农药正辛醇／水分配系数的测定方法及其与其他环境参数的相关性

对已报道的农药正辛醇／水分配系数的６种测定方法进行了简述和比较，对农药Ｋｏｗ值与其他环境参数Ｓｗ，Ｋｏｃ，ＢＣＦ１的相关性进行了综述。     

Estimation of aqueous solubility of organic compounds by using the general solubility equation

The general solubility equation (GSE) proposed by Jain and Yalkowsky was used to estimate aqueous solubility of 1026 non-electrolytes. The only parameters used in the GSE are melting points (MP) and octanol-water partition coefficients (Kow). No fitted parameters and no training set are employed in the GSE. The experimental solubility values were taken from the AQUASOL dATAbASE. The average absolute error and the root-mean-square error in the solubility estimates are 0.38 and 0.53 log units, respectively. Thus, with an observed MP and calculated Kow; the users can obtain a reasonable estimation of the aqueous solubility of any organic non-electrolyte.     

Aqueous solubility, Henry's law constants and air/water partition coefficients of n-octane and two halogenated octanes

New data on the aqueous solubility of n-octane, 1-chlorooctane and 1-bromooctane are reported between 1 degree C and 45 degrees C. Henry's law constants, K(H), and air/water partition coefficients, K(AW), were calculated by associating the measured solubility values to vapor pressures taken from literature. The mole fraction aqueous solubility varies between (1.13-1.60)x10(-7) for n-octane with a minimum at approximately 23 degrees C, (3.99-5.07)x10(-7) for 1-chlorooctane increasing monotonically with temperature and (1.60-3.44)x10(-7) for 1-bromooctane with a minimum near 18 degrees C. The calculated air-water partition coefficients increase with temperature and are two orders of magnitude lower for the halogenated derivatives compared to octane. The precision of the results, taken as the average absolute deviations of the aqueous solubility, the Henry's law constants, or the air/water partition coefficients, from appropriate smoothing equations as a function of temperature is of 3% for n-octane and of 2% and 4% for 1-chlorooctane and 1-bromooctane, respectively. A new apparatus based on the dynamic saturation column method was used for the solubility measurements. Test measurements with n-octane indicated the capability of measuring solubilities between 10(-6) and 10(-10) in mole fraction, with an estimated accuracy better than +/-10%. A thorough thermodynamic analysis of converting measured data to air/water partition coefficients is presented.     

Determination of the temperature dependence of water solubilities of polycyclic aromatic hydrocarbons by a generator column-on-line solid-phase extraction-liquid chromatographic method

An improved dynamic coupled column liquid chromatographic (DCCLC) technique for determining water solubility data of hydrophobic compounds is presented. The technique is based on pumping water through a thermostated generator column in order to generate emulsion-free, saturated aqueous solutions of the compound under study. Through a switching valve system the solute in the aqueous solution is extracted and concentrated by an on-line solid-phase extraction process and subsequently eluted and analyzed by high performance liquid chromatography (fluorescence detection coupled to photodiode array detection). The improvements carried out to the original DCCLC technique have given rise to savings in time for the experimental work and increased sensitivity during the detection and quantification stage. Applicability of the method for studying highly hydrophobic substances is demonstrated by determining water solubility of anthracene and pyrene in the temperature range of 8.9-49.9 and 8.5-32.2 degrees C, respectively. The measured water solubilities are in good agreement with the best available literature data. The method has also been applied to the determination of water solubility of m-terphenyl, 9, 10-dihydrophenanthrene and guaiazulene, in the temperature range of 4.8-49.9, 4.8-25.0, and 4.5-29.9 degrees C, respectively. The uncertainty in the Sw values determined in this work ranged from 0.7% to 4.6%. The experimental water solubility data, as a function of temperature, are fitted to the equation In Sw = A + B/T; where Sw and T are given in mole fraction and Kelvin, respectively.     

