Molecular Structure and Crystallization Dynamics of Poly(3-hydroxyl alkanoate) with Medium-Chain Length Biosynthesized from <Emphasis Type="Italic">Pseudomonas putida</Emphasis>

The molecular structure of poly(3-hydroxyalkanoate) (P3HA) with medium-chain length, biosynthesized from Psuedomonas putida (P. putida), was investigated by thermal analysis, X-ray diffraction, and infrared spectrum. Cultivation in a medium of nonanoic acid and a mixed substrate of nonanoic acid and glycerin as carbon sources provided P3HA with monomer units of 7 and 9 carbons (P3HA_n) and 5, 6, 7, 8, 9, and 10 carbons (P3HA_mix). Since these P3HA has comparatively long side chains, the crystallinity was as low as about 10%. It was suggested that the hydrogen bonding plays an important role in constructing the crystal. The lamellar thickness was 1.20 nm, estimated from the melting temperature depression. This lamellar thickness corresponds to two repeating units. Crystallinity depending on time was observed by the CO stretching mode in the infrared spectrum, and then Avrami’s theory was applied to analyze the crystallization mechanism. The crystallization rate of P3HA_n was very low, on the order of a few hours. An Avrami exponent of 1.45 was estimated from the slope of the Avrami plot. This shows that the conformational arrangement is presumably promoted along the chain axis. The slow crystallization is attributed to the long side chain, which prevents aggregation of the polymer chains.     

Biomass Carbon Ratio of Polymer Composites Measured by Accelerator Mass Spectrometry

The evaluation method of biomass carbon ratio of polymer composite samples including organic and inorganic carbons individually was investigated. Biodegradable plastics and biobased plastics can have their mechanical properties improved by combining with inorganic fillers. Polymer composites consisting of biodegradable plastics and carbonate were prepared by two different methods. Poly(lactic acid) (PLA) composite was prepared by synthesis from l-lactide with catalyst and calcium carbonate (CaCO₃) powders from lime. Poly(butylene succinate) (PBS) composite was prepared by hot-pressing the mixture of PBS powder and CaCO₃ powders from oyster shells. The mechanical properties of composite samples were investigated by a tensile test and a compression test using an Instron type mechanical tester. Tensile test with a dumbbell shape specimen was performed for PBS composite samples and compression test with a column shape specimen for PLA composite samples. Strength, elastic modulus and fracture strain were obtained from the above tests. Biomass carbon ratio is regulated in the American Standards for Testing and Materials (ASTM). In ASTM standards on biomass carbon ratio, it is required that carbon atoms from carbonates, such as CaCO₃, are omitted. Biomass carbon ratio was evaluated by ratio of ¹⁴C to ¹²C in the samples using Accelerator Mass Spectrometry (AMS). The effect of pretreatment, such as oxidation temperature and reaction by acid, on results of biomass carbon ratio was investigated. Mechanical properties decrease with increasing CaCO₃ content. The possibility of an evaluation method of biomass carbon ratio of materials including organic and inorganic carbons was shown.     

High Toughness and Fast Crystallization Poly(Lactic Acid)/Polyamide 11/SiO<Subscript>2</Subscript> Composites

A poly(lactic acid) (PLA)/polyamide 11 (PA11)/SiO₂ composite was mixed from PLA, PA11, and nanosilica particles through twin-screw extrusion. The PLA/PA11/SiO₂ composite was evaluated with tensile and Izod impact tests, light transmission and haze measurement, and isothermal and nonisothermal crystallization behavior determinations. The PLA/PA11/SiO₂ (97.0/3.0) composite had approximately 10.8% less ultimate tensile strength than neat PLA, but it had greater ductility and approximately ninefold greater elongation at break. A dimple morphology was observed on the fractural surface of the PLA/PA11/SiO₂ composite, indicating that the incorporation of PA11 and nanosilica particles increased the ductility of the PLA matrix. PLA with less than 3 wt% of PA11 and 0.5 phr of nanosilica particles had an Izod impact strength of 8.72 kJ/m². PA11 and nanosilica particles effectively toughened this PLA polymer; they accelerated both isothermal and nonisothermal crystallization rates and increased the crystallinities of the resulting composites under isothermal and nonisothermal crystallization processes.     

