Mineralization of dinitrotoluenes and trinitrotoluene of spent acid in toluene nitration process by Fenton oxidation

Fenton's reagent, UV/H2O2 and UV/Fenton's reagent were employed to mineralize dinitrotoluene (DNT) isomers and 2,4,6-trinitrotoluene (TNT) of spent acid in toluene nitration process. The bench-scale experiments were conducted to elucidate the influence of various operating variables on the performance of removal of total organic compounds (TOC) from spent acid, including reaction temperature, concentration of ferrous ion and H2O2 dosage. It is remarkable that organic compounds were completely mineralized by Fenton oxidation, of which removal efficiency is superior to that of UV/H2O2. Nevertheless, it makes slight difference between Fenton oxidation and UV/Fenton oxidation. According to the spectra identified by gas chromatograph/mass spectrometer (GC/MS), it is proposed that oxidative degradation of DNT isomers leads to o-, m-, p-mononitrotoluene (MNT) and 1,3-dinitrobenzene respectively. Besides, the oxidation of 2,4,6-TNT gives the 1,3,5-trinitrobenzene intermediate. Apparently, Fenton oxidation is promising for purification of spent acid industrially.     

芬顿试剂预处理杀螟丹农药废水

利用芬顿试剂(Fenton)氧化预处理杀螟丹农药废水,分别考察了H2O2与FeSO4·7H2O投加量、初始pH、反应时间、温度和摇床转速对Fenton试剂处理杀螟丹废水的影响。结果表明,杀螟丹废水初始COD为676.8 mg/L时,取废水样100 mL,优化反应条件为Fenton试剂的用量1 g FeSO4·7H2O+4 mL H2O2,初始pH值为3,搅拌强度为160 r/min 的摇床转速,反应温度25℃,反应时间60 min。在优化反应条件下COD的去除率达到83.9%。通过Fenton降解,废水可生化性BOD5/COD从0.0745~0.0747上升至0.9066~0.9228,可生化性大幅提高,为后续生化处理创造了条件。考虑到运用于工业废水处理中经济成本等实际问题,建议选取Fenton试剂的用量0.5 g FeSO4·7H2O+1 mL H2O2,COD去除效率能达到65.5%。     

Chemical oxidative degradation of methyl tert-butyl ether in aqueous solution by Fenton's reagent

Degradation of methyl tert-butyl ether (MTBE) in aqueous solution by Fenton's reagent (Fe2+ and H2O2) was investigated. Effects of reaction conditions on the oxidation efficiency of MTBE by Fenton's reagent were examined in batch experiments. Under optimum conditions, 15 mM H2O2, 2 mM Fe2+, pH 2.8 and room temperature, the initial 1 mM MTBE solution was reduced by 99% within 120 min. Results showed that MTBE was decomposed in a two-stage reaction. MTBE was first decomposed swiftly based on a Fe2+/H2O2 reaction and then decomposed somewhat less rapidly based on a Fe3+/H2O2 reaction. The detection of Fe2+ also supported the theory of the two-stage reaction for the oxidation of MTBE by Fenton's reagent. The dissolved oxygen in the solution decreased rapidly in the first stage reaction, but it showed a slow increase in the second stage with a zero-order kinetics. A reaction mechanism involving two different pathways for the decomposition of MTBE by Fenton's reagent was also proposed. Chemicals including tert-butyl formate, tert-butyl alcohol, methyl acetate and acetone were identified to be the primary intermediates and by-products of the degradation processes.     

Degradation of the herbicide 2,4-DP by anodic oxidation, electro-Fenton and photoelectro-Fenton using platinum and boron-doped diamond anodes

