PM10 Levels in the Lower Fraser Valley,British Columbia,Canada: An Overview of Spatiotemporal Variations and Meteorological Controls

ABSTRACT

Three years of hourly averaged PM₁₀ (particulate matter less than 10 Lrm in diameter) tapered element oscillating microbalance (TEOM) data from 10 sites in the large coastal valley incorporating Greater Vancouver were used to investigate the spatiotemporal dimensions and air pollution meteorology of particulate pollution. During the period studied, the provincial “acceptable” objective daily concentration of 50 μg m^-3 was exceeded at 7 of the 10 sites. The highest annual, seasonal, and maximum hourly concentrations were recorded at Abbotsford in the central valley. Mean seasonal PM₁₀ concentrations were highest in the wintertime in the western Lower Fraser Valley (LFV) and in the summertime at the central and eastern valley locations. Within the network, interstation correlations of daily average concentrations exceed 0.8 at interstation distances less than 20 km and decrease thereafter. For daily maximum concentrations (hourly), interstation correlations decrease sharply with distance. Meteorological conditions responsible for elevated par-ticulate concentrations in the LFV are associated with (1) short periods (1- to 3-hr duration) of reduced dispersion during summer nights at sites close to primary sources, (2) summer anticyclonic conditions when photochemical pollutant concentrations build up across the entire valley, and (3) occasional wintertime “gap wind” events in the eastern valley.     

Fugitive dust emission source profiles and assessment of selected control strategies for particulate matter at gravel processing sites in Taiwan

Particles emitted from gravel processing sites are one contributor to worsening air quality in Taiwan. Major pollution sources at gravel processing sites include gravel and sand piles, unpaved roads, material crushers, and bare ground. This study analyzed fugitive dust emission characteristics at each pollution source using several types of particle samplers, including total suspended particulates (TSP), suspended particulate (PM10), fine suspended particulate (PM2.5), particulate sizer, and dust-fall collectors. Furthermore, silt content and moisture in the gravel were measured to develop particulate emission factors. The results showed that TSP (< 100 microm) concentrations at the boundary of gravel sites ranged from 280 to 1290 microg/m3, which clearly exceeds the Taiwan hourly air quality standard of 500 microg/m3. Moreover, PM10 concentrations, ranging from 135 to 550 microg/m3, were also above the daily air quality standard of 125 microg/m3 and approximately 1.2 and 1.5 times the PM2.5 concentrations, ranging from 105 to 470 microg/m3. The size distribution analysis reveals that mass mean diameter and geometric standard deviation ranged from 3.2 to 5.7 microm and from 2.82 to 5.51, respectively. In this study, spraying surfactant was the most effective control strategy to abate windblown dust from unpaved roads, having a control efficiency of approximately 93%, which is significantly higher than using paved road strategies with a control efficiency of approximately 45%. For paved roads, wet suppression provided the best dust control efficiencies ranging from 50 to 83%. Re-vegetation of disturbed ground had dust control efficiencies ranging from 48 to 64%.     

Source apportionment of ambient total suspended particulates and coarse particulate matter in urban areas of Jiaozuo, China

Approximately 750 total suspended particulates (TSPs) and coarse particulate matter (PM10) filter samples from six urban sites and a background site and >210 source samples were collected in Jiaozuo City during January 2002 to April 2003. They were analyzed for mass and abundances of 25 chemical components. Seven contributive sources were identified, and their contributions to ambient TSP/PM10 levels at the seven sites in three seasons (spring, summer, and winter days) and a "whole" year were estimated by a chemical mass balance (CMB) receptor model. The spatial TSP average was high in spring and winter days at a level of approximately 530 microg/m(3) and low in summer days at 456 microg/m(3); however, the spatial PMo0 average exhibited little variation at a level of approximately 325 microg/m(3), and PM10-to-TSP ratios ranged from 0.58 to 0.81, which suggested heavy particulate matter pollution existing in the urban areas. Apportionment results indicated that geological material was the largest contributor to ambient TSP/PM10 concentrations, followed by dust emissions from construction activities, coal combustion, secondary aerosols, vehicle movement, and other industrial sources. In addition, paved road dust and re-entrained dust were also apportioned to the seven source types and found soil, coal combustion, and construction dust to be the major contributors.     

