Use of constructed wetland for the removal of heavy metals from industrial wastewater

This study was conducted to investigate the effectiveness of a continuous free surface flow wetland for removal of heavy metals from industrial wastewater, in Gadoon Amazai Industrial Estate (GAIE), Swabi, Pakistan. Industrial wastewater samples were collected from the in-let, out-let and all cells of the constructed wetland (CW) and analyzed for heavy metals such as lead (Pb), cadmium (Cd), iron (Fe), nickel (Ni), chromium (Cr) and copper (Cu) using standard methods. Similarly, samples of aquatic macrophytes and sediments were also analyzed for selected heavy metals. Results indicate that the removal efficiencies of the CW for Pb, Cd, Fe, Ni, Cr, and Cu were 50%, 91.9%, 74.1%, 40.9%, 89%, and 48.3%, respectively. Furthermore, the performance of the CW was efficient enough to remove the heavy metals, particularly Cd, Fe, and Cu, from the industrial wastewater fed to it. However, it is suggested that the metal removal efficiency of the CW can be further enhanced by using proper management of vegetation and area expansion of the present CW.     

Bioproduction of ferric sulfate used during heavy metals removal from sewage sludge

Toxic metals removal from wastewater sewage sludge can be achieved through microbial processes involving Acidithiobacillus ferrooxidans. The oxidation of ferrous ions by A. ferrooxidans, cultured in sewage sludge filtrate, was studied in both batch and continuous flow stirred tank reactors. Sewage sludge filtrate containing natural nutrients (phosphorus and nitrogen) was recovered as effluent following the dehydration of a primary and secondary sludge mixture. Batch and continuous flow stirred tank reactor tests demonstrated that A. ferrooxidans were able to grow and completely oxidize ferrous iron in a culture medium containing more than 80% (v v(-1)) sewage sludge filtrate with 10 g Fe(II) L(-1) added. Toxic levels were reached when total organic carbon in the sewage sludge filtrate exceeded 250 mg L(-1). The ferric iron solution produced in the sludge filtrate by A. ferrooxidans was used to solubilize heavy metals in primary and secondary sludge. The solubilization of Cu, Cr, and Zn yielded 71, 49, and 80%, respectively. This is comparable with the yield percentages obtained using a FeCl(3) solution. The cost of treating wastewater sewage sludge by bioproducing a ferric ion solution from sewage sludge is three times less expensive than the conventional method requiring a commercial ferric chloride solution.     

Experimental investigation of adsorption capacity of anthill in the removal of heavy metals from aqueous solution

In the present work, the adsorption capacity of anthill was investigated as a low‐cost adsorbent to remove the heavy metal ions, lead (II) ion (Pb²⁺), and zinc (II) ion (Zn²⁺) from an aqueous solution. The equilibrium adsorption isotherms of the heavy metal ions were investigated under batch process. For the study we examined the effect of the solution's pH and the initial cations concentrations on the adsorption process under a fixed contact time and temperature. The anthill sample was characterized using a scanning electron microscope (SEM), X‐ray fluorescence (XRF), and Fourier transform infrared (FTIR) techniques. From the SEM analysis, structural change in the adsorbent was a result of heavy metals adsorption. Based on the XRF analysis, the main composition of the anthill sample was silica (SiO₂), alumina (Al₂O₃), and zirconia (ZrO₂). The change in the peaks of the spectra before and after adsorption indicated that there was active participation of surface functional groups during the adsorption process. The experimental data obtained were analyzed using 2‐ and 3‐parameter isotherm models. The isotherm data fitted very well to the 3‐parameter Radke–Prausnitz model. It was noted that Pb²⁺ and Zn²⁺ can be effectively removed from aqueous solution using anthill as an adsorbent.     

Influence of vegetation on the removal of heavy metals and nutrients in a constructed wetland

A free water surface wetland was built to treat wastewater containing metals (Cr, Ni, Zn) and nutrients from a tool factory in Argentina. Water, sediment and macrophytes were sampled in the inlet and outlet area of the constructed wetland during three years. Three successive phases of vegetation dominance were developed and three different patterns of contaminant retention were observed. During the Eichhornia crassipes dominance, contaminants were retained in the macrophyte biomass; during the E. crassipes+Typha domingensis stage, contaminants were retained in the sediment and in the T. domingensis dominance stage, contaminants were retained in sediment and in the macrophyte biomass. Removal efficiency was not significantly different among the three vegetation stages, except for NH(4)(+) and i-P(diss). Because of its highest tolerance, T. domingensis is the best choice to treat wastewater of high pH and conductivity with heavy metals, a common result from many industrial processes.     

