次氯酸钠湿法烟气脱硝及同时脱硫脱硝技术研究

采用NaClO作氧化吸收剂,在鼓泡反应装置进行了湿法烟气脱硝实验研究,考察了NaIO、NO浓度、液相温度、气体流量、pH对脱硝效率的影响以及SO2对同时脱硫脱硝效率的影响,并结合液相产物分析探讨了同时脱硫脱硝反应机理.研究结果表明,pH值是影响活性成分HClO存在形式的重要因素,同时也是影响氧化吸收的关键因素;在一定范...     

Characteristics of emissive spectrum and the removal of nitric oxide in N2/O2/NO plasma with argon additive

Although the approach using non-thermal plasma (NTP) for deNOx has been studied for over 15 years, how to achieve higher removal e ciency with lower cost is still a barrier for its industrial application. In order to investigate the impact of the argon additive on electron density, energy and nitric oxide reduction process in plasma, the spectrum of the dielectric barrier discharge at atmospheric pressure in a coaxial reactor was measured using the monochromater with high resolution. The comparative experiments for NO reduction were carried out simultaneously in N2/O2/NO plasma stream with and without argon, respectively. The nitrogen molecular spectrum which is attributed to the energy level transition (C3 u ! B3 g) was compared in the wavelength range 300–480 nm and the electron density and temperature were determined based on the relative intensities and Stark broadening width of spectral lines. The spectrum results indicated that the argon additive could enhance the intensity of emissive spectrum of plasma, thus the electron concentration as well as the energy was increased, and finally prompted the ionization rate to produce active N, O and O3. The results of NO reduction showed that NO conversion e ciency increased in the range of 10%–30% with 5% addition of argon in stream comparing with the condition without argon additive. This study will play a positive role in the industrial application of dielectric barrier discharge deNOx reactor.     

大气NOx测量准确性问题分析

采用美国热电公司的NO-N02-NOx分析仪(Model 42i TL)和NOy分析仪(Model 42i NOy),在2011年1月-10月期间,对北京城市大气中的NO、NOx和NOy进行了连续在线测量.两台仪器对NO的测量结果具有较高的一致性(r＞0.998,p＜0.01),说明两台仪器测量精度基本一致.将NOy分析仪(Model 42i NOy)采样口处安装和不安装颗粒物过滤膜两种条件下测量的NOy结果与NO-NO2-NOx分析仪所测的NOx结果分别进行了相关性分析([NOy] =0.989x[NOx],R2 =0.993;[NOy] =1.134 ×[NOx],R2=0.959),得出以下两个结论:①以颗粒态硝酸盐为代表的颗粒物是造成NOx与NOy偏差的主要原因,其所占比例在10％左右;②目前Model 42i-TL所测NOx的浓度水平较真实值偏高,其测量值更接近气态NOy的浓度水平.为估算NO2测值被高估的程度(以2011年8月6日-15日观测数据为例),用扣除部分气态NOz物种(HONO、HNO3、PAN、PPN)的修正方法,推论出在夏季N02被高估约7％(R2=0.968).     

Toluene decomposition performance and NOx by-product formation during a DBD-catalyst process

Characteristics of toluene decomposition and formation of nitrogen oxide (NOx) by-products were investigated in a dielectric barrier discharge (DBD) reactor with/without catalyst at room temperature and atmospheric pressure. Four kinds of metal oxides, i.e., manganese oxide (MnOx), iron oxide (FeOx), cobalt oxide (CoOx) and copper oxide (CuO), supported on Al₂O₃/nickel foam, were used as catalysts. It was found that introducing catalysts could improve toluene removal efficiency, promote decomposition of by-product ozone and enhance CO₂ selectivity. In addition, NOx was suppressed with the decrease of specific energy density (SED) and the increase of humidity, gas flow rate and toluene concentration, or catalyst introduction. Among the four kinds of catalysts, the CuO catalyst showed the best performance in NOx suppression. The MnOx catalyst exhibited the lowest concentration of O₃ and highest CO₂ selectivity but the highest concentration of NOx. A possible pathway for NOx production in DBD was discussed. The contributions of oxygen active species and hydroxyl radicals are dominant in NOx suppression.     