This paper reports the degradation of 2,4-DP (2-(2,4-dichlorophenoxy)-propionic acid) solutions of pH 3.0 by environmentally friendly electrochemical methods such as anodic oxidation, electro-Fenton and photoelectro-Fenton with a Pt or boron-doped diamond (BDD) anode. In the two latter techniques an O(2)-diffusion cathode was used and 1.0mM Fe(2+) was added to the solution to give hydroxyl radical (*OH) from Fenton's reaction between Fe(2+) and H(2)O(2) generated at the cathode. All treatments with BDD are viable to decontaminate acidic wastewaters containing 2,4-DP since they give complete mineralization, with loss of chloride ion, at high current due to the great production of oxidant *OH at the BDD surface favoring the destruction of final carboxylic acids. *OH formed from Fenton's reaction destroys more rapidly aromatic products, making the electro-Fenton and photoelectro-Fenton processes much more efficient than anodic oxidation. UVA light in photoelectro-Fenton with BDD has little effect on the degradation rate of pollutants. The comparative procedures with Pt lead to slower decontamination because of the lower oxidizing power of this anode. The effect of current on the degradation rate and efficiency of all methods is studied. The 2,4-DP decay always follows a pseudo-first-order kinetics. Chlorohydroquinone, chloro-p-benzoquinone and maleic, fumaric, malic, lactic, pyruvic, acetic, formic and oxalic acids are detected as products by chromatographic techniques. A general sequence accounting for by the reaction of all these intermediates with the different oxidizing agents is proposed.     

Contribution of free radicals to chlorophenols decomposition by several advanced oxidation processes

The chemical decomposition of aqueous solutions of various chlorophenols (4-chlorophenol (4-CP), 2,4-dichlorophenol (2-DCP), 2,4,6-trichlorophenol (2,4,6-TCP) and 2,3,4,6-tetrachlorophenol (2,3,4,6-TeCP)), which are environmental priority pollutants, is studied by means of single oxidants (hydrogen peroxide, UV radiation, Fenton's reagent and ozone at pH 2 and 9), and by the Advanced Oxidation Processes (AOPs) constituted by combinations of these oxidants (UV/H2O2 UV/Fenton's reagent and O3/UV). For all these reactions the degradation rates are evaluated by determining their first-order rate constants and the half-life times. Ozone is more reactive with higher substituted CPs while OH* radicals react faster with those chlorophenols having lower number of chlorine atoms. The improvement in the decomposition levels reached by the combined processes, due to the generation of the very reactive hydroxyl radicals. in relation to the single oxidants is clearly demonstrated and evaluated by kinetic modeling.     

Oxidation of diethylene glycol with ozone and modified Fenton processes

This paper describes a study of oxidation of diethylene glycol (DEG) by ozone and modified Fenton process (hydrogen peroxide and ferric salt mixture) in aqueous solution. Both oxidation processes were able to oxidize relatively high concentrations of DEG effectively. DEG reacted primarily through hydroxyl radical produced by decomposition of ozone, and about 3 mol of ozone were consumed per mole of DEG removed during the process. For modified Fenton oxidation, stepwise addition of hydrogen peroxide (H2O2) and ferric salt (Fe(III)) resulted in much higher removal of DEG than one-time pulse addition of the chemicals. The extent of DEG removal increased with increasing concentrations of both H2O2 and Fe(III). Oxidant consumption per mole of DEG oxidized was one order of magnitude higher for hydrogen peroxide than those observed for ozone. Overall, ozonation produced higher concentrations of aldehydes, and modified Fenton treatment produced higher concentrations of carboxylic acids for the same levels of DEG oxidation. The major products of ozonation were glycolaldehyde, glyoxal, formaldehyde, acetaldehyde, and acetic, formic, pyruvic, oxalic and glyoxalic acids. The major products of modified Fenton oxidation were formaldehyde, and formic and acetic acids.     

Citric acid-modified Fenton's reaction for the oxidation of chlorinated ethylenes in soil solution systems

Fenton's reagent, a solution of hydrogen peroxide and ferrous iron catalyst, is used for an in situ chemical oxidation of organic contaminants. Sulfuric acid is commonly used to create an acidic condition needed for catalytic oxidation. Fenton's reaction often involves pressure buildup and precipitation of reaction products, which can cause safety hazards and diminish efficiency. We selected citric acid, a food-grade substance, as an acidifying agent to evaluate its efficiencies for organic contaminant removal in Fenton's reaction, and examined the impacts of using citric acid on the unwanted reaction products. A series of batch and column experiments were performed with varying H2O2 concentrations to decompose selected chlorinated ethylenes. Either dissolved iron from soil or iron sulfate salt was added to provide the iron catalyst in the batch tests. Batch experiments revealed that both citric and sulfuric acid systems achieved over 90% contaminant removal rates, and the presence of iron catalyst was essential for effective decontamination. Batch tests with citric acid showed no signs of pressure accumulation and solid precipitations, however the results suggested that an excessive usage of H2O2 relative to iron catalysts (Fe2+/H2O2<1/330) would result in lowering the efficiency of contaminant removal by iron chelation in the citric acid system. Column tests confirmed that citric acid could provide suitable acidic conditions to achieve higher than 55% contaminant removal rates.     

