氧化石墨烯复合物对重金属废水中Ni~(2+)吸附效果的实验研究

正研究了氧化石墨烯复合物(MGO-SH)对含镍废水中Ni 2+的吸附性能。结果表明,MGO-SH吸附材料上有丰富的官能团,对Ni 2+有较强的吸附能力,去除率可达95%以上;较低Ni 2+初始质量浓度(≤25mg/L)下,吸附拟合结果与Freundlich吸附等温线模型较吻合;在采用该材料处理含Ni 2+工业废水时,应先将废水进行预处理,使Ni 2+低于25mg/L,再用MGO-SH吸附效果更佳。     

基于中心组合设计的电解预处理含酚废水工艺优化

针对含酚废水不宜直接进行生化处理的问题,采用电解法预处理含酚废水,通过中心组合设计优化初始p H、电压、极板间距、电解质浓度和苯酚初始浓度对苯酚去除率的影响。结果表明,5个因素的影响为电压电解质浓度极板间距初始p H苯酚初始浓度。优化后的最佳条件如下:初始p H为6.56、电压为24.93 V、极板间距为20.05 mm、电解质质量浓度为2.46 g/L、苯酚初始质量浓度为368.87 mg/L。在优化条件下,苯酚初始质量浓度为300.00~500.00 mg/L时,出水质量浓度计算值为12.60~51.60mg/L,实验值为17.40~55.40 mg/L,去除率计算值为89.68%~96.47%,实验值为88.90%~95.40%,计算值与实验值接近,说明模型可靠。     

铁酸锰纳米材料吸附含Ni~(2+)电镀废水的性能研究

采用非表面活性剂水热法制备了铁酸锰(MnFe2O4)纳米材料吸附剂,研究了吸附时间、溶液pH和温度对MnFe2O4纳米材料吸附模拟含Ni 2+电镀废水和实际含Ni 2+电镀废水中重金属Ni 2+的吸附性能,并探讨了该材料的再生利用性能。结果表明,MnFe2O4纳米材料可有效吸附电镀废水中的Ni 2+,吸附平衡时间为600min。对20mg/L的模拟含Ni 2+电镀废水,投加4.5mg的的MnFe2O4纳米材料进行吸附处理,Ni 2+的吸附去除率高达98%左右;实际工程应用中,应保持电镀废水偏碱性、温度25℃;MnFe2O4纳米材料具有理想的再生利用性能,重复吸附5次后,吸附去除率仍可达82.24%,在实际废水处理中具有广阔的应用前景。     

掺铁碳羟基磷灰石复合物对铅离子废水的吸附

采用废弃蛋壳和自制纳米Fe3O4为原材料,采用水热法制备Fe3O4/碳羟基磷灰石复合物(简称掺铁碳羟基磷灰石复合物,Fe-CHAP),将其用于吸附含Pb2+废水。通过BET比表面积、FTIR和XRD等表征手段对样品进行测试,分别探讨了影响吸附性能的主要因素,如pH、吸附剂用量、吸附时间、Pb2+初始浓度以及反应温度等。研究结果表明,在p H=5.0、0.03 g Fe-CHAP、150 mg/L Pb2+初始浓度、作用时间45 min和反应温度323 K等优化条件下,Fe-CHAP对Pb2+的去除率和吸附容量分别为98.59%和492.95mg/g。Langmuir等温模型较好地拟合了吸附实验数据,相关系数高达0.99,饱和吸附容量高达1 111.11 mg/g;准二级动力学模型较好地描述该吸附行为,相关系数高达0.999;热力学参数ΔG、ΔH和ΔS的计算值显示该吸附过程为自发吸热过程。     

粉煤灰负载铁离子催化氧化活性黄染料废水

以粉煤灰为载体,制备铁/粉煤灰负载型催化剂,并利用该催化剂催化H2O2氧化降解活性黄染料废水,探讨了H2O2投加量、催化剂投加量、染料初始浓度和初始pH值等因素对染料废水COD去除率和脱色率的影响。结果表明,当染料废水COD初始浓度为200 mg/L,初始pH值为1.7,投加0.5 g/100 mL催化剂及加入1.0 mL浓度为1.13 mol/L的H2O2溶液时,处理效果最好,此时染料废水的COD去除率和脱色率分别达到63%和99%,并且废水的可生化性得到很大的提高。利用该负载催化剂能够有效地减少活性黄染料废水中Fe3+的残留量。     

赤泥协同Fenton法处理焦化废水的研究

采用赤泥吸附协同Fenton法处理焦化废水,两者协同处理对COD的去除率高于其单独处理之和.考察了赤泥投加量、初始pH值、反应温度、H2O2浓度和Fe2+浓度等因素对降解效果的影响,实验结果表明,在20 g/L的赤泥、初始pH=3、80 mmol/L的H2O2、224 mg/L的Fe2+的最佳条件下,经过120 min...     