Effects of Modified Starch and Different Molecular Weight Polyvinyl Alcohols on Biodegradable Characteristics of Polyvinyl Alcohol/Starch Blends

The common biodegradable properties of polymer make them an excellent pair for blending, and the water solubility of polyvinyl alcohol (PVA) makes it easy to mix evenly with the starch. In this study, PVAs with different molecular weights were blended with various compositions of cross-linked starch (CLS) to explore the effects of molecular weight of PVA on the biodegradable characteristics of the PVA/starch blends. Comparing the biodegradability of all the various PVA/starch blends, a PVA was singled out from the PVA/starch blends of higher biodegradability. Further, the chosen PVA was then blended with the acid-modified starch (AMS) to systematically investigate the effects of the modified processing of starch on the biodegradable characteristics of the PVA/starch blends. Differential scanning calorimetry (DSC) analysis of PVA and PVA/starch specimens reveal that the T_m values of PVA/starch specimens reduce gradually as their CLS or AMS contents increase. After the CLS is blended in PVAs of different molecular weights, the tensile strength (??_f) and elongation at break (??_f) values of (P₁₀₀S₀)G₂₀M₁ specimen increase and simultaneously reduce, respectively, as their molecular weights of PVA increase from about 80,000 (PVA_BF-17) to 120,000 (PVA_BF-26). The ??_f and ??_f values of the PVA/modified-starch blends decrease with an increase in the modified starch contents. The ??_f values of the PVA/AMS specimens decrease with an increase in the concentrations of hydrochloric acid. Comparing the ??_f values of the PVA/CLS specimens with those of the PVA/AMS specimens, the ??_f values of the PVA/CLS specimens are better than those of the PVA/AMS specimens. On the contrary, the ??_f values of the PVA/AMS specimens are better than those of the PVA/CLS specimens. According to the biodegradability of all the PVA/starch blends, PVA with higher molecular weights displays higher biodegradability. The biodegradability of the PVA/modified-starch blends increase as the modified starch contents of the PVA/modified-starch blends increase. As evidenced by the results of the biodegradability test, the biodegradability of the PVA/modified-starch blends, therein PVA is blended with 1N AMS, shows better biodegradability. The result of bio-reaction kinetics experiment can evaluate the decomposition tendency of the PVA/starch blends up to any biodegradable rate under ambient environment. Using the kinetic model of the first order reaction, it is estimated that 16.20?years and 12.47?years will be needed for the PVA_BF-17/starch blends, containing 20 and 40% of CLS respectively, to be degraded up to 70% under ambient environment. In addition, it is 1.68?years for the PVA_BF-26 blends with the 40% 2N AMS under decomposition environment while it is 1.94?years for the 40% 1N AMS. Overall, the decomposition potential of PVA/AMS specimens is better than PVA/CLS specimens. Furthermore, the 1N(26P₆₀AS₄₀)₁₀₀G₂₀M₁ specimen is coincidence the biodegradable material criteria of Environmental Protection Administration (EPA) of Taiwan.     

Preparation and Properties of a Chitosan–Hyaluronic Acid-Polypyrrole Conductive Hydrogel Catalyzed by Laccase

Electro conductive hydrogels, consisting of chitosan (CS), hyaluronic acid (HA), and polypyrrole (PPy), were prepared via an in situ enzymic polymerization of pyrrole in the CS–HA hydrogel, using laccase as the catalyst. This CS–HA–PPy composite hydrogel showed good conductivity. The chemical structure and morphology of this conductive hydrogel were studied by Fourier transform infrared spectroscopy, scanning electron microscopy, and X-ray diffraction technique. For CS–HA–PPy and CH–HA hydrogel, the temperature at which fastest decomposition occurred was 260 and 244 °C, respectively. That means the thermal stability of CS–HA–PPy is better than CS–HA hydrogel. The conductive hydrogel also showed excellent swelling and deswelling behaviors.     

Suspension Polymerization of Poly(l-lactide-co-p-dioxanone) in Supercritical Carbon Dioxide

Biodegradable copolymers of l-lactide(l-LA) and p-dioxanone(PDO) were synthesized in supercritical carbon dioxide (scCO₂) with stannous octoate as the ring-opening catalyst and a fluorocarbon polymer surfactant as an stabilizer. Fine powderous products were achieved when more than 90% (w/w) l-LA was fed. Scanning electron micrographic images and laser diffraction particle size analysis of the products showed the mean diameter of particles greatly increased as the content of PDO increased. The obtained polymers had the number-average molecular weights ranging from 15,000 to 26,000 g mol⁻¹ (polydispersity index ranging from 1.3 to 2.1) according to the gel permeation chromatography measurements. The polymer structure was characterized by NMR spectroscopy, indicating the formation of copolymers. Thermal properties of the obtained polymers investigated using differential scanning calorimetry showed that the morphology of products was directly relevant to the crystallinity of the copolymers. The polymerization of l-LA and PDO copolymers in scCO₂ is also proposed as a novel production technique for high-purity, biodegradable polymers.     

