Thermal research on the uncontrolled behavior of styrene bulk polymerization

Thermal runaway can occur during the styrene bulk polymerization process because of easily formed local hotspots resulting from the high viscosity of reactants and the difficulty of heat dissipation. To obtain the thermal hazard characteristics, the polymerization behavior of styrene was investigated using differential scanning calorimetry (DSC) at a scanning rate of β = 2 °C/min. Experimental results showed that the exothermic peaks obtained for heat initiation were different from those obtained when initiator was added. The exothermic peak changed from one to two after the initiator was added. The exothermic onset temperature (T₀) was also reduced. Phi-tech II was utilized to study the bulk polymerization of styrene in an adiabatic environment. The adiabatic temperature rise (ΔT_ad), starting temperature of uncontrolled polymerization (T_star), maximum temperature (T_end), and heat of polymerization (ΔH) under different conditions were acquired. When the dose of the additive was increased, the starting temperature of uncontrolled polymerization (T_star) decreased and the adiabatic temperature rise (ΔT_ad) increased gradually. Severity grading was performed based on the severity evaluation criteria of runaway reaction. The results can help designers decide whether it is necessary to take certain measures to reduce risk.     

Reaction hazard and mechanism study of H2O2 oxidation of 2-butanol to methyl ethyl ketone using DSC,Phi-TEC II and GC-MS

Methyl ethyl ketone (MEK) oxidation via H₂O₂ with tungsten-based polyoxometalate catalysts has gained much attention with an ever-growing body of knowledge focusing on the development of environmentally benign processes in chemical industry. In this study, two calorimetry techniques, differential scanning calorimetry (DSC) and Phi-TEC II adiabatic calorimetry, were employed to analyze the thermal hazards associated with the 2-butanol oxidation reaction system. Hydrogen peroxide was the oxidant and a tungsten-based polyoxometalate as the catalyst. Gas chromatography-mass spectrometry was used for identification of the organic products. Important thermal kinetic data were obtained including “onset” temperature, heat of reaction, adiabatic temperature rise and self-heat rate. From DSC results, three exothermic peaks were detected with a total heat generation of approximately 1.26 kJ/g sufficiently to induce a thermal runaway. Possible reaction pathway for three stages were proposed based on both DSC and GC-MS results. One exotherm was detected by Phi-TEC II calorimeter and the pressure versus temperature profile together with the DSC and GC-MS data demonstrate the complexity of 2-butanol reaction system under both thermal screening and adiabatic conditions.     

Research on thermal decomposition characteristics of H foaming agent with different moisture contents

N, N-Dinitroso pentamethylene tetramine, also known as H foaming agent, is a self-reactive chemical substance commonly used in the rubber industry. Decomposition, explosion and combustion may be caused by the presence of fire or high temperature. As a high-risk chemical that is strictly regulated in China, H foaming agent has ever triggered multiple accidents. During the study of the decomposition thermal process of H foaming agent, it was found that the presence of moisture content at different levels had a significant effect on its thermal stability. The thermal characteristics of H foaming agent under different moisture contents was studied through the test means such as adiabatic calorimetry and high-pressure differential scanning calorimetry. Through isothermal calorimetry experiment, it was found that the decomposition of H foaming agent had obvious auto-catalytic characteristics. In the moisture content within the range of 0–40%, with the increase of moisture content, the initial exothermic temperature T_onset of the mixture system of H foaming agent and water decreased, while the time from initial heat release to rapid temperature rise of the reaction system (induction period) was gradually prolonged, and the temperature increment of the reaction system was increased gradually. As the proportion of moisture content in the system increased, the adiabatic temperature rise ΔT_ad of the mixture system of H foaming agent and water gradually decreased, meanwhile the time to maximum rate under adiabatic condition (TMR_ad) gradually decreased. The research results have guiding significance for finding the reasonable moisture content of H foaming agent in the drying process and determining the upper temperature limit during storage and transportation.     