Degradation of clofibric acid in acidic aqueous medium by electro-Fenton and photoelectro-Fenton

Acidic aqueous solutions of clofibric acid (2-(4-chlorophenoxy)-2-methylpropionic acid), the bioactive metabolite of various lipid-regulating drugs, have been degraded by indirect electrooxidation methods such as electro-Fenton and photoelectro-Fenton with Fe(2+) as catalyst using an undivided electrolytic cell with a Pt anode and an O(2)-diffusion cathode able to electrogenerate H(2)O(2). At pH 3.0 about 80% of mineralization is achieved with the electro-Fenton method due to the efficient production of oxidant hydroxyl radical from Fenton's reaction between Fe(2+) and H(2)O(2), but stable Fe(3+) complexes are formed. The photoelectro-Fenton method favors the photodecomposition of these species under UVA irradiation, reaching more than 96% of decontamination. The mineralization current efficiency increases with rising metabolite concentration up to saturation and with decreasing current density. The photoelectro-Fenton method is then viable for treating acidic wastewaters containing this pollutant. Comparative degradation by anodic oxidation (without Fe(2+)) yields poor decontamination. Chloride ion is released during all degradation processes. The decay kinetics of clofibric acid always follows a pseudo-first-order reaction, with a similar rate constant in electro-Fenton and photoelectro-Fenton that increases with rising current density, but decreases at greater metabolite concentration. 4-Chlorophenol, 4-chlorocatechol, 4-chlororesorcinol, hydroquinone, p-benzoquinone and 1,2,4-benzenetriol, along with carboxylic acids such as 2-hydroxyisobutyric, tartronic, maleic, fumaric, formic and oxalic, are detected as intermediates. The ultimate product is oxalic acid, which forms very stable Fe(3+)-oxalato complexes under electro-Fenton conditions. These complexes are efficiently photodecarboxylated in photoelectro-Fenton under the action of UVA light.     

Influence of oxalic acid formed on the degradation of phenol by Fenton reagent

The objective of this work is to examine the influence of oxalic acid formed on the degradation of phenol by Fenton reagent. Oxalic acid formed at initial stage within 30 min significantly suppresses the reduction of ferric ion, thus terminating degradation reaction. The yield of oxalic acid is dependent on the amount of ferrous ion dosed since the minimal amount of oxalic acid is formed after the degradation reaction terminates. Mineralization of phenol by Fenton reagent stagnates after 120 min under the conditions used in this study. The reason why the mineralization stagnated can be assumed to be following two mechanisms other than the depletion of H₂O₂. In the case where a small amount of ferrous ions is dosed, the reduction of ferric ions is minimal by oxalic acid formed. In the case where a large amount of ferrous ions is dosed, the amount of degradable organic compounds is insufficient owing to preferential conversion to oxalic acid. The mineralization can be enhanced by the intermittent dosing of ferrous ions, which facilitates the suppression of oxalic acid formation during the degradation by Fenton reagent.     

可用于去除高盐废水中有机污染物的混凝-Fenton氧化联合工艺

以某环氧树脂生产厂产生的高盐有机废水为对象,对比研究了Fenton、Fenton-混凝、混凝-Fenton等工艺去除废水中有机污染物的效能。考察了Fenton反应中Fe2+、H2O2投加比、初始pH、反应时间以及混凝反应中混凝剂种类、投加量等参数对处理效果的影响。结果表明：Fenton工艺的最佳条件为亚铁和过氧化氢投加比1：20,投加量分别为25 mmol·L-1和500 mmol·L-1,初始pH 3,反应时间120 min,TOC去除率为62.50%;混凝工艺选择FeSO4混凝剂,投加量为300 mg·L-1,TOC去除率为23.78%;废水经过Fenton-无混凝剂混凝、Fenton-混凝剂混凝、混凝-一级Fenton氧化和混凝-二级Fenton氧化工艺处理,TOC去除率分别为68.32%、71.51%、80.69%和89.27%。     

Practical applications of the fenton reaction to the removal of chlorinated aromatic pollutants