Solubilization, solution equilibria, and biodegradation of PAH's under thermophilic conditions

Biodegradation rates of PAHs are typically low at mesophilic conditions and it is believed that the kinetics of degradation is controlled by PAH solubility and mass transfer rates. Solubility tests were performed on phenanthrene, fluorene and fluoranthene at 20 degrees C, 40 degrees C and 60 degrees C and, as expected, a significant increase in the equilibrium solubility concentration and of the rate of dissolution of these polycyclic aromatic hydrocarbons (PAHs) was observed with increasing temperature. A first-order model was used to describe the PAH dissolution kinetics and the thermodynamic property changes associated with the dissolution process (enthalpy, entropy and Gibb's free energy of solution) were evaluated. Further, other relevant thermodynamic properties for these PAHs, including the activity coefficients at infinite dilution, Henry's law constants and octanol-water partition coefficients, were calculated in the temperature range 20-60 degrees C. In parallel with the dissolution studies, three thermophilic Geobacilli were isolated from compost that grew on phenanthrene at 60 degrees C and degraded the PAH more rapidly than other reported mesophiles. Our results show that while solubilization rates of PAHs are significantly enhanced at elevated temperatures, the biodegradation of PAHs under thermophilic conditions is likely mass transfer limited due to enhanced degradation rates.     

Ecotoxicological Characterisation and Classification of Existing Chemicals

GOAL, SCOPE AND BACKGROUND: In 1998, the International Council of Chemical Associations (ICCA) launched a global initiative to investigate more than 1,000 HPV chemicals (High Production Volume, > or = 1,000 t/a) within the refocused OECD HPV Chemicals Programme. Up to the OECD SIDS Initial Assessment Meeting in April 2004 (SIAM 18) 147 ICCA dossiers (ca. 230 CAS-No) have been assessed based on a harmonised data set. The environmental profile and an ecotoxicological characterisation of these chemicals are presented here. Data for acute aquatic toxicity were correlated among each other, as well as data for fish (LC50, LD50) and rodents (LD50). The data for acute aquatic toxicity are compared with other existing chemicals. METHODS: Data of the ICCA HPV chemicals from the OECD SIAM 11-18 are presented for: log Kow (as an indicator for bioaccumulation potential), biodegradation, acute aquatic toxicity and availability of long-term toxicity data. Correlation analysis was performed with log transformed data and a linear regression model was fitted to the data, if a significant correlation was found. Acute toxicity for fish and acute oral toxicity for rodents were correlated on a molar basis. Acute aquatic toxicity of the chemicals is compared with data from BUA reports 1-234 and a random EINECS sample (Knacker et al. 1995). RESULTS AND DISCUSSION: According to the dossier information, 71 of the 147 ICCA chemicals are not 'readily biodegradable', 21 have a log Kow > or = 3, and 44 are 'toxic' (LC/EC50 < or = 10 mg/L) or 'very toxic' (LC/EC50 < or = 1 mg/L) to aquatic organisms. For 77, only the base set (acute fish, Daphnia and algae) is available, for the rest at least one long-term test (fish or Daphnia) is available and three tests for a mere 14 others. Based on the data presented, the SIAM gives recommendations for Environment and Human Health. 22 chemicals have been identified as a 'candidate for further work' for Environment and 16 for Human Health. The highest correlation coefficient was obtained correlating fish and Daphnia (r2 = 0.79). LC50 (fish) is significantly correlated with LD50 (rodent), but data are widely scattered. The correlation is not improved after transforming LC50 (fish) to LD50 (fish), using BCF QSAR. Based on acute aquatic toxicity, 25.1% of the chemicals from the BUA reports 1-234 are classified as 'very toxic' (LC/EC50 < or = 1 mg/L). This proportion is 2.5-fold higher than the ICCA HPV chemicals and 1.4-fold higher than the random EINECS sample. CONCLUSIONS: Correlation coefficients for aquatic toxicity data are rather uniform (0.57-0.79) compared with literature data, but also the best correlation was observed between fish and Daphnia. Because the scatter around the regression lines is still considerable, simple predictions of ecotoxicity between species are not possible. Correlation of LC50 (fish) and LD50 (rodent) indicates that toxicity is different. Surprisingly, the correlation of fish and rodent toxicity is not improved by transforming LC50 values to internal LD50s. The selection of ICCA chemicals by market significance (production volume) leads to a classification of toxicity, which is more comparable to a random sample of EINECS chemicals than to German BUA chemicals. The latter were chosen for concern (for Environment or Human Health). RECOMMENDATIONS AND OUTLOOK: Of 147 dossiers assessed between SIAM 11-18, ca. 75% were sponsored by the three following countries: Germany (42), USA (37) and Japan (33). The current output is about 50 dossiers per year (70-100 CAS-No), but a trend for an increase of output is noticeable. Industry, national authorities, and OECD work on a further development to speed up the output. The number of chemicals with 'low priority for further work' and the work recommended for the 'candidates' (mainly exposure assessment) indicate that the data presented were adequate for an initial hazard assessment according to OECD requirements. From the ICCA HPV list (n = 880, state of 1999) 44% of the chemicals have data available to cover all SIDS endpoints for Environment and only 33% for Human Health (Allanou et al. 1999). This indicates the importance of the Initiative to provide information on existing chemicals. The authors agree with the expectation "...that the scientific information provided by this global initiative will be considered as an internationally accepted and harmonised basis for further steps of chemicals management." (ICCA 2002 b).     