A retrospective comparison of model-based forecasted PM2.5 concentrations with measurements

This study presents an assessment of the performance of the Community Multiscale Air Quality (CMAQ) photochemical model in forecasting daily PM2.5 (particulate matter < or = 2.5 microm in aerodynamic diameter) mass concentrations over most of the eastern United States for a 2-yr period from June 14, 2006 to June 13, 2008. Model predictions were compared with filter-based and continuous measurements of PM2.5 mass and species on a seasonal and regional basis. Results indicate an underprediction of PM2.5 mass in spring and summer, resulting from under-predictions in sulfate and total carbon concentrations. During winter, the model overpredicted mass concentrations, mostly at the urban sites in the northeastern United States because of overpredictions in unspeciated PM2.5 (suggesting possible overestimation of primary emissions) and sulfate. A comparison of observed and predicted diurnal profiles of PM2.5 mass at five sites in the domain showed significant discrepancies. Sulfate diurnal profiles agreed in shape across three sites in the southern portion of the domain but differed at two sites in the northern portion of the domain. Predicted organic carbon (OC) profiles were similar in shape to mass, suggesting that discrepancies in mass profiles probably resulted from the underprediction in OC. The diurnal profiles at a highly urbanized site in New York City suggested that the overpredictions at that site might be resulting from overpredictions during the morning and evening hours, displayed as sharp peaks in predicted profiles. An examination of the predicted planetary boundary layer (PBL) heights also showed possible issues in the modeling of PBL.     

Characterization of major chemical components of fine particulate matter in North Carolina

This paper presents measurements of daily sampling of fine particulate matter (PM2.5) and its major chemical components at three urban and one rural locations in North Carolina during 2002. At both urban and rural sites, the major insoluble component of PM2.5 is organic matter, and the major soluble components are sulfate (SO4(2-)), ammonium (NH4(+)), and nitrate (NO3(-)). NH4(+) is neutralized mainly by SO4(2-) rather than by NO3(-), except in winter when SO4(2-) concentration is relatively low, whereas NO3(-) concentration is high. The equivalent ratio of NH4(+) to the sum of SO4(2-) and NO3(-) is < 1, suggesting that SO4(2-) and NO3(-) are not completely neutralized by NH4(+). At both rural and urban sites, SO4(2-) concentration displays a maximum in summer and a minimum in winter, whereas NO3(-) displays an opposite seasonal trend. Mass ratio of NO3(-) to SO4(2-) is consistently < 1 at all sites, suggesting that stationary source emissions may play an important role in PM2.5 formation in those areas. Organic carbon and elemental carbon are well correlated at three urban sites although they are poorly correlated at the agriculture site. Other than the daily samples, hourly samples were measured at one urban site. PM2.5 mass concentrations display a peak in early morning, and a second peak in late afternoon. Back trajectory analysis shows that air masses with lower PM2.5 mass content mainly originate from the marine environment or from a continental environment but with a strong subsidence from the upper troposphere. Air masses with high PM2.5 mass concentrations are largely from continental sources. Our study of fine particulate matter and its chemical composition in North Carolina provides crucial information that may be used to determine the efficacy of the new National Ambient Air Quality Standard (NAAQS) for PM fine. Moreover, the gas-to-particle conversion processes provide improved prediction of long-range transport of pollutants and air quality.     

Atmospheric particulate matter and polycyclic aromatic hydrocarbons for PM10 and size-segregated samples in Bangkok

Air samples of particulate matter (PM) with an aerodynamic diameter less than 10 microm (PM10) were collected from six sites in Bangkok, Thailand, using high-volume air samplers. Daily samples were taken at intervals of 12 days from November 1999 to November 2000. Size-selected sampling using a multislit Andersen size-fractionated cascade impactor was undertaken at one site in central Bangkok to identify particulate size distribution. The annual average PM10 concentration at all six sites exceeded the Thailand National Ambient Air Quality Standard (NAAQS) of 50 microg/m3. The daily PM10 concentrations at heavy traffic roadside areas ranged between 30 and 160 microg/m3. The highest PM10 level occurred during the winter period (November-February), which is the dry season. From our results, which are based on a 1-yr survey, it can be observed that the particulate concentrations are associated with traffic volumes and seasonal factors (temperature and rainfall). The relative importance of size fractions in contributing to PM load is presented and discussed. Twenty polycyclic aromatic hydrocarbons (PAHs) associated with PM have been identified and quantified. The summed PAHs based on the 20 species had an average concentration of 60 ng/m3. Benzo(e)pyrene, indeno(123cd)pyrene, and benzo(ghi)perylene were the major compounds with average concentrations of 8, 10, and 13 ng/m3, respectively. Results indicate that more than 97% of PAHs were found in the small particulate size range of <0.95 microm.     

