Integration of post-combustion capture and storage into a pulverized coal-fired power plant

Post-combustion CO₂ capture and storage (CCS) presents a promising strategy to capture, compress, transport and store CO₂ from a high volume–low pressure flue gas stream emitted from a fossil fuel-fired power plant. This work undertakes the simulation of CO₂ capture and compression integration into an 800 MW_e supercritical coal-fired power plant using chemical process simulators. The focus is not only on the simulation of full load of flue gas stream into the CO₂ capture and compression, but also, on the impact of a partial load. The result reveals that the energy penalty of a low capture efficiency, for example, at 50% capture efficiency with 10% flue gas load is higher than for 90% flue gas load at the equivalent capture efficiency by about 440 kWh_e/tonne CO₂. The study also addresses the effect of CO₂ capture performance by different coal ranks. It is found that lignite pulverized coal (PC)-fired power plant has a higher energy requirement than subbituminous and bituminous PC-fired power plants by 40.1 and 98.6 MW_e, respectively. In addition to the investigation of energy requirement, other significant parameters including energy penalty, plant efficiency, amine flow rate and extracted steam flow rate, are also presented. The study reveals that operating at partial load, for example at half load with 90% CO₂ capture efficiency, as compared with full load, reduces the energy penalty, plant efficiency drop, amine flow rate and extracted steam flow rate by 9.9%, 24.4%, 50.0% and 49.9%, respectively. In addition, the effect of steam extracted from different locations from a series of steam turbine with the objective to achieve the lowest possible energy penalty is evaluated. The simulation shows that a low extracted steam pressure from a series of steam turbines, for example at 300 kPa, minimizes the energy penalty by up to 25.3%.     

Designing a supercritical steam cycle to integrate the energy requirements of CO2 amine scrubbing

Absorption by chemical solvents combined with CO₂ long-term storage appears to offer interesting and commercial applicable CO₂ capture technology. However one of the main disadvantages is related to the large quantities of heat required to regenerate the amine solvent that means an important power plant efficiency penalty. Different studies have analyzed alternatives to reduce the heat duty on the reboiler and the thermal integration requirements on existing power cycles. In these studies integration principles have been well set up, but there is a lack of information about how to achieve an integrated design and the thermal balances of the modified cycle flowsheet. This paper proposes and provides details about a set of modifications of a supercritical steam cycle to overcome the energy requirements through energetic integration with the aim of reducing the efficiency and power output penalty associated with CO₂ capture process. Modifications include a new designed low-pressure heater flowsheet to take advantage of the CO₂ compression cooling for postcombustion systems and integration of amine reboiler into a steam cycle. It has been carried out several simulations in order to obtain power plant performance depending on sorbent regeneration requirements.     

Effective retrofitting of post-combustion CO2 capture to coal-fired power plants and insensitivity of CO2 abatement costs to base plant efficiency

Existing coal-fired power plants were not designed to be retrofitted with carbon dioxide post-combustion capture (PCC) and have tended to be disregarded as suitable candidates for carbon capture and storage on the grounds that such a retrofit would be uneconomical. Low plant efficiency and poor performance with capture compared to new-build projects are often cited as critical barriers to capture retrofit. Steam turbine retrofit solutions are presented that can achieve effective thermodynamic integration between a post-combustion CO₂ capture plant and associated CO₂ compressors and the steam cycle of an existing retrofitted unit for a wide range of initial steam turbine designs. The relative merits of these capture retrofit integration options with respect to flexibility of the capture system and solvent upgradability will be discussed. Provided that effective capture system integration can be achieved, it can be shown that the abatement costs (or cost per tonne of CO₂ to justify capture) for retrofitting existing units is independent of the initial plant efficiency. This then means that a greater number of existing power plants are potentially suitable for successful retrofits of post-combustion capture to reduce power sector emissions. Such a wider choice of retrofit sites would also give greater scope to exploit favourable site-specific conditions for CCS, such as ready access to geological storage.     

