Pt/CeO2催化氧化甲苯反应机制研究

采用浸渍法制备了Pt/CeO_2和Pt/Al2O_3催化剂,并通过XRD、BET、ICP-OES、H2-TPR、XPS等手段表征其物理化学性质.结果发现,Pt/CeO_2和Pt/Al2O_3催化剂上Pt负载量约为0.6%,Al2O_3载体上Pt颗粒尺寸更小,Pt/CeO_2的可还原性更强.甲苯催化氧化活性评价结果表明,Pt/CeO_2催化剂表现出更好的催化活性,T50=170℃,T90=190℃.通过UV-Raman、甲苯TPD、GC/MS、In-situ FTIR等手段进一步研究发现,Pt/CeO_2活化甲苯及反应供氧的机制与Pt/Al2O_3存在区别,其活性更好是因为:(1)负载在CeO_2表面存在高电子密度的Pt原子,具有更强的活化甲苯能力,可以直接使苯基和甲基间的C—C链发生断裂;(2)Pt的负载促进了CeO_2氧空位形成,进一步提高了CeO_2的储氧性能,加速氧循环.除了Pt解离气相氧之外,CeO_2还可以提供活性氧物种参与催化氧化甲苯的反应,进一步提高甲苯催化氧化效率.     

纳米CeO2催化氧化甲苯的形貌效应研究

采用水热法合成CeO2纳米棒、纳米颗粒和纳米立方体,利用XRD、BET-N2、TEM/HRTEM、Raman、O2-TPD和H2-TPR等表征手段进行表征,并利用连续流固定床反应法研究各催化剂对甲苯的催化氧化性能.结果表明,CeO2纳米棒因具有高比表面积和细颗粒尺寸,且表面主要暴露高活性的{100}/{110}晶面,拥有更多的氧空位和高活性氧物种,因此,催化活性最高,CeO2纳米颗粒次之,立方体最低.原位红外甲苯催化氧化机理分析进一步表明,CeO2纳米颗粒和纳米立方体上生成的羧酸盐物质难以进一步深度氧化,而纳米棒能在贫氧和低温条件下诱导甲苯的完全氧化和产物脱附,使甲苯得以快速降解.     

Pt颗粒尺寸对Pt/CeO2催化氧化甲苯性能影响

使用乙二醇还原法制备了一系列不同尺寸的Pt-x纳米颗粒(x=1.41、1.57、1.79、1.95、2.12、2.32 nm),将其负载于棒状(rod)CeO_2载体上.考察了不同尺寸的Pt颗粒催化剂Pt-x/CeO_2-rod在甲苯催化氧化反应中的催化性能.结果显示,随着Pt颗粒尺寸的增加,催化剂活性先升高后降低.其中,Pt颗粒尺寸为1.79 nm时催化剂催化活性最好,T90=133℃.一般认为,Pt颗粒尺寸增加其分散度减小,导致催化活性降低.然而本实验结果表明,随Pt尺寸增加催化活性先升高后降低,并且基于催化剂表面Pt原子计算的TOFs(turnover frequencies)随Pt尺寸增加逐渐变大.紫外拉曼光谱(UV Raman)、XRD、XPS显示,随着Pt颗粒尺寸增加,催化剂Pt-x/Ce-rod表面氧空位的浓度逐渐增加.氧空位有效提高了催化剂晶格氧的流动,促进了氧气的吸附活化及传递过程.Pt/Ce催化剂催化氧化甲苯反应活性是Pt分散度以及CeO_2表面氧空位浓度双重作用的结果.     

氧化锰与氧化铈协同等离子体催化氧化甲醇的活性差异研究

在等离子体催化系统中,不同催化剂常表现出显著的性能差异.本文通过表面氧物种表征及臭氧氧化原位反应,探究了α-MnO₂与CeO₂两种常用催化剂在等离子体催化系统中催化氧化甲醇性能差异的本质原因.等离子体催化氧化甲醇的性能评价结果显示,在相同输入功率下CeO₂对甲醇的转化率和CO₂选择性均高于α-MnO₂.氧气程序升温脱附（O₂-TPD）和X射线光电子能谱（XPS）等表征手段及甲醇常温催化、O₃分解和O₃催化氧化实验结果表明,CeO₂比α-MnO₂拥有更多的表面活性氧,能吸附活化更多的甲醇分子;同时,CeO₂能更有效地利用臭氧分解产生的活性氧物种对甲醇进行深度氧化.进一步通过原位DRIFTS实验研究两种催化剂协同臭氧催化氧化甲醇反应中间产物的变化,结果表明,CeO₂催化剂氧化甲醇的表面副产物较少,而α-MnO₂表面则会累积大量的副产物碳酸盐,从而影响其催化性能.     