Biological alkylation and colloid formation of selenium in methanogenic UASB reactors

Bioalkylation and colloid formation of selenium during selenate removal in upflow anaerobic sludge bed (UASB) bioreactors was investigated. The mesophilic (30 degrees C) UASB reactor (pH = 7.0) was operated for 175 d with lactate as electron donor at an organic loading rate of 2 g COD L(-1) d(-1) and a selenium loading rate of 3.16 mg Se L(-1) d(-1). Combining sequential filtration with ion chromatographic analysis for selenium oxyanions and solid phase micro extraction gas chromatography mass spectrometry (SPME-GC-MS) for alkylated selenium compounds allowed to entirely close the selenium mass balance in the liquid phase for most of the UASB operational runtime. Although selenate was removed to more than 98.6% from the liquid phase, a less efficient removal of dissolved selenium was observed due to the presence of dissolved alkylated selenium species (dimethylselenide and dimethyldiselenide) and colloidal selenium particles in the effluent. The alkylated and the colloidal fractions contributed up to 15 and 31%, respectively, to the dissolved selenium concentration. The size fractions of the colloidal dispersion were: 4 to 0.45 mum: up to 21%, 0.45 to 0.2 mum: up to 11%, and particles smaller than 0.2 mum: up to 8%. Particles of 4 to 0.45 mum were formed in the external settler, but did not settle. SEM-EDX analysis showed that microorganisms form these selenium containing colloidal particles extracellularly on their surface. Lowering the temperature by 10 degrees C for 6 h resulted in drastically reduced selenate removal efficiencies (after a delay of 1.5 d), accompanied by the temporary formation of an unknown, soluble, organic selenium species. This study shows that a careful process control is a prerequisite for selenium treatment in UASB bioreactors, as disturbances in the operational conditions induce elevated selenium effluent concentrations by alkylation and colloid formation.     

Effects of impurities on the removal of heavy metals by natural limestones in aqueous systems

Effects of impurities on the removal of heavy metals by natural limestones in aqueous solutions were studied by evaluating various factors including limestone concentration, pH, contact time and temperature. Solutions of Pb(II), Cd(II), Cu(II) and Zn(II), prepared from chloride reagents at a concentration of 10 mg/L, were studied in a batch method. Four natural limestone samples, collected from the Campanian-Maastrichtian limestone beds in Tunisia, were used as adsorbents. Sorption experiments indicated that high removal efficiencies could be achieved. Limestone samples containing impurities, such as silica, iron/aluminum oxides and different kinds of clay minerals, demonstrated enhanced sorption capacity, nearing 100% removal in some cases. Kinetic experiments showed that the sorption of metal ions occurred rapidly at a low coverage stage, and that solutions were nearly at equilibrium after 60 min. Data trends generally fit pseudo-second order kinetic, and intra-particle diffusion, models. The following conditions were found to promote optimum, or near-optimum, sorption of heavy metals: 1) contact time of more than 60 min, 2) pH = 5, 3) >3 g/L limestone concentration and 4) T = 35 °C. The results of this study suggest that the limestones from northern Tunisia, that contain higher amounts of silica and iron/aluminum oxides, are promising adsorbents for the effective removal of toxic heavy metals from wastewaters.     

Interparticle diffusion and thermodynamic modeling studies for the removal of heavy metals using mixed adsorbents in industrial effluents

Pollution of water, air, and soil by industrial effluents is a major problem nowadays. A variety of contaminants are too responsible for changing the physicochemical properties of the receiving body. There are practical treatment solutions available to clean up contaminants from various resources. The term “adsorption” refers to one of them. The purpose of the research work is to remove heavy metals from industrial effluent. Mixed adsorbents prepared from activated charcoal and bone charcoals were used to remove the copper and cadmium ions. The experiment carried out in a batch operation and modeling of these data for intraparticle diffusion and thermodynamic calculations were reported in this research work. At optimum operating condition pH 6; metal ion concentration 50 mg/L; dose 5 g/L; agitation 180 rpm and temperature 40°C maximum 99.41% copper ions and 88.12% cadmium ion removal was achieved. Cadmium ions were well fitted in the thermodynamic model compared to copper ions, as demonstrated by the higher correlation coefficient R² (0.9824) value. Intra particle diffusion demonstrated that film diffusion was a rate-limiting step at the start of the reaction, while microporous intraparticle diffusion was the rate-determining phase later on. A Fourier transformation infrared spectroscopy, X-ray diffraction, and scanning electron micrography analysis confirmed the suitability of mixed adsorbents for the removal of cadmium and copper metal ions.     

