Growing Carbon Nanotube on Aluminum Oxides: An Inherently Safe Approach for Environmental Applications

Using micron-sized Al₂O₃ particles as carriers to grow carbon nanotubes (CNTs) under 700°C atmosphere of methane and hydrogen after pre-planted catalysts of Fe–Ni nanoparticles, those composite CNTs (CCNTs) have demonstrated several unique properties compared to CNTs—medium specific surface area and zeta potential, high adsorption capacity for metal ions, high recovery rate by acids, low decomposition heat for exothermal reaction, and so on. The adsorption behaviours of Pb²⁺, Cu²⁺ and Cd²⁺ in aqueous solutions by CCNTs are in good agreement with the Langmuir adsorption isotherm and second order kinetic model with maximum individual adsorption capacities of 67.11, 26.59 and 8.89 mg g⁻¹. The individual and competitive adsorption behaviours indicated that the preference order of adsorption were Pb²⁺ > Cu²⁺ > Cd²⁺ for aluminum oxides, activated carbon, commercial CNTs, and CCNTs as well as other researchers’ CNTs. We suggest that future development of CNTs to combine with metals and/or other materials, such as TiO₂, should consider attached to carriers or surface in order to avoid concerns on environment, health and safety. Thus, growing CNTs on Al₂O₃ particles to form CCNTs is an inherently safe approach for many promising environmental applications.     

Disintegration of waste activated sludge by different applications of Fenton process

Oxidative disintegration of municipal waste activated sludge (WAS) using conventional Fenton (Fe²⁺ + H₂O₂, CFP) and Fenton type (Fe⁰ + H₂O₂, FTP) processes was investigated and compared in terms of the efficiency of sludge disintegration and enhancement of anaerobic biodegradability. The influences of different operational variables namely sludge pH, initial concentration of Fe²⁺ or Fe⁰, and H₂O₂ were studied in detail. The optimum conditions have been found as catalyst iron dosage = 4 g/kg TS, H₂O₂ dosage = 40 g/kg TS and pH = 3 within 1 h oxidation period for both CFP and FTP. Kinetics studies were performed under optimal conditions. It was determined that the sludge disintegration was happened in two stages by both processes: rapid and subsequent slow disintegration stages and rapid sludge disintegration stage can be described by a zero-order kinetic model. The effects of oxidative sludge disintegration under the optimum conditions on anaerobic digestion were experienced with biochemical methane potential (BMP) assay in batch anaerobic reactors. Total methane production in the CFP and FTP pre-treated reactors increased by 26.9% and 38.0%, relative to the untreated reactor (digested the raw WAS). Furthermore, the total chemical oxygen demand reductions in the pre-treated reactors were improved as well.     

Removal mechanism of trace oxytetracycline by aerobic sludge

To investigate the mechanism of removal of selected pharmaceuticals in activated sludge systems, laboratory-scale batch experiments were conducted to assess the adsorption and degradation behavior of trace oxytetracycline (OTC). The adsorption equilibrium of OTC was observed in 30 min and the adsorption process could be well described by a pseudo-second-order model with a rate of 0.362 L μg^?1 min^?1. The OTC adsorption rate decreased with increasing temperature and could be fitted by the Freundlich isotherm. The linear partition coefficients (K_d) were 1.19, 0.999, and 0.841 L g^?1 at temperatures of 15, 20, and 25 °C, respectively. Thermodynamic analysis revealed that the adsorption of OTC onto the inactivated sludge was spontaneous (ΔG = ?16.7 to ?17.0 kJ mol^?1), enthalpy-driven (ΔH = ?24.9 kJ mol^?1), entropy-retarded (ΔS = ?27.4 J (mol K)^?1), and predominantly a physical adsorption.     

Adsorption of copper and nickel on Na-bentonite

The removal of copper and nickel from aqueous solution on the Na-bentonite has been studied under static conditions. Experiments were carried out as a function of solution pH, dosage of Na-bentonite, contact time and temperature. The adsorption equilibrium for nickel and copper onto Na-bentonite is reached in 200 min. The adsorption of copper and nickel is pH dependent in the pH range 2–9. The kinetic process of adsorption can be described by the pseudo-second-order kinetic equation excellently and the adsorption isotherm be fitted to the Langmuir model by means of regression analyses very well. The adsorption capacities follow the order of Cu²⁺ > Ni²⁺ in single-component systems and competitive adsorption capacities in order decreasing is Cu²⁺ > Ni²⁺ in binary-component systems.     