Experimental hazardous risk investigation of energetic styphnic acid analytical reagent in calorimetric analysis

Analytical reagents identify and manage metal pollution, a major environmental issue. Regrettably, these compounds' safety concerns, especially when heated, have been neglected. This research examines the thermal hazard of the extremely reactive analytical reagent styphnic acid. Differential scanning calorimetry, thermogravimetric analysis, and accelerating rate calorimetry examined styphnic acid's thermodynamics. Thermogravimetric analysis showed weight loss reactions starting at 127 °C and peaking at 208 °C. Differential scanning calorimetry showed an endothermic peak at 176 °C. The accelerating rate calorimetry test showed that styphnic acid self-accelerates at 237 °C after 196.5 °C. Kissinger, Ozawa-Flynn-Wall, and Kissinger-Akahira-Sunose thermokinetic models calculated apparent activation energy from 131.677 to 155.718 kJ/mol. A nonlinear regression analysis showed that styphnic acid undergoes a two-step autocatalytic reaction during heat degradation. Thermal safety was assessed by measuring time to conversion limit, maximum rate, total energy release, self-accelerating decomposition temperature, and adiabatic temperature rise. Styphnic acid is less stable at higher temperatures and its thermal hazards depend on heating rate. The computed SADT was 109.04 °C, with alarm and control temperatures of 104.04 and 99.04 °C, respectively. The risk matrix analysis based on T_ad and TMR_ad suggests reducing thermal instability. This study on styphnic acid's thermal risks and safe storage and transit during analytical applications is beneficial.     

Process hazard assessment of energetic ionic liquid with kinetic evaluation and thermal equilibrium

With the continuous development of battery technology, there are new research investments in materials of various parts. In the field of electrolytes, ionic liquids (IL) are considered to be excellent electrolytes and have been widely studied in distinct energy fields. However, it is necessary to pay attention to the safety characteristics of ionic liquids at high temperature due to the application of energy, but there is little research on the reaction and kinetics of ionic liquids. To ensure the safety of ionic liquids, such as high temperature, the common ionic liquid 1-Ethyl-3-methylimidazolium nitrate ([Emim] NO₃) was selected for analysis. The exothermic mode is obtained from the data of differential scanning calorimetry. The basic reaction parameters of [Emim] NO₃ were determined with thermodynamic equation simulation. For ionic liquids in the actual situation, consider adding a heat balance model to estimate its temperature change pattern and find out the hazard temperature and related safety parameters. Temperature changes were estimated by constructing 25.0 g and 50.0 g packages to simulate material reactions and heat transfer in the external environment. The results showed that [Emim] NO₃ had shorter TMR_ad and TCL (<1 day) when the temperature was above 180 °C.     

数值分析方法在一起高危工艺分析中的应用

以二级放热反应为研究对象,在反应体系温度、浓度均匀分布的假设基础上,根据反应速率方程和热平衡方程,建立高危工艺反应的温度和转化率随时间变化的数学模型。采用数值计算技术,以一阶差分代替微分,并结合工艺中的恒温过程、绝热过程和飞温过程,编写计算程序求得其转化率、温度在不同时间点的数值解,揭示爆炸事故的发展过程,定量分析操作参数的影响和转化率、温度随时间分布的规律。同时通过对绝热反应时间、冷凝器的冷却能力的分析,结合冷凝器的移热能力和反应放热对反应体系热积累的影响,讨论防止反应失控发生的可能性。最后探讨冷凝器热负荷余量、反应物投料浓度比等因素对控制反应失控的影响。     

Feasibility of honeycomb monolith supported sugar catalyst to produce biodiesel from palm fatty acid distillate (PFAD)

Carbon coated monolith was prepared by sucrose solution 65 wt.% via dip-coating method. Sulfonation of incomplete carbonized carbon coated monolith was carried out in order to synthesize solid acid catalyst. The textural structure characteristics of the solid acid catalyst demonstrated a low surface area and pore volume. Palm fatty acid distillate (PFAD), a by-product of palm oil refineries, was utilized as oil source in biodiesel production. The esterification reaction subjected to different reaction conditions was performed by using the sulfonated carbon coated monolith as heterogeneous catalyst. The sulfonation process had been performed by using vapour of concentrated H₂SO₄ that was much easier and efficient than liquid phase sulfonation. Total acidity value of carbon coated monolith was measured for unsulfonated sample (0.5 mmol/g) and sulfonated sample (4.2 mmol/g). The effect of methanol/oil ratio, catalyst amount and reaction time were examined. The maximum methyl ester content was 89% at the optimum condition, i.e. methanol/oil molar ratio (15:1), catalyst amount (2.5 wt.% with respect to PFAD), reaction time (240 min) and temperature 80 °C. The sugar catalyst supported on the honeycomb monolith showed comparable reactivity compared with the sugar catalyst powder. However, the catalyst reusability studies showed decrease in FFA% conversion from 95.3% to 68.8% after four cycles as well as the total acidity of catalyst dropped from the value 4.2 to 3.1 mmol/g during these cycles. This might be likely due to the leaching out of SO₃H group from the sulfonated carbon coated monolith surface. The leaching of active species reached a plateau state after fourth cycle.     