Fenton氧化-混凝联合工艺处理络合铜镍废水的研究

采用Fenton试剂氧化-混凝联合工艺对难处理络合铜镍电镀废水进行了研究,考察了废水初始pH值、H2O2初始浓度、[Fe2 ]/[H2O2]、反应时间和温度、混凝液pH、混凝剂质量浓度对处理过程的影响,探讨了废水的降解途径和机理.结果表明,在体系初始pH=4,温度30℃,H2O2投加量为800mg/L,[Fe2 ]/[H2O2]=0.1,反应时间60 min,混凝液pH=8及混凝剂质量浓度为500mg/L的条件下,废水的COD去除率为96.98%,Cu2 为99.91%,Ni2 为99.92%,处理水完全达到国家一级排放标准.同时依据GC/MS对X-GN降解最终产物的分析结果,推导出废水的基本降解机理和途径.     

RPB-O3/H2O2法处理硝基苯模拟废水

在超重力场中,研究了硝基苯模拟废水的臭氧/双氧水(O3/H2O2)法处理效果,考察了超重力因子β、H2O2浓度、初始p H、液体流量及处理时间等因素对硝基苯去除率的影响。结果表明,硝基苯去除率随超重力因子β和处理时间的增加而增大,而随H2O2浓度、初始p H和液体流量的增加呈先增大后降低的趋势。当硝基苯初始浓度300 mg/L,工艺条件β=80、p H=10.0、臭氧质量浓度约为40 mg/L、H2O2浓度为4.9 mmol/L、液体流量为120 L/h时,循环处理35 min硝基苯去除率可达96.7%。处理时间60 min后,废水中硝基苯含量1.4 mg/L,COD为39 mg/L,达国家一级排放标准(GB 8978-1996)。在此条件下,硝基苯的降解过程符合准一级反应动力学。     

铁粉还原-Fenton氧化处理络合铜废水的研究

采用铁粉还原-Fenton氧化工艺处理含络合铜工业废水,研究了联合工艺对络合铜的破络效果,重点考察了常温下H2O2投加量、初始pH值、反应时间、Cu(Ⅱ)初始浓度以及铁粉粒径等因素对该工艺处理效果的影响,同时探讨了相关机理。结果表明:在初始Cu(Ⅱ)浓度为50 mg/L,初始pH=3的体系中,加入过量铁粉,H2O2投加量控制在H2O2∶COD=1.5∶1(质量比),反应30 min后在pH=9的条件下沉淀,废水的COD去除率为86.5%,Cu(Ⅱ)去除率为99.9%,处理水达到《电镀污染物排放标准》(GB21900-2008)要求。研究还表明:铁粉粒径对处理效率的影响较小,采用工业级铁粉即可达到理想效果。     

超声波/Fenton处理含酚废水的影响因素

实验研究主要影响因素对超声波/Fenton试剂处理苯酚废水效果的影响,确定工艺参数。以人工配制的模拟苯酚废水为实验水样,通过静态实验研究p H值、Fe SO4·7H2O投加量、H2O2投加量和超声时间对苯酚和COD去除率的影响。研究结果表明,对于苯酚浓度为200 mg/L,COD为476.6 mg/L苯酚废水,在实验用水量为1 000 m L,p H值为6,Fe SO4·7H2O投加量为800 mg/L,H2O2投加量为Qth,超声时间为30 min的条件下,苯酚去除率可达到92.27%,COD去除率可达到82.48%,处理后苯酚浓度为14.80 mg/L,COD为83.50 mg/L。p H值、Fe SO4·7H2O投加量、H2O2投加量和超声时间对超声/Fenton工艺处理苯酚废水均有较显著地影响,工程应用时应给予足够的重视。     