On–off control of aeration time in the simultaneous removal of ammonia and manganese using a biological aerated filter system

The biological aerated filter (BAF) system, a new alternative in drinking water treatment, was designed to remove NH₄⁺–N and Mn²⁺ simultaneously. This study aimed to control the aeration time in the BAF system for simultaneous NH₄⁺–N and Mn²⁺ removal to achieve the Malaysian effluent quality regulation for drinking water. The experiment was conducted under four strategies of S1, S2, S3 and S4. The results demonstrated that acceptable levels of NH₄⁺–N and Mn²⁺ were achieved over a 6 h aeration period (S1), producing effluent concentrations of 0.7 mg/L (93.2% removal) and 0.08 mg/L (79.6% removal), respectively. At the initial treatment of S1 and S2, the dissolved oxygen (DO) level rapidly increased until it reached a saturated concentration (6.8 mg/L DO) after 2 h period. Automatic on–off aeration time to maintain 3 mg/L DO set point (S4) resulted with a good effluent quality of NH₄⁺–N and Mn²⁺ compared with the 2 mg/L DO set point (S3) which did not meet the regulated standard limits. Through the automatic on–off aeration time, the saturated and excessive DO levels in the BAF system can be avoided consequently reduce the wastage of energy and electrical consumption for simultaneous NH₄⁺–N and Mn²⁺ removal from drinking water treatment.     

Biosorption of zinc(II) on rapeseed waste: Equilibrium studies and thermogravimetric investigations

The removal of heavy metals from aqueous effluents so as to avoid their toxic, bioaccumulation and biomagnification effects to humans and environment is usually realized by means of physical, chemical treatment, and biological processes. The aim of this study is to evaluate the potential of rapeseed waste from biodiesel production as a biosorbent for Zn(II) ions.The ability of the rapeseed waste for Zn(II) biosorption exhibited a maximum at pH 4.5–5. The removal efficiency of Zn(II) from solution with an initial concentration of 72 mg L⁻¹ varied from 39% to 89% for an increase of the rapeseed waste dose from 2 to 30 g L⁻¹. The amount of Zn(II) retained on the tested rapeseed increased with increasing metal ion concentration, but the Zn(II) sorption percentage decreased. The equilibrium data are fitted to the Langmuir isotherm better than to the Freundlich isotherm. The kinetics of Zn(II) biosorption process follows a pseudo-second order model. The thermal stability of the rapeseed before and after Zn(II) biosorption was studied by thermogravimetric analysis. It was found that the zinc loaded rapeseed exhibits a better initial thermal stability than the original rapeseed, presumably due to the cross linking generated by the intermolecular complexation of Zn(II) ions. In both cases, the thermal decomposition takes place according to some reassembling kinetic models, in two phases with order n reactions. The results of this study strongly suggest the possibility to use rapeseed as an effective biosorbent for Zn(II) ions removal from aqueous effluents (municipal/industrial wastewaters).     

Comparative response of two organic biofilters treating ethylbenzene and toluene after prolonged exposure

The response of two biofilters filled with an organic waste material for treating ethylbenzene and toluene was studied for 415 and 472 operating days, respectively. The peak elimination capacities (EC_MAX) recorded were 170 g m^?3 h^?1 for ethylbenzene (EC_MAX) and 138 g m^?3 h^?1 for toluene. Regarding the degradation profile through the biofilters, an increase in the inlet concentration displaced the degradation profile into the downstream section. A sudden decrease in the performance of both biofilters occurred when the moisture content (MC) of the packing material exceeded 37% for ethylbenzene and 30% for toluene. Thus, a recommended MC value was established in the 15–30% range. Given the bioreactor was operated at a low MC level, fungi prevailed over bacteria. Nevertheless, synergism was detected between both microorganism types for the mineralization of the aromatic hydrocarbons.     

Pb(II) adsorption from aqueous solutions by raw and treated biomass of maize stover – A comparative study

The potential to remove Pb(II) ion from wastewater treatment systems using raw and treated maize stover through adsorption was investigated in batch experiments. To achieve this, batch mode experiments were conducted choosing specific parameters such as pH (2–8), dosage concentration (2–30 g L⁻¹), contact time (5–180 min), temperature (20–45 °C) and metal ion concentrations (10–50 mg L⁻¹). Adsorption was pH-dependent showing a maximum at pH value 5. The equilibrium sorption capacities of raw and treated maize stover were 19.65 and 27.10 mg g⁻¹, respectively. The adsorption data fitted well to the Langmuir isotherm model. Kinetic studies revealed that the adsorption process followed pseudo-second-order model. The calculated thermodynamic parameters showed that the adsorption of Pb(II) was spontaneous and exothermic in nature. Consequently, this study demonstrated that both raw and treated maize stover could be used as adsorbents for the treatment of Pb(II) from industrial wastewaters.     