Case study on prevention of fire hazards in coating epoxy-based FRP work with illumination

In this study, we investigated and analyzed the causes of fire hazards on the basis of actual accidents that occurred during epoxy resin fiberglass-coating operations. Results of this study showed that during this process, two major factors could cause a fire. One factor was related to the heat produced during the mixing of the epoxy resin and a polyamide curing agent. From the results of thermal analysis, it was found that the T_onset of the epoxy resin and the polyamide curing agent was 52.8 °C by DSC and T_d10 was 58.9 °C by DT/TGA, causing an exothermic hazard. Further, the results of a pseudo-adiabatic analysis performed in a Dewar vessel showed that the temperature increased from 23.5 °C to 177 °C.The other factor that could increase fire hazard was the illumination source used during the coating operation. Depending on the type of illumination source used, the temperature could increase above 350 °C. The decomposition temperature (T_d10) of PVC was 276.3 °C. The experiments involving epoxy resin fiberglass coating using an illumination source showed serious burn marks, and the polyvinyl chloride (PVC) electrical cable emitted small flames. Therefore, it can be concluded that fire was caused by the combination of two factors—the exothermic reaction between epoxy resin and the polyamide curing agent and the effect of prolonged illumination, both of which caused an increase in temperature leading to auto-ignition of the PVC electric cable.     

Modeling thermal analysis for predicting thermal hazards relevant to transportation safety and runaway reaction for 2,2′-azobis(isobutyronitrile)

The pure decomposition behavior of 2,2′-azobis (isobutyronitrile) (AIBN) and its physical phase transformation were examined and discussed. The thermal decomposition of this self-reactive azo compound was explored using differential scanning calorimetry (DSC) to elucidate the stages in the progress of this chemical reaction. DSC was used to predict the kinetic and process safety parameters, such as self-accelerating decomposition temperature (SADT), time to maximum reaction rate under adiabatic conditions (TMR_ad), and apparent activation energy (E_a), under isothermal and adiabatic conditions with thermal analysis models. Moreover, vent sizing package 2 (VSP2) was applied to examine the runaway reaction combined with simulation and experiments for thermal hazard assessment of AIBN. A thorough understanding of this reaction process can identify AIBN as a hazardous and vulnerable chemical during upset situations. The sublimation and melting of AIBN near its apparent onset decomposition temperature contributed to the initial steps of the reaction and explained the exothermic attributes of the peaks observed in the calorimetric investigation.     

The critical runaway condition and stability criterion in the phenol–formaldehyde reaction

The procedure of phenol–formaldehyde polymerization is a rather important and complicated reaction in the chemical industry. This exothermic polymeric reaction releases a huge amount of heat. The high amount of energy accumulated and increasing temperature in this reaction process always lead to runaway reaction and a hazard situation owing to the high released heat and improper operation. In this investigation, we used sodium hydroxide as alkali–catalyst in the phenol–formaldehyde polymerization and estimated the reaction kinetics parameters to evaluate the thermal hazard conditions. The critical temperatures and stable criteria of the runaway reaction in this exothermic polymerization were evaluated. This technique is important and useful for safe operation in the phenol–formaldehyde polymerization process.     

Effects of environmental temperature on the thermal runaway of lithium-ion batteries during charging process

Lithium-ion batteries with relatively narrow operating temperature range have provoked concerns regarding the safety of LIBs. In this work, a series of experiments were conducted to explore the thermal runaway (TR) behaviors of charging batteries in a high/low temperature test chamber. The effects of charging rates (0.5 C, 1 C, 2 C, and 3 C), and ambient temperature (2 °C, 32 °C and 56 °C) are comprehensively investigated.The results indicate that the cell exhibited greater thermal hazard at the high charging rate and ambient temperature conditions. As the charging rate increased from 0.5 C to 3 C, more lithium intercalated in the anode prompt the TR triggered in advance, the TR onset temperature decreased from 297.5 °C to 264.7 °C. In addition, the charging time decreased with the elevated ambient temperature, resulting in a relatively higher TR onset temperature and lower maximum temperature, and the average TR critical time declined by 115–143 s. Finally, the TR required less heat accumulation with increasing of charging rate and ambient temperature, and the heat generation of side reaction played a substantial role that accounted for approximately 54%∼63%. These results provide an insight into the charging cell thermal runaway behaviors in complex operation environments and deliver valuable guidance for improving the safety of cell operation.     