Transfer of pesticides to the brew during mate drinking process and their relationship with physicochemical properties

In order to evaluate the extraction of pesticide residues that are transferred to the brew during mate drinking process of P.U.1 yerba mate leaves (Ilex paraguariensis), a special device to simulate the way in which mate is drunk in Uruguay was developed. The transfer to the brew of 12 organophosphates, 5 synthethic pyrethroids and one organochlorine pesticide from spiked samples was studied. The relationship between the transfer data thus obtained and physicochemical properties like water solubility (Ws), octanol-water coefficient (Kow) and Henry's constant (H) was evaluated. The extractability of the pesticide residues from yerba mate can be correlated with log Ws and log Kow. These transfer values allowed the calculation of ARLs (acceptable residue level) for the pesticides following Food and Agriculture Organization (FAO), World Health Organizaion (WHO) guidelines. These results can help the future establishment of maximum residue levels (MRLs).     

Transfer of pesticides to the brew during mate drinking process and their relationship with physicochemical properties

In order to evaluate the extraction of pesticide residues that are transferred to the brew during mate drinking process of P.U.1 yerba mate leaves (Ilex paraguariensis), a special device to simulate the way in which mate is drunk in Uruguay was developed. The transfer to the brew of 12 organophosphates, 5 synthethic pyrethroids and one organochlorine pesticide from spiked samples was studied. The relationship between the transfer data thus obtained and physicochemical properties like water solubility (Ws), octanol-water coefficient (Kow) and Henry's constant (H) was evaluated. The extractability of the pesticide residues from yerba mate can be correlated with log Ws and log Kow. These transfer values allowed the calculation of ARLs (acceptable residue level) for the pesticides following Food and Agriculture Organization (FAO), World Health Organizaion (WHO) guidelines. These results can help the future establishment of maximum residue levels (MRLs)     

Partitioning of polychlorinated biphenyls in octanol/water, triolein/water, and membrane/water systems

The use of the octanol/water partition constant (Kow) as a surrogate parameter for lipid/water partitioning of persistent organic pollutants (POPs) was reassessed by comparing the measured Kow of 12 selected polychlorinated biphenyl congeners (PCBs) with partition constants in triolein/water (Ktw) and membrane/water (Kmw) systems. Kow and Ktw were measured by the slow-stirring method. Kmw was measured by an adaptation of the slow-stirring method using suspensions of phosphatidylcholine and phosphatidylserine liposomes. Partitioning of POPs to octanol, triolein, and liposomes is similar but not equal. The log-log correlation for Kow and Ktw is excellent (r2 = 0.982) and that for Kow and Kmw is somewhat weaker (r2 = 0.856). Ktw values are greater than Kow by a factor of 1.6. Kmw of some PCB congeners exceed both Kow and Ktw by an order of magnitude. The differences are attributed to different PCB activity coefficients in the different lipid phases. The results imply that Kow can be used as a reasonable conservative estimate of lipid/water partitioning. But the observed differences between Kow and Kmw also indicate that using Kow to predict accumulation of POPs, particularly highly hydrophobic ones, in the polar lipids of organisms will underestimate their concentrations at equilibrium.     

