Sensitivity analysis of ground-level ozone concentration to emission changes in two urban regions of southeast Texas

Air pollutant emission is one of the predominant factors affecting urban air quality such as ground-level ozone formation. This paper assesses the impact of changing emission inventory scenarios, based on combinations of point, mobile, area/non-road and biogenic sources, on the tropospheric ozone concentration in two southeast Texas urban areas, i.e. Houston-Galveston and Beaumont-Port Arthur, during the rapid ozone formation event (ROFE) on August 25, 2000. The EPA's Community Multiscale Air Quality (CMAQ) modeling system with 1999 national emission inventory (NEI99) estimates and updated SAPRC99 chemical mechanism are used in the sensitivity analysis for twelve different emission scenarios. Based on model results, it is found that the point source emission of NOx and VOC contributes the greatest ozone peak in the ROFE. Removing Texas point sources of VOC and NOx emission from the inventory results in a reduction in peak O3 concentration by 128 and 70 ppbv in Houston urban area, respectively. Similar but less drastic impact from point source is also observed in the Beaumont-Port Arthur area. The effect on peak ozone concentration due to mobile, area and non-road sources emissions are less significant compared to that of point source emission. Reducing VOC emission appears to be more effective than reducing NOx emission in lowering peak O3 concentration in the studied region. Although biogenic emission can contribute up to 37 ppbv of peak ozone level over a large area, the affected area is away from the urban region of concern, and should not be the main cause for O3 non-attainment in the two urban areas. Removing CO emission from mobile sources does not lead to significant reduction (< 1 ppbv) in ozone concentrations. The modeled data also show that the transport of O3 precursors from adjacent states can cause a significant ozone plume near Beaumont due to its proximity to the state border based on the conditions during the August 25, 2000 O3 episode.     

Emergy evaluation of an integrated livestock wastewater treatment system

Wastewater treatment practices should pay more attention to their environmental performances due to their resources consumption and emissions’ impact. While reclaimed water reuse seems to have become a promising practice, is it always feasible in any condition? To address this issue, this study carried out an extended emergy evaluation of a holistic wastewater treatment system. On one hand, this method was extended to include the emissions’ impact. On the other hand, this study integrated a wastewater treatment plant, its excess sludge disposal system and treated water disposal system into an integrated wastewater treatment system (IWTS), so as to evaluate its performances more completely. And then several indicators, including cost per unit pollutant eliminated (CUPE), ratio of positive output (RPO), environmental load ratio (ELR), and sustainability index (SI), were proposed for evaluating the performances of an IWTS. Two scenarios (scenario A: wastewater treatment + sludge landfilling + treated water discharges; scenario B: wastewater treatment + sludge landfilling + reclaimed water reuse) for a livestock wastewater treatment plant in Sichuan Agricultural University located in Ya’an City in Southwest China, as cases, were researched. The results show that scenario B has lower positive output efficiency and greater environmental load than scenario A. Meanwhile, the reclaimed water reuse raises cost per unit pollutant eliminated compared with the treated water being discharged directly; emissions’ impact enhances the environmental load of the two scenarios to different degree; emissions’ impact has decisive effect on the sustainability of the two scenarios. These results mean that the reclaimed water reuse should not be advocated in this case. This study provides some policy implications: (1) wastewater treatment process should be comprehensively evaluated from its resources consumption and impact of emissions; (2) reclaimed water reuse should be carefully evaluated from its pros and cons simultaneously; (3) the local conditions should be considered when implementing reclaimed water reuse, such as local water body conditions, market demands, the related laws and regulations, corporations’ economic conditions, etc.     