NO conversion by positive streamer discharge-effects of gas compositions and reaction conditions

The effects of gas compositions and reaction conditions on NO conversion by positive streamer discharge were experimentally investigated by using a link tooth wheel-cylinder reactor. The results showed that NO conversion increased with increasing O₂ concentration and NH₃ concentration, but decreased with increasing inlet NO concentration and gas flow rate. The addition of CO₂ or H₂O to the feed gas promoted NO conversion by increasing the maximum discharge voltage, and NH₄NO₃ was formed in the presence of NH₃. There was a most suitable range interval between discharge tooth wheels if both NO conversion and energy consumption were considered. Increasing applied voltage resulted in the increase in the amount of O₃ generated by streamer discharge.     

High NO2/NOx emissions downstream of the catalytic diesel particulate filter: An influencing factor study

Diesel vehicles are responsible for most of the traffic-related nitrogen oxide (NO_x) emissions, including nitric oxide (NO) and nitrogen dioxide (NO₂). The use of after-treatment devices increases the risk of high NO₂/NO_x emissions from diesel engines. In order to investigate the factors influencing NO₂/NO_x emissions, an emission experiment was carried out on a high pressure common-rail, turbocharged diesel engine with a catalytic diesel particulate filter (CDPF). NO₂ was measured by a non-dispersive ultraviolet analyzer with raw exhaust sampling. The experimental results show that the NO₂/NO_x ratios downstream of the CDPF range around 20%–83%, which are significantly higher than those upstream of the CDPF. The exhaust temperature is a decisive factor influencing the NO₂/NO_x emissions. The maximum NO₂/NO_x emission appears at the exhaust temperature of 350°C. The space velocity, engine-out PM/NO_x ratio (mass based) and CO conversion ratio are secondary factors. At a constant exhaust temperature, the NO₂/NO_x emissions decreased with increasing space velocity and engine-out PM/NO_x ratio. When the CO conversion ratios range from 80% to 90%, the NO₂/NO_x emissions remain at a high level.     

Numerical evaluation of the effectiveness of NO2 and N2O5 generation during the NO ozonation process

Wet scrubbing combined with ozone oxidation has become a promising technology for simultaneous removal of SO₂ and NO_x in exhaust gas. In this paper, a new 20-species, 76-step detailed kinetic mechanism was proposed between O₃ and NO_x. The concentration of N₂O₅ was measured using an in-situ IR spectrometer. The numerical evaluation results kept good pace with both the public experiment results and our experiment results. Key reaction parameters for the generation of NO₂ and N₂O₅ during the NO ozonation process were investigated by a numerical simulation method. The effect of temperature on producing NO₂ was found to be negligible. To produce NO₂, the optimal residence time was 1.25 sec and the molar ratio of O₃/NO about 1. For the generation of N₂O₅, the residence time should be about 8 sec while the temperature of the exhaust gas should be strictly controlled and the molar ratio of O₃/NO about 1.75. This study provided detailed investigations on the reaction parameters of ozonation of NO_x by a numerical simulation method, and the results obtained should be helpful for the design and optimization of ozone oxidation combined with the wet flue gas desulfurization methods (WFGD) method for the removal of NO_x.     

介质阻挡放电中添加乙炔对NO脱除的影响

利用介质阻挡放电(DBD)进行模拟烟气脱除NO实验,通过改变乙炔体积分数和烟气水蒸汽含量研究添加乙炔对NO脱除效率的影响.结果表明:烟气中添加乙炔强化了NO氧化作用,随着乙炔体积分数的提高,NO脱除率逐渐增加.在NO/N2/O2/C2H2/H2O体系中,水的电负性和离解反应消耗大量高能电子,降低了活性自由基的生成,NO脱除速率随之减慢;能量密度低于400 J·L-1时,相对湿度(RH)为0的情况下脱出效果最好.但随着能量密度的增加,H2O不会影响最终的NO脱除率;H2O的添加可以产生更多的·OH自由基,促进NO2向HNO3转化,使出口NO2浓度大幅度降低.     

