聚合物强化超滤处理含铜废水

聚合物强化超滤工艺（PEUF）是一种将高分子聚合物和超滤技术结合的新型、高效的重金属废水治理方法。以壳聚糖（CTS）为聚合物去除水中的铜离子。考察了吸附络合和超滤过程中影响铜去除率的多种因素。结果表明,溶液pH值为6.0、CTS浓度为0.15 g/L和反应时间为60 min时,通过超滤系统后效果最佳。装载比一定时,铜初始浓度的变化对铜的去除率没有明显影响。CTS对铜的吸附过程符合Langmuir吸附等温方程。还研究了超滤膜的污染情况和膜清洗方法,结果表明,酸清洗效果较好,可使膜通量恢复达87%左右。     

电絮凝─超滤协同去除水中的腐殖酸

采用电絮凝-超滤(electrocoagulation-ultrafiltration,EC-UF)技术协同去除水中腐殖酸(HA),主要考察了电流密度、初始pH、初始HA浓度、初始电导率等因素对HA去除率的影响,解析了在这些影响因素下HA的去除机理,并对滤饼层特征和膜污染机制进行了研究。结果表明,在电流密度j=10 A·m~(-2)、初始pH=7、初始电导率σ0=1 000μS·cm~(-1)、电解时间为15 min的条件下,初始HA浓度为10 mg·L~(-1)时,EC-UF工艺对水中的HA的去除率可以达到97.3%,膜污染为可逆污染,被污染的膜经过清洗后通量可恢复到初始的94%。     

TiO2光催化复合分离膜对水中天然有机物的去除

在水源污染越来越严重、水质标准日益严格的背景下,超滤（UF）已逐渐成为替代饮用水常规处理技术的最佳选择之一。本研究中采用相转化法,将聚偏氟乙烯（PVDF）、聚乙二醇（PEG）和二氧化钛（TiO2）共混制得光催化复合分离膜并对其进行扫描电子显微镜（SEM）、原子力显微镜（AFM）和X射线能谱仪（EDS）等相应的表征。比较了有无光照条件下,PVDF-PEG和PVDF—PEG—TiO2膜对腐殖酸（HA）的截留和超滤过程中的膜污染情况。研究结果表明,TiO2光催化复合分离膜能提高对水中天然有机物的去除并同时降低膜污染。紫外光照强度越强,PVDF-PEG—TiO2膜的抗污染性能越好。另外,光催化能更有效地减少超滤初始浓度较低的腐殖酸溶液过程中的膜通量衰减。     

pH值、离子强度和重金属离子对腐殖酸紫外谱图的影响

研究pH值、溶液离子强度和金属离子对腐殖酸紫外光谱的影响,分析腐殖酸的结构特征,探讨E3/E4与pH值和溶液离子强度的关系。结果表明,腐殖酸的紫外光谱吸收带,随pH值增大主要发生蓝移。但随溶液离子强度增大,pH值对腐殖酸紫外吸收带的影响逐渐降低直至不影响。随溶液离子强度增大,腐殖酸的紫外光谱吸收带都发生红移、吸收强度增大。且腐殖酸的E3/E4值与溶液离子强度具有显著的正相关性。腐殖酸的紫外光谱中的吸收带,随投加Cu2+或Cd2+浓度增大而发生红移。     

TiO2光催化复合分离膜对水中天然有机物的去除

在水源污染越来越严重、水质标准日益严格的背景下,超滤(UF)已逐渐成为替代饮用水常规处理技术的最佳选择之一。本研究中采用相转化法,将聚偏氟乙烯(PVDF)、聚乙二醇(PEG)和二氧化钛(TiO₂)共混制得光催化复合分离膜并对其进行扫描电子显微镜(SEM)、原子力显微镜(AFM)和X射线能谱仪(EDS)等相应的表征。比较了有无光照条件下,PVDF-PEG和PVDF-PEG-TiO₂膜对腐殖酸(HA)的截留和超滤过程中的膜污染情况。研究结果表明,TiO₂光催化复合分离膜能提高对水中天然有机物的去除并同时降低膜污染。紫外光照强度越强,PVDF-PEG-TiO₂膜的抗污染性能越好。另外,光催化能更有效地减少超滤初始浓度较低的腐殖酸溶液过程中的膜通量衰减。     