Poly(Lactic Acid)-co-Aspartic Acid Copolymers: Possible Utilization in Drug Delivery Systems

The synthesis and characterization of poly(lactic acid)-co-aspartic acid copolymers (PLA-co-Asp) were presented. Subsequently, the synthesized PLA-co-Asp copolymers were tested as biodegradable carriers in drug delivery systems. PLA-co-Asp copolymers were synthesized by solution polycondensation procedure, using different molar ratios PLA/l-aspartic acid (2.33/1, 1/1, 1/2.33), manganese acetate and phosphoric acid as catalysts and N,N′-dimethyl formamide (DMF)/toluene as solvent mixture. The copolymers were characterized by FT-IR and ¹H-NMR spectroscopy, gel permeation chromatography (GPC), DSC and TG-DTG analyses. Diclofenac sodium, a non steroidal anti-inflammatory drug was subsequently loaded into PLA-co-Asp copolymers. The in vitro drug release experiments were done by dialysis of the copolymer/drug systems, in phosphate buffer solution (pH = 7.4, at 37 °C) and monitored by UV spectroscopy.     

A Synthetic Filter Material Containing Nutrients for Biofilter

In this study, a synthetic filter material with nutrients (PVA/peat/KNO₃ composite bead) was developed for biofilteration. The optimal preparing condition was each of the peat and PVA aqueous solutions mixed with 6.4 g KNO_3, and the minimum nitrogen content in the boric and phosphate aqueous solutions was 3.94 and 1.52 g-N/l, respectively. The equilibrium amount of inorganic nitrogen extracted by leaching from the prepared composite bead was between 7.95 and 8.21 mg N/g dry solid. The path of inorganic nitrogen extracted by leaching was the inorganic nitrogen dispersed in the peat phase firstly diffused into the outer PVA phase and then it diffused out of the bead surface for the A-type bead; and that was the inorganic nitrogen dispersed in both the peat and PVA phases simultaneously diffuses into the outer PVA phase and out of the bead surface, respectively, for the H-type bead. The microbial growth rate k _g of the H-type composite bead was higher than that of the A-type composite bead about 1.09–1.58 times, and the maximum value of k _g was at the H-type composite bead immersed in 0.384 M KNO₃ aqueous solution. The percentage of removed VOCs retained at more than 98% during the biofilter operating 230 days as the composite bead immersed in KNO₃ aqueous solution before packing. This composite bead bed was without the further addition of nutrients during the operating period.     

制备条件对Mn-Fe/TiO2催化剂低温脱硝性能的影响

通过浸渍法制备了一系列Mn-Fe/TiO2催化剂,并采用XRD技术对其进行了表征,考察了锰前体种类、负载量（活性组分质量占载体质量的百分比）、Fe含量（Fe物质的量占活性组分物质的量的百分比）、焙烧温度等因素对催化剂低温选择性催化还原NO性能的影响。实验结果表明：以乙酸锰为前体制备的催化剂的脱硝活性明显高于以硝酸锰为前体制备的催化剂;负载量的增加有利于脱硝活性的提高,而Fe的添加对提高催化剂的活性有重要作用,但Fe含量超过15%后,对催化剂脱硝性能的影响并不明显;焙烧温度超过650 ℃时会使活性组分的结晶度提高,导致脱硝活性的降低。在锰前体为乙酸锰、负载量为15%、Fe含量为15%、焙烧温度为500 ℃、焙烧时间为6 h、反应温度为200 ℃的条件下,Mn-Fe/TiO2催化剂的NO转化率约为95%。     

Influence of Polyol Plasticizers on the Properties of Polyvinyl Alcohol Films Fabricated by Melt Processing

In this work, high-alcoholysis polyvinyl alcohol (PVA) films were fabricated by melt processing and the plasticizing effect of compound polyol plasticizers on PVA were investigated with X-ray diffraction (XRD), differential scanning calorimetry (DSC), rheological measurements, mechanical tests etc. Hydrogen bonding interactions occurred between PVA and plasticizer. With the increase of plasticizer, the flowability of PVA was improved and reached the maximum value at the plasticizer of 20%. Glass transition temperature (T _g) and melting point (T _m) decreased with the increase of plasticizer content. For the heterogeneous nucleation effect of plasticizer, new polymorph of PVA formed. The viscosity was sensitive to the shear rates. The incorporation of plasticizers into PVA resulted in the increase of elongation at break and impact strength, as well as the decrease of tensile strength.     