Impacts of urban forests on offsetting carbon emissions from industrial energy use in Hangzhou,China

This study quantified carbon storage and sequestration by urban forests and carbon emissions from energy consumption by several industrial sources in Hangzhou, China. Carbon (C) storage and sequestration were quantified using urban forest inventory data and by applying volume-derived biomass equations and other models relating net primary productivity (NPP) and mean annual biomass increments. Industrial energy use C emissions were estimated by accounting for fossil fuel use and assigning C emission factors. Total C storage by Hangzhou's urban forests was estimated at 11.74 Tg C, and C storage per hectare was 30.25 t C. Carbon sequestration by urban forests was 1,328, 166.55 t C/year, and C sequestration per ha was 1.66 t C/ha/year. Carbon emissions from industrial energy use in Hangzhou were 7 Tg C/year. Urban forests, through sequestration, annually offset 18.57% of the amount of carbon emitted by industrial enterprises, and store an amount of C equivalent to 1.75 times the amount of annual C emitted by industrial energy uses within the city. Management practices for improving Hangzhou's urban forests function of offsetting C emissions from energy consumption are explored. These results can be used to evaluate the urban forests' role in reducing atmospheric carbon dioxide.     

Environmental consequences of recycling aluminum old scrap in a global market

Nowadays, aluminum scrap is traded globally. This has increased the need to analyze the flows of aluminum scrap, as well as to determine the environmental consequences from aluminum recycling. The objective of this work is to determine the greenhouse gases (GHG) emissions of the old scrap collected and sorted for recycling, considering the market interactions. The study focused on Spain as a representative country for Europe. We integrate material flow analysis (MFA) with consequential life cycle assessment (CLCA) in order to determine the most likely destination for the old scrap and the most likely corresponding process affected. Based on this analysis, it is possible to project some scenarios and to quantify the GHG emissions (generated and avoided) associated with old scrap recycling within a global market. From the MFA results, we projected that the Spanish demand for aluminum products will be met mainly with an increase in primary aluminum imports, and the excess of old scrap not used in Spain will be exported in future years, mainly to Asia. Depending on the scenario and on the marginal source of primary aluminum considered, the GHG emission estimates varied between −18,140 kg of CO₂ eq. t⁻¹ and −8427 of CO₂ eq. t⁻¹ of old scrap collected. More GHG emissions are avoided with an increase in export flows, but the export of old scrap should be considered as the loss of a key resource, and in the long term, it will also affect the semifinished products industry. Mapping the flows of raw materials and waste, as well as quantifying the GHG impacts derived from recycling, has become an essential prerequisite to consistent development from a linear toward a circular economy (CE).     

Worst case scenario study to assess the environmental impact of amine emissions from a CO2 capture plant

Use of amines is one of the leading technologies for post-combustion carbon dioxide capture from gas and coal-fired power plants. This study assesses the potential environmental impact of emissions to air that result from use of monoethanol amine (MEA) as an absorption solvent for the capture of carbon dioxide (CO₂). Depending on operation conditions and installed reduction technology, emissions of MEA to the air due to solvent volatility losses are expected to be in the range of 0.01–0.8 kg/tonne CO₂ captured. Literature data for human and environmental toxicity, together with atmospheric dispersion model calculations, were used to derive maximum tolerable emissions of amines from CO₂ capture. To reflect operating conditions with typical and with elevated emissions, we defined a scenario MEA-LOW, with emissions of 40 t/year MEA and 5 t/year diethyl amine (DEYA), and a scenario MEA-HIGH, with emissions of 80 t/year MEA and 15 t/year DEYA. Maximum MEA deposition fluxes would exceed toxicity limits for aquatic organisms by about a factor of 3–7 depending on the scenario. Due to the formation of nitrosamines and nitramines, the estimated emissions of DEYA are close to or exceed safety limits for drinking water and aquatic ecosystems. The “worst case” scenario approach to determine maximum tolerable emissions of MEA and other amines is in particular useful when both expected environmental loads and the toxic effects are associated with high uncertainties.     