活性半焦表面负载CeO2纳米管的制备及其低温脱硝机理

基于Zn O纳米棒的自腐蚀机制,分别在活性半焦表面修饰负载了CeO_2纳米管、CeO_2纳米颗粒,并发现活性半焦表面CeO_2纳米管的低温脱硝性能明显优于CeO_2纳米颗粒。通过N2吸附、XRD、XPD、NH3-TPD、H2-TPR等一系列表征发现:与纳米颗粒相比,CeO_2纳米管由于其独特的结构形式,表面暴露较多Ce、O原子,具有较高Ce3+与化学吸附氧Oα比例,拥有更多的酸性位点和较强的酸性,有利于NH3、NO的表面吸附和氧化,从而表现出较好的低温脱硝性能。     

基于EPR技术的5种纳米金属氧化物光生活性物种的形成研究

纳米金属氧化物的光化学性质使其成为新的催化剂和杀菌剂,而活性氧化物种(Reactive Oxygen Species,ROS)作为其具有催化杀菌性能的主要原因受到广泛关注.本研究通过电子顺磁共振(EPR)自旋捕捉和自旋标记技术,研究了5种纳米金属氧化物(n Al_2O_3、n CuO、n Ti O_2、n Fe_2O_3和n ZnO)在不同光照条件下形成光生电子、羟基自由基(·OH)、超氧阴离子(O_2~-·)和单线态氧(~1O_2)的能力.结果表明,在光照过程中,n Al_2O_3、n CuO、n Ti O_2和n ZnO能够生成·OH和~1O_2,n Fe_2O_3只生成了~1O_2.其中,n Ti O_2生成的光生电子和·OH最多,n CuO仅次于n Ti O_2,n Al_2O_3和n ZnO能够生成·OH,但生成量很少.本实验结果可为预测和评价纳米金属氧化物的光催化性能及环境风险提供一定的理论支持.     

坡缕石负载Mn-Cu催化剂催化燃烧甲苯研究

作者采用浸渍法制备了一系列不同温度焙烧的Mn-Cu/Pal-T催化剂,用于甲苯催化燃烧反应。结合XRD、BET、SEM、H2-TPR、NH3-TPD、XPS多种测试手段来分析催化剂的表面结构和化学态。结果表明,焙烧温度对催化剂催化燃烧甲苯性能有重要影响,因为其会导致催化剂物化性质的变化。在400℃焙烧制得的催化剂拥有最佳的催化氧化甲苯活性,甲苯完全转化温度仅需335℃。Mn-Cu/Pal-400催化剂拥有相对大的比表面积,CuO和Mn₂O₃活性物种在其表面高度分散。同时,拥有最佳的氧化还原性、最高比例的路易斯酸、最多的氧空穴和活性氧物种,这些均有利于甲苯深度氧化。相比之下,700℃下焙烧的催化剂Mn-Cu/Pal-700呈现最小的比表面积和路易斯酸比例、最少的活性氧物种和最差的氧迁移性,这无疑会导致最差的甲苯氧化性能。     

用于碳烟燃烧的Cu0.05Ce0.95O催化剂活性氧物种的研究 ——等离子体的强化效应

研究等离子体对柠檬酸络合法制备的Cu0.05Ce0.95-CA催化剂表面结构和物种的强化效应. TPO、H2-TPR、O2-TPD、XRD、BET和XPS等测试结果表明,催化剂处于等离子放电区时,其氧化碳烟燃烧的活性显著增强.在介质阻挡放电电压为9kV时,起燃温度为243.1℃,比无等离子的情况降低了65.1℃;燃烧峰值温度为302.8℃,降低92.7℃.在等离子体存在下,Cu0.05Ce0.95-CA催化剂有着更大的比表面积和更小的晶粒粒径;等离子体可以提高催化剂表面游离态的CuO的分散度,并使得更多的Cu2+进入CeO2晶格,形成更多的Cuy2+Ce1-y4+O2-y2-□y固熔体,催化剂储氧容量增大,在催化剂表面生成更多的活性氧物种,其流动、迁移和转化促进催化剂产生更多的氧空穴,如此循环,持续促进碳烟催化燃烧.     

