998 WHO-TEQ, resulting from the reduction in its TEF values, while the non-ortho DL-PCBs contribution was increased. The mean TEQ determined by CALUX assay for PCDD/Fs was approximately three times higher, whereas DL-PCBs was approximately two times lower than WHO-TEQ determined by HRGC/HRMS; the sum of PCDD/Fs and DL-PCBs was very similar by both methods. The correlation coefficients of TEQ between the CALUX assay and HRGC/HRMS analysis were 0.84, 0.89, and 0.90 for PCDD/Fs, DL-PCBs, and the sum, respectively. These results suggest that the CALUX assay is a very useful method for the screening of dioxin-related compounds in fish oils.     

Environmental exposure to PCBs and cancer incidence in eastern Slovakia

In a population-based cross-sectional study, we compared serum levels of 15 polychlorinated biphenyl (PCB) congeners and three organochlorine pesticides in residents of two districts in eastern Slovakia, one with extensive environmental contamination from a former PCB production site (Michalovce) and the other matched on geography but with low (background) levels (Svidnik). The age-adjusted geometric means for sum of 15 measured PCB congeners were statistically significantly higher in subjects from the Michalovce district for both sexes: 3327.6 versus 1331.4 ng/g of lipid in males, 2751.8 versus 992.2 ng/g of lipid in females. Levels of DDE and DDT were also significantly higher, although the absolute differences were less pronounced. There was no substantial difference in HCB levels between the districts. We also conducted an ecologic study to compare cancer incidence occurring in these same two districts from 1985 through 1994. We calculated standardized incidence ratios (SIRs) and 95% confidence intervals for each district using indirect standardization and rates from eastern Slovakia. Among males from Michalovce (exposed), but not Svidnik (unexposed), there was an excess of cancer of the tongue (SIR=1.46; 1.06-1.96), stomach (SIR=1.15; 1.00-1.32), lung (SIR=1.14; 1.04-1.24), testis (SIR=1.40; 0.97-1.97), and kidney (SIR=1.23; 0.98-1.52), and lower than expected incidence of prostate cancer (SIR=0.83; 0.69-0.97); in contrast, there was an excess of peritoneal (SIR=3.05; 1.11-6.63) and laryngeal cancer (SIR=1.43; 0.99-1.98) in Svidnik not observed Michalovce. Among females from Michalovce, but not Svidnik, there was an excess of cancer of the lip (SIR=2.54; 1.53-3.96), stomach (SIR=1.22; 1.02-1.44), and lung (SIR=1.17; 0.94-1.45); in contrast, there was an excess of kidney (SIR=1.61; 1.03-2.40) and thyroid (SIR=1.97; 1.12-3.20) cancer in Svidnik not observed in Michalovce. Taken together, these results raise the possibility that high environmental exposure to organochlorines in the Michalovce district may be associated with higher rates of certain cancers, particularly stomach and lung cancer.     

Transformer oils as a potential source of environmental exposure to polychlorinated biphenyls (PCBs): an assessment in three central provinces of Iran

Environmental Science and Pollution Research - Polychlorinated biphenyl (PCB) contamination of oils from all transformers of the national electrical grid in Tehran, Qom, and Alborz, three central...     

Kinetic studies of endosulfan photochemical degradations by ultraviolet light irradiation in aqueous medium

Kinetic studies of endosulfan photochemical degradation in controlled aqueous systems were carried out by ultraviolet light irradiation at lambda = 254 nm. The photolysis of (alpha + beta: 2 + 1) endosulfan, alpha-endosulfan and beta-endosulfan were first-order kinetics. The observed rate constants obtained from linear least-squares analysis of the data were 1 x 10(-4) s(-1); 1 x 10(-4) s(-1); and 2 x 10(-5) s(-1), respectively, and the calculated quantum yields (phi) were 1, 1 and 1.6, respectively. Preliminary differential pulse polarographic (DPP) analysis allowed to observe the possible endosulfan photochemical degradation pathway. This degradation route involves the formation of the endosulfan diol, its transformation to endosulfan ether and finally the ether's complete degradation by observing the potential shifts.     