Energy and CO2 from high performance recycled aggregate production

The use of recycled concrete aggregates (RCA) in applications other than road sub-layers is limited by two factors: the high porosity of RCA in comparison with natural aggregates, and the restrictions set forth in standards and building codes. Research efforts aimed at alleviating these restrictions are focused on improving the quality of coarse RCAs by reducing the amount of adhered cement pastes, which is the weakest element in this system and influences the rheological behaviour.This paper presents an analysis of the environmental impacts of the recent mechanical and thermo-mechanical processing techniques which produce high performance RCA by reducing the volume of adhered cement paste. Based on published data, processing scenarios were established. These scenarios permit making rough estimates of energy consumption, CO₂ emissions, fines generation and product quality. Using these data and the available emission factors from several countries, an objective comparison was made between these innovating processes and conventional recycling.The production of fines increases from 40% up to as much as 70% as the volume of adhered cement paste on the RCA is reduced. Fuel fed thermo-mechanical process energy consumption, per tonne of recycled aggregate, varies between 36 and 62 times higher than conventional recycling processes. Mechanical processing, combined with microwave heating, increases energy consumption from 3 to a little more than 4 times conventional recycling. Consequently, CO₂ emissions released by conventional coarse aggregate production go from 1.5 to 4.5 kgCO₂/t, to around 200 kgCO₂/t, for that of fossil fuel fed thermo-mechanical treatments.Mechanical and mechanical/microwave treatments appear to have the greatest environmental potential. Notwithstanding, the further development of markets for fines is crucial for reducing environmental loads.     

Environmental benefits from the use of the residual biomass in nurseries

Every year, nurseries waste about 40 t of residual biomass for each ha of potted plants cultivation. The European nursery sector deals with about 90,000 ha of cultivated land and 120,000 ha of nurseries, with a turnover of 19.8 billion Euros in 2011. In recent years, a number of Italian projects highlighted that GHG (greenhouse gas) emissions for the nursery sector range between 37 tCO₂eq/ha/year and 45 tCO₂eq/ha/year for potted plants, mainly due to the consumption of electric energy, plastics and peat. Moreover, other studies analyse the impacts associated to nurseries, recommending best practices for energy reductions and waste recycle or reuse. Therefore, the present work focused its attention to the possible environmental benefits associated to the reuse of residues (wood and substrate) of potted plants that are discarded from the nursery production chain. GHG emissions and fossil energy requirement were quantified by considering the CO₂eq (CO₂ equivalent) and the CER (cumulative energy requirement) respectively, in order to assess the environmental impacts of two different scenarios proposed for the materials recovery. Final results highlighted that the solutions which are able to recover the substrate and the wood allow impact reductions compared to landfill disposal. In particular, the scenario consisting in the immediate separation of the substrate from the root-plant system and the successive chipping of wood for energetic reuse, allows higher savings than those obtainable through shredding and subsequent wind separation. Moreover, for what concerns the CO₂eq, an adequate use of the residual biomass make it possible to compensate the GHG emissions of the nurseries up to 15%.     

A comparative study of US EPA 1996 and 1999 emission inventories in the west Gulf of Mexico coast region, USA

Emission inventory is one of the required inputs to air quality models. To assist in the urban and regional modeling efforts, United States Environmental Protection Agency (EPA) has compiled a National Emission Inventory (NEI) for criterion pollutants, and the precursors of ozone and particulate matter (PM). In December 2002, EPA released the 1999 NEI estimates (NEI99), which represent the most recent national emission data. However, the data sets are not in model-ready format for air quality simulations. This present work converts the NEI99 Final Version 2 data sets into Inventory Data Analyzer (IDA) format and processes the data using the Sparse Matrix Operator Kernel Emissions (SMOKE) modeling system to generate a gridded emission inventory in a domain covering the west Gulf Coast Region, USA. The spatial and diurnal emission characteristics of the gridded emission inventories are then assessed and compared with those of the National Emission Trend 1996 (NET96). The NEI99 database contains more complete emission records in both area and point sources. It is also found that NEI99 data exhibit greater emissions with respect to point and mobile sources but smaller emissions with respect to area sources when compared to the corresponding gridded NET96 data in the same study domain. The most distinct differences between the NEI99 and NET96 databases are CO emission of mobile sources, SO2 emissions of point sources, and VOC/PM/NH3/NOx emissions of area and non-road sources. The gridded NEI99 data show low VOC/NOx ratios (<2-5) in the urban areas of the study domain.     