BACKGROUND: Chlorophenols (CPs) constitute a group of organic pollutants that are introduced into the environment as a result of several man-made activities, such as uncontrolled use of pesticides and herbicides, and as byproducts in the paper pulp bleaching. Promising removal technologies of chlorinated aromatics consist in the application of advanced oxidation processes (AOPs) that can provide an almost total degradation of a variety of contaminants. Among these, wide application find Fenton systems based on generation of reactive species having a high oxidizing power, such as hydroxyl radical HO*. Our objective was that of determining the overall degradation efficiency of the model compound 2,4-dichlorophenol (DCP) by thermal Fenton-type oxidation systems with a view toward defining in more details relevant process parameters, the effect of reaction temperature and of co-catalyst Cu2+. METHODS: Reaction conditions were similar to those generally adopted as optimal in many practical applications, i.e. pollutant/Fe2+ (as FeSO4) ratio ca. 20, Fe2+/Cu2+ (co-catalyst) 2:1, pH adjusted and controlled at pH 3, and H2O2 in excess (up to four-fold over the stoichiometric amount required for complete mineralization). RESULTS AND DISCUSSION: The results demonstrate that it is advantageous to carry out the reaction at a temperature markedly higher (70 degrees C) than ambient. The stepwise addition of H2O2 in aliquots yields an efficient transformation, while allowing a convenient control of the reaction exothermicity. Under these conditions, the essentially complete removal of the initial DCP is accomplished using just one equiv of H2O2 during 15 min; excess H2O2 (5 equivalents) yields extensive substrate mineralization. Also relevant, at 70 degrees C dechlorination of the initial DCP (and of derived reaction intermediates) is remarkably extensive (3-5% residual TOX), already with the addition of 1 equiv of H2O2. At the end of the reaction, IC and IC-MS analyses of the solution reveal that only low-molecular weight carboxylic acid (acetic, formic, oxalic, malonic, tartaric, etc.) contribute to the residual TOC. CONCLUSIONS: The whole of the results herein point to the advantage of performing the process at temperatures substantially higher than ambient (70 degrees C). Under the conditions adopted, almost complete degradation of the initial toxic compound can be achieved using hydrogen peroxide in fair excess (e.g., 3.5 equiv H2O2). RECOMMENDATIONS AND OUTLOOK: In applying practical Fenton-type degradation systems to heavily polluted wastes, either for the pre-treatment of waters with a high COD value prior to biodegradation or for complete mineralization of pollutants, the set up of appropriate reaction conditions appears to be a key factor. Also, it is desirable to keep the concentration of iron salts within the lower limits in order to minimize the production and disposal of iron oxide sludges.     

镍网负载纳米TiO2光催化反应器对酸性品红脱色效果实验研究

采用负载纳米TiO2的三维镍网装配了光催化反应器,就其对酸性品红溶液进行脱色效果进行了实验研究。考察了反应器的3种装配条件、品红初始浓度、pH值、H2O2投加量、紫外光剂量等因素对酸性品红脱色效果的影响。结果表明：UV灯＋镍网＋TiO2模式组合的反应器脱色效果最好;在相同的处理时间内酸性品红溶液的脱色率随起始浓度的增大而减小;将酸性品红溶液pH值调至5时脱色效果最明显,70 min的脱色率可高达94.8%。脱色效果还可以通过溶液中添加H2O2和控制紫外线剂量来调节。当溶液中H2O2投加量为0.5 g/L时,处理70 min后的脱色率可高达98.3%;到达反应界面紫外光剂量越多则能够获得越高的酸性品红脱色率。     

Photodegradation of humic acids in the presence of hydrogen peroxide

A batch photoreactor was used to evaluate the UV/H2O2 oxidation process for the removal of humic acids in water. A 450-W UV lamp with high-pressure mercury vapor was employed as the light source. The residues of humic acids and hydrogen peroxide were measured for assessment of process performance and understanding of process reaction behavior. The UV photolysis alone can play an important role in the degradation of humic acids. The presence of hydrogen peroxide was found to promote the degradation efficiency. However, excessive dosage of H2O2 does not further improve the degradation of humic acids. On the contrary, the lower the H2O2 dosage the higher the amount of humic acids which can be removed. Aeration with air does not favor the removal efficiency of humic acids as the oxidation lasts for a sufficiently long time. The presence of carbonate species deteriorates the humic acids' removal, whereas it results in a larger amount of H2O2 decomposition.     