Decolorization of synthetic Methyl Orange wastewater by electrocoagulation with periodic reversal of electrodes and optimization by RSM

Treatment of Methyl Orange (MO), an azo dye, synthetic wastewater by electrocoagulation with periodic reversal of the electrodes (PREC) was examined. Response Surface Methodology (RSM) was used to optimize the influence of experimental conditions for color removal (CR), energy consumption (ENC), electrode consumption (ELC) and sludge production (SP) per kg MO removed (kg(MO_r)) with optimal conditions being found to be pH 7.4, solution conductivity (к) 9.4 mS cm⁻¹, cell voltage (U) 4.4 V, current density (j) 185 mA cm⁻², electrocoagulation time (T) 14 min, cycle of periodic reversal of electrodes (t) 15 s, inter-electrode distance (d) 3.5 cm and initial MO concentration of 125 mg L⁻¹. Under these conditions, 97 ± 2% color was removed and ENC, ELC and SP were 44 ± 3 kWh kg(MO_r)⁻¹, 4.1 ± 0.2 kg(Al) kg(MO_r)⁻¹ and 17.2 ± 0.9 kg(sludge) kg(MO_r)⁻¹, respectively. With the enhanced electrochemical efficiency resulting from the periodic electrode reversal, the coefficients of increased resistance and decreased current density between the two electrodes in the PREC setup were 2.48 × 10⁻⁴ Ω cm⁻² min⁻¹ and 0.29 mA cm⁻² min⁻¹, respectively, as compared to 7.72 × 10⁻⁴ Ω cm⁻² min⁻¹ and 0.79 mA cm⁻² min⁻¹ as measured for the traditional electrocoagulation process. The rate constant of decolorization was also enhanced by 20.4% from 0.152 min⁻¹ in the traditional electrocoagulation process to 0.183 min⁻¹ in the PREC process. These performance characteristics indicate that the PREC approach may be more promising in terms of practical application, as a cost-effective treatment, than conventional electrocoagulation for textile dye removals.     

Artificial neural network modelling of As(III) removal from water by novel hybrid material

The present study reported a method for removal of As(III) from water solution by a novel hybrid material (Ce-HAHCl). The hybrid material was synthesized by sol–gel method and was characterized by XRD, FTIR, SEM–EDS and TGA–DTA. Batch adsorption experiments were conducted as a function of different variables like adsorbent dose, pH, contact time, agitation speed, initial concentration and temperature. The experimental studies revealed that maximum removal percentage is 98.85 at optimum condition: pH = 5.0, agitation speed = 180 rpm, temperature = 60 °C and contact time = 80 min using 9 g L⁻¹ of adsorbent dose for initial As(III) concentration of 10 mg L⁻¹. Using adsorbent dose of 10 g L⁻¹, the maximum removal percentage remains same with initial As(III) concentration of 25 mg L⁻¹ (or 50 mg L⁻¹). The maximum adsorption capacity of the material is found to be 182.6 mg g⁻¹. Subsequently, the experimental results are used for developing a valid model based on back propagation (BP) learning algorithm with artificial neural networking (BP-ANN) for prediction of removal efficiency. The adequacy of the model (BP-ANN) is checked by value of the absolute relative percentage error (0.293) and correlation coefficient (R² = 0.975). Comparison of experimental and predictive model results show that the model can predict the adsorption efficiency with acceptable accuracy.     

Continuous nitrifying granular sludge bioreactor: Influence of aeration and ammonium loading rate

Granulation of nitrifying bacteria was investigated in a continuous bubble column bioreactor. Then, the combined effect of aeration and ammonium loading rates on dissolved oxygen (DO) concentration as well as nitrification process was evaluated in the system using an experimental design technique. After 120 days, stable nitrifying granules with average diameter of 1.4 mm and settling velocities of 55 m/h were obtained. The influence of increasing ammonium loading rate (ALR) was found to be more significant than decreasing aeration rate on the reduction of DO concentration inside the nitrifying bioreactor. The system could handle the ALR values of 0.48–1.92 gNH₄⁺-N/L d with the ammonium removal efficiency from 65% to nearly 100% at the tested airflow rates of 2.5 and 4.5 L/min. At the low aeration, the complete ammonium conversion to nitrate was replaced with nitrite when the ALR increased to 1.44 gNH₄⁺-N/L d. At the high aeration, however, almost complete nitrification was achieved except the high ALR in which the nitrite accumulation was observed up to 38%. The study demonstrated that the continuous bioreactor had a considerable performance for obtaining stable nitrifying granules to have nitrite accumulation under control with changing the ratio of aeration rate and ALR.     