Exergy analysis as a tool for the integration of very complex energy systems: The case of carbonation/calcination CO2 systems in existing coal power plants

A common characteristic of carbon capture and storage systems is the important energy consumption associated with the CO₂ capture process. This important drawback can be solved with the analysis, synthesis and optimization of this type of energy systems. The second law of thermodynamics has proved to be an essential tool in power and chemical plant optimization. The exergy analysis method has demonstrated good results in the synthesis of complex systems and efficiency improvements in energy applications.In this paper, a synthesis of pinch analysis and second law analysis is used to show the optimum window design of the integration of a calcium looping cycle into an existing coal power plant for CO₂ capture. Results demonstrate that exergy analysis is an essential aid to reduce energy penalties in CO₂ capture energy systems. In particular, for the case of carbonation/calcination CO₂ systems integrated in existing coal power plants, almost 40% of the additional exergy consumption is available in the form of heat. Accordingly, the efficiency of the capture cycle depends strongly on the possibility of using this heat to produce extra steam (live, reheat and medium pressure) to generate extra power at steam turbine. The synthesis of pinch and second law analysis could reduce the additional coal consumption due to CO₂ capture 2.5 times, from 217 to 85 MW.     

Derivation of correlations to evaluate the impact of retrofitted post-combustion CO2 capture processes on steam power plant performance

When integrating a post-combustion CO₂ capture process and CO₂ compression into a steam power plant, the three interface quantities heat, electricity and cooling duty must be satisfied by the power plant, leading to a loss in net efficiency. The heat duty shows to be the largest contributor to the overall net efficiency penalty of the power plant. Additional energy penalty results from the cooling and electric power duty of the capture and compression units.In this work, the dependency of the energy penalty on the quantity and quality of the heat duty is analyzed and quantified for a state-of-the-art hard coal fired power plant. Furthermore, the energy penalty attributed to the additional cooling and power duty is quantified. As a result correlations are provided which enable to predict the impact of the heat, cooling and electricity duty of post-combustion CO₂ capture processes on the net output of a steam power plant in a holistic approach.     

Conceptual design of a three fluidised beds combustion system capturing CO2 with CaO

In this work, the Aspen Hysys conceptual design of a new process for energy generation at large scale with implicit CO₂ capture is presented. This process makes use of the CaO capability for CO₂ capture at high temperature and the possibility of regenerating this sorbent working in interconnected fluidised bed reactors operating at different temperatures. The proposed process has the advantage of producing power with minimum CO₂ emissions and very low energy penalties compared with similar air-based combustion power plants. In this system, five main parts can be distinguished: the combustor where coal is burnt with air, the calciner where the fresh and the recycled CaCO₃ is calcined, the carbonator where the CO₂ produced in the combustor is captured, the supercritical steam cycle and the CO₂ compression system. In this arrangement, the three fluidised bed reactors are interconnected in such a way that it is possible to perform the CaCO₃ calcination at a temperature of 950 °C with the energy transported by a hot solid stream produced in the circulating fluidised bed combustor operating at 1030 °C. The stream rich in CaO produced in the calciner is split into three parts. One of them is transported to the carbonator operating at 650 °C where most of the CO₂ in the flue gas produced in the combustor is captured. The second one is sent to the combustor, where it is heated up and used as energy carrier. The third solid stream that leaves the calciner is a purge in order to maintain the capture system activity and to avoid inert material accumulation. Because of the high temperatures involved in all the system, it is possible to recover most of the energy in the fuel and to produce power in a supercritical steam cycle. A case study is presented and it is demonstrated that under these operating conditions, 90% CO₂ capture efficiency can be achieved with no energy penalty further than the one originated in the CO₂ compression system.     

Long-term coal gasification-based power plants with near-zero emissions. Part A: Zecomix cycle