Kinetic studies of endosulfan photochemical degradations by ultraviolet light irradiation in aqueous medium

Kinetic studies of endosulfan photochemical degradation in controlled aqueous systems were carried out by ultraviolet light irradiation at λ = 254 nm. The photolysis of (α + β: 2 + 1) endosulfan, α-endosulfan and β-endosulfan were first-order kinetics. The observed rate constants obtained from linear least-squares analysis of the data were 1 × 10^?4 s^?1; 1 × 10^?4 s^?1; and 2 × 10^?5 s^?1, respectively, and the calculated quantum yields (φ) were 1, 1 and 1.6, respectively. Preliminary differential pulse polarographic (DPP) analysis allowed to observe the possible endosulfan photochemical degradation pathway. This degradation route involves the formation of the endosulfan diol, its transformation to endosulfan ether and finally the ether's complete degradation by observing the potential shifts.     

Cultivating Chlorella vulgaris and Scenedesmus quadricauda microalgae to degrade inorganic compounds and pesticides in water

Environmental Science and Pollution Research - This work evaluates the possibility of cultivating Scenedesmus quadricauda and Chlorella vulgaris microalgae in wastewater from the hydroponic...     

Environmental photochemistry of fluoroquinolones in soil and in aqueous soil suspensions under solar light

The photodegradation fate of widely used fluoroquinolone (FQ) drugs has been studied both at the water–soil interface and in soil at actual concentrations (500 ng g^?1) under natural solar light. Both human and veterinary drugs have been examined, namely ciprofloxacin, danofloxacin, enrofloxacin, levofloxacin, marbofloxacin and moxifloxacin. After spiking and irradiation, samples were submitted to microwave-assisted extraction and analyzed by high-performance liquid chromatography coupled to fluorescence detection (HPLC–FD). FQs degradation was faster in aqueous soil suspension than in neat soil (but lower than in “clean” water). A number of byproducts were identified by HPLC electrospray ionization tandem mass spectrometry after a post-extraction cleanup based on a molecularly imprinted polymer phase, for a more accurate detection. The distribution in the suspension was intermediate between those observed in soils and in aqueous solutions.     

Calculation of the relative influence of cloud layers on received ultraviolet and integrated solar radiation

Discrete ordinale radiative transfer calculations are used to examine the relative influence of cloud layers on the received ultraviolet flux and the received solar energy for a plane parallel atmosphere. The wavelength dependence for the cloud influence on the integrated solar radiation is primarily a function of the interaction of the cloud layer with the surrounding atmosphere and the underlying surface. It is found that for u.v. wavelengths greater than 300 nm, the ratio of u.v. to solar energy flux transmission through the atmosphere is insensitive to changes of cloud height, cloud scattering parameters and surface albedo (for realistic values), but is dependent on cloud thickness. For wavelengths approaching and less than 300 nm, absorption by tropospheric ozone results in sensitivity to cloud height and surface albedo     

Performance analysis of crushed gravel sand heat storage and biomass evaporator-assisted single slope solar still

Environmental Science and Pollution Research - In this research work, the productivity, energy, exergy, and economic and enviro-economic performance in crushed gravel sand heat storage and biomass...     

The toxicity of pyrene in the fish : Synergism by piperonyl butoxide and by ultraviolet light

A saturated solution of pyrene in water was not toxic to the fish , even in the presence of ultraviolet light. A survival curve possessing one minimum, and therefore defining two LC₅₀ values, was obtained when fish placed in water containing increasing amounts of a pyrene solution in dimethylsulfoxide were exposed to ultraviolet light after a short incubation period. The phototoxicity was linked to the presence of undissolved pyrene. A normal survival curve with only one LC₅₀ value was found when pyrene was solubilized with the surfactant Tween-20. Practically no phototoxicity was produced when the pyrene mixtures were filtered before use, or when a saturated aqueous solution of pyrene was used. Piperonyl butoxide, present at a concentration where it was not toxic, synergized the toxicity of pyrene . The environmental significance of this observation may be considerable.     