基于Donnan渗析离子交换膜分离水中的Cd (Ⅱ)

基于Donnan渗析原理构建了离子交换膜反应器,探讨了受体池溶液种类和浓度、给体和受体池搅拌功率以及给体池溶液的初始pH、进水流量和Cd(Ⅱ)进水浓度等因素对Cd(Ⅱ)分离效果的影响。结果表明,随着搅拌功率由0.035W增大为0.162 W,Cd(Ⅱ)分离去除率与离子通量显著增加。当受体液NaCl浓度为0～0.5 mol·L-1时,Cd(Ⅱ)分离去除率随着受体液浓度的增加而显著增加。当给体池进水Cd(Ⅱ)溶液初始pH≤8时,Cd(Ⅱ)分离去除率随受体液pH的增加而增加。此外,给体池中Cd(Ⅱ)分离去除率与Cd(Ⅱ)初始浓度以及给体池进水流量成反比。在本实验条件下,Cd(Ⅱ)的分离去除率最高可达85.51%。     

盐类对模拟胞外聚合物(EPS)膜污染的影响

实验旨在研究盐类对模拟胞外聚合物(EPS)溶液在超滤和微滤过程中膜污染影响,通过添加与无添加盐类的模拟溶液的比较,研究盐类对EPS膜过滤在死端过滤过程的影响。实验考察了不同模拟溶液的膜通量衰减情况和滤饼比阻,并利用Hermia模型对实验数据进行拟合分析验证膜污染机理。实验结果表明,在超滤过程中,Ca2+和Al3+能在一定程度上提高膜通量,降低滤饼比阻,延缓膜污染;在微滤过程中,两者的添加反而降低了初始通量,添加Ca2+后滤饼比阻值反而有所增大;Na+对超/微滤过程影响很小。通过Hermia模型拟合分析发现,在超滤过程中,添加盐和无添加的溶液均以滤饼堵塞机理为主,而在微滤过程中则是以中间堵塞和滤饼堵塞机理为主。     

酒石酸钾钠(PST)对纳滤处理重金属废水的强化效果

以酒石酸钾钠(PST)为络合剂,分别选取Cd、Zn、As和Pb 4种金属废水,探索络合纳滤工艺对金属离子去除率和膜通量的强化效果,测定纳滤膜表面接触角以表征膜通量变化规律,并研究了压力、金属浓度和溶液pH参数对络合纳滤过程的影响。结果表明,PST对4种金属去除的强化效果存在相似规律,分别有一个最佳PST添加浓度。随PST浓度的增加,金属离子去除率先增大后减小,而膜通量一直增大。研究发现,纳滤膜表面接触角与膜通量呈稳定的反比例关系,与金属离子种类和PST添加量无关。随着操作压力的增大,膜通量线性增加,去除率基本不变;金属离子浓度的增加对膜通量影响不大,金属去除率略有上升;pH在4~5之间变化时,As去除中膜通量和去除率均有所升高,而Cd、Zn和Pb 3种溶液处理效果基本不受pH影响。     

酒石酸钾钠（PST）对纳滤处理重金属废水的强化效果

以酒石酸钾钠（PsT）为络合剂,分别选取cd、zn、As和Ph4种金属废水,探索络合纳滤工艺对金属离子去除率和膜通量的强化效果,测定纳滤膜表面接触角以表征膜通量变化规律,并研究了压力、金属浓度和溶液pH参数对络合纳滤过程的影响。结果表明,PsT对4种金属去除的强化效果存在相似规律,分别有一个最佳PsT添加浓度。随PsT浓度的增加,金属离子去除率先增大后减小,而膜通量一直增大。研究发现,纳滤膜表面接触角与膜通量呈稳定的反比例关系,与金属离子种类和PsT添加量无关。随着操作压力的增大,膜通量线性增加,去除率基本不变;金属离子浓度的增加对膜通量影响不大,金属去除率略有上升;pH在4～5之间变化时,As去除中膜通量和去除率均有所升高,而cd、zn和Ph3种溶液处理效果基本不受pH影响。     