These two part papers analyse three plant configurations for high efficiency, near-zero emissions power generation from coal, suitable for long-term installations. In the first part the Zecomix cycle, a novel power plant based on various innovative processes, is presented. Zecomix plant is based on a coal hydrogasification process, using recycled steam and hydrogen as gasifying agents, to produce a CH₄ rich syngas. Methane is then converted to an H₂/H₂O based syngas and CO₂ is captured, by reacting in two carbonator reactors with CaO-based solid sorbent. CaCO₃ produced in carbonators is thermally regenerated in a calciner. The synthetic fuel is burned with oxygen in a semi-closed high temperature steam cycle, with a supercritical heat recovery.The paper presents a detailed analysis of the thermodynamic aspects of the process, with the scope of assessing its potential performance in terms of efficiency and emissions. Main operating parameters of the chemical island (e.g. hydrogasifier and calciner pressure, steam flow rates to carbonators, syngas recycle fraction) and of the power island (e.g. pressure ratio, turbine inlet temperature and reheat pressure) were varied in order to evaluate their effect on plant performance and to optimize the process. Critical issues are specifically discussed: the calcination process, the calcium oxide utilization in carbonators, the cooling requirement of the high temperature turbine, the presence of incondensable species in the steam cycle. An accurate performance estimation is therefore developed by considering advanced components, as an evolution of today's technology, excluding unproven devices whose feasibility cannot be anticipated.Depending on sorbent utilization, a net plant efficiency of 44–47% with a virtually complete carbon capture was obtained, a very interesting result with respect to other proposed coal-fired power plants with carbon capture. The high complexity of the chemical island and the importance of a good sorbent performance should be however taken into account for a fair comparison with other plant concepts. Further experimental investigations are mandatory to demonstrate the technical and economical feasibility of the Zecomix plant.     

Integration and evaluation of a power plant with a CaO-based CO2 capture system

This paper explores the integration and evaluation of a power plant with a CaO-based CO₂ capture system. There is a great amount of recoverable heat in the CaO-based CO₂ capture process. Five cases for the possible integration of a 600 MW power plant with CaO-based CO₂ capture process are considered in this paper. When the system is configured so that recovered heat is used to replace part of the boiler heat load (Case 2), modelling not only shows that this is the system recovering the most heat of 1008.8 MW but also results in the system with the lowest net power output of 446 MW and the second lowest of efficiency of 34.1%. It is indicated that system performance depends both on the amount of heat recovery and the type of heat utilization. When the system is configured so that a 400 MW power plant is built using the recovered heat (Case 4), modelling shows that this is the system with the most net power output of 846 MW, the highest efficiency of 36.8%, the lowest cost of electricity of 54.3 €/MWh and the lowest cost of CO₂ avoided of 28.9 €/tCO₂. This new built steam cycle will not affect the operation of the reference plant which vents its CO₂ to the atmosphere, highly reducing the connection between the CO₂ capture process and the reference plant which vents its CO₂ to the atmosphere. The average cost of electricity and the cost of CO₂ avoided of the five cases are about 58.9 €/kWh and 35.9 €/tCO₂, respectively.     

Life cycle assessment of a pulverized coal power plant with post-combustion capture, transport and storage of CO2

In this study the methodology of life cycle assessment has been used to assess the environmental impacts of three pulverized coal fired electricity supply chains with and without carbon capture and storage (CCS) on a cradle to grave basis. The chain with CCS comprises post-combustion CO₂ capture with monoethanolamine, compression, transport by pipeline and storage in a geological reservoir. The two reference chains represent sub-critical and state-of-the-art ultra supercritical pulverized coal fired electricity generation. For the three chains we have constructed a detailed greenhouse gas (GHG) balance, and disclosed environmental trade-offs and co-benefits due to CO₂ capture, transport and storage. Results show that, due to CCS, the GHG emissions per kWh are reduced substantially to 243 g/kWh. This is a reduction of 78 and 71% compared to the sub-critical and state-of-the-art power plant, respectively. The removal of CO₂ is partially offset by increased GHG emissions in up- and downstream processes, to a small extent (0.7 g/kWh) caused by the CCS infrastructure. An environmental co-benefit is expected following from the deeper reduction of hydrogen fluoride and hydrogen chloride emissions. Most notable environmental trade-offs are the increase in human toxicity, ozone layer depletion and fresh water ecotoxicity potential for which the CCS chain is outperformed by both other chains. The state-of-the-art power plant without CCS also shows a better score for the eutrophication, acidification and photochemical oxidation potential despite the deeper reduction of SO_x and NO_x in the CCS power plant. These reductions are offset by increased emissions in the life cycle due to the energy penalty and a factor five increase in NH₃ emissions.     