The Steubenville comprehensive air monitoring program (SCAMP): associations among fine particulate matter, co-pollutants, and meteorological conditions

We determined 24-hr average ambient concentrations of PM2.5 and its ionic and carbonaceous components in Steubenville, OH, between May 2000 and May 2002. We also determined daily average gaseous co-pollutant concentrations, meteorological conditions, and pollen and mold spore counts. Data were analyzed graphically and by linear regression and time series models. Multiple-day episodes of elevated fine particulate matter (PM2.5) concentrations often occurred during periods of locally high temperature (especially during summer), high pressure, or low wind speed (especially during winter) and generally ended with the passage of a frontal system. After removing autocorrelation, we observed statistically significant positive associations between concentrations of PM2.5 and concentrations of CO, NOx, and SO2. Associations with NOx and CO exhibited significant seasonal dependencies, with the strongest correlations during fall and winter. NOx, CO, SO2, O3, temperature, relative humidity, and wind speed were all significant predictors of PM2.5 concentration in a time-series model with external regressors, which successfully accounted for 79% of the variance in log-transformed daily PM2.5 concentrations. Coefficient estimates for NOx and temperature varied significantly by season. The results provide insight that may be useful in the development of future PM2.5 reduction strategies for Steubenville. Additionally, they demonstrate the need for PM epidemiology studies in Steubenville (and elsewhere) to carefully consider the potential confounding effects of gaseous co-pollutants, such as CO and NOx, and their seasonally dependent associations with PM2.5.     

One-year study of the elemental composition and source apportionment of PM10 aerosols in Florence, Italy

An extensive investigation was carried out for the characterisation of the air particulate composition in Florence. The aim was to determine the aerosol elemental concentrations, as well as to identify pollution sources. For our investigation, the external Particle-Induced X-Ray Emission-Particle-Induced gamma-Ray Emission beam facility of the Istituto Nazionale di Fisica Nucleare, Van de Graaff accelerator at the Physics Department of the Florence University was used. We report the results of the analysis of a long temporal series (approximately 1 yr) of PM10 particulate samples, collected on Millipore filters on a daily basis in three different sites (characterised by different urban settings). Daily concentrations of more than 20 elements were detected. The long sampling period (approximately 1 yr) allowed a comparison with the air quality recommended values and the identification of seasonal variations. Four main sources (traffic, oil-combustion, soil-dust, and wind transported sea-salt) were extracted with the help of Principal Component Analysis (PCA). An absolute PCA showed traffic to be the major source both in the high traffic site and in the urban background site.     

Analysis of temporal and spatial dichotomous PM air samples in the El Paso-Cd. Juarez air quality basin.

This paper presents and discusses the results obtained from the gravimetric and chemical analyses of the 24-hr average dichotomous samples collected from five sites in the El Paso-Cd. Juarez air quality basin between August 1999 and March 2000. Gravimetric analysis was performed to determine the temporal and spatial variations of PM2.5 (particulate matter less than 2.5 microm in diameter) and PM25-10 (particulate matter less than 10 pm but greater than 2.5 microm in diameter) mass concentrations. The results indicate that approximately 25% of the PM10 (i.e., PM25 + PM25-10) concentration is composed of PM2.5. Concurrent measurements of hourly PM concentrations and wind speed showed strong diurnal patterns of the regional PM pollution. Results of X-ray fluorescence (XRF) elemental analyses were compared to similar but limited studies performed by the Texas Natural Resource Conservation Commission (TNRCC) in 1990 and 1997. Major elements from geologic sources-Al, Si, Ca, Na, K, Fe, and Ti-accounted for 35% of the total mass concentrations in the PM2.5-10 fraction, indicating that geologic sources in the area are the dominant PM sources. Levels of toxic trace elements, mainly considered as products of anthropogenic activities, have decreased significantly from those observed in 1990 and 1997.     