Fabric-filter-supported catalyst for removal of harmful solid and gaseous compounds in municipal waste incinerator exhaust gas: characteristics of NO x reduction

We have investigated a fabric-filter-supported catalyst for removing harmful solid and gaseous compounds simultaneously from municipal incinerator exhaust gas. We studied the ways in which the efficiency of NO _x removal is influenced by filter temperature, gas flow rate, and catalyst content. The reduction of the catalyst content by mechanical reverse washing was investigated, and the state of the catalyst supported in the fabric filter was also observed using a scanning electron microscope. The catalyst supported by the fabric filter showed a removal efficiency above 75% when the filter temperature was 200°C, the gas flow rate was 1 m/min, and the catalyst content of the fabric filter was above 300 g/m². The catalyst was supported uniformly on the fibers of the fabric filter, and fine catalyst particles remained on the fibers after mechanical reverse washing. Received: October 15, 1997 / Accepted: March 19, 1999     

Ring-Opening Polymerization of Cyclic Esters onto Liquefied Biomass

Ring-opening polymerization of cyclic esters (-caprolactone, -valerolactone, and l-lactide) onto liquefied biomass (LB) was conducted to obtain the polyester-type polyol and to regulate the characteristics of LB. IR and ¹H-NMR spectra of the obtained polyol showed that the polymerization was successfully conducted in the presence of acid catalyst, which is used in liquefaction. The molecular weight (M_w), hydroxyl value, and viscosity were controllable by changing the reaction conditions. Polyester-type polyurethane foams with a wide range of properties were prepared from the obtained polyol with the appropriate combinations of foaming agents.     

Poly(vinyl alcohol)/Compost Composites for Biofiltration of Swine Waste Volatiles

In this study, a Poly(vinyl alcohol)(PVA)/compost composite bead is prepared and is indicated suitable as a filter material for biofiltration. The optimal preparation process is with the compost size of 16–35 mesh, the ratio of water to compost of 40 g/15 g compost, and the immersion time in the phosphate solution of 60 min. The composite bead prepared by this process is a porous spherical particle with a diameter between 2.4 and 6.0 mm and a density of 0.96 g/cm³. It contains 9.43 mg P/g dry solid and 12.1 mg N/g dry solid. The equilibrium moisture content of the composite bead bed from adsorption and holding experiments is 50.5 and 54.6% on a wet basis respectively, which is about 1.74 times higher than that of swine manure compost bed. It corresponds to the optimal filter material required and is sufficient to sustain biological activity as the composite bead adsorbs equilibrium moisture. The bulk compressive strength of the composite bead bed is about 1.15 times larger than that of swine manure compost bed to ensure even distribution of air flow and reduce the head loss as the air flow stream passed through. The pH value of the filter bed could maintain in the 6.9–7.2 range during the operation period due to the composite bead has the phosphate buffer capacity. The percentage of ethyl acetate removal could remain at over 99% for 40 days operation while the composite beads adsorbed inorganic nitrate nutrients. The pressure drop of two kind composite beads and pig manure compost filter beds are 0 and 2 mm H₂O, respectively, after operating for 40 days.     

Properties of Poly(Vinyl Alcohol)/Chitosan Nanocomposite Films Reinforced with Oil Palm Empty Fruit Bunch Amorphous Lignocellulose Nanofibers

The objective of this study was to investigate the properties of poly(vinyl alcohol)/chitosan nanocomposite films reinforced with different concentration of amorphous LCNFs. The properties analyzed were morphological, physical, chemical, thermal, biological, and mechanical characteristics. Oil palm empty fruit bunch LCNFs obtained from multi-mechanical stages were more dominated by amorphous region than crystalline part. Varied film thickness, swelling degree, and transparency of PVA/chitosan nanocomposite films reinforced with amorphous part were produced. Aggregated LCNFs, which reinforced PVA/chitosan polymer blends, resulted in irregular, rough, and uneven external surfaces as well as protrusions. Based on XRD analysis, there were two or three imperative peaks that indicated the presence of crystalline states. The increase in LCNFs concentration above 0.5% to PVA/chitosan polymer blends led to the decrease in crystallinity index of the films. A noticeable alteration of FTIR spectra, which included wavenumber and intensity, was obviously observed along with the inclusion of amorphous LCNFs. That indicated that a good miscibility between amorphous LCNFs and PVA/chitosan polymer blend generated chemical interaction of those polymers during physical blending. Reinforcement of PVA/chitosan polymer blends with amorphous LCNFs influenced the changes of T_g (glass transition temperature), T_m (melting point temperature), and T_max (maximum degradation temperature). Three thermal phases of PVA/chitosan/LCNFs nanocomposite films were also observed, including absorbed moisture evaporation, PVA and chitosan polymer backbone structural degradation and LCNFs pyrolysis, and by-products degradation of these polymers. The addition of LCNFs 0.5% had the highest tensile strength and the addition of LCNFs above 0.5% decreased the strength. The incorporation of OPEFB LCNFs did not show anti-microbial and anti-fungal properties of the films. The addition of amorphous LCNFs 0.5% into PVA/chitosan polymer blends resulted in regular and smooth external surfaces, enhanced tensile strength, increased crystallinity index, and enhanced thermal stability of the films.     