聚合物辅助成型法制备纳米Co3O4/CeO2催化剂及其对CO低温氧化性能研究

采用聚合物辅助成型法,以乙二胺四乙酸(EDTA)和聚乙烯亚胺(PEI)为配位体制备了Co_3O_4/CeO_2催化剂,对其进行了氮气吸附、XRD、XPS、SEM、TEM、H2-TPR和CO-TPR等表征,并考察了材料的CO低温催化性能.结果表明,采用聚合物辅助成型法能够合成出具有三维空间网络结构的纳米Co_3O_4/CeO_2催化剂,Ce的加入有利于获得具有更小尺寸的Co_3O_4颗粒,并提高Co3+的相对含量,从而有利于CO低温催化性能的提高;Ce/Co的摩尔比为1时,样品具有最佳的CO催化性能,在催化温度为30℃时,可使初始浓度为100 ppm的CO完全转化;同时,纯氧气加热吹扫有利于催化剂的稳定再生.本研究可为CO低温催化剂的制备提供重要参考.     

焙烧温度对Fe2O3/SAPO-34催化剂低温NH3选择性催化还原NO性能的影响

采用尿素沉淀法制备了一系列Fe_2O_3/SAPO-34催化剂,考察了催化剂焙烧温度(200、300、400、500℃)对低温NH_3选择性催化还原(NH_3-SCR)NO性能的影响,并利用X射线衍射(XRD)、N_2吸附-脱附、原子吸收光谱(AAS)、场发射扫描电镜(FE-SEM)、X射线光电子能谱(XPS)、H_2程序升温还原(H_2-TPR)、NH_3程序升温脱附(NH_3-TPD)等多种手段对催化剂的表面结构和物理化学性质进行表征分析.XRD和FE-SEM分析表明,在较低的焙烧温度(400℃)下,铁物种能够高度均匀地负载在SAPO-34表面上.NH_3-TPD和H_2-TPR分析表明,高分散状态的Fe_2O_3使催化剂暴露出更多的强酸位和活性位,有利于提高催化剂的NH_3吸附和活化能力及氧化还原性能,从而使催化剂呈现出更高的低温SCR活性.BET和XPS分析表明,在较低的焙烧温度下,Fe_2O_3/SAPO-34催化剂具有更大的比表面积和更高的化学吸附氧比例,促进NO氧化为中间产物NO_2,从而加快低温SCR反应的进行.活性测试结果表明,300℃焙烧的Fe_2O_3/SAPO-34催化剂具有最佳的低温活性和较强的抗硫抗水性能,在空速为40000 h~(-1)的条件下,且反应温度为190~240℃时,NO转化率达90%以上且N_2选择性接近100%.     

Effect of CeO2 and Al2O3 on the activity of Pd/Co_3O_4/cordierite catalyst in the three-way catalysis reactions (CO/NO/CnHm)

The present article studies the effect of CeO₂ and Al₂O₃ on the activity of Pd/Co₃O₄/cordierite catalyst in conversion of NO, CO, C_nH_m. The catalysts were characterized by temperature programmed reduction with hydrogen, X-ray diffraction, X-ray photoelectron spectroscopy and transmission electron microscopy. It is shown that the effect of CeO₂ on the properties of Pd/Co₃O₄/cordierite catalyst depends on preparation method. The catalyst obtained by co-deposition of cerium and cobalt oxides has higher activity in CO oxidation (CO + O₂ and CO + NO) and total hexane oxidation (C₆H₁₄ + O₂). Such phenomenon is probably caused by more than stoichiometric amount of formed oxygen vacancies, an increase in both mobility of surface oxygen and dispersity of components in the catalytic composition. It is demonstrated that CeO₂ addition promotes the SO₂ resistance of Pd/Co₃O₄/cordierite. The second support decreases the activity of Pd/Co₃O₄/cordierite catalyst in the reactions of CO and C₆H₁₄ with oxygen because of CoAl₂O₄ formation.     

Effect of Ce doping of TiO2 support on NH3-SCR activity over V2O5-WO3/CeO2-TiO2 catalyst

CeO2–TiO2composite supports with different Ce/Ti molar ratios were prepared by a homogeneous precipitation method, and V2O5–WO3/CeO2–TiO2catalysts for the selective catalytic reduction（SCR） of NOx with NH3 were prepared by an incipient-wetness impregnation method. These catalysts were characterized by means of BET, XRD, UV–Vis,Raman and XPS techniques. The results showed that the catalytic activity of V2O5–WO3/TiO2 was greatly enhanced by Ce doping（molar ratio of Ce/Ti = 1/10） in the TiO2 support.The catalysts that were predominantly anatase TiO2 showed better catalytic performance than the catalysts that were predominantly fluorite CeO2. The Ce additive could enhance the surface adsorbed oxygen and accelerate the SCR reaction. The effects of O2 concentration, ratio of NH3/NO, space velocity and SO2 on the catalytic activity were also investigated. The presence of oxygen played an important role in NO reduction. The optimal ratio of NH3/NO was 1/1 and the catalyst had good resistance to SO2 poisoning.     