Investigations on explosion characteristics of ethyl acetate

In this study, the confined explosion characteristics of ethyl acetate were investigated in a constant volume explosion vessel using the initial pressure of 1–4 bar, the initial temperature of 358–418 K, and the equivalence ratio of 0.8–1.4. It was revealed that the peak explosion pressure and the maximum pressure rise rate of ethyl acetate increased as the initial pressure increased and the initial temperature decreased. The peak explosion pressure and maximum pressure rise rate were obtained at the equivalence ratio of 1.2 due to increased heat release rate. Furthermore, the explosion time decreased as the initial pressure decreased. In summation, EA experimental and theoretical deflagration index were investigated and compared. The experimental deflagration index showed that EA explosion was less dangerous, whereas the theoretical deflagration predicted that the explosion could be more hazardous.     

Preparation of n-Octadecane@MF resin microPCMs and its application in temperature control of esterification reactions

Reaction thermal runaway accidents occur frequently and occupy a high proportion in chemical accidents. Reducing accidents by controlling reaction temperature is of great implication to enhance the safety level of chemical processes. Phase change materials (PCMs) have a good energy storage potential, which can rapidly convert the reaction exotherm in the reaction process into its own phase change latent heat, urgently control the reaction temperature, and enhance the process thermal safety level. In this study, using n-octadecane as the core and melamine-formaldehyde (MF) resin as the shell, microencapsulated phase change materials (microPCMs) was made, which has a smooth spherical shape, good thermal stability, and a phase change enthalpy up to 162.87 J/g. The homogeneous esterification reaction of 2-butanol (2 B) and propionic anhydride (PA) was selected as the target reaction, and then the reaction was scaled up equivalently to investigate the effect of amplification to the reaction system. The results indicated that the temperature control of the esterification reaction system by microPCMs is the synergy between physical inhibition and chemical inhibition. The reaction temperature could be controlled by adding microPCMs, and the temperature control effect improved with the increase of microPCMs addition. In large scale reactors, microPCMs still has certain temperature control ability after being added.     

Refinery wastewater degradation with titanium dioxide,zinc oxide,and hydrogen peroxide in a photocatalytic reactor

This paper presents the photo-catalytic degradation of real refinery wastewater from National Refinery Limited (NRL) in Karachi, Pakistan, using TiO₂, ZnO, and H₂O₂. The pretreatment of the refinery effluent was carried out on site and pretreated samples were tested at 32–37 °C in a stirrer bath reactor by using ultra-violet photo oxidation process. The degradation of wastewater was measured as a change in initial chemical oxygen demand (COD) and with time. Optimal conditions were obtained for catalyst type, and pH. The titanium dioxide proved to be very effective catalysts in photo-catalytic degradation of real refinery wastewater. The maximum degradation achieved was 40.68% by using TiO₂ at 37 °C and pH of 4, within 120 min of irradiations. When TiO₂ was combined with H₂O₂ the degradation decreased to 25.35%. A higher reaction rate was found for titanium dioxide. The results indicate that for real refinery wastewater, TiO₂ is comparatively more effective than ZnO and H₂O₂. The experiments indicated that first-order kinetics can successfully describe the photo-catalytic reaction. The ANOVA results for the model showed satisfactory and reasonable adjustment of the second-order regression model with the experimental data. The ANOVA results also showed that pH is significant than reaction time and catalyst dosage of TiO₂; and in case of ZnO, reaction time is significant than pH and catalyst dosage. This study proves that real refinery wastewater reacts differently than synthetic refinery wastewater, oil field produced water or oil water industrial effluent.     

Thermal risk analysis of cumene hydroperoxide in the presence of alkaline catalysts

Many studies have been performed to clarify the basic thermal runaway hazards and kinetics of cumene hydroperoxide (CHP) decomposition. However, materials that are incompatible with CHP have not been clearly identified. Alkaline solutions have been used as a catalyst to form dimethylphenyl carbinol (DMPC) and dicumyl peroxide (DCPO); however, these solutions also affect the reaction and storage temperature of CHP. In this study, thermal calorimeters, differential scanning calorimetry (DSC) and vent sizing package 2 (VSP2), were used to compare the effects of various bases on the decomposition of CHP in cumene. Specifically, the exothermic onset temperature, change in pressure over time, self-heating rate and heat of decomposition were evaluated. Moreover, to appraise the degree of hazard associated with the use of CHP, the compatibility of CHP with various substances was analyzed, and a risk matrix for thermal runaway reactions was obtained. The results of the present study could be used to design safety procedures for the production of CHP and its derivatives.     