Crystal and Thermal Properties of PLLA/PDLA Blends Synthesized by Direct Melt Polycondensation

We herein report the effects of the component ratio and method of blending on the synthesis of stereocomplex poly(lactic acid) (SC-PLA) based on poly(l-lactic acid) (PLLA) and poly(d-lactic acid) (PDLA) prepolymers. PLLA and PDLA were prepared by direct melt polycondensation of lactic acid (DMP). Combined with the dual catalyst system, PLA prepolymers with M_w more than 20,000 were prepared by DMP. PLLA was mixed by powder blending or melt blended with PDLA. It is revealed that melt-point and spherulite growth rate of SC-PLA is strongly dependent on the perfection of SC structure. The melt point of PLA can be increased by nearly 50 °C because of the particular strong intermolecular interaction between PLLA and PDLA chains. Solid-state polycondensation (SSP) is an efficient method to increase the molecular weight of SC-PLA, but it can have a negative effect on the regularity of linear chains of SC-PLA. Thermogravimetry analyzer (TGA) results show that SC structure cannot cause the delay reaction on the thermal degradation of PLA.     

Crosslinking of Polyvinyl Alcohol (PVA) and Effect of Crosslinker Shape (Aliphatic and Aromatic) Thereof

In the presented work, the effect of crosslinker geometry on the properties of PVA is reported. The aliphatic (suberic) and aromatic (terephthalic) dicarboxylic acids are used as crosslinker molecules. On the basis of tensile test and thermal properties, it is observed that crosslinking of PVA by suberic acid is more effective than terephthalic acid. The maximum strength measured in crosslinked samples is 32.5 MPa for suberic acid crosslinked PVA which is higher than that of neat PVA (22.6 MPa). Swelling study shows that 8 h crosslinked terephthalic acid (35% w/w) samples have a minimum of 5.4% of water uptake compared to neat PVA, which dissolves readily in water. DTGA shows that the decomposition temperature of crosslinked PVA is 345?°C while neat PVA has a decomposition temperature of 315?°C. FTIR spectroscopy confirms the formation of crosslink ester bond in crosslinked PVA. The crosslinked samples kept for bio-degradation show maximum degradation in terephthalic acid (15% w/w) crosslinked PVA.     

Enhancement of Sedimentation Velocity of Heavy Metals Loaded Hydroxyapatite Using Chitosan Extracted from Shrimp Waste

In this study, synthesize hydroxyapatite (HA) suspensions sedimentation was used after usual terms as support for adsorption of heavy metals ions. Thus, the effectiveness of chitosan, produced from shrimp waste, in the flocculation of turbid suspensions resulting from the treatment of water contaminated with heavy metals was studied by adsorption on HA. Different particles sizes of HA were mainly controlled in this work (an average of granule size ranging from 1.6 to 63 μm). The results of Cu²⁺ and Zn²⁺ adsorption on HA showed relatively fast kinetics, with removal extent of 88–95 % by varying the initial total metal concentration. High removal rates were obtained for Cu²⁺. Chitosan was found to be able to eliminate by flocculation more than 98 % of turbid suspensions generated by metals adsorption on HA after only 30 min of sedimentation. Effects of pH and dose of chitosan on the coagulation–flocculation process were also studied. The optimal dose of chitosan was found between 0.2 and 2 mg/L which corresponds to an optimal pH ranging from 6 to 7.     