Energy and carbon dioxide intensity of Thailand's steel industry and greenhouse gas emission projection toward the year 2050

The purpose of this article is to study the energy and carbon dioxide intensities of Thailand's steel industry and to propose greenhouse gas emission trends from the year 2011 to 2050 under plausible scenarios. The amount of CO₂ emission from iron and steel production was calculated using the 2006 Intergovernmental Panel on Climate Change (IPCC) guidelines in the boundary of production process (gate to gate). The results showed that energy intensity of semi-finished steel product was 2.84 GJ/t semi-finished steel and CO₂ intensity was 0.37 tCO_2eq/t semi-finished steel. Energy intensity of steel finishing process was 1.86 GJ/t finished steel and CO₂ intensity was 0.16 tCO_2eq/t finished steel. Using three plausible scenarios from Thailand's steel industry, S1: without integrated steel plant (baseline scenario), S2: with a traditional integrated BF–BOF route and S3: with an alternative integrated DR-EAF route; the Greenhouse Gas emissions from the year 2011 to 2050 were projected. In 2050, the CO₂ emission from S1 (baseline scenario) was 4.84 million tonnes, S2 was 21.96 million tonnes increasing 4.54 times from baseline scenario. The CO₂ emission from S3 was 7.12 million tonnes increasing 1.47 times from baseline scenario.     

The potential contribution of sustainable waste management to energy use and greenhouse gas emission reduction in the Netherlands

Future limitations on the availability of selected resources stress the need for increased material efficiency. In addition, in a climate-constrained world the impact of resource use on greenhouse gas emissions should be minimized. Waste management is key to achieve sustainable resource management. Ways to use resources more efficiently include prevention of waste, reuse of products and materials, and recycling of materials, while incineration and anaerobic digestion may recover part of the embodied energy of materials. This study used iWaste, a simulation model, to investigate the extent to which savings in energy consumption and CO₂ emissions can be achieved in the Netherlands through recycling of waste streams versus waste incineration, and to assess the extent to which this potential is reflected in the LAP2 (currently initiated policy). Three waste streams (i.e. household waste, bulky household waste, and construction and demolition waste) and three scenarios compare current policy to scenarios that focus on high-quality recycling (Recycling+) or incineration with increased efficiency (Incineration+). The results show that aiming for more and high-quality recycling can result in emission reductions of 2.3 MtCO₂ annually in the Netherlands compared to the reference situation in 2008. The main contributors to this reduction potential are found in optimizing the recycling of plastics (PET, PE and PP), textiles, paper, and organic waste. A scenario assuming a higher energy conversion efficiency of the incinerator treating the residual waste stream, achieves an emission reduction equivalent to only one third (0.7 MtCO₂/year) of the reduction achieved in the Recycling+ scenario. Furthermore, the results of the study show that currently initiated policy only partially realizes the full potential identified. A focus on highest quality use of recovered materials is essential to realize the full potential energy and CO₂ emission reduction identified for the Netherlands. Detailed economic and technical analyses of high quality recycling are recommended to further evaluate viable integrated waste management policies.     

Greenhouse gas emissions and energy balance of sunflower biodiesel: Identification of its key factors in the supply chain

The production of first generation biofuels, such as sunflower-based biodiesel, is potentially an option for diversifying the energy matrix in several South American countries. However, biofuels present environmental challenges, especially concerning the reduction of greenhouse gas (GHG) emissions. This study, using a life-cycle approach, evaluates the GHG emissions and energy balance of the future nationwide production of sunflower-based biodiesel in Chile. Direct land use change is included in the analysis. The overall findings indicate that sunflower biodiesel, under the most likely production conditions, will have better environmental performance than fossil diesel in terms of both indicators. The agricultural stage is associated to key factors such as land use change, and nitrogen fertilizers. These factors contribute significantly to GHG emissions or energy demand in the biodiesel life cycle. The sensitivity analysis shows that no GHG emission saving could occur if nitrogen fertilizers rate exceeds 330 kg N/ha. In order to reduce the environmental impacts of this biofuel, improvement measures are suggested.     