Chemical speciation of PM2.5 and PM10 in south Phoenix, AZ, USA

Phoenix, AZ, experiences high particulate matter (PM) episodes, especially in the wintertime. The spatial variation of the PM concentrations and resulting differences in exposure is of particular concern. In this study, PM2.s (PM with aerodynamic diameter <2.5 microm) and PM10 (PM with aerodynamic diameter <10 microm) samples were collected simultaneously from the east and west sides of South Phoenix and at a control site in Tempe and analyzed for trace elements and bulk elemental and organic carbon. Measurements showed that although PM2.5 concentrations had similar trends in temporal scale across all sites, concentrations of PM10 did not. The difference in PM10 concentrations and fluctuation across the three sites suggest effects of a local soil source as evidenced by high concentrations of Al, Ca, and Fe in PM10. K and anthropogenic elements (e.g., Cu, Pb, and Zn) in PM2.5 samples on January 1 were strikingly high, suggesting the influence of New Year's fireworks. Concentrations of toxic elements (e.g., Pb) in the study presented here are not different from similar studies in other U.S. cities. Application of principal component analysis indicated two broad categories of emission sources--soil and combustion--together accounting for 80 and 90% of variance, respectively, in PM2.5 and PM10. The soil and combustion components explained approximately 60 and 30% of the variance in PM10, respectively, whereas combustion sources dominated PM2.5 (>50% variance). Many elements associated with anthropogenic sources were highly enriched, with enrichment factors in PM2.5 an order of magnitude higher than in PM10 relative to surface soil composition in the study area.     

Measurement, analysis, and modeling of fine particulate matter in eastern North Carolina

An analysis of fine particulate data in eastern North Carolina was conducted to investigate the impact of the hog industry and its emissions of ammonia into the atmosphere. The fine particulate data are simulated using ISORROPIA, an equilibrium thermodynamic model that simulates the gas and aerosol equilibrium of inorganic atmospheric species. The observational data analyses show that the major constituents of fine particulate matter (PM2.5) are organic carbon, elemental carbon, sulfate, nitrate, and ammonium. The observed PM2.5 concentration is positively correlated with temperature but anticorrelated with wind speed. The correlation between PM2.5 and wind direction at some locations suggests an impact of ammonia emissions from hog facilities on PM2.5 formation. The modeled results are in good agreement with observations, with slightly better agreement at urban sites than at rural sites. The predicted total inorganic particulate matter (PM) concentrations are within 5% of the observed values under conditions with median initial total PM species concentrations, median relative humidity (RH), and median temperature. Ambient conditions with high PM precursor concentrations, low temperature, and high RH appear to favor the formation of secondary PM.     

Respirable particulate matter at an urban and nearby industrial location: concentrations and variability and synoptic weather conditions during high pollution episodes

Continuous data of the concentration measurements of respirable suspended particulates (PM10, particles with aerodynamic diameter smaller than or equal to 10 pm) were analyzed. These measurements were carried out at an urban and nearby industrial location in northern Greece for the 5-year period 1996-2000. The time series concentration trend was examined, the seasonal and diurnal variations were identified, and the lognormality of the daily mean concentration data sets was tested. Over the 5-year data-gathering period, the days on which the U.S. Environmental Protection Agency (EPA) 24-hr PM10 standard was exceeded (episode days) were identified and their relation to prevailing synoptic-scale meteorological conditions was studied. The analysis led to useful information concerning the air quality levels, the contribution of the main pollution sources in this area, as well as some of the mechanisms that influence the PM10 concentrations. It also was proved that the measured PM10 concentrations are a result of a combination of processes including local anthropogenic sources, mesoscale transport, and resuspension. A complex system of sources and meteorological conditions modulate the heavy particulate pollution in the area of interest.     