Mechanism-based quantitative structure-activity relationships for the inhibition of substituted phenols on germination rate of Cucumis sativus

Comparative inhibition activity (GC50) of 42 structurally diverse substituted phenols on seed germination rate of Cucumis sativus was investigated. Quantitative structure-activity relationships (QSARs) were developed by using hydrophobicity (1-octanol/water partition coefficient, logKow) and electrophilicity (the energy of the lowest unoccupied molecule orbital, Eluma) for the toxicity of phenols according to their modes of toxic action. Most phenols elicited their response via a polar narcotic mechanism and a highly significant log Kow-based model was obtained (GC50 = 0.92 log Kow + 1.99, r2 0.84, n = 29). The inclusion of E(lumo) greatly improved the predictive power of the polar narcotic QSAR (GC50 = 0.88 log Kow - 0.30E(lumo) + 1.99, r2 = 0.93, n = 29). pKa proved to be an insignificant influencing factor in this study. Poor correlation with hydrophobicity and strong correlation with electrophilicity were observed for the nine bio-reactive chemicals. Their elevated toxicity was considerably underestimated by the polar narcotic logKow-dependent QSAR. The nine chemicals consist of selected nitro-substituted phenols, hydroquinone, catechol and 2-aminophenol. Their excess toxic potency could be explained by their molecular structure involving in vivo reaction with bio-macromolecules. Strong dissociation of carboxyl group of the four benzoic acid derivatives greatly decreased their observed toxicity. In an effort to model all chemicals including polar narcotics and bio-reactive chemicals, a response-surface analysis with the toxicity, logKow and E(lumo) was performed. This resulted in a highly predictive two-parameter QSAR for most of the chemicals (GC50 = 0. 70 logKow - 0.66E(lumo) + 2.17, r2 = 0.89, n = 36). Catechol and 2,4-dinitrophenol proved to be outliers of this model and their much high toxicity was explained.     

Determination of the distribution coefficient (log Kd) of oxytetracycline,tylosin A,olaquindox and metronidazole in manure

Olaquindox (log Kow = -2.3) and metronidazole (log Kow = -0.1) both have low tendencies to sorp to particles in manure. This corresponds with the negative log Kow values of these antibiotics. Tylosin (log Kow = 1.63) and oxytetracycline (log Kow = -1.12) sorp relatively strongly to the manure particles and have log Kd values between 1.5 and 2.0. The tendency to bind to manure was ranked after increasing binding as follows: metronidazole < olaquindox < tylosin A and oxytetracycline. This order of ranking is consistent with results of sorption in soil. Our experiments illustrate that for some antibacterial agents estimation of the partitioning coefficients, Kd, cannot be made from Kow and f(oc) alone. Sorption of oxytetracycline to manure is much higher than expected from the negative log Kow value of the compound. It is believed that sorption of oxytetracycline to manure is influenced by ionic binding to divalent metal ions as such Mg2+ and Ca2+ as well as other charged compounds in the matrix. Binding of oxytetracycline to soil is stronger than the binding to manure. This is most likely due to the strong mineral related metal complexes formed between soil, metal ion and oxytetracycline. These complexes are not known to exist in manure. The relatively strong sorption of tylosin A to manure corresponds with data found for soil sorption of tylosin. Tylosin has a log Kow value of 2.5, thus it is not surprising that this drug binds strongly to manure.     

Determination of Henry's law constant for methyl tert-butyl ether (MTBE) at groundwater temperatures

The dimensionless Henry's law constant was determined for methyl tert-butyl ether (MTBE) at six temperatures (3, 5, 10, 15, 20 and 25 degrees C) by using a thermostatted flask (430 ml) containing an aqueous MTBE solution. The ratio between the gas phase and the water phase in the flask was approximately 1.7:1. The aim of this study was to acquire data needed to model the behaviour of MTBE at groundwater conditions. The dimensionless Henry's law constant at 10 degrees C is approximately 0.01 but is 0.03 at 25 degrees C. This is important for modelling MTBE because the variation of vaporization cannot be disregarded at groundwater temperatures. In a second experiment the water solubility of MTBE was determined to be 62.1 g/l at 5 degrees C and 35.5 g/l at 20 degrees C). The high solubility at low temperatures could cause MTBE plumes from spills (fuel accidents etc.) to spread rapidly.     