Environmental impacts of absorption-based CO2 capture unit for post-combustion treatment of flue gas from coal-fired power plant

This study assesses potential environmental impacts of the absorption-based carbon dioxide (CO₂) capture unit that is integrated to coal-fired power plant for post-combustion treatment of flue gas. The assessment was performed by identifying potential pollutants and their sources as well as amounts of emissions from the CO₂ capture unit and also by reviewing toxicology, potential implications to human health and the environment, as well as the environmental laws and regulations associated with such pollutants. The assessment shows that, while offering a significant environmental benefit through a reduction of greenhouse gas emissions, the installation of CO₂ capture units for post-combustion treatment might induce unintentional and potential burdens to human health and the environment through four emission pathways, including treated gas, process wastes, fugitive emissions, and accidental releases. Such burdens nevertheless can be predetermined and properly mitigated through a well-established environmental management program and mitigation measures. Recommendations to minimize these impacts are provided in this paper.     

Mercury measurement and control in a CO2-enriched flue gas

Oxycombustion is being considered as a promising solution to carbon capture and sequestration. Standard sampling and measurement methods may or may not be valid under oxycombustion conditions because the flue gas differs significantly from that of conventional air-blown coal combustion.Bench-scale tests were conducted to evaluate the measurement validity of continuous mercury monitors (CMMs), with and without a flue gas preconditioning unit, in a simulated oxycombustion flue gas with varied CO₂ concentrations. Tests also included mercury capture with activated carbon in typical oxyfuel combustion flue gas. Research data indicated that highly concentrated CO₂ streams affect the accuracy of the mass flow rate and the subsequent gaseous mercury measurement, although this is specific to the type of CMM. Concentrated CO₂ streams also induced solid precipitation in the wet-chemistry conversion unit and resulted in a biased measurement of the gas-phase mercury. Flue gas dilution appeared to provide accurate measurement of total gas-phase mercury and be applicable to mercury measurement in highly concentrated CO₂ streams, although mercury speciation appeared to be problematic and will require additional modification and validation. Mercury capture with activated carbon under CO₂-enriched conditions showed similar performance to typical high-acid coal combustion flue gas.     

Capture-ready coal plants—Options,technologies and economics

This paper summarizes the spectrum of options that can be employed during the initial design and construction of pulverized coal (PC), and integrated gasification and combined cycle (IGCC) plants to reduce the capital costs and energy losses associated with retrofitting for CO₂ capture at some later time in the future. It also estimates lifetime (40 year) net present value (NPV) costs of plants with differing levels of pre-investment for CO₂ capture under a wide range of CO₂ price scenarios. Three scenarios are evaluated—a baseline supercritical PC plant, a baseline IGCC plant and an IGCC plant with pre-investment for capture. This analysis evaluates each technology option under a range of CO₂ price scenarios and determines the optimum year of retrofit, if any. The results of the analysis show that a baseline PC plant is the most economical choice under low CO₂ prices, and IGCC plants are preferable at higher CO₂ prices (e.g., an initial price of about $22/t CO₂ starting in 2015 and growing at 2%/year). Little difference is seen in the lifetime NPV costs between the IGCC plants with and without pre-investment for CO₂ capture. This paper also examines the impact of technology choice on lifetime CO₂ emissions. The difference in lifetime emissions become significant only under mid-estimate CO₂ price scenarios (roughly between $20 and 40/t CO₂) where IGCC plants will retrofit sooner than a PC plant.     

CO2 capture from coal-fired power plants based on sodium carbonate slurry; a systems feasibility and sensitivity study

In this work the feasibility of a CO₂ capture system based on sodium carbonate–bicarbonate slurry and its integration with a power plant is studied. The results are compared to monoethanolamine (MEA)-based capture systems. Condensing power plant and combined heat and power plant with CO₂ capture is modelled to study the feasibility of combined heat and power plant for CO₂ capture.Environmental friendly sodium carbonate would be an interesting chemical for CO₂ capture. Sodium carbonate absorbs CO₂ forming sodium bicarbonate. The low solubility of sodium bicarbonate is a weak point for the sodium carbonate based liquid systems since it limits the total concentration of carbonate. In this study the formation of solid bicarbonate is allowed, thus forming slurry, which can increase the capacity of the solvent. With this the energy requirement of stripping of the solvent could potentially be around 3.22 MJ/kg of captured CO₂ which is significantly lower than with MEA based systems which typically have energy consumption around 3.8 MJ/kg of captured CO₂.Combined heat and power plants seem to be attractive for CO₂ capture because of the high total energy efficiency of the plants. In a condensing power plant the CO₂ capture decreases directly the electricity production whereas in a combined heat and power plant the loss can be divided between district heat and electricity according to demand.     