Life cycle assessment of natural gas combined cycle power plant with post-combustion carbon capture,transport and storage

Hybrid life cycle assessment has been used to assess the environmental impacts of natural gas combined cycle (NGCC) electricity generation with carbon dioxide capture and storage (CCS). The CCS chain modeled in this study consists of carbon dioxide (CO₂) capture from flue gas using monoethanolamine (MEA), pipeline transport and storage in a saline aquifer.Results show that the sequestration of 90% CO₂ from the flue gas results in avoiding 70% of CO₂ emissions to the atmosphere per kWh and reduces global warming potential (GWP) by 64%. Calculation of other environmental impacts shows the trade-offs: an increase of 43% in acidification, 35% in eutrophication, and 120–170% in various toxicity impacts. Given the assumptions employed in this analysis, emissions of MEA and formaldehyde during capture process and generation of reclaimer wastes contributes to various toxicity potentials and cause many-fold increase in the on-site direct freshwater ecotoxicity and terrestrial ecotoxicity impacts. NO_x from fuel combustion is still the dominant contributor to most direct impacts, other than toxicity potentials and GWP. It is found that the direct emission of MEA contribute little to human toxicity (HT < 1%), however it makes 16% of terrestrial ecotoxicity impact. Hazardous reclaimer waste causes significant freshwater and marine ecotoxicity impacts. Most increases in impact are due to increased fuel requirements or increased investments and operating inputs.The reductions in GWP range from 58% to 68% for the worst-case to best-case CCS system. Acidification, eutrophication and toxicity potentials show an even large range of variation in the sensitivity analysis. Decreases in energy use and solvent degradation will significantly reduce the impact in all categories.     

Environmental impacts of different food waste resource technologies and the effects of energy mix

The environmental impacts of food waste management strategies and the effects of energy mix were evaluated using a life cycle assessment model, EASEWASTE. Three different strategies involving landfill, composting and combined digestion and composting as core technologies were investigated. The results indicate that the landfilling of food waste has an obvious impact on global warming, although the power recovery from landfill gas counteracts some of this. Food waste composting causes serious acidification (68.0 PE) and nutrient enrichment (76.9 PE) because of NH₃ and SO₂ emissions during decomposition. Using compost on farmland, which can marginally reduce global warming (−1.7 PE), acidification (−0.8 PE), and ecotoxicity and human toxicity through fertilizer substitution, also leads to nutrient enrichment as neutralization of emissions from N loss (27.6 PE) and substitution (−12.8 PE). A combined digestion and composting technology lessens the effects of acidification (−12.2 PE), nutrient enrichment (−5.7 PE), and global warming (−7.9 PE) mainly because energy is recovered efficiently, which decreases emissions including SO₂, Hg, NO_x, and fossil CO₂ during normal energy production. The change of energy mix by introducing more clean energy, which has marginal effects on the performance of composting strategy, results in apparently more loading to acidification and nutrient enrichment in the other two strategies. These are mainly because the recovered energy can avoid fewer emissions than before due to the lower background values in power generation. These results provide quantitative evidence for technical selection and pollution control in food waste management.     

Estimation of biogenic emissions with satellite-derived land use and land cover data for air quality modeling of Houston-Galveston ozone nonattainment area

The Houston-Galveston Area (HGA) is one of the most severe ozone non-attainment regions in the US. To study the effectiveness of controlling anthropogenic emissions to mitigate regional ozone nonattainment problems, it is necessary to utilize adequate datasets describing the environmental conditions that influence the photochemical reactivity of the ambient atmosphere. Compared to the anthropogenic emissions from point and mobile sources, there are large uncertainties in the locations and amounts of biogenic emissions. For regional air quality modeling applications, biogenic emissions are not directly measured but are usually estimated with meteorological data such as photo-synthetically active solar radiation, surface temperature, land type, and vegetation database. In this paper, we characterize these meteorological input parameters and two different land use land cover datasets available for HGA: the conventional biogenic vegetation/land use data and satellite-derived high-resolution land cover data. We describe the procedures used for the estimation of biogenic emissions with the satellite derived land cover data and leaf mass density information. Air quality model simulations were performed using both the original and the new biogenic emissions estimates. The results showed that there were considerable uncertainties in biogenic emissions inputs. Subsequently, ozone predictions were affected up to 10 ppb, but the magnitudes and locations of peak ozone varied each day depending on the upwind or downwind positions of the biogenic emission sources relative to the anthropogenic NOx and VOC sources. Although the assessment had limitations such as heterogeneity in the spatial resolutions, the study highlighted the significance of biogenic emissions uncertainty on air quality predictions. However, the study did not allow extrapolation of the directional changes in air quality corresponding to the changes in LULC because the two datasets were based on vastly different LULC category definitions and uncertainties in the vegetation distributions.     