Quantitative structure-activity relationships for the inhibition toxicity to root elongation of Cucumis sativus of selected phenols and interspecies correlation with Tetrahymena pyriformis

The comparative toxicities of selected phenols to higher plants Cucumis sativus were measured and the negative logarithm molar concentration of the root elongation median inhibition (IRC50) were derived. Quantitative structure-activity relationships (QSARs) were developed to explore the toxicity influencing factors and for predictive purpose. The toxicity data, fell into two classes: polar narcosis and bio-reactive. For polar narcotic phenols, a highly significant two-parameter QSAR based on 1-octanol/water partition coefficient (logKow) and energy of the lowest unoccupied orbital (E(lumo)) was derived (IRC50 = 0.77 log Kow - 0.39E(lumo) + 2.36 n = 22 r2 = 0.89). The five bio-reactive chemicals proved to show elevated toxicity due to their typical substructure involved diverse reactive mechanisms. In an effort to model all chemicals, a robust multiple-variable QSAR combining logKow, E(lumo) and Qmax, the most negative net atomic charge, was developed (IRC50 = 0.65 logKow - 0.72E(lumo) + 0.23Qmax + 2.81 n = 27 r2 = 0.94), indicating that hydrophobicity, electrophilicity and hydrogen bond interaction contribute mainly to the phytotoxicity. The toxicological data was compared with Tetrahymena pyriformis 2-d population growth inhibition toxicity (IGC50) and excellent interspecies correlations were observed both for the polar narcotics and for five reactive chemicals (for polar narcotics: IRC50 = 0.95IGC50 + 1.07 n = 16 r2 = 0.89; for bio-reactive chemicals: IRC50 = 0.98IGC50 + 2.19 n = 5 r2 = 0.97; and for all: IRC50 = 0.93IGC50 + 1.63 n = 21 r2 = 0.87). This suggested that T pyriformis toxicity could serve as a surrogate of C. sativus toxicity for phenols and interspecies correlation also could be established for reactive chemicals.     

Study on the effect of temperature and pressure on nickel-electroplating characteristics in supercritical CO2

In this work, it was investigated the effect of solubility in supercritical CO2 on the nickel-electroplating characteristics. The plating characteristics could be controlled by electric resistance and dispersion in emulsion as well. CO2 concentration had better be controlled at lower concentration than 50 CO2 wt% to decrease electric resistance since supercritical CO2 is non-polar material. Non-ionic surfactant with EO/PO block copolymer was more efficient than any other surfactant and the dispersion at 0.2 surfactant wt% was better than at any surfactant concentration and over-added surfactant concentration over 0.2 wt% brought to the decrease of dispersion properties. Electric resistance was constant at 20Omega in ranging from pH 2.2 to pH 3.5 and increased slowly to 50Omega at pH 4 and rapidly to 400Omega at pH 5. Characteristics of nickel film has a close relation with solubility in supercritical CO2 and solubility is dependent on pressure and temperature. Solubility at 16 MPa was higher than that any other at pressure and at constant pressure of 16 MPa, solubility in supercritical CO2 increased with an increasing temperature from 31 to 45 degrees C and decreased over 45 degrees C.     

Study of fuel oxygenates solubility in aqueous media as a function of temperature and tert-butyl alcohol concentration

Methyl tert-butyl ether (MTBE) is the most widely used oxygenate in gasoline blending and has become one of the world’s most widespread groundwater and surface water pollutants. Alternative oxygenates to MTBE, namely ethyl tert-butyl ether (ETBE), tert-amyl ether (TAME) and diisopropyl ether (DIPE) have been hardly studied yet. The solubility of these chemicals is a key thermodynamic information for the assessment of the fate and transport of these pollutants. This work reports experimental data of water solubility at the range from 278.15 to 313.15 K and atmospheric pressure of ethers used in fuels (MTBE, ETBE, TAME and DIPE) due to the strong influence of temperature on its trend. From the experimental data, temperature dependent polynomials were fitted, thermodynamic parameters were calculated and theoretical models were used for prediction. Finally, the tert-butyl alcohol (TBA) influence in the solubility of MTBE and ETBE in aqueous media was studied.     