强化UV/Fenton法降解水中苯酚的研究

研究了UV/Fenton法处理含苯酚废水时H2 O2 和FeSO4 加入量及苯酚初始浓度对酚去除效果的影响及C2 O2 -4 对UV/Fenton法的增强效果。 [H2 O2 ]=2 0mmol/L ,[FeSO4 ]=5mmol/L ,反应 2 0min ,苯酚初始浓度为 5 0mg/L时 ,酚去除率达 99%。UV/Fenton体系中引入C2 O2 -4 后可有效提高对紫外和可见光的利用率 ,进而提高了对高浓度苯酚废水去除效果     

Mechanism for the destruction of carbon tetrachloride and chloroform DNAPLs by modified Fenton's reagent

The destruction of a carbon tetrachloride DNAPL and a chloroform DNAPL was investigated in reactions containing 0.5 mL of DNAPL and a solution of modified Fenton's reagent (2M H2O2 and 5mM iron(III)-chelate). Carbon tetrachloride and chloroform masses were followed in the DNAPLs, the aqueous phases, and the off gasses. In addition, the rate of DNAPL destruction was compared to the rate of gas-purge dissolution. Carbon tetrachloride DNAPLs were rapidly destroyed by modified Fenton's reagent at 6.5 times the rate of gas purge dissolution, with 74% of the DNAPL destroyed within 24h. Use of reactions in which a single reactive oxygen species (hydroxyl radical, hydroperoxide anion, or superoxide radical anion) was generated showed that superoxide is the reactive species in modified Fenton's reagent responsible for carbon tetrachloride DNAPL destruction. Chloroform DNAPLs were also destroyed by modified Fenton's reagent, but at a rate slower than the rate of gas purge dissolution. Reactions generating a single reactive oxygen species demonstrated that chloroform destruction was the result of both superoxide and hydroxyl radical activity. Such a mechanism of chloroform DNAPL destruction is in agreement with the slow but relatively equal reactivity of chloroform with both superoxide and hydroxyl radical. The results of this research demonstrate that modified Fenton's reagent can rapidly and effectively destroy DNAPLs of contaminants characterized by minimal reactivity with hydroxyl radical, and should receive more consideration as a DNAPL cleanup technology.     

Modeling the reaction kinetics of Fenton's process on the removal of atrazine

The degradation of pesticide, atrazine (ATZ), 2-chloro-4-(ethylamino)-6-(isopropylamino)-s-triazine, by Fenton's reagent (FR) was investigated as a function of reagents' concentrations and ratios in a batch reactor. The degradation of ATZ was effectively achieved by hydroxyl radicals, which were generated in the FR process. The decay rates of ATZ and the oxidation capacities of FR were found to depend on the concentrations of hydrogen peroxide and ferrous ion. The removal kinetics of ATZ are initiated by a rapid decay and then followed by a much slower one. After an extended reaction time (5-10 min), the reactions ceased because the Fe(II) and H(2)O(2) were consumed and would be deactivated in the process. A mathematical model was successfully developed to describe the two-stage reaction kinetics by using two simple but critical parameters: the initial ATZ decay rate and the final oxidation capacity of Fenton's process. In general, higher [Fe(II)] or H(2)O(2) concentrations result in faster initial decay rate and higher oxidation capacity. However, the oxidation capacity is more sensitive to the initial [Fe(II)] due to the presence of side reactions as discussed in the paper.     

An investigation into reservoir NOM reduction by UV photolysis and advanced oxidation processes

A comparison of four treatment technologies for reduction of natural organic matter (NOM) in a reservoir water was made. The work presented here is a laboratory based evaluation of NOM treatment by UV-C photolysis, UV/H(2)O(2), Fenton's reagent (FR) and photo-Fenton's reagent (PFR). The work investigated ways of reducing the organic load on water treatment works (WTWs) with a view to treating 'in-reservoir' or 'in-pipe' before the water reaches the WTW. The efficiency of each process in terms of NOM removal was determined by measuring UV absorbance at 254 nm (UV(254)) and dissolved organic carbon (DOC). In terms of DOC reduction PFR was the most effective (88% removal after 1 min) however there were interferences when measuring UV(254) which was reduced to a lesser extent (31% after 1 min). In the literature, pH 3 is reported to be the optimal pH for oxidation with FR but here the reduction of UV(254) and DOC was found to be insensitive to pH in the range 3-7. The treatment that was identified as the most effective in terms of NOM reduction and cost effectiveness was PFR.     