Development and testing of AZEP reactor components

The advanced zero emissions power plant (AZEP) project addresses the development of a novel “zero emissions,” gas turbine-based, power generation process to reduce local and global CO₂ emissions in a cost-effective way.The key element in AZEP is an integrated MCM-reactor, in which (a) O₂ is separated from air by means of a mixed-conducting membrane (MCM), (b) combustion of natural gas occurs in an N₂-free environment and (c) the heat of combustion is transferred to air by heat exchange.This paper focuses on the development and testing of the ceramic components of the MCM-reactor (air separation membrane and heat exchangers). For compactness and manufacturability, a module design based on extruded square channel monoliths has been chosen. The manifold design enables gas distribution in a checkerboard pattern. Modules with contact area of >500 m²/m³ have been produced.Results from testing of the modules under close to realistic process conditions agree with model predictions. Extrapolation to AZEP process conditions gives an oxygen production rate of around 37 mol O₂/(m³ s), or 15 MW/m³ power density (per net MCM volume). These values correspond to project targets and confirm the feasibility of the AZEP concept.     

The potential for increased atmospheric CO2 emissions and accelerated consumption of deep geologic CO2 storage resources resulting from the large-scale deployment of a CCS-enabled unconventional fossil fuels industry in the U.S.

Desires to enhance the energy security of the United States have spurred renewed interest in the development of abundant domestic heavy hydrocarbon resources including oil shale and coal to produce unconventional liquid fuels to supplement conventional oil supplies. However, the production processes for these unconventional fossil fuels create large quantities of carbon dioxide (CO₂) and this remains one of the key arguments against such development. Carbon dioxide capture and storage (CCS) technologies could reduce these emissions and preliminary analysis of regional CO₂ storage capacity in locations where such facilities might be sited within the U.S. indicates that there appears to be sufficient storage capacity, primarily in deep saline formations, to accommodate the CO₂ from these industries. Nevertheless, even assuming wide-scale availability of cost-effective CO₂ capture and geologic storage resources, the emergence of a domestic U.S. oil shale or coal-to-liquids (CTL) industry would be responsible for significant increases in CO₂ emissions to the atmosphere. The authors present modeling results of two future hypothetical climate policy scenarios that indicate that the oil shale production facilities required to produce 3 MMB/d from the Eocene Green River Formation of the western U.S. using an in situ retorting process would result in net emissions to the atmosphere of between 3000 and 7000 MtCO₂, in addition to storing potentially 900–5000 MtCO₂ in regional deep geologic formations via CCS in the period up to 2050. A similarly sized, but geographically more dispersed domestic CTL industry could result in 4000–5000 MtCO₂ emitted to the atmosphere in addition to potentially 21,000–22,000 MtCO₂ stored in regional deep geologic formations over the same period. While this analysis shows that there is likely adequate CO₂ storage capacity in the regions where these technologies are likely to deploy, the reliance by these industries on large-scale CCS could result in an accelerated rate of utilization of the nation's CO₂ storage resource, leaving less high-quality storage capacity for other carbon-producing industries including electric power generation.     