Evaluation of heavy metals accumulation by two emergent macrophytes from the polluted soil: an experimental study

The concentrations of copper (Cu) and lead (Pb) in, and the biomass of, the different parts of Persicaria glabra (Willd.) Gamez and Juncellus alopecuroides (Rottb.) C.B.Cl. were evaluated while grown in pots under laboratory conditions. Cu and Pb were added as sulphates (50, 100, 200, 400 mg/kg) to the pots. Heavy metal concentrations in the plants were measured by atomic absorption spectrometry. Results reveal that the biomass of J. alopecuroides (particularly roots) was higher than P. glabra, and that the growth tendency of macrophytes decreased with increasing heavy metal concentration in the soil, while in P. glabra, biomass went on increasing with the increase in copper concentration. Heavy metal accumulation in the roots was more than in aerial parts, and, therefore, barring two exceptions, the transfer factor of heavy metals from roots to aerial parts showed as less than 1, suggesting less transfer of heavy metals from roots to aerial parts. Thus, these macrophytes are efficient accumulators of trace elements, particularly J. alopecuroides, which can be recommended for biofiltration of heavy metals from contaminated soils.     

Sorption of hazardous metals from single and multi-element solutions by saltbush biomass in batch and continuous mode: interference of calcium and magnesium in batch mode

Batch studies were performed to determine the interference of calcium (Ca) and magnesium (Mg) on the sorption of Cu(II), Cd(II), Cr(III), Cr(VI), Pb(II), and Zn(II) [from CuSO(4), K(2)Cr(2)O(7), Pb(NO(3))(2), Cr(NO(3))(3), ZnCl(2), and Cd(NO(3))(2)] by saltbush (Atriplex canescens) biomass. The results demonstrated that Ca and Mg at concentrations of at least 20 times higher than the concentration of most of the target metals did not interfere with the metal binding. The data show that the batch binding capacity from a multimetal solution at pH 5.0 was (micromol/g) about 260 for Cr(III) and Pb, and about 117, 54, and 49 for Cu, Zn, and Cd, respectively. The use of 0.1M HCl allowed the recovery of 85-100% of the bound Cu, Cr(III), and Pb, and more than 37% of the bound Cd and Zn. The column binding capacity for Pb was about 49 micromol/g from both the single and multimetal solutions, while it was, respectively about 35 and 23 micromol/g for Cr(III). The binding capacity for Cu and Zn from the single and multimetal column experiments was 35 micromol/g and less than 10 micromol/g, respectively. The stripping data from the single column experiment showed that 0.1M HCl allowed the recovery of all the bound Cu and Zn, 90% and 74% of the bound Pb and Cr(VI), respectively, and less than 25% of the bound Cd and Cr(III), while the stripping from the multimetal experiment showed that 0.1M HCl allowed the recovery of all the bound Cu and about 74%, 54%, 43%, and 40% of the bound Pb, Zn, Cd, and Cr(III), respectively.     

Removal of heavy metals in rinsing wastewater from plating factory by adsorption with economical viable materials

The removal of heavy metals from plating factory wastewater with economical materials was investigated by the column method. Montmorillonite, kaolin, tobermorite, magnetite, silica gel and alumina were used as the economical adsorbents to wastewater containing Cd(II), Cr(VI), Cu(II) and Pb(II). This removal method of heavy metals proved highly effective as removal efficiency tended to increase with increasing pH and decrease with increasing metal concentration. The removal percentages by adsorption onto montmorillonite, tobermorite, magnetite, and silica gel showed high values for all metals. From the results for the heat of adsorption, the adsorption process in the present study might be chemisorption. The proposed method was successfully applied to the removal of Cd(II), Cr(VI) and Cu(II) in rinsing wastewater from plating factory in Nagoya City, Aichi Prefecture, Japan. Since the economical adsorbents used can be obtained commercially because they are easily synthesized, the wastewater treatment system developed is rapid, simple and cheap for the removal of heavy metals.     