Optimization of Height of Release of Air Pollutants

A number of key projects in the Environmental Protection Agency (EPA) particulate R&;D program having applicability to industry are presented. For electrostatic precipitators (ESP) there is presented the result of work on large diameter discharge electrodes which provide a decrease in penetration of up to a factor of 4 when compared to conventional small diameter electrodes. Also discussed is the multistage ESP which provides a collection efficiency that would require a collecting plate area 4 or 5 times larger with conventional ESP technology. The E-SOX technology makes use of the multistage concept to free up space in the ESP for SO₂ removals of up to 90%. Electrostatically augmented fabric filtration provides a reduction in pressure drop of about 5 0% as compared to conventional fabric filtration. Wind tunnel modeling of windbreaks for material storage piles indicates a potential for providing engineering design data that would allow significant emission reduction caused by wind erosion     

Investigation of the characteristics of the reflectivity of clouds

This paper investigates some of the reflectivity characteristics that clouds (when modelled as solid bodies) must exhibit to be compatible with observations that the reflecting surface of a cloud (i) appears almost equally bright across its face, (ii) is brightest when the cloud is opposite to the Sun but decreases in brightness as the cloud moves to other positions and (iii) increases in brightness with increasing optical thickness of the cloud in the observer's line of sight. These observations, respectively, are shown to imply that the peak value of the bidirectional total reflectivity from a cloud surface (i) increases in inverse proportion to the cosine of the angle between the Sun and the normal to the cloud surface, as the incident angle increases, (ii) appears to be directed back in the direction of the incident radiation, and (iii) increases as optical thickness of the cloud in the observer's line of sight increases. The results could have application in many fields (e.g. modelling diffuse radiance distributions for cloudy skies).     

实验室质量管理体系内部审核的实施

在实施ISO／IEC17025：1999标准《检测和校准实验室能力的通用要求》过程中，通过实验室质量管理体系内部审核的实践与系统分析，识别出内部审核实施阶段的关键环节，提出召开首次会议、收集审核证据、确定审核发现和召开末次会议的技术方法，对提高内部审核的质量和有效性、获得可靠的审核结论具有重要意义。     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

扬中生态环境建设的思考与实践

结合扬中生态环境的基本情况和存在的不足，进行了具体分析，对扬中未来生态建设的发展方向提出了建议及实施措施。     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

Comparison of methods for evaluation of activity of photocatalytic films

Objective

This work aims to investigate the correlation between the photocatalytic activity determined by methylene blue bleaching (DIN 52980), stearic acid degradation, and degradation of acetone in gas phase.

Method

The photocatalytic TiO₂ coatings included in this investigation ranged from thin commercially available coatings (Activ^TM and BioClean^TM) and ready to use suspensions (Nano-X PK1245) to lab-produced PVD and sol?Cgel coatings. XRD analysis of the photocatalytic coatings showed that all the coatings consisted of nanocrystalline anatase, although the thickness and porosity varied considerably.

Results

The study showed that the reproducibility of the activity measurements was good. However, more importantly, the investigation showed that there is a good correlation between the activities determined by the different methods even though the characteristics of the photocatalytic coatings and the organic probe molecules varied considerably.

Conclusion

The overall findings of this work suggest that there is a good correlation between the investigated methods. These results are promising for the future work concerning standardization of methods for determination of the activity of photocatalytic films.     

Impact of overexploitation of shellfish: northeastern coast of India

India has a very extensive coastline of about 7515 km, rich in diverse living resources. These resources continue to deteriorate with rampant harvesting or are altered for other uses such as aquaculture and fisheries. The present paper deals with degrading coastal habitats in northeastern India, and projects the intensity of the stress arising from the collection of tiger prawn seeds (Penaeus monodon) for aquacultural farms and molluskan shells for poultry feed and edible lime. Indiscriminate exploitation of these resources leads to a heavy reduction of the species concerned and other associated marine communities. The magnitude of such destruction has been quantified. The impacts of biodiversity loss and their after-effects on the ecobalance of this coastal system have become a matter of great concern to ecologists to maintain security and sustainability. The authors propose a public awareness program on themes relating to the importance of biodiversity for human livelihoods.