Spatial heterogeneity of PM10 and O3 in São Paulo, Brazil, and implications for human health studies

Developing exposure estimates is a challenging aspect of investigating the health effects of air pollution. Pollutant levels recorded at centrally located ambient air quality monitors in a community are commonly used as proxies for population exposures. However, if ample intraurban spatial variation in pollutants exists, city-wide averages of concentrations may introduce exposure misclassification. We assessed spatial heterogeneity of particulate matter with an aerodynamic diameter < or = 10 microm (PM10) and ozone (O3) and evaluated implications for epidemiological studies in S?o Paulo, Brazil, using daily (24-hr) and daytime (12-hr) averages and 1-hr daily maximums of pollutant levels recorded at the regulatory monitoring network. Monitor locations were also analyzed with respect to a socioeconomic status index developed by the municipal government. Hourly PM10 and O3 data for the Sāo Paulo Municipality and Metropolitan Region (1999-2006) were used to evaluate heterogeneity by comparing distance between monitors with pollutants' correlations and coefficients of divergence (CODs). Both pollutants showed high correlations across monitoring sites (median = 0.8 for daily averages). CODs across sites averaged 0.20. Distance was a good predictor of CODs for PM10 (p < 0.01) but not O3, whereas distance was a good predictor of correlations for O3 (p < 0.01) but not PM10. High COD values and low temporal correlation indicate a spatially heterogeneous distribution of PM10. Ozone levels were highly correlated (r > or = 0.75), but high CODs suggest that averaging over O3 levels may obscure important spatial variations. Of municipal districts in the highest of five socioeconomic groups, 40% have > or = 1 monitor, whereas districts in the lowest two groups, representing half the population, have no monitors. Results suggest that there is a potential for exposure misclassification based on the available monitoring network and that spatial heterogeneity depends on pollutant metric (e.g., daily average vs. daily 1-hr maximum). A denser monitoring network or alternative exposure methods may be needed for epidemiological research. Findings demonstrate the importance of considering spatial heterogeneity and differential exposure misclassification by subpopulation.     

Wood smoke contribution to winter aerosol in Fresno, CA

In an effort to better quantify wintertime particulate matter (PM) and the contribution of wood smoke to air pollution events in Fresno, CA, a field campaign was conducted in winter 2003-2004. Coarse and fine daily PM samples were collected at five locations in Fresno, including residential, urban, and industrial areas. Measurements of collected samples included gravimetric mass determination, organic and elemental carbon analysis, and trace organic compound analysis by gas chromatograph mass spectrometry (GC/MS). The wood smoke tracer levoglucosan was also measured in aqueous aerosol extracts using high-performance anion exchange chromatography coupled with pulsed amperometric detection. Sample preparation and analysis by this technique is much simpler and less expensive than derivatized levoglucosan analysis by GC/MS, permitting analysis of daily PM samples from all five of the measurement locations. Analyses revealed low spatial variability and similar temporal patterns of PM2.5 mass, organic carbon (OC), and levoglucosan. Daily mass concentrations appear to have been strongly influenced by meteorological conditions, including precipitation, wind, and fog events. Fine PM (PM2.5) concentrations are uncommonly low during the study period, reflecting frequent precipitation events. During the first portion of the study, levoglucosan had a strong relationship to the concentrations of PM2.5 and OC. In the later portion of the study, there was a significant reduction in levoglucosan relative to PM2.5 and OC. This may indicate a change in particle removal processes, perhaps because of fog events, which were more common in the latter period. Combined, the emissions from wood smoke, meat cooking, and motor vehicles appear to contribute approximately 65-80% to measured OC, with wood smoke, on average, accounting for approximately 41% of OC and approximately 18% of PM2.5 mass. Two residential sites exhibit somewhat higher contributions of wood smoke to OC than other locations.     

Estimation of ambient PM2.5 concentrations in Maryland and verification by measured values

In 1997, Maryland had no available ambient Federal Reference Method data on particulate matter less than 2.5 microm in aerodynamic diameter (PM23), but did have annual ambient data for PM smaller than 10 microm (PM10) at 24 sites. The PM10 data were analyzed in conjunction with local annual and seasonal zip-code-level emission inventories and with speciated PM2.5 data from four nearby monitors in the IMPROVE network (located in the national parks, wildlife refuges, and wilderness areas) in an effort to estimate annual average and seasonal high PM2.5 concentrations at the 24 PM10 monitor sites operating from 1992 to 1996. All seasonal high concentrations were estimated to be below the 24-hr PM2.5 National Ambient Air Quality Standards (NAAQS) at the sites operating in Maryland between 1992 and 1996. The estimates also indicated that 12 monitor sites might exceed the 3-year annual average PM2.5 NAAQS of 15 microg/m3, but Maryland's air quality shows signs that it has been improving since 1992. The estimates also were compared with actual measurements after the PM2.5 monitor network was installed. The estimates were adequate for describing the chemical composition of the PM2.5, forecasting compliance status with the 24-hr and annual standards, and determining the spatial variations in PM2.5 across central Maryland.     