Enhanced friction and shock sensitivities of hexachlorodisilane hydrolyzed deposit mixed with KOH

In this work, the effects of potassium hydroxide (KOH) on friction and shock sensitivity of the hexachlorodisialne hydrolysis products were studied. A wide range of KOH content, from 0.02 to 21.5 wt%, in the mixture of KOH and HCDS hydrolyzed deposit was prepared by mixing the deposit with aqueous KOH solution and dried in glovebox. The lowest impact energy (LIE) and lowest friction force (LFF) were determined by BAM fall-hammer and friction test apparatus, respectively. It was found that both shock and friction sensitivities increased with an increase in the KOH content in the HCDS hydrolyzed deposit. In particular, the LIE and LFF decrease from 6 J to 326 N of the original deposit to less than 0.125 J and 7 N for deposit with 0.03 and 0.3 wt% KOH. Differential scanning calorimetry studies showed that a new exothermic peak was observed between 80 °C and 150 °C which is also accompanied by evolution of hydrogen. It is proposed that, the presence of KOH results in the formation of Si–Si–OK groups leading to the weakening of the neighboring Si–Si bonds. Any mechanical impact or friction will lead to the cleavage of the unstable Si–Si bonds and subsequently initiate a fast chain oxidation of adjacent Si–Si and Si–OH bonds to form more Si–O–Si groups, releasing H₂ gas and heat. Recommendations were given for handling and disposing of these explosive deposits.     

Effect of flame propagation regime on pressure evolution of nano and micron PMMA dust explosions

Experiments using an open space dust explosion apparatus and a standard 20 L explosion apparatus on nano and micron polymethyl methacrylate dust explosions were conducted to reveal the differences in flame and pressure evolutions. Then the effect of combustion and flame propagation regimes on the explosion overpressure characteristics was discussed. The results showed that the flame propagation behavior, flame temperature distribution and ion current distribution all demonstrated the different flame structures for nano and micron dust explosions. The combustion and flame propagation of 100 nm and 30 μm PMMA dust clouds were mainly controlled by the heat transfer efficiency between the particles and external heat sources. Compared with the cluster diffusion dominant combustion of 30 μm dust flame, the premixed-gas dominant combustion of 100 nm dust flame determined a quicker pyrolysis and combustion reaction rate, a faster flame propagation velocity, a stronger combustion reaction intensity, a quicker heat release rate and a higher amount of released reaction heat, which resulted in an earlier pressure rise, a larger maximum overpressure and a higher explosion hazard class. The complex combustion and propagation regime of agglomerated particles strongly influenced the nano flame propagation and explosion pressure evolution characteristics, and limited the maximum overpressure.     

Investigation on the suppression effect of high momentum C6F12O (Novec-1230) flow on hydrogen jet flame

This work investigates the suppression effect of Novec-1230 on H₂ jet flame. The suppressants are motivated by N₂ flow to get higher momentum and approach the reaction kernel at flame base. The flame area with Novec-1230 is always smaller than that with water mist at the same condition. Novec-1230 exhibits better suppression effect on reaction kernel. The higher-momentum jet flame is more difficult to be suppressed. This is because that the higher-momentum flame makes the suppressant approach the reaction kernel more difficult. In addition, the high N₂ flow rate containing suppressant could destroy flame temperature structure and decrease it. Results inferred that the temperature of flame with Novec-1230 is higher than that with water mist. Moreover, the lower minimum extinguishing time indicates that the suppression efficiency of Novec-1230 is better than that of water mist. The jet flame is extinguished only when H₂ flow rate is low and N₂ flow rate is high. There are two reasons: one is that the higher-momentum jet flame prevents suppressants to enter flame core. The other one is that the burner nozzle is heated to as igniting source during suppression progress. Furthermore, the burning velocity, adiabatic flame temperature, heat production and free radicals are investigated theoretically at Φ = 1.6, 1.0, 0.8 and 0.6. Results indicate that the burning velocity with Novec-1230 is much lower than that with water mist. The adiabatic flame temperature, heat production and free radicals increase firstly and then decrease with Novec-1230 addition at lean flame.