CO2 capture from combined cycles integrated with Molten Carbonate Fuel Cells

In this paper Molten Carbonate Fuel Cells (MCFCs) are considered for their potential application in carbon dioxide separation when integrated into natural gas fired combined cycles. The MCFC performs on the anode side an electrochemical oxidation of natural gas by means of CO₃^2? ions which, as far as carbon capture is concerned, results in a twofold advantage: the cell removes CO₂ fed at the cathode to promote carbonate ion transport across the electrolyte and any dilution of the oxidized products is avoided.The MCFC can be “retrofitted” into a combined cycle, giving the opportunity to remove most of the CO₂ contained in the gas turbine exhaust gases before they enter the heat recovery steam generator (HRSG), and allowing to exploit the heat recovery steam cycle in an efficient “hybrid” fuel cell + steam turbine configuration. The carbon dioxide can be easily recovered from the cell anode exhaust after combustion with pure oxygen (supplied by an air separation unit) of the residual fuel, cooling of the combustion products in the HRSG and water separation. The resulting power cycle has the potential to keep the overall cycle electrical efficiency approximately unchanged with respect to the original combined cycle, while separating 80% of the CO₂ otherwise vented and limiting the size of the fuel cell, which contributes to about 17% of the total power output so that most of the power capacity relies on conventional low cost turbo-machinery. The calculated specific energy for CO₂ avoided is about 4 times lower than average values for conventional post-combustion capture technology. A sensitivity analysis shows that positive results hold also changing significantly a number of MCFC and plant design parameters.     

Thermodynamic analysis on post-combustion CO2 capture of natural-gas-fired power plant

A chemical absorption, post-combustion CO₂ capture unit is simulated and an exergy analysis has been conducted, including irreversibility calculations for all process units. By pinpointing major irreversibilities, new proposals for efficient energy integrated chemical absorption process are suggested. Further, a natural-gas combined-cycle power plant with a CO₂ capture unit has been analyzed on an exergetic basis. By defining exergy balances and black-box models for plant units, investigation has been made to determine effect of each unit on the overall exergy efficiency. Simulation of the chemical absorption plant was done using UniSim Design software with Amines Property Package. For natural-gas combined-cycle design, GT PRO software (Thermoflow, Inc.) has been used. For exergy calculations, spreadsheets are created with Microsoft Excel by importing data from UniSim and GT PRO. Results show the exergy efficiency of 21.2% for the chemical absorption CO₂ capture unit and 67% for the CO₂ compression unit. The total exergy efficiency of CO₂ capture and compression unit is 31.6%.     

Evaluation of different CHP options for refinery integration in the context of a low carbon future

This study presents a comparison of different concepts for delivering combined heat and power (CHP) to a refinery in Norway. A reference case of producing high pressure steam from natural gas in boilers and electricity in a combined cycle power plant, is compared to a: (1) natural gas fueled CHP without any CO₂ capture; (2) hydrogen fueled CHP with hydrogen produced from steam methane reforming (SMR); (3) hydrogen fueled CHP with hydrogen produced from autothermal reforming (ATR); and finally (4) natural gas fueled CHP with postcombustion CO₂ removal. The options are compared on the basis of first law efficiency, emissions of CO₂ and a simplified cash flow evaluation. Results show that in terms of efficiency the standard natural gas fueled CHP performs better than the reference case as well as the options with carbon capture. The low carbon options in turn offer lower emissions of greenhouse gases while maintaining the same efficiency as the reference case. The cash flow analysis shows that for any option, a certain mix of prices is required to produce a positive cash flow. As expected, the relationship between natural gas price and electricity price affects all options. Also the value of heat and CO₂ emissions plays an important role.     