First assessment of the PM<Subscript>10</Subscript> and PM<Subscript>2.5</Subscript> particulate level in the ambient air of belgrade city

INTENTION, GOAL, SCOPE, BACKGROUND: As the strong negative health effect of exposure to the inhalable particulate matter PM10 in the urban environment has been confirmed, the study of the mass concentrations, physico-chemical characteristics, sources, as well as spatial and temporal variation of atmospheric aerosol particles becomes very important. OBJECTIVE: This work is a pilot study to assess the concentration level of ambient suspended particulate matter, with an aerodynamic diameter of less than 10 microm, in the Belgrade central urban area. Average daily concentrations of PM10 and PM2.5 have been measured at three representative points in the city between June 2002 and December 2002. The influence of meteorological parameters on PM10 and PM2.5 concentrations was analyzed, and possible pollution sources were identified. METHODS: Suspended particles were collected on Pure Teflon filters by using a Mini-Vol low-volume air sampler (Airmetrics Co., Inc.; 5 l min(-1) flow rate). Particle mass was determined gravimetrically after 48 h of conditioning in a desiccator, in a Class 100 clean room at the temperature T = 20 degrees C and at about 50% constant relative humidity (RH). RESULTS AND DISCUSSION: Analysis of the PM10 data indicated a marked difference between season without heating--(summer; mean value 56 microg m(-3)) and heating season--(winter; mean value 96 microg m3); 62% of samples exceeded the level of 50 microg m(-3). The impact of meteorological factors on PM concentrations was not immediately apparent, but there was a significant negative correlation with the wind speed. CONCLUSIONS: The PM10 and PM2.5 mass concentrations in the Belgrade urban area had high average values (77 microg m(-3) and 61 microg m(-3)) in comparison with other European cities. The main sources of particulate matter were traffic emission, road dust resuspension, and individual heating emissions. When the air masses are coming from the SW direction, the contribution from the Obrenovac power plants is evident. During days of exceptionally severe pollution, in both summer and winter periods, high production of secondary aerosols occurred, as can be seen from an increase in PM2.5 in respect to PM10 mass concentration. RECOMMENDATION AND OUTLOOK: The results obtained gave us the first impression of the concentration level of particulate matter, with an aerodynamic diameter of less than 10 microm, in the Belgrade ambient air. Due to measured high PM mass concentrations, it is obvious that it would be very difficult to meet the EU standards (EEC 1999) by 2010. It is necessary to continue with PM10 and PM2.5 sampling; and after comprehensive analysis which includes the results of chemical and physical characterization of particles, we will be able to recommend effective control measures in order to improve air quality in Belgrade.     

Spatial and seasonal variation of PM10 mass concentrations in Taiwan

Hourly data of PM10 concentration collected from an air quality-monitoring network has been analyzed over Taiwan from 1994 to 1999. Fourteen sites from 72 monitoring stations were selected to evaluate the spatial and seasonal variations in the regions of north, southwest, south, east and National Park. The selected monitoring sites are located in a suburban environment, except Nantz and Linyuan that are located in industrial areas. Moreover, Yangming and Hengchuen are located in National Park. Spatial and seasonal variations of PM10 concentrations are rather large over Taiwan. Annual average in south is approximately six times higher than in National parks. In northern sites, the highest concentration occurs in March–May, which is attributed to the occurrence of dust storms in arid regions of central Asia and the transport of dust by northeasterly monsoon. A marked seasonal variation of PM10 concentrations can be observed both in southwestern and southern regions. The pattern is characterized by high concentrations in winter and low in summer. Appearance of the highest monthly PM10 concentration in winter of south may be in part due to the lowest number of monthly precipitation days and low temperature, both of which occurred in winter. The frequency of PM10 daily mean concentration for exceeded 150 μg m⁻³ is 15% during winter in south, which reflects the serious pollution problem there. Monitoring sites in National Park are representatives of remote environments, but the PM10 concentrations are still affected by the dust storms and human activities.     