LogD: lipophilicity for ionisable compounds

The octanol/water partition coefficient (Kow) for organic compounds is widely used in predictive environmental studies. A significant proportion of contaminants of surface and ground water are ionisable (e.g. many pesticides, pharmaceuticals, metabolites). Such compounds may be partially ionised dependent on the pH. Since the neutral and ionic species exhibit different polarities, the Kow value of ionisable pesticides is pH dependent. It is therefore essential to determine Kow values over the full range of pH that occurs in the environment in order to get appropriate predictors. Numerous methods are available to measure lipophilicity but only a few are appropriate for ionisable pesticides (e.g. pH metric and filter probe methods). Parameters such as pH and ionic strength need to be carefully controlled when working with ionisable compounds. Variation of these factors probably explains why literature can yield Kow values that differ by more than one order of magnitude for some compounds. In this article, Kow values obtained for six acidic pesticides with three different methods are compared as well (data from the literature, measured by pH metric method and calculated with five computer programs). The values used in predictive regression equations needs to be either measured with a suitable method or selected from the literature with great care.     

Removal of polycyclic aromatic hydrocarbons from aged-contaminated soil using cyclodextrins: experimental study

The removal of polycyclic aromatic hydrocarbons (PAHs) from soil using water as flushing agent is relatively ineffective due to their low aqueous solubility. However, addition of cyclodextrin (CD) in washing solutions has been shown to increase the removal efficiency several times. Herein are investigated the effectiveness of cyclodextrin to remove PAH occurring in industrially aged-contaminated soil. Beta-cyclodextrin (BCD), hydroxypropyl-beta-cyclodextrin (HPCD) and methyl-beta-cyclodextrin (MCD) solutions were used for soil flushing in column test to evaluate some influent parameters that can significantly increase the removal efficiency. The process parameters chosen were CD concentration, ratio of washing solution volume to soil weight, and temperature of washing solution. These parameters were found to have a significant and almost linear effect on PAH removal from the contaminated soil, except the temperature where no significant enhancement in PAH extraction was observed for temperature range from 5 to 35 degrees C. The PAHs extraction enhancement factor compared to water was about 200.     

Sorptive behavior of sorgoleone in ultisol in two solvent systems and determination of its lipophilicity

Sorgoleone (SGL) exuded by sorghum roots inhibits the development of some weeds. Due to its high hydrophobicity, it is expected that SGL presents low soil mobility and limited allelopathic activity in the field. This work aims to evaluate the sorptivity of sorgoleone in octanol-water and in soil under two solvent systems. The two solvent systems were methanol:water (60:40) (MeOH:H2O) and pure methanol (MeOH). These two solvent systems promote different conditions for SGL solubility. Treatments were arranged in a 2 x 6 factorial (solvent systems x equilibrium concentrations in the solution (EC)). For each solvent, the sorption was achieved by shaking 500 mg of soil with 10 ml of 0, 5, 10, 15, 25, 40, and 60 mg L-1 of SGL solution, during 24 h. After centrifugation, the supernatant was filtered and the SGL concentration was determined by high performance liquid chromatography (HPLC). Data of sorbed amount of SGL were submitted to variance analysis, using a hierarchic factorial model. The data of sorbed amount (x/m) and equilibrium concentration (C) were fitted to the linear (x/m = a + KdC) and to the Freundlich (x/m = KfC1/n) models. The isotherm obtained for the MeOH:H2O system presented linear shape, whereas for the MeOH system a two subsequent linear isotherm was fitted. Sorgoleone is a highly hydrophobic compound, presenting a log Kow of 6.1. The sorption of sorgoleone to the soil was very high. The organic environment stimulated the sorgoleone sorption to the soil.     

Beta-cyclodextrin(beta-CD) influence on the biotoxicities of substituted benzene compounds and pesticide intermediates

The acute toxicities of 19 substituted benzene compounds and intermediates of pesticides to Photobacterium phosphoreum in beta-CD aqueous solution (5 g/L) were studied and compared with those in water through luminescent bacteria toxicity test, and 15min-EC50 values were obtained. The presence of beta-CD significantly reduce biotoxicities of the low-polarity compounds, while for the higher-polarity compounds, such effect was slight. The differences of biotoxicities were correlated with Log10Kow (octanol/water partition coefficients). A significant linear relationship was obtained with some abnormal data picked out. Some explanations concerning molecular structure of chemicals as well as beta-CD were given for the relationship.