Tuning the surfaces of palladium nanoparticles for the catalytic conversion of Cr(VI) to Cr(III)

This work reports the feasibility of using Pd nanoparticles as innovative catalysts in the conversion of reducible contaminants from toxic to benign forms. Cr(VI) is a known carcinogen while the trivalent chromium salts are believed to be non-toxic. The ability of Pd nanoparticles to catalyze the rapid reduction of Cr(VI) to Cr(III) using reactive sulfur intermediates produced in situ was therefore studied. Using a microchamber set at 130 degrees C, the reduction mixture consists of palladium nanoparticles and sulfur (PdNPs/S), which generated highly reducing sulfur intermediates that effected the reduction of Cr(VI) to Cr(III) by 1st order reaction kinetics. UV-visible spectroscopy and cyclic voltammetry were employed to monitor the reduction process. The results showed that 99.8% of 400 microM Cr(VI) was reduced to Cr(III) by PdNPs/S in one hour compared to 2.1% by a control experiment consisting of sulfur only. The rate of Cr(VI) reduction was found to be dependent on temperature and pH and was greatly enhanced by the addition of PdNPs. Subsequent application of this approach in the reduction of Cr(VI) in soil and aqueous media was conducted. In contrast to the control experiments with and without PdNPs or sulfur, greater than 92% conversion rate was obtained in the presence of PdNPs/S within 1 hour. This represents over a 500-fold improvement in conversion rate compared to current microbial approaches. XPS analysis provided the confirmation regarding the oxidation states of Cr(VI), Cr(III) and the nature of the reactive intermediates. This work offers PdNPs/S as a new interface for the reduction of high oxidation state heavy metal pollutants.     

Speciative determination of Cr (III) and Cr (VI) in dyeing waste water of Dil Creek discharge to Izmit Gulf (Izmit-Kocaeli, Turkey) by ICP-AES

Wastewater pollution in industrial areas is one of the most important environmental problems. Heavy metal pollution, especially chromium pollution in wastewater sources from dyeing and tannery has affected the life on earth. This pollution can affect all ecosystems and human health directly or by food chain. Therefore, the determination of chromium in this study is of great importance. Dil Creek is located in the eastern Marmara region and discharges into the Izmit Gulf. This water source is used for irrigation in agriculture and as drinking water for animals. In this study, a rapid, sensitive and selective method for the speciative direct determination of Cr (III) and Cr (VI) in dyeing waste water samples collected from the nearest station to Izmit Gulf of Dil Creek in May 2006 by inductively coupled plasma-atomic emission spectrometry (ICP-AES) has been developed. An analysis of a given sample is completed in about 15 min for ICP-AES the method. As the result of the chromium analysis, the limit of quantification (LOQ) for the Cr (III), Cr (VI) and total Cr were founded as 0.0111 ± 0.0002 mg/l (RSD, 1.80%), 0.0592 ± 0.0010 mg/l (RSD, 1.70%) and 0.0703 ± 0.0020 mg/l (RSD, 2.84%) respectively. In addition, the general mathematical formula has been developed to calculate the concentration of Cr(III), which can be applied to any other metal species. The result of Cr (VI) analysis indicated that water quality of Creek was IV. class quality according to the inland water classification. In order to validate the applied method, recovery studies were performed.     

Preconcentration and speciation of Cr(III) and Cr(VI) in water and soil samples by spectrometric detection via use of nanosized alumina-coated magnetite solid phase

A novel nanomaterial has been developed for speciation of Cr(III) and Cr(VI) in water and soil samples. In this study, a new type of alumina-coated magnetite nanoparticles (Fe₃O₄/Al₂O₃ NPs) modified by the surfactant Triton X-114 has been successfully synthesized and used in magnetic mixed hemimicelles solid-phase extraction procedure. The procedure was based on the reaction of chromium(III) with 1-(2-pyridilazo)-2-naphtol as a ligand, yielding a complex, which was entrapped “in situ” in the surfactant hemimicelles. The concentration of chromium(III) was determined using flame atomic absorption spectrometry. After reduction of Cr(VI) to Cr(III) by ascorbic acid, the system was applied to the total chromium. Cr(VI) was then calculated as the difference between the total Cr and the Cr(III) content. This method can also be used for complicated matrices such as soil samples without any special pretreatment. Under the optimum conditions of parameters, the recoveries of Cr(III) by analyzing the spiked water and soil samples were between 98.6 and 100.8 % and between 96.5 and 100.7 %, respectively. Detection limits of Cr(III) were between 1.4 and 3.6 ng?mL^?1 for water samples and 5.6 ng?mg^?1 for soil samples.     