Characterization of atmospheric particulates, particle-bound transition metals and polycyclic aromatic hydrocarbons of urban air in the centre of Athens (Greece)

The concentrations of trace metals and polycyclic aromatic hydrocarbons (PAHs) adsorbed to total suspended particulate (TSP) and finer fractions of airborne particulate matter (PM) were determined from a site in the centre of Athens (Greece), which is characterized by heavy local traffic and is densely populated, during the winter and summer periods in 2003-2004. Also, we collected and analyzed samples of diesel and gasoline exhaust particles from local vehicles (buses, taxis and private cars) and from chimney exhaust of residential central heating appliances. A seasonal effect was observed for the size distribution of aerosol mass, with a shift to larger fine fractions in winter. The most commonly detected trace metals in the TSP and PM fractions were Fe, Pb, Zn, Cu, Cr, V, Ni and Cd and their concentrations were similar to levels observed in heavily polluted urban areas from local traffic and other anthropogenic emissions. Analysis of 16 PAHs bound to PM showed that they are mostly traffic related. In general, the fine particulate PAHs concentrations were higher than coarse particles. The most common PAHs in PM(10.2) and PM(2.1) were pyrene, phenanthrene, acenapthylene and fluoranthene, which are associated with diesel and gasoline exhaust particles. The results of this study underlined the importance of local emission sources, especially vehicular traffic, central heating and other local anthropogenic emissions. Compared with other big cities, Athens has much higher levels of airborne particles, especially of the finer fractions PM(10) and PM(2.5), correlated with traffic-related air pollution.     

Transport and dispersion during wintertime particulate matter episodes in the San Joaquin Valley, California

Data analysis and modeling were performed to characterize the spatial and temporal variability of wintertime transport and dispersion processes and the impact of these processes on particulate matter (PM) concentrations in the California San Joaquin Valley (SJV). Radar wind profiler (RWP) and radio acoustic sounding system (RASS) data collected from 18 sites throughout Central California were used to estimate hourly mixing heights for a 3-month period and to create case studies of high-resolution diagnostic wind fields, which were used for trajectory and dispersion analyses. Data analyses show that PM episodes were characterized by an upper-level ridge of high pressure that generally produced light winds through the entire depth of the atmospheric boundary layer and low mixing heights compared with nonepisode days. Peak daytime mixing heights during episodes were -400 m above ground level (agl) compared with -800 m agl during nonepisodes. These episode/nonepisode differences were observed throughout the SJV. Dispersion modeling indicates that the range of influence of primary PM emitted in major population centers within the SJV ranged from -15 to 50 km. Trajectory analyses revealed that little intrabasin pollutant transport occurred among major population centers in the SJV; however, interbasin transport from the northern SJV and Sacramento regions into the San Francisco Bay Area (SFBA) was often observed. In addition, this analysis demonstrates the usefulness of integrating RWP/RASS measurements into data analyses and modeling to improve the understanding of meteorological processes that impact pollution, such as aloft transport and boundary layer evolution.     

Analysis of Temporal and Spatial Dichotomous PM Air Samples in the El Paso-Cd. Juarez Air Quality Basin

ABSTRACT

This paper presents and discusses the results obtained from the gravimetric and chemical analyses of the 24-hr average dichotomous samples collected from five sites in the El Paso-Cd. Juarez air quality basin between August 1999 and March 2000. Gravimetric analysis was performed to determine the temporal and spatial variations of PM_2.5 (particulate matter less than 2.5 um in diameter) and PM2.5-10 (particulate matter less than 10 μm but greater than 2.5 μm in diameter) mass concentrations. The results indicate that ~25% of the PM10 (i.e., PM2.5 + PM2.5-10) concentration is composed of PM2.5. Concurrent measurements of hourly PM concentrations and wind speed showed strong diurnal patterns of the regional PM pollution. Results of X-ray fluorescence (XRF) elemental analyses were compared to similar but limited studies performed by the Texas Natural Resource Conservation Commission (TNRCC) in 1990 and 1997. Major elements from geologic sources—Al, Si, Ca, Na, K, Fe, and Ti—accounted for 35% of the total mass concentrations in the PM2.5-10 fraction, indicating that geologic sources in the area are the dominant PM sources. Levels of toxic trace elements, mainly considered as products of anthropogenic activities, have decreased significantly from those observed in 1990 and 1997.