Determining contamination level of heavy metals in road dust from busy traffic areas with different characteristics

This study identified the levels and sources of heavy metal contamination in road dust from busy traffic areas in a typical industrial city in Korea. This study compared the total concentrations, as determined by aqua regia digestions and atomic absorption spectroscopy, of cadmium (Cd), copper (Cu), lead (Pb), zinc (Zn) and nickel (Ni) in the road dust from areas with different characteristics such as traffic rotaries, downtown areas, circulation roads, and asphalt and concrete highways. The contamination levels of the heavy metals in the road dust were evaluated using the contamination factor and the degree of contamination. The contamination levels of the heavy metals in the road dust were highly dependent on traffic volume and atmospheric dispersion from traffic rotaries. Industrial emissions and the frequency of brake use and vehicles coming to a complete stop were additional factors that affected the contamination levels in downtown areas. The concrete highway had higher contamination levels of the heavy metals than the asphalt highway. Vehicle speed was also a strong contributing factor to the degree of contamination of heavy metals in the road dust from the circulation roads and highways.     

Bioenergy production from roadside grass: A case study of the feasibility of using roadside grass for biogas production in Denmark

This paper presents a study of the feasibility of utilising roadside vegetation for biogas production in Denmark. The potential biomass yield, methane yields, and the energy balances of using roadside grass for biogas production was investigated based on spatial analysis. The results show that the potential annual yield of biomass obtainable from roadside verges varies widely depending on the local conditions. The net energy gain (NEG) from harvest, collection, transport, storage and digestion of roadside vegetation was estimated to range from 60,126–121,476 GJ, corresponding to 1.5–3.0% of the present national energy production based on biogas. The estimated values for the energy return on invested energy (EROEI) was found to range from 2.17 to 2.88. The measured contents of heavy metals in the roadside vegetation was seen not to exceed the legislative levels for what can be applied as fertilizer on agricultural land, neither does it reach levels considered as inhibitory for the anaerobic fermentation process. From a practical point of view, few challenges were identified related to the acquisition and processing of the roadside vegetation. Considering the positive net energy gains, further energy investments for management of these challenges can be made. Despite the somewhat low EROEI values, the use of this resource could however result in other positive externalities, such as improved biodiversity of the verges and recycling of nutrients.     

Solubility of phosphorus and heavy metals in potting media amended with yard waste-biosolids compost

The potential risk of surface and ground water contamination by phosphorus (P) and heavy metals leached from compost-based containerized media has become an environmental concern. Solubility and fractionation of P and heavy metals were evaluated in media containing 0, 25, 50, 75, or 100% compost derived from biosolids and yard trimmings for potential impacts on the environment. As compost proportion in peat-based media increased from 0 to 100%, concentrations of total P, Cd, Cu, Ni, Pb, Zn, and Mn in the media increased whereas concentrations of total Co and Cr decreased. Except for Cu, all heavy metals in the water-soluble fraction decreased with increasing compost proportion in the media, because of higher Fe, Al, and Ca concentrations and pH values of the composts than the peat. When the media pH is controlled and maintained at normal range of plant growth (5.5-6.5), leaching of the heavy metals is minimal. Incorporation of compost to the peat-based media also decreased the proportion of total P that was water-soluble. However, concentrations of bioavailable inorganic phosphorus (NaHCO3-IP), readily mineralizable organic phosphorus (NaHCO3-OP), potentially bioavailable inorganic phosphorus (NaOH-IP), and potentially bioavailable organic phosphorus (NaOH-OP) were still higher in the media amended with compost because of higher total P concentration in the compost. Further study is needed to verify if less or no topdressing of chemical P fertilizer should be applied to the compost-amended media to minimize P effect on the environment when compost-amended potting media are used for nursery or greenhouse crop production systems.     

Retention of heavy metals in a Typic Kandiudult amended with different manure-based biochars