饮用水消毒副产物--卤乙酸的检测

卤乙酸是饮用水氯化消毒中一类主要的消毒副产物,由于存在的广泛性和潜在的健康危害,许多国家和卫生组织相继将其列为饮用水常规监测项目,而我国至今还没有相关规定;为了更好地控制饮用水中卤乙酸的形成,世界各国科研人员先后研究和开发出了性能逐趋完善的多种分析检测方法;本文在国内外文献调研的基础上,对卤乙酸的各种分析检测方法进行了简要的介绍,并指明了今后的发展方向.     

Multi-level modelling of chlorination by-product presence in drinking water distribution systems for human exposure assessment purposes

During drinking water treatment and distribution, chlorine reacts with organic matter occurring in water to form various chlorination by-products (CBPs) such as trihalomethanes (THMs) and haloacetic acids (HAAs). This paper presents the occurrence of THMs and HAAs in different water distribution systems (DS) of the same region and their modelling for exposure assessment purposes. This study was conducted in eight DS supplying chlorinated water to the population of Québec City, Canada. These systems differ in type of water source (i.e. surface, ground or mixed water), in treatment applied at the plant, and in size and structure of the DS. Two spatio-temporal databases for THMs and HAAs were implemented, one for model development and the other for model validation. The analysis of the data demonstrates significant seasonal and spatial variations of these compounds. A multi-level statistical modelling approach was applied to estimate the ranges for occurrence of THMs and HAAs in the eight DS (i.e. a single model for the study region for each CBP species). The modelling approach integrates available or easily measurable parameters. For both THMs and HAAs, a two-level model considering a sampling-site random effect was selected among various models initially developed. The model capacity for estimating the presence of THMs and HAAs in drinking water and its usefulness for exposure assessment purposes in the studied region was demonstrated.     

Effects of clay minerals on Cr(VI) reduction by organic compounds

The objective of this study is to examine the effect of clayminerals (illite, montmorillonite, and kaolinite) on chromate (Cr(VI)) reduction by several low molecular weightorganic compounds. Batch experiments at pH ranging from 3.0 to6.0 and 25 °C showed that 2:1 layered clays illite andsmectite catalyzed Cr(VI) reduction by oxalate. The catalyticeffect increased as pH was decreased. The 1:1 clay kaolinite hadno catalytic effect under comparable conditions. Direct Cr(VI)reduction by reactive moieties associated with illite andmontmorillonite was observed, but at a much slower rate than thecatalytic pathway. Cr(VI) reduction by glyoxylic acid, glycolicacid, lactic acid, and mandelic acid was accelerated by illite,although aqueous phase reduction might occur in parallel. Theseresults suggest that Cr(VI) reduction rates in subsurfaceenvironments rich in organic compounds may be elevated throughcatalysis of surface-bound metals and/or soluble species from theclay minerals, and as a result, higher than those expected fromaqueous phase reaction alone. Such rate enhancement for Cr(VI)reduction needs to be accounted for when developing new remedialtechniques for chromium site remediation or assessing its naturalattenuation.     

Simultaneous quantification of Bi(III) and U(VI) in environmental water samples with a complicated matrix containing organic compounds

Trace amounts of bismuth(III) and uranium(VI) can be simultaneously determined in a single scan by adsorptive cathodic stripping voltammetry in the presence of cupferron as a complexing agent. Optimal conditions were found to be: 0.1 mol?L^?1 acetate buffer (pH 5.3), 5?×?10^?5?mol?L^?1 cupferron, accumulation potential of ?0.25 V, and accumulation time of 30 s. The linear range of Bi(III) and U(VI) was observed over the concentration range from 2?×?10^?9 to 2?×?10^?7?mol?L^?1 and from 1?×?10^?8 to 5?×?10^?7?mol?L^?1, respectively. The influence of the main components of real water samples such as foreign ions and organic substances (surface active substances, humic substances) was precisely investigated. The method was applied to the simultaneous measurements of bismuth and uranium in natural water samples.     