荷负电超滤膜同时去除水中天然有机物和铅离子

通过特定的化学反应对截留分子量为30 k D的再生纤维素(RC)超滤膜进行改性,得到荷负电超滤膜,并研究了其表面荷电性能。选用腐殖酸作为天然有机物的代表物质,研究荷负电改性膜同时去除溶液中腐殖酸和铅离子,主要考察了p H值和腐殖酸铅离子络合作用对两者截留率的影响,并对比了荷负电膜和未改性膜去除天然有机物和铅离子的研究结果。得到如下结论:(1)在酸性及中性溶液环境下,随着p H值的升高,荷负电超滤膜对腐殖酸和铅离子的截留率都提高。(2)铅离子与腐殖酸共存时,腐殖酸铅离子络合体的荷负电性相比于原腐殖酸分子降低,荷负电超滤膜对混合溶液中腐殖酸的截留率有一定程度降低,络合在腐殖酸表面的铅离子随着腐殖酸的截留而被截留,铅离子截留率得到一定程度提升。(3)由于腐殖酸与铅离子络合体带负电,其与荷负电膜之间存在静电作用,所以荷负电改性膜对腐殖酸和铅离子的截留率比未改性中性膜高。     

Optimization of Height of Release of Air Pollutants

A number of key projects in the Environmental Protection Agency (EPA) particulate R&;D program having applicability to industry are presented. For electrostatic precipitators (ESP) there is presented the result of work on large diameter discharge electrodes which provide a decrease in penetration of up to a factor of 4 when compared to conventional small diameter electrodes. Also discussed is the multistage ESP which provides a collection efficiency that would require a collecting plate area 4 or 5 times larger with conventional ESP technology. The E-SOX technology makes use of the multistage concept to free up space in the ESP for SO₂ removals of up to 90%. Electrostatically augmented fabric filtration provides a reduction in pressure drop of about 5 0% as compared to conventional fabric filtration. Wind tunnel modeling of windbreaks for material storage piles indicates a potential for providing engineering design data that would allow significant emission reduction caused by wind erosion     

Investigation of the characteristics of the reflectivity of clouds

This paper investigates some of the reflectivity characteristics that clouds (when modelled as solid bodies) must exhibit to be compatible with observations that the reflecting surface of a cloud (i) appears almost equally bright across its face, (ii) is brightest when the cloud is opposite to the Sun but decreases in brightness as the cloud moves to other positions and (iii) increases in brightness with increasing optical thickness of the cloud in the observer's line of sight. These observations, respectively, are shown to imply that the peak value of the bidirectional total reflectivity from a cloud surface (i) increases in inverse proportion to the cosine of the angle between the Sun and the normal to the cloud surface, as the incident angle increases, (ii) appears to be directed back in the direction of the incident radiation, and (iii) increases as optical thickness of the cloud in the observer's line of sight increases. The results could have application in many fields (e.g. modelling diffuse radiance distributions for cloudy skies).     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

扬中生态环境建设的思考与实践

结合扬中生态环境的基本情况和存在的不足，进行了具体分析，对扬中未来生态建设的发展方向提出了建议及实施措施。     

实验室质量管理体系内部审核的实施

在实施ISO／IEC17025：1999标准《检测和校准实验室能力的通用要求》过程中，通过实验室质量管理体系内部审核的实践与系统分析，识别出内部审核实施阶段的关键环节，提出召开首次会议、收集审核证据、确定审核发现和召开末次会议的技术方法，对提高内部审核的质量和有效性、获得可靠的审核结论具有重要意义。     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

有机官能团对改性硅吸附微囊藻毒素的影响

考察了不同有机改性硅对微囊藻毒素LR(mLR)和LA(mLA)的等温吸附行为。结果表明,有机改性硅可有效吸附去除水体中<0.1×10-6(质量分数)的微囊藻毒素,并且吸附去除效果随表面改性官能团中碳原子数量的增加而增加;相同条件下,有机改性硅在微囊藻毒素异构体之间存在着一定的吸附选择性。     

生物质快速热裂解主要参数对生物油产率的影响

以松木木屑为原料,在自制的小型流化床上,开展了生物质热裂解温度、生物质粒径和进料速率对生物油产率的影响实验研究.结果表明,在热裂解温度分别为450、475、500、525和550℃条件下,当热裂解温度为500℃时,生物油产率最高,平均产率达到53.33%(质量百分比).反应温度越高,炭产量越低,不可冷凝气体产量越高,气体发热值越高;粒径＜1 mm的生物质其粒径对生物油产率影响不大;生物质进料速率增加时,生物油产率增加.本研究为生物能的利用提供了新的途径.