Although nutrient-rich manure biochars are expected to be an effective heavy metal stabilizer in agricultural and contaminated soils, systematic studies are lacking to predict the influence of manure variety and pyrolysis temperature on metal-binding potentials. In this study, biochars produced from five manure varieties (dairy, paved feedlot, swine solids, poultry litter, and turkey litter) at two pyrolytic temperatures (350 and 700°C) were examined for the stabilization of Pb, Cu, Ni, and Cd in a weathered, acidic Norfolk loamy sand (fine-loamy, kaolinitic, thermic, Typic Kandiudult). Equilibrium concentrations in the aqueous phase were determined for heavy metals (Cu, Ni, Cd, and Pb) and additional selected elements (Na, P, S, Ca, Mg, Al, and K); these were analyzed by positive matrix factorization to quantitatively determine the factors responsible for the biochar's ability to bind the selected heavy metals in soil. Concurrently with the greatest increase in pH and highest equilibrium Na, S, and K concentrations, poultry litter, turkey litter, and feedlot 700°C biochar exhibited the greatest heavy metal retention. In contrast, manure varieties containing disproportionately high (swine) and low (dairy) ash, P, and other elements were the least effective stabilizers. Regardless of the manure type, proton nuclear magnetic resonance analyses showed the removal of leachable aliphatic and nitrogen-containing heteroaromatic functional groups at the higher (700°C) pyrolysis temperature. Consistently greater Cu retention by the 700°C biochar indicated the mobilization of Cu by 350°C biochar-born dissolved organic carbon; however, the influence of other temperature-dependent biochar characteristics cannot be ruled out.     

Utilization of pulp and paper industrial wastes to remove heavy metals from metal finishing wastewater

Two pulp and paper industrial wastes, lime mud (LM) and recovery boiler ash (RB), have low moisture contents, low heavy metal contaminations and contain various carbonate compounds which contribute to a high pH. Metal finishing wastewater (MF-WW) has a low pH, high levels of TDS and high contaminations from Cr, Cu, Pb and Zn. The heavy metals from MF-WW were removed by sorption and precipitation mechanisms. LM gave better results in removing heavy metals from MF-WW than RB. At a reaction time of 45 min, the maximum removal efficiencies for Cr (93%) and Cu (99%) were obtained at 110 g L⁻¹ of LM, but at 80 g L⁻¹ for Pb (96%) and Zn (99%). Treatment with LM gives a higher sludge volume than with RB. However, the leachability of heavy metals from LM is lower. Leachability of heavy metals in the sediment for all selected treatment conditions is within government standards.     

Uncertainty and sensitivity analysis of spatial predictions of heavy metals in wheat

Heavy metals seriously threaten the health of human beings when they enter the food chain. Therefore, policymakers require precise predictions of heavy metal concentrations in agricultural crops. In this paper we quantify the uncertainty of regression predictions of Cd and Pb in wheat (Triticum aestivum L.) and the contributions to the uncertainties in these predictions associated with inputs to the regression model. For each node of the 500- x 500-m grid covering the arable soils in The Netherlands, a latin hypercube sample size of 1000 is constructed from the uncertainty distributions of the explanatory variables (pH, soil organic matter [SOM], and heavy metal concentration in soil), the regression coefficients, and the random term of the regression model. This sample is used as input for the regression model to obtain 1000 values from the uncertainty distributions of the log(Cd) and log(Pb) concentration in wheat. There were no nodes where the recent EU quality standards for Cd and Pb (0.2 mg kg(-1) fresh wt.) in wheat were almost certain to be exceeded. For most nodes with clay soils, the quality standard for Cd in wheat almost certainly will not be exceeded; for Pb this is much less certain. The uncertainty in the Cd concentration in soil contributes most to the uncertainty in the predicted Cd concentrations in wheat (36% on the average), followed by the random term of the regression model (23%). For Pb the contribution of the random term is by far the largest (52%).     

Anaerobic digestion of agro-industrial waste enriched with bovine bone meal for improved biogas production and biofertilization

The increase in animal and agro-industrial production must be accompanied by the development of appropriate waste and by-product management strategies. Anaerobic digestion is a promising approach to recycle these wastes and reintegrate them into the economic production cycle of biogas and biofertilizer. In order to improve the performance of the anaerobic mesophilic digestion of abundant agro-industrial wastes constituted by potato peel (PP), and poultry waste (PW) and study the contribution of bovine bone meal (BB) as additive rich in phosphorus, which can help to neutralize the acidity of the substrate. The 10-point simplex-centroid design and the isoresponse surfaces strategy were used. This study demonstrated that in mesophilic bio-digestion, the using bovine bones in admixture with agroindustrial residue provided for the proper balance of chemical components required for proliferation of microbiological agent of bioconversion, which also resulted in an increase in biogas production capacity. The best formula was so composed by 66.67% bovine bone, 16.67% potatoes peel, and 16.67% poultry waste. The stability was achieved here after only 12 days. The digestate generated from it was fulfilled with the microbiological and chemical requirements for safety defined by the NF U44-551 standard. Germination test revealed that this optimal produced digestate, did not hinder growth, in fact, almost 85% of seed was germinated. Finally, fertilization experiments prove that this digestate can boost the growth of bell pepper (Capsicum annuum).     