A novel process integration,optimization and design approach for large-scale implementation of oxy-fired coal power plants with CO2 capture

The widespread use of fossil fuels within the current energy infrastructure is considered as the largest source of anthropogenic emissions of carbon dioxide, which is largely blamed for global warming and climate change. At the current state of development, the risks and costs of non-fossil energy alternatives, such as nuclear, biomass, solar, and wind energy, are so high that they cannot replace the entire share of fossil fuels in the near future timeframe. Additionally, any rapid change towards non-fossil energy sources, even if possible, would result in large disruptions to the existing energy supply infrastructure. As an alternative, the existing and new fossil fuel-based plants can be modified or designed to be either “capture” or “capture-ready” plants in order to reduce their emission intensity through the capture and permanent storage of carbon dioxide in geological formations. This would give the coal-fired power generation units the option to sustain their operations for longer time, while meeting the stringent environmental regulations on air pollutants and carbon emissions in years to come.Currently, there are three main approaches to capturing CO₂ from the combustion of fossil fuels, namely, pre-combustion capture, post-combustion capture, and oxy-fuel combustion. Among these technology options, oxy-fuel combustion provides an elegant approach to CO₂ capture. In this approach, by replacing air with oxygen in the combustion process, a CO₂-rich flue gas stream is produced that can be readily compressed for pipeline transport and storage. In this paper, we propose a new approach that allows air to be partially used in the oxy-fired coal power plants. In this novel approach, the air can be used to carry the coal from the mills to the boiler (similar to the conventional air-fired coal power plants), while O₂ is added to the secondary recycle flow as well as directly to the combustion zone (if needed). From a practical point of view, this approach eliminates problems with the primary recycle and also lessens concerns about the air leakage into the system. At the same time, it allows the boiler and its back-end piping to operate under slight suction; this avoids the potential danger to the plant operators and equipment due to possible exposure to hot combustion gases, CO₂ and particulates. As well, by integrating oxy-fuel system components and optimizing the overall process over a wide range of operating conditions, an optimum or near-optimum design can be achieved that is both cost-effective and practical for large-scale implementation of oxy-fired coal power plants.     

Use of experience curves to estimate the future cost of power plants with CO2 capture

Given the dominance of power plant emissions of greenhouse gases, and the growing worldwide interest in CO₂ capture and storage (CCS) as a potential climate change mitigation option, the expected future cost of power plants with CO₂ capture is of significant interest. Reductions in the cost of technologies as a result of learning-by-doing, R&D investments and other factors have been observed over many decades. This study uses historical experience curves as the basis for estimating future cost trends for four types of electric power plants equipped with CO₂ capture systems: pulverized coal (PC) and natural gas combined cycle (NGCC) plants with post-combustion CO₂ capture; coal-based integrated gasification combined cycle (IGCC) plants with pre-combustion capture; and coal-fired oxyfuel combustion for new PC plants. We first assess the rates of cost reductions achieved by other energy and environmental process technologies in the past. Then, by analogy with leading capture plant designs, we estimate future cost reductions that might be achieved by power plants employing CO₂ capture. Effects of uncertainties in key parameters on projected cost reductions also are evaluated via sensitivity analysis.     

Design and off-design analyses of a pre-combustion CO2 capture process in a natural gas combined cycle power plant

In this study, a cycle designed for capturing the greenhouse gas CO₂ in a natural gas combined cycle power plant has been analyzed. The process is a pre-combustion CO₂ capture cycle utilizing reforming of natural gas and removal of the carbon in the fuel prior to combustion in the gas turbine. The power cycle consists of a H₂-fired gas turbine and a triple pressure steam cycle. Nitrogen is used as fuel diluent and steam is injected into the flame for additional NO_x control. The heat recovery steam generator includes pre-heating for the various process streams. The pre-combustion cycle consists of an air-blown auto-thermal reformer, water–gas shift reactors, an amine absorption system to separate out the CO₂, as well as a CO₂ compression block. Included in the thermodynamic analysis are design calculations, as well as steady-state off-design calculations. Even though the aim is to operate a plant, as the one in this study, at full load there is also a need to be able to operate at part load, meaning off-design analysis is important. A reference case which excludes the pre-combustion cycle and only consists of the power cycle without CO₂ capture was analyzed at both design and off-design conditions for comparison. A high degree of process integration is present in the cycle studied. This can be advantageous from an efficiency stand-point but the complexity of the plant increases. The part load calculations is one way of investigating how flexible the plant is to off-design conditions. In the analysis performed, part load behavior is rather good with efficiency reductions from base load operation comparable to the reference combined cycle plant.