非热等离子体结合CuO催化剂或Ca(OH)2吸收剂去除氮氧化物

采用非热等离子体结合催化或现场化学吸收的2种方法来去除气流中的NO_x.结果表明,非热等离子体结合催化,反应器内的CuO催化剂能有效地促进NO的还原反应;相对于催化还原NO而言,脉冲电晕作用下能有效地降低NO催化还原的反应温度.当催化剂为CuO,脉冲电压为18kV,反应温度为200℃,还原剂为1%CO及NO进口浓度为719 mg/m³条件下,NO的去除率达到了100%.非热等离子体结合现场化学吸收方法,是一种在常温下从气流中净化氮氧化物的有效方法,NO的去除率远远高于反应器内没有吸收剂的情况.可以认为反应器内的Ca(OH)₂吸收剂通过与NO的氧化产物NO₂或NO₃的吸收反应促进了NO的去除.当反应器内有Ca(OH)₂吸收剂存在时,在脉冲电压为18kV,O₂浓度为2%及NO进口浓度为1 050 mg/m³条件下,NO的去除率达到了100%.     

The evaluation of some photochemical smog reaction mechanisms—III. Dilution and emissions effects

The effects of dilution and emissions on the performance of four widely-used photochemical smog reaction mechanisms are examined, using newly available experimental data from the CSIRO outdoor smog chambers. It is found that the Caltech, CB-XR and CB-IV mechanisms overpredicted the smog produced (SP) maximum associated with the dilution by 14–29% when the dilution rate was 22% h⁻¹ and by 53–73% when the rate was 55% h⁻¹. The CB-III mechanism underpredicted the maximum by 17% at the lower dilution rate (when the cumulative light flux was moderate), but agreed with the observations at the higher dilution rate (when the cumulative light flux was high). Five emissions experiments were conducted at moderate to very high HC/NO_x ratios (8.3–51.0). When HC were injected during the light-limited regime the rate of formation of SP increased markedly; when NO was injected in this regime there was less effect (a slight decrease in slope). When HC were injected during the NO_x-limited regime there was a gradual decline in SP concentration, but when NO was injected during the NO_x-limited regime there was a dramatic increase in SP, leading to a second light-limited regime and a second NO_x-limited regime. When both HC and NO_x were injected during the light-limited regime, marked increases in slope occured after each injection. The Caltech model gave good to excellent agreement with the data. In one experiment it overestimated the final SP by 8%. The CB-III model performed next best, sometimes in excellent agreement with the data, but at other times underpredicting the final SP by 14–18%. The CB-XR and CB-IV models underpredicted the final SP for most of the experiments by up to 38%.     

富氧条件下等离子体协同改性NaY分子筛催化分解NO_x研究

用不同浓度的Cu、Ce和La离子交换Na Y分子筛,对比了不同改性条件下等离子体协同分解NO_x的性能.实验结果表明:Cu是NO_x催化分解的主要活性组分,对于8%Cu-Na Y催化剂,当放电电压为10 k V,放电功率为7.6 W时,NO_x转化率可达46.3%,反应产物中没有NO_2,只有11 ppm的N_2O.Ce的加入可以有效提高催化剂催化活性,对于5%Ce-8%Cu-NaY催化剂,当放电电压为7.8 kV,功率为3.6 W时,NO_x转化率可达67.3%.La的加入同样可以使催化剂活性上升,但不同La含量催化剂的NO_x转化率相差较小.     