Individual PCBs as predictors for concentrations of non and mono-ortho PCBs in human milk

32 Dutch human milk samples were analyzed for PCBs with either HRGC-ECD or HRGC-LRMS in the NCI mode. Samples were collected from three different locations in The Netherlands: Amsterdam, Rotterdam and Groningen. Quantitatively, no differences could be observed between the three localities, while in addition the congener specific pattern showed a striking similarity for all individual samples. Only principal component analysis revealed slight individual differences. Based on similarities in the PCB profiles, linear relationships were calculated between 2,3′4,4′,5-PnCB (#118) or 2,2′4,4′5,5′HxCB (#153) and the most relevantnon andmonoortho PCBs exhibiting dioxinlike activity. These PCBs included 2,3,3′,4,4′-PnCB (#105), 3,3′,4,4′5-PnCB (#126) 2,3,3′,4,4′,5-HxCB (#156), 2,3,3′,4,4′,5′-HxCB (#157), 2,3′,4,4′,5,5′-HxCB (#167) and 3,3′,4,4′,5′5-HxCB (#169). Good linear relationships were observed between individual PCBs. Based on the results of this study, PCB #118 can be used to predict concentrations of the PCBs #105 and #126. PCB #153 can be used as a predictor for the PCBs #156, #157, #167 and #169, but also for the total toxic equivalencies (TEQs) ofnon andmonoortho PCBs present in human milk. This method using certain PCBs as predictors for other toxicological relevant congeners, can be useful and cost effective, e.g. for epidemiological studies. However, before applied a number of conditions should be met. These are:

1. A stable composition of the PCB matrix should be established.
2. A possible time dependent change in composition of the matrix should first be excluded when used over different time periods.

     

Isotope dilution analysis of polychlorinated biphenyls (PCBs) in transformer oil and global commercial PCB formulations by high resolution gas chromatography-high resolution mass spectrometry

Special polychlorinated biphenyls (PCBs) standards (native and isotope labeled) were analyzed by isotope dilution method using HRGC-HRMS. Multiple analysis of special PCBs standards by three different laboratories produced the relative response factors (RRFs) and relative standard deviations (RSDs %) was in the average of 0.979 and 3.86, respectively. Additionally, inter-laboratory analysis of various forms of transformer oil revealed the PCBs concentrations were in the following order; PCBs fortified transformer oil (940-1300 ng/g)>PCB polluted transformer oil (490-680 ng/g)>chemically degraded-transformer oil (480-490 ng/g) and PCBs free oil (ND-17 ng/g). Chemical degradation resulted in an order of magnitude decrease in the PCB concentrations. Specifically, higher chlorinated PCBs degraded into lower chlorinated PCBs. Also, composition of PCBs have been determined in PCB formulations from Japan (Kanechlor), Germany (Clophen), USA (Aroclor), Russia (Sovol) and Poland (Chlorofen). Major PCBs (24-PCB congeners) contributed 54-67%, 55-68%, 16-69%, 71% and 72% in Kanechlor, Clophen, Aroclor, Sovol and Chlorofen, respectively to total PCBs. The homologue pattern of Kanechlor, Aroclor and Clophen in technical fromulation was similar (e.g., Kanechlor-300 resembled to those of Clophen A-30 and Aroclor-1242). Furthermore, congener-specific distributions of major PCBs/dioxin-like PCBs and toxic equivalency quantities (TEQ) were calculated. Based on our tentative assumption calculations, cumulative production of five different technical PCB formulations, WHO-TEQ emission was estimated to be approximately 16.05 tons.