Flow injection analysis of trace chromium (VI) in drinking water with a liquid waveguide capillary cell and spectrophotometric detection

Hexavalent chromium (Cr(VI)) is an acknowledged hazardous material in drinking waters. As such, effective monitoring and assessment of the risks posed by Cr(VI) are important analytical objectives for both human health and environmental science. However, because of the lack of highly sensitive, rapid, and simple procedures, a relatively limited number of studies have been carried out in this field. Here we report a simple and sensitive analytical procedure of flow injection analysis (FIA) for sub-nanomolar Cr(VI) in drinking water samples with a liquid core waveguide capillary cell (LWCC). The procedure is based on a highly selective reaction between 1, 5-diphenylcarbazide and Cr(VI) under acidic conditions. The optimized experimental parameters included reagent concentrations, injection volume, length of mixing coil, and flow rate. Measurements at 540 nm, and a 650-nm reference wavelength, produced a 0.12-nM detection limit. Relative standard deviations for 1, 2, and 10 nM samples were 5.6, 3.6, and 0.72 % (n?=?9), and the analysis time was <2 min sample^?1. The effects of salinity and interfering ions, especially Fe(III), were evaluated. Using the FIA-LWCC method, different sources of bottled waters and tap waters were examined. The Cr(VI) concentrations of the bottled waters ranged from the detection limit to ～20 nM, and tap waters collected from the same community supply had Cr(VI) concentration around 14 nM.     

Effect of air-drying and oven-drying treatment on Cr(VI) content and Cr bond forms in soil

Air-drying and oven-drying are pretreatment processes often used before testing and analyzing various soil characteristics in the laboratory. This study selected three kinds of soil, including red soil, entisol, and alluvial soil, and examined the variation of the Cr(VI) content and Cr bond forms in these soils during air-drying and oven-drying. The results show that when the soil is air-dried in natural environment, the Cr(VI) content decreases with air-drying time. On day 10 of air-drying, the Cr(VI) content in these soils is 22.8～47.9 % of the initial value. When the soil is oven-dried, the Cr(VI) concentration decays faster; on day 8, the Cr(VI) is no longer detected in these soil samples. When the Cr(VI)-contaminated soil is treated by air-drying and oven-drying, the Cr bond form converts into a more stable form. After oven-drying, the Cr mainly exists in Fe–Mn oxide form, organic bond form, and residual form. The air-drying and oven-drying pretreatment processes of soil reduce the Cr(VI) content and stabilize the Cr bond form. If the laboratory analytic results are applied to risk analysis or remediation strategy planning for chromium-contaminated soil, the toxicity, bioavailability, and mobility of Cr in soil may be underrated.     

Modeling nonlinearly transient zero-order bioreduction and transport of Cr(VI) in groundwater

Cr(VI) contamination of soil and groundwater is considered a major environmental concern. Bioreduction of Cr(VI) to Cr(III) can be considered a potentially effective technology in remediating Cr(VI) contaminated sites. Shewanella oneidensis MR-1 (MR-1) is one of the bacteria capable of reducing Cr(VI) to Cr(III) under anaerobic conditions. The kinetics of Cr(VI) reduction by MR-1 is defined by the dual-enzyme kinetic model which is nonlinear, transient, and zero-order. Existing transport models are not designed to simulate such reaction kinetics. The objective of this paper is to present a Petrov–Galerkin finite element model (PGFEM) to simulate transport and bioreduction of Cr(VI), by MR-1, in groundwater. The model developed is unconditionally stable and provides oscillation free accurate results for a wide range of Peclet number (Pn) and Courant number (Cn).     

二苯碳酰二肼分光光度法测定水中六价铬测量不确定度评定

根据测量不确定度评定与表示理论,采用二苯碳酰二肼分光光度法测定水中六价铬的测量不确定度,通过计算和评定,得出该法测定水中六价铬的测量结果为0.233mg/L时.取包含因子k=2(约95%置信概率),扩展不确定度U=0.007mg/L.该不确定度评价方法在实际工作中具有较强的实用价值.     