N/Ce doped graphene supported Pt nanoparticles for the catalytic oxidation of formaldehyde at room temperature

Pt catalysts with nitrogen-doped graphene oxide (GO) as support and CeO₂ as promoter were prepared by impregnation method,and their catalytic oxidation of formaldehyde (HCHO) at room temperature was tested.The Pt-CeO₂/N-rGO (reduced GO) with a mass fraction of 0.7% Pt and 0.8%CeO₂ exhibited an excellent catalytic performance with the 100% conversion of HCHO at room temperature.Physicochemical characterization demonstrated that nitrogendoping greatly increased the...     

Preparation of FexCe1-xOy solid solution and its application in Pd-only three-way catalysts

FeO_x-CeO₂ mixed oxides with increasing Fe/(Ce+Fe) atomic ratio (1-20 mol%) were prepared by sol-gel method and characterized by X-ray powder diffraction (XRD), Brunauer-Emmett-Teller (BET) and Hydrogen temperature-programmed reduction (H₂-TPR) techniques. The dynamic oxygen storage capacity (DOSC) was investigated by mass spectrometry with CO/O₂ transient pulses. The powder XRD data following Rietveld refinement revealed that the solubility limit of iron oxides in the CeO₂ was 5 mol% based on Fe/(Ce+Fe). The lattice parameters experienced a decrease followed by an increase due to the influence of the maximum solubility limit of iron oxides in the CeO₂. TPR analysis revealed that Fe introduction into ceria strongly modified the textual and structural properties, which influenced the oxygen handling properties. DOSC results revealed that Ce-based materials containing Fe oxides with multiple valences contribute to the majority of DOSC. The kinetic analysis indicated that the calculated apparent kinetic parameters obey the compensation effect. The three-way catalytic performance for Pd-only catalysts based on the Fe doping support exhibited the redundant iron species separated out of the CeO₂ and interacted with the ceria and Pd species on the surface, which seriously influenced the catalytic properties, especially after hydrothermal aging treatment.     

Layered sphere-shaped TiO2 capped with gold nanoparticles on structural defects and their catalysis of formaldehyde oxidation

We describe here a one-step method for the synthesis of Au/TiO₂ nanosphere materials, which were formed by layered deposition of multiple anatase TiO₂ nanosheets. The Au nanoparticles were stabilized by structural defects in each TiO₂ nanosheet, including crystal steps and edges, thereby fixing the Au–TiO₂ perimeter interface. Reactant transfer occurred along the gaps between these TiO₂ nanosheet layers and in contact with catalytically active sites at the Au–TiO₂ interface. The doped Au induced the formation of oxygen vacancies in the Au–TiO₂ interface. Such vacancies are essential for generating active oxygen species (*O⁻) on the TiO₂ surface and Ti^3 + ions in bulk TiO₂. These ions can then form Ti^3 +–O⁻–Ti^4 + species, which are known to enhance the catalytic activity of formaldehyde (HCHO) oxidation. These studies on structural and oxygen vacancy defects in Au/TiO₂ samples provide a theoretical foundation for the catalytic mechanism of HCHO oxidation on oxide-supported Au materials.     

纳米Fe3O4/CeO2-H2O2非均相类Fenton体系对3,4-二氯三氟甲苯的降解

以浸渍法制备的新型纳米Fe3O4/Ce O2为催化剂,3,4-二氯三氟甲苯(3,4-DCBTE)为目标污染物,在Fe3O4/Ce O2-H2O2非均相类Fenton体系中对目标污染物的降解进行研究,考察催化剂的催化效果和温度、p H、H2O2投加量等因素对催化剂催化效果的影响.结果表明,以纳米Fe3O4/Ce O2作为催化剂的非均相类Fenton体系对3,4-二氯三氟甲苯的处理效果极佳;随着温度的升高,纳米Fe3O4/Ce O2的催化效果不断提高;在偏酸性环境中,p H越低催化效果越好,p H=2时反应去除效率可达96.67%;随着H2O2投加量的增加,3,4-二氯三氟甲苯的降解效率先提高后降低,投加量为15 mg·L-1时去除效果最好可达99.47%;随着催化剂投加量的增加,同样出现了处理效果先升高后降低的现象,投加量为0.5 g·L-1时催化效果最好可达99.64%.在以纳米Fe3O4/Ce O2为催化剂的非均相类Fenton体系中,3,4-二氯三氟甲苯的降解符合一级反应动力学,反应所需活化能较低只需30.26 k J·mol-1.     