Biodegradation Behavior of Composite Films with Poly (Vinyl Alcohol) Matrix

The main objective of this study was to develop biodegradable, composite materials, based on poly (vinyl alcohol), bacterial cellulose and chitosan for possible application in packaging industry. Two composite materials were prepared, one containing poly (vinyl alcohol) (PVA) and bacterial cellulose (BC), named PVA/BC, and the other containing PVA, BC but also chitosan (CTS), named PVA/BC/CTS. The biodegradation behavior was studied in a fed-batch bioreactor, in aerobic and anaerobic conditions, using activated sludge. Biodegradation tests were based on weight loss measurements. Structural changes were confirmed by Fourier transform infrared spectroscopy (FTIR) and the morphological ones by scanning electron microscopy (SEM). After 4?weeks, the biodegradation experiments have shown a relative high degradation of the PVA/BC/CTS film compared with the PVA/BC one. These results were confirmed by spectral analysis and also by SEM images. Besides, the SEM images revealed that biodegradation occurs also inside the composite materials, not only on the surface.     

Synthesis and Characterization of a Thin-Film Composite Nanofiltration Membrane Based on Polyamide-Cellulose Acetate: Application for Water Purification

Membrane separation has been widely used for various applications including microfiltration (MF), ultrafiltration (UF), and nanofiltration (NF) processes in the fields of biomedicine, food, and water purification. In this work, a facile synthesis of new polyamide thin-film composite nanofiltration membranes (NF-TFC) for water purification was described. The polyamide thin film was deposed over a synthetic cellulose acetate (CA) support by interfacial polymerization method. 1,3 cyclohexane bis (methylamine) (CHMA) and trimesoyl chloride (TMC) were used as monomers. The membranes were characterized using Scanning Electron Microscopy (SEM), Fourier Transform Infrared spectroscopy (FT-IR), water uptake, porosity, contact angle, water permeability and rejection towards specific salt and dye molecules. The effect of the variation of the CHMA concentration (0.2–2 wt.%) on the morphology, porosity, water permeation and rejection properties of the prepared membranes was studied. SEM results displayed the growth of the membrane thickness when the CHMA concentration increased from 0.2 to 2 wt.%. The strong adhesion between the cellulose acetate substrate and the polyamide layer explained by the formation of the polyamide film in the substrate surface and inside the pores. The water permeability varied from 36.02 to 17.09 L h^?1 m^?2 bar^?1. The salt rejection of Na₂SO₄ and NaCl increased from 9 to 68% and from 38.41% to 89.4%, respectively, when the CHMA concentration was changed from 0.2 to 2 wt.%. The prepared membranes were further applied successfully for the removal of malachite green and congo red. The results indicated that the maximum rejection reached 89% and 85% for malachite green and congo red, respectively.

     

Fluorescence excitation-emission matrix combined with regional integration analysis to characterize the composition and transformation of humic and fulvic acids from landfill at different stabilization stages

Fluorescence excitation-emission matrix spectroscopy (EEMs) combined with fluorescence regional integration (FRI) analysis was used to investigate the composition and transformation of humic acid (HA) and fulvic acid (FA) from landfill. The EEMs of HAs at different landfill ages were characterized by two typical fluorescence chromophores with Ex/Em pairs at Ex = 420-470 nm/Em = 490-530 nm and Ex = 345-375 nm/Em = 450-465 nm. EEMs of FA were featured by other two distinctly different fluorophores with Ex/Em pairs at Ex = 315-335 nm/Em = 420-440 nm and Ex = 255-275 nm/Em = 425-455 nm. The results show that HA extracted from the refuse disposed in the year of 1989 was formed by connecting small-condensed aromatic structures with protein-like chains. Compared with HA extracted from the refuse disposed in the year of 1992, HA extracted from the refuse of 1996 had a higher fluorescence intensity and lower r_(B,A) (the ratio of the fluorescence intensities of peak B and peak A) value. It contained low molar mass components, low aromatic condensation degree, and more easily oxidized substituents. This indicates that the landfill time strongly affects the EEMs characteristics of HA, and that the humification degree of HA increases with the landfill time. A red shift to a longer wavelength region and an increase of fluorescence intensity were observed when the concentration of HA was increased, suggesting that concentration had a great influence on the fluorescence characteristics of HAs. pH (2-12) also had significant effects on the fluorescence intensity, although it exerted no effect on the peak position of fluorescence of HA and FA. The results of FRI show that increasing concentration lead to more interactions among various structure components and that small molecular weight units tend to aggregate or be masked into more complicated and larger structures. The pH influence on the fluorescence intensity of HA seems mainly through molecular configuration, while the fluorescence intensity change with pH may be due to various substituents of FA.