中国皮革行业六价铬排放特征分析与监管建议

在分析皮革鞣制工艺现状基础上,根据2000—2013年环境统计数据、2010—2013年国控源监督性监测数据,以及典型制革园区不同类型皮革企业的现场监测数据,分析了中国皮革行业六价铬产生与排放特征,有针对性地提出了皮革行业六价铬的监管建议。     

Survey of the occurrence of residues of methyl tertiary butyl ether (MTBE) in Dutch drinking water sources and drinking water

An indicative survey has been carried out in The Netherlands investigating the presence of methyl tertiary butyl ether (MTBE) in drinking water and the corresponding sources. In total, 71 different sites used for the preparation of drinking water in The Netherlands were sampled in two successive seasons in 2001 involving the analysis of 156 samples. (ground water (n = 88), surface water (n = 17), bank filtrate water (n = 6) and drinking water (n = 45)). To combine high sample throughput with high selectivity and sensitivity, off-line purge and trap for sampling and gas chromatography mass spectrometry equipped with an automated thermal desorption sampler (TDS-GC-MS) was selected as the preferred analytical methodology. The developed procedure enabled the analysis of at least 40 samples per day and provided a limit of quantification of 2 ng l(-1). In the first period 63 samples of raw water were analyzed. Concentrations ranged between < 10 ng l(-1) and 420 ng l(-1) with a median concentration below 10 ng l(-1). The second period was focused at the re-sampling of positive locations (MTBE > 10 ng l(-1)) and a few additional drinking water utilities of which both the raw and drinking water of the utilities were analyzed. The median concentration of MTBE in the selected set of drinking water samples was 20 ng l(-1) (n = 45). At one location MTBE was found at a level of 2900 ng l(-1) caused by point source contamination of the ground water (11 900 ng l(-1)). Special attention has been paid to the quality of the results by analyzing all samples in duplicate and the analysis of control samples during each series of analyses.     

Mechanistic studies of N-nitrosodimethylamine (NDMA) formation in chlorinated drinking water

Studies were conducted to investigate the hypothesis that N-nitrosodimethylamine (NDMA) is a potential disinfection by-product specifically produced during chlorination or chloramination. Experiments were conducted using dimethylamine (DMA) as a model precursor. NDMA was formed by the reaction of DMA with free chlorine in the presence of ammonia and also with monochloramine. We proposed a mechanism for NDMA formation in chlorinated or chloraminated water, which does not require nitrite as in N-nitrosation. The critical NDMA formation reactions consist of (i) the formation of monochloramine by combination of free chlorine with ammonia, (ii) the formation of 1,1-dimethylhydrazine (UDMH) intermediate from the reaction of DMA with monochloramine followed by, (iii) the oxidation of UDMH by monochloramine to NDMA, and (iv) the reversible chlorine transfer reaction between free chlorine/monochloramine and DMA which is parallel with (i) and (ii). A kinetic model was also developed to validate the proposed mechanism.     

Occurrence of haloacetic acids (HAAs) and trihalomethanes (THMs) in drinking water of Taiwan

In this study, water samples were collected from 86 water treatment plants for analysis of haloacetic acids (HAAs) and trihalomethanes (THMs) from February to March, 2007 and from July to August, 2007. Both seasonal and geographical variations of disinfection by-products (DBPs) in drinking water of Taiwan were presented. The results showed that the five HAA concentrations (HAA5) were 1.0–38.9 μg/L in the winter and 0.2–46.7 μg/L in the summer; and the total THMs were ND-99.4 μg/L in the winter and ND-133.2 μg/L in the summer. For samples taken from the main Taiwan island, dichloroacetic acid (29.4–31.7%) and trichloroacetic acid (25.3–27.6%) were the two major HAA species, and trichloromethane was the major THM species (49.9–62.2%) in finished water. For water treatment plants located on the offshore islands outside of Taiwan, high bromide concentration was found in raw water, and higher percentage of brominated THMs and HAAs were formed in the overall formation. A statistically significant (P?<?0.005) logarithmic linear regression model was found to be useful to describe the correlations between TTHM and HAA5 or nine HAAs (HAA5?=?1.219 ×TTHM ^0.754, R ²?=?0.658; HAA9?=?1.824 ×TTHM ^0.735, R ²?=?0.678). No apparent difference was observed for DBPs concentrations between finished water and distribution samples in this study.     