Cu-Mn-Ce ternary mixed-oxide catalysts for catalytic combustion of toluene

Cu–Mn, Cu–Mn–Ce, and Cu–Ce mixed-oxide catalysts were prepared by a citric acid sol–gel method and then characterized by XRD, BET, H_2-TPR and XPS analyses. Their catalytic properties were investigated in the toluene combustion reaction. Results showed that the Cu–Mn–Ce ternary mixed-oxide catalyst with 1:2:4 mole ratios had the highest catalytic activity, and 99% toluene conversion was achieved at temperatures below 220°C. In the Cu–Mn–Ce catalyst, a portion of Cu and Mn species entered into the Ce O_2 fluorite lattice, which led to the formation of a ceria-based solid solution. Excess Cu and Mn oxides existed on the surface of the ceria-based solid solution. The coexistence of Cu–Mn mixed oxides and the ceria-based solid solution resulted in a better synergetic interaction than the Cu–Mn and Cu–Ce catalysts, which promoted catalyst reducibility, increased oxygen mobility, and enhanced the formation of abundant active oxygen species.     

Mo源改性石墨相氮化碳(g-C3N4)活化过一硫酸盐可见光降解罗丹明B的性能研究

分别以钼酸钠（MA）和乙酰丙酮钼（MC）作为钼（Mo）源,采用热聚合法合成不同类型Mo-C₃N₄材料（MACN和MCCN）,并通过XRD、SEM、XPS、UV-Vis DRS等表征技术探究不同Mo源的引入对g-C₃N₄晶体结构和光学性质的影响.结果表明,Mo的引入增大了g-C₃N₄的晶格间距,以MC为Mo源合成的MCCN催化剂具有更大的比表面积、更宽的可见光响应范围和更低的能带宽度.将所合成的催化剂应用于耦合过一硫酸盐（PMS）可见光催化降解罗丹明B （RhB）研究,发现在催化剂浓度为0.5 g·L^-1、PMS浓度为1 mmol·L^-1、罗丹明B浓度为10 mg·L^-1的条件下,MCCN-4/PMS/Vis催化体系在25 min内对RhB的降解率高达94.1%,分别是MCCN-4/Vis和单独PMS催化体系的5.6和19.2倍,并且RhB光催化降解过程符合一级动力学方程.为进一步探索MCCN/PMS/可见光（Vis）催化体系的最佳工艺条件,系统考察了Mo的掺杂量、催化剂投加量、PMS浓度、污染物浓度、pH值等实际因素对RhB降解效果的影响.同时,循环实验表明,MCCN-4复合催化剂具有良好的稳定性和可重复性,3次循环之后仍保持89.1%的RhB降解率.此外,捕获实验和电子自旋共振测试（ESR）结果表明,在MCCN/PMS/Vis催化体系下,光生空穴（h⁺）和超氧自由基（·O₂^-）作为主要活性物种参与了RhB的降解.     

δ-MnO2 decorated layered double oxides in-situ grown on nickel foam towards electrothermal catalysis of n-heptane

Energy-saving and efficient monolithic catalysts are hotspots of catalytic purification of industrial gaseous pollutants. Here, we have developed an electrothermal catalytic mode, in which the ignition temperature required for the reaction is provided by Joule heat generated when the current flows through the catalyst. In this paper, Mn/NiAl/NF, Mn/NiFe/NF and Mn/NF metal-based monolithic catalysts were prepared using nickel foam (NF) as the carrier for thermal and electrothermal catalysis of n-heptane. The results indicated that Mn-based monolithic catalysts exhibit high activity in thermal and electrothermal catalysis. Mn/NiFe/NF achieve conversion of n-heptane more than 99% in electrothermal catalysis under a direct-current (DC) power of 6 W, and energy-saving is 54% compared with thermal catalysis. In addition, the results indicated that the introduction of NiAl (or NiFe) greatly enhanced the catalytic activity of Mn/NF, which attributed to the higher specific surface area, Mn³⁺/Mn⁴⁺, Ni³⁺/Ni²⁺, adsorbed oxygen species (O_ads)/lattice oxygen species (O_latt), redox performance of the catalyst. Electrothermal catalytic activity was significantly higher than thermal catalytic activity before complete conversion, which may be related to electronic effects. Besides, Mn/NiFe/NF has good cyclic and long-term stability in electrothermal catalysis. This paper provided a theoretical basis for applying electrothermal catalysis in the field of VOCs elimination.