Catalyst for NOx removal in nitric-acid plant gaseous effluents

The behaviour of a V₂O₅WO₃TiO₂ phosphorated catalyst, in the Selective Catalytic Reduction (SCR) of equimolar NO + NO₂ mixtures, is studied in order to analyse the possibility of its industrial utilization for the treatment of nitric-acid plant stack gases. With this new catalyst, an NO_x conversion higher than 90% molar can be achieved, the ammonia concentration at the exit gas being lower than that required to form ammonium salts, throughout the temperature range of commercial interest: 250–450°C, at a relatively high space velocity (GHSV ⩽ 40000 h⁻¹ NC). The effect of several operating variables such as oxygen concentration and NO₂/NO molar ratio in the feed is also discussed.     

北京城区夏季O3化学生成过程

选取2007年7月1日—8月31日中的21个晴空日,利用观测资料和光化学箱模式计算了北京城区测点的O₃生成速率G(O₃)和O₃生成效率OPE.结果表明,21个晴空日中G(O₃)日最高小时值分布在(18~82)×10^-9h^-1之间;在O₃污染和非污染日G(O₃)最高值的平均水平无显著差异,且与O_x浓度之间不存在一致的对应关系,表明O₃化学生成过程不能全面解释地面O₃浓度的累积,物理传输过程对测点O₃实测浓度有显著作用;各个化学过程对G(O₃)的贡献率对比结果显示,HO₂ 在 NO向NO₂的转化中贡献最大;OPE值分布在2.8~5.8之间,总体水平为4.1±0.1;OPE值与NO_x浓度之间为非线性关系,OPE值随NO_x浓度的增加而减少,表明消减测点附近VOCs排放能有效降低O₃浓度.     

Toluene decomposition performance and NOx by-product formation during a DBD-catalyst process

Characteristics of toluene decomposition and formation of nitrogen oxide (NO_x) by-products were investigated in a dielectric barrier discharge (DBD) reactor with/without catalyst at room temperature and atmospheric pressure. Four kinds of metal oxides, i.e., manganese oxide (MnOx), iron oxide (FeOx), cobalt oxide (CoOx) and copper oxide (CuO), supported on Al₂O₃/nickel foam, were used as catalysts. It was found that introducing catalysts could improve toluene removal efficiency, promote decomposition of by-product ozone and enhance CO₂ selectivity. In addition,NO_xwas suppressedwith the decrease of specific energy density (SED) and the increase of humidity, gas flow rate and toluene concentration, or catalyst introduction. Among the four kinds of catalysts, the CuO catalyst showed the best performance in NO_x suppression. The MnOx catalyst exhibited the lowest concentration of O₃ and highest CO₂ selectivity but the highest concentration of NOx. A possible pathway for NOx production in DBD was discussed. The contributions of oxygen active species and hydroxyl radicals are dominant in NOx suppression.     

Reactive uptake of NO2 on volcanic particles: A possible source of HONO in the atmosphere

The heterogeneous degradation of nitrogen dioxide (NO₂) on five samples of natural Icelandic volcanic particles has been investigated. Laboratory experiments were carried out under simulated atmospheric conditions using a coated wall flow tube (CWFT). The CWFT reactor was coupled to a blue light nitrogen oxides analyzer (NO_x analyzer), and a long path absorption photometer (LOPAP) to monitor in real time the concentrations of NO₂, NO and HONO, respectively. Under dark and ambient relative humidity conditions, the steady state uptake coefficients of NO₂ varied significantly between the volcanic samples probably due to differences in magma composition and morphological variation related with the density of surface OH groups. The irradiation of the surface with simulated sunlight enhanced the uptake coefficients by a factor of three indicating that photo-induced processes on the surface of the dust occur. Furthermore, the product yields of NO and HONO were determined under both dark and simulated sunlight conditions. The relative humidity was found to influence the distribution of gaseous products, promoting the formation of gaseous HONO. A detailed reaction mechanism is proposed that supports our experimental observations. Regarding the atmospheric implications, our results suggest that the NO₂ degradation on volcanic particles and the corresponding formation of HONO is expected to be significant during volcanic dust storms or after a volcanic eruption.     