The energy,water, and air pollution implications of tapping China's shale gas reserves

China has laid out an ambitious strategy for developing its vast shale gas reserves. This study developed an input–output based hybrid life-cycle inventory model to estimate the energy use, water consumption, and air emissions implications of shale gas infrastructure development in China over the period 2013–2020, including well drilling and operation, land rig and fracturing fleet manufacture, and pipeline construction. Multiple scenarios were analyzed based on different combinations of well development rates, well productivities, and success rates. Results suggest that 700–5100 petajoules (PJ) of primary energy will be required for shale gas infrastructure development, while the net primary energy yield of shale gas production over 2013–2020 was estimated at 1650–7150 PJ, suggesting a favorable energy balance. Associated emissions of CO₂e were estimated at 80–580 million metric tons, and were primarily attributable to coal-fired electricity generation, fugitive methane, and flaring of methane during shale gas processing and transmission. Direct water consumption was estimated at 20–720 million metric tons. The largest sources of energy use and emissions for infrastructure development were the metals, mining, non-metal mineral products, and power sectors, which should be the focus of energy efficiency initiatives to reduce the impacts of shale gas infrastructure development moving forward.     

Impact of riverbank filtration on treatment of polluted river water

The impact of riverbank filtration (RBF) on the treatment of water from the River Yamuna at Mathura, which has disagreeable visual properties, has been investigated. The dissolved organic carbon (DOC) and colour of the river water were 4.0–6.8 mg/L and 40–65 colour units (CU), respectively. Pre-chlorination is in practice to improve raw water quality. Chlorine doses as high as 60 mg/L ahead of the water treatment units reduced colour by about 78%. Removal of DOC and UV-absorbance was less than 18%. In comparison to direct pumping of the river water, collection of water through RBF resulted in the reduction of DOC, colour, UV-absorbance and fecal coliforms by around 50%. However, riverbank filtrate did not conform to the drinking water quality standards. Therefore, riverbank-filtered water along with the Yamuna water were ozonated for different durations. To reduce DOC to the desired level, the dose of ozone required for the riverbank filtrate was found to be considerably less than the ozone required for the river water. RBF as compared to direct pumping of Yamuna water appears to be effective in improving the quality of the raw water.     

The cost of crop damage caused by ozone air pollution from motor vehicles

The effects of ozone air pollution on the agricultural sector are an important environmental challenge facing policy makers. Most studies of the economic impact of air pollution on agriculture have found that a 25% reduction in ambient ozone would provide benefits of at least $1–2 billion annually in the United States. This paper extends existing research by estimating the benefits of a reduction in emissions from a major source of ozone formation: motor-vehicle emissions. An agricultural production model is combined with an analysis of motor-vehicle emissions and air quality to estimate the impacts of emissions from six different motor-vehicle classes, at both the regional and national level. The benefits to the agricultural sector from completely eliminating ozone precursor emissions from motor vehicles ranges between $3·5 and $6·1 billion annually.     

Mineralization of integrated gasification combined-cycle power-station wastewater effluent by a photo-fenton process

The aim of this work was to study the mineralization of wastewater effluent from an integrated-gasification combined-cycle (IGCC) power station sited in Spain to meet the requirements of future environmental legislation. This study was done in a pilot plant using a homogeneous photo-Fenton oxidation process with continuous addition of H₂O₂ and air to the system.The mineralization process was found to follow pseudo-first-order kinetics. Experimental kinetic constants were fitted using neural networks (NNs). The NNs model reproduced the experimental data to within a 90% confidence level and allowed the simulation of the process for any values of the parameters within the experimental range studied. At the optimum conditions (H₂O₂ flow rate = 120 mL/h, [Fe(II)] = 7.6 mg/L, pH = 3.75 and air flow rate = 1 m³/h), a 90% mineralization was achieved in 150 min.Determination of the hydrogen peroxide consumed and remaining in the water revealed that 1.2 mol of H₂O₂ was consumed per each mol of total organic carbon removed from solution. This result confirmed that an excess of dissolved H₂O₂ was needed to achieve high mineralization rates, so continuous addition of peroxide is recommended for industrial application of this process.Air flow slightly improved the mineralization rate due to the formation of peroxo-organic radicals which enhanced the oxidation process.