Role of halogen(I) cation-transfer mechanisms in water chlorination in the presence of bromide ion

Bromide ion is rapidly converted to HOBr via BrCl by reaction with HOCl. The subsequent slow reactions of (HOCl, OCl-)/(HOBr, OBr-) mixtures are monitored directly by multiwavelength UV-vis absorbance methods and simultaneously by ion chromatographic measurement of ClO2-, ClO3-, and BrO3- (p[H+] 5.6-7.6). A first-order loss of HOCl is observed which is catalyzed by trace concentrations of Br- and BrCl. Chlorite ion forms first and is subsequently oxidized to ClO3-. The loss of HOBr is slower and is second-order in HOBr, so that BrO3- formation takes longer than ClO3- formation. Under the conditions of this work, the relative yield of BrO3- increases with increase in pH. The decomposition of HOCI by bromide proceeds primarily by a series of halogen(I) cation-transfer reactions with subsequent halide release. The presence of HOCI increases the BrO3- yield three-fold from HOBr decay alone.     

Spectrophotometric method for the determination of chromium (VI) in water samples

A simple and sensitive spectrophotometric method for the determination of chromium has been developed. The method is based on the diazotization of Dapsone in hydroxylamine hydrochloride medium and coupling with N-(1-Napthyl) Ethylene Diamine Dihydrochloride by electrophilic substitution to produce an intense pink azo-dye, which has absorption maximum at 540 nm. The Beer's law is obeyed from 0.02-1.0 microg mL(-1) and the molar absorptivity is 3.4854 L mol(-1) cm(-1). The Limits of quantification and Limit of detection of the proposed method are 0.0012 microg mL(-1) and 0.0039 microg mL(-1) respectively. The method has been successfully applied for the determination of chromium in water samples and the results were statistically evaluated with that of the reference method.     

Using a relative health indicator (RHI) metric to estimate health risk reductions in drinking water

When a new drinking water regulation is being developed, the USEPA conducts a health risk reduction and cost analysis to, in part, estimate quantifiable and non-quantifiable cost and benefits of the various regulatory alternatives. Numerous methodologies are available for cumulative risk assessment ranging from primarily qualitative to primarily quantitative. This research developed a summary metric of relative cumulative health impacts resulting from drinking water, the relative health indicator (RHI). An intermediate level of quantification and modeling was chosen, one which retains the concept of an aggregated metric of public health impact and hence allows for comparisons to be made across “cups of water,” but avoids the need for development and use of complex models that are beyond the existing state of the science. Using the USEPA Six-Year Review data and available national occurrence surveys of drinking water contaminants, the metric is used to test risk reduction as it pertains to the implementation of the arsenic and uranium maximum contaminant levels and quantify “meaningful” risk reduction. Uranium represented the threshold risk reduction against which national non-compliance risk reduction was compared for arsenic, nitrate, and radium. Arsenic non-compliance is most significant and efforts focused on bringing those non-compliant utilities into compliance with the 10 μg/L maximum contaminant level would meet the threshold for meaningful risk reduction.     

Application of multimedia exposure assessment to drinking water

A potentially important exposure route for humans is the ingestion of chemicals via drinking water. If comprehensive exposure assessments are to be completed for either existing or proposed new chemicals and cost effective control strategies developed, then a quantitative understanding of multimedia transport and fate of specific chemical pollutants must be achieved. Mathematical models provide a powerful framework into which quantitative relationships may be placed to provide guidance in reaching water quality goals. Existing, state-of-the-art media-specific toxic organic transport and fate models for atmospheric (DiDOT), land surface (NPS) and surface water processes (EXAMS) and potable water treatment (WTP) have been linked to demonstrate the technical feasibility of such an approach. Limited application and sensitivity testing of this linked modeling system has shown that the impact of various source loadings and control strategies on drinking water quality can be estimated.