Dissolution kinetics of heavy metals in Dutch carbonate- and sulfide-rich freshwater sediments

In two sulfide-rich freshwater sediments from the Biesbosch and Kromme Rijn River in the Netherlands differing in carbonate content and acid volatile sulfide (AVS) content, metal and sulfide dissolution kinetics were studied at different acid concentrations by varying both the procedure of acid addition and the extraction time. The establishment of equilibrium was monitored by measuring the pH in time, which reached a near constant value. The equilibrium pH was reached quickly when large amounts of acid were added and slowly when small amounts of acid were added. This observation was confirmed by the yield of extracted metals after either a 45-min or 24-h extraction over a pH range from 0 to 5. The pH factor seemed to be of more influence than time for the dissolution of metals. The amount of extracted metals was highly dependent on the metal itself due to its physico-chemical behavior. Although the sediments studied varied in carbonate content, acid volatile sulfide (AVS), and total metal content, the extracted fraction of metals compared with their total content in the sediment was similar for most metals. Finally, the AVS content as well as the ratio of simultaneously extracted metals (SEM; sum of Cd, Cu, Ni, Pb, and Zn) to AVS decreased with increasing pH. Because the SEM to AVS ratio may be used to set environmental quality criteria for the sediment compartment, this observation is of significance.     

Phytoremediation and long-term site management of soil contaminated with pentachlorophenol (PCP) and heavy metals

Pentachlorophenol (PCP) is a persistent organic pollutant (POP) previously used as a timber treatment chemical to prevent sap stain and wood rot. Commonly used in wood treatment industries for the last 50 years, there are now many sites worldwide that are contaminated with PCP. Although persistent, PCP is a mobile contaminant and therefore has a propensity to leach and contaminate surrounding environments. Both willow (Salix sp., 'Tangoio') and poplar (Populus sp. 'Kawa') growing in an open-ended plastic greenhouse were found to tolerate soil PCP concentrations of 250 mg kg(-1) or less and both species stimulated a significant increase in soil microbial activity when compared to unplanted controls. Both poplar and willow could not survive PCP concentrations above 250 mg kg(-1) in soil. Pentachlorophenol degradation occurred in both planted and unplanted pots, but a higher rate of degradation was observed in the planted pots. Soil contaminated by wood-treatment activities often contains co-contaminants such as B, Cr, Cu and As, that are also used as timber preservatives. An additional column leaching experiment, done along side the potted trial, found that PCP, B, Cr, Cu and As were all present in the column leachate. This indicates that although Cu, Cr and As are generally considered immobile in the soil, they were mobilised under our column conditions. If a contaminated site were to be hydraulically 'sealed' using plants, a reticulation irrigation system should be installed to capture any contaminant leachate resulting from heavy rains. This captured leachate can either be independently treated, or reapplied to the site. Our data demonstrate a reduction in soil hydraulic conductivity with repeated application of leachate containing PCP and metal compounds but the soil did not become anaerobic. This would need to be considered in site remediation design.     

Geochemical properties and pollution assessment of heavy metals in the sediments of Daechung Lake,Korea

In order to examine the forms, sources, and pollution of heavy metals—arsenic (As), aluminum (Al), cadmium (Cd), chromium (Cr), copper (Cu), iron (Fe), nickel (Ni), lead (Pb), and zinc (Zn)—in Daechung Lake, Korea, sediment samples were collected in November 2014. Daechung Lake was constructed to supply water for human consumption, agricultural use, and industrial use as well as to generate electric power. The lake is stratified in the summer and surrounded mostly by agricultural and mining areas. Our results indicate that the heavy metals (except As and Cd) displayed similar concentrations at all of the sampling stations. As and Cd were high in locations where fine sediments had built up. Based on the enrichment factor of the metals, the sediments collected from all of the sampling stations were highly polluted by As and Cd. Therefore, deposition of heavy metals in Daechung Lake is possibly controlled by grain size and anthropogenic activity, such as drainage from abandoned mines, agricultural activities, and/or the release of wastewater. The most dominant forms for all of the metals were oxide and silicate forms. This suggests that the sediments of Daechung Lake are not highly sulfidic. However, the sediment samples were collected after the collapse of seasonal stratification. Therefore, future studies should include elucidation of major sources for As and Cd and the collection of sediments during months of stratification.