Fenton's pre-treatment of mature landfill leachate

The aim of this study was to check the effectiveness of the Fenton's reagent (Fe2+ + H2O2 + H+) for the pre-treatment of a municipal landfill leachate with the objective of improving its overall biodegradability, evaluated in terms of BOD5/COD ratio, up to a value compatible with biological treatment. The leachate came from a municipal sanitary landfill located in southern Italy and the average values of its main parameters were: pH=8.2; COD=10,540 mgl(-1); BOD5=2,300 mgl(-1); TOC=3,900 mgl(-1); NH4-N=5210 mgl(-1); conductivity=45,350 microScm(-1); alkalinity=21,470 mgl(-1) CaCO3. The effect of initial pH value on the pre-treatment effectiveness was evaluated by titrating the amount of acidic by-products formed. The extent of leachate oxidation was monitored and controlled by both pH and redox potential measurements. The best operational conditions for achieving the desired goal (i.e., BOD5/COD> or =0.5) resulted: Fe2+=275 mgl(-1); H2O2=3,300 mgl(-1); initial pH=3; reaction time=2 h. At the end of the Fenton's pre-treatment, in order to permit a subsequent biological treatment, residual ferric ions were removed increasing the pH up to 8.5 by adding 3 gl(-1) of Ca(OH)2 and 3 mgl(-1) of a cationic polyelectrolyte, the latter as an aid to coagulation. This final step also resulted in a further modest removal of residual COD due to co-precipitation phenomena.     

Temperature activated degradation (mineralization) of 4-chloro-3-methyl phenol by Fenton's reagent

With the aim to evaluate the effect of temperature, 4-chloro-3-methyl phenol (CMP) degradation by Fenton's reagent was investigated at 25 and 70 degrees C under the following initial conditions: [CMP]0 = 10 mM, [Fe2+]0 = 0.5 mM; ([H2O2]0/[CMP]0) = 80, pH0 = 3. The results indicated that CMP degradation was strongly influenced by temperature. In fact, the maximum TOC removal, achieved after ca. 24h, was by far greater at 70 degrees C (85%) than at 25 degrees C (36%). The same happened for organic chlorine (TOX) conversion into inorganic chloride, i.e. 100%, after 3 h at 70 degrees C, and 87%, after 27 h at 25 degrees C. As the recorded trends of CMP removal and chloride formation were basically the same, hydroxy substitution (ipso-substitution) was hypothesised as one likely mechanism of CMP degradation. The higher level of mineralization recorded at 70 degrees C was ascribed to: (i) a greater *OH concentration; (ii) a consequently greater extent of CMP oxidation to organic acids; (iii) a higher decarboxylation rate of such acids. An interesting consequence of such extended organic acids decarboxylation was a pH increase up to 8 that, in turn, caused, in the treated mixture, the decomposition of excess H2O2 as well as the precipitation of iron ions. These two latter outcomes are technologically important considering that usually, before discharging Fenton treated wastewater, specific polishing steps are required just to remove iron ions, decompose excess hydrogen peroxide and neutralise the pH.     

Intermediate distributions and primary yields of phenolic products in nitrobenzene degradation by Fenton's reagent

Nitrobenzene thermal degradation was investigated using the Fenton reagent in different experimental conditions. Reaction products were analyzed by HPLC, GC-MS, LC-MS and IC. The products obtained at different nitrobenzene conversion degrees show that degradation mainly involves successive hydroxylation steps of the aromatic ring and its subsequent opening followed by oxidation of corresponding aliphatic compounds. Our results show as primary reaction products: 4-nitrophenol, 3-nitrophenol, 2-nitrophenol, phenol and 1,3-dinitrobenzene, indicating that both hydroxylation and nitration reactions are involved. The formation of phenolic products can be explained by postulating an initial step of HO() addition to nitrobenzene ring. The mechanisms of primary reaction pathways are discussed and a detailed kinetic analysis to obtain the true primary yields of phenolic products is proposed. The relative yields observed for nitrophenol isomers do not follow the expected orientation according to deactivating characteristics of the nitro group but significantly depend on Fe(+2), Fe(+3), H(2)O(2) and O(2) concentrations. The understanding of the effect of reaction conditions on the relative product distribution benefits the application of Fenton and Fenton-like systems to waste water treatment.