NOx和/或NH3气氛下SO2在高岭土表面非均相转化的实验研究

利用自制气溶胶反应器研究了NO_x和/或NH_3气氛下SO_2在高岭土表面的非均相转化过程,应用扫描电镜(SEM)对高岭土颗粒物形貌进行了表征.结果表明:高岭土颗粒表面的SO_2非均相转化致使其成分和形貌产生了较大变化.相同实验条件下,SO_2转化的协同作用程度由高到低依次为NH_3、NO_x/NH_3和NO_x气氛,相对湿度40%、有光照条件下,SO_2转化量增幅最高可分别达125%、75%和50%.所有气氛下,协同作用在无光照时在高相对湿度(40%~70%)区间更为突出,有光照时其显著性则体现在低相对湿度(20%~40%)区间.SO_2、NO_x、NH_3三者共存时,在高岭土颗粒表面发生的非均相反应过程既有协同作用又存在竞争反应.     

Experimental study of NO2 reduction in N2/Ar and O2/Ar mixtures by pulsed corona discharge

Non-thermal plasma technology has been regarded as a promising alternative technology for NOx removal. The understanding of NO2 reduction characteristics is extremely important since NO2 reduction could lower the total NO oxidation rate in the plasma atmosphere. In this study, NO2 reduction was experimentally investigated using a non-thermal plasma reactor driven by a pulsed power supply for different simulated gas compositions and operating parameters. The NO2 reduction was promoted by increasing the specific energy density （SED）, and the highest conversion rates were 33.7%, 42.1% and 25.7% for Ar, N2/Ar and O2/Ar, respectively. For a given SED, the NO2 conversion rate had the order N2/Ar 〉 Ar 〉 02/Ar. The highest energy yield of 3.31 g/kWh was obtained in N2/Ar plasma and decreased with increasing SED; the same trends were also found in the other two gas compositions. The conversion rate decreased with increasing initial NO2 concentration. Furthermore, the presence of N2 or O2 led to different reaction pathways for NO2 conversion due to the formation of different dominating reactive radicals.     

有氧条件下生物滤塔去除NOx的挂膜启动及研究

将优选后的好氧反硝化菌应用于生物过滤系统,用来脱除NOx模拟废气,研究了生物滤床在好氧条件下对NOx的处理效果和不同操作条件下的运行情况,并对NOx去除过程的作用机制进行了探讨.结果表明,生物滤塔经过26 d完成挂膜启动,该工艺系统能有效克服氧对反硝化菌活性的抑制作用,可实现对NOx的高效率脱除.NOx净化主要发生在滤...     

柴油/甲醇组合燃烧发动机的氮氧化物排放研究

在增压共轨发动机上采用柴油/甲醇组合燃烧(DMCC)方式进行了氮氧化物排放特性研究.对DMCC模式下NO x、NO、NO2等排放与纯柴油模式的对比分析表明:DMCC模式下的NO x排放比原机模式平均下降10%以上,NO平均下降幅度超过40%;采用DMCC模式后,NO2排放量都有明显大幅度的升高,并且NO2/NO比值呈现显著增大,平均高达100%以上.     

Photocatalytic removal of NO and NO2 using titania nanotubes synthesized by hydrothermal method

In this study, the photocatalysts of titania nanotubes(TNTs) were synthesized at different calcination temperatures using commercial Degussa TiO2(P25) as a precursor. The materials were then characterized by BET, SEM, TEM, and XRD analyses. The photocatalytic reactions with NO and NO2 under UV-A irradiation were both performed. The results showed that the photocatalytic reaction rate of NO was much faster than that of NO2, and the conversion of NO2 to nitrate was the rate-limiting step for photocatalytic removal of NOx if the nitrate produced cannot be removed continuously from the photocatalyst surface. For TNTs calcined at different temperatures, a significant enhancement was observed on the total NOx removal efficiency by TNT calcined at 500°C for both NO and NO2 photocatalytic reaction, which could be attributed to its high anatase crystallinity as well as high surface area. These two factors affect primarily on the NO2conversion step in which the high anatase crystallinity could be responsible for the high efficiency at the beginning, while the high surface area could be accounted for retaining this high efficiency from nitric acid poisoning during the test period.