Acid-enhanced limestone defluoridation in column reactor using oxalic acid

Acid enhanced limestone defluoridation of water has been studied in a crushed limestone column reactor using oxalic acid (OA). The defluoridation has been studied with varying initial fluoride concentrations of 5, 10, 15 and 20 mg/L and acid concentrations of 0.01, 0.05 and 0.1 M. The fluoride removal was found to increase with increase in the concentration of the acid, removing fluoride up to 95% with 0.1 M OA. The observed good fluoride removal has been attributed to a combination of two mechanisms of fluoride removal, viz., precipitation of calcium fluoride and adsorption of fluoride ions on limestone surfaces. While the removal by precipitation remains same on repeated use of the same limestone column, the adsorption is more with the fresh limestone and decreases gradually on repeated use of the same limestone column. The precipitate has been characterized using various analytical tools, viz., X-ray diffraction, IR spectroscopy, thermogravimetric analysis, scanning electron microscopy combined with energy dispersive X-ray spectroscopy and X-ray photoelectron spectroscopy. The Ca²⁺ ions, formed due to dissolution of limestone by the acid, precipitate calcium fluoride along with precipitation of calcium oxalate. A good fluoride removal ability, low residual oxalate, acceptable final pH, low-cost and simplicity of the process make the present acid-enhanced limestone defluoridation process with OA a potential method for defluoridation of groundwater.     

Achieving stable partial nitritation using endpoint pH control in an SBR treating landfill leachate

The feasibility of using endpoint pH control to achieve stable partial nitritation (PN) in an SBR for landfill leachate treatment was investigated. By imposing a fixed-time anoxia followed by variable-time aeration in an SBR cycle, successful partial nitritation was maintained for 182 days at a nitrogen loading rate of 0.30–0.89 kg/m³/day. The effluent NO₂⁻-N/NH₄⁺-N ratio and the effluent NO₃⁻-N concentration were 1.30 ± 0.22 and 16 ± 9 mg/L, respectively. High free ammonia (FA) and low dissolved oxygen (DO) concentrations were inhibition factors of nitrate formation. The termination of aeration at a suitable endpoint pH was the key to achieve an effluent NO₂⁻-N/NH₄⁺-N ratio close to the stoichiometric value. This endpoint pH control strategy represents practical potentials in the engineered application of combined PN–ANAMMOX processes.     

Biosorption of Co(II) ions from aqueous solution using Chrysanthemum indicum: Kinetics,equilibrium and thermodynamics

The present study investigates the adsorption potential of Chrysanthemum indicum flower in its raw (CIF-R) and biochar (CIF-BC) form for the removal of cobalt ions from aqueous solution. The adsorbents were characterized for their surface area using BET analysis, surface morphology and elemental composition with SEM-EDAX and for the presence of functional groups by FTIR analysis. Batch adsorption experiments were carried out to evaluate the effect of process parameters, viz. pH, adsorbent dosage, initial metal ion concentration, contact time, stirring speed, presence of interfering ions and temperature on the adsorption of Co(II) ion using both the adsorbents. The optimum conditions for maximum removal of Co(II) ion was ascertained to be pH 5 for both adsorbents, adsorbent dose of 4 g/L and 3 g/L, equilibrium time of 60 min and 45 min, respectively, for CIF-R and CIF-BC. The maximum adsorption capacity of CIF-R and CIF-BC was found to be 14.84 mg/g and 45.44 mg/g, respectively, for the removal of Co(II) ion. The mechanism of adsorption was studied using different models of adsorption kinetics, isotherms and thermodynamics. It was inferred that Co(II) adsorption on both CIF-R and CIF-BC followed pseudo-second order kinetics and Langmuir isotherm model with the process being spontaneous and endothermic in nature.     

Use of advance oxidation process to improve the biodegradability of olive oil mill effluents

In this study, recalcitrant total phenol (TPh) and organic matter removal were investigated at olive mill wastewater (OMW) in sequential Coagulation and Fenton system. This study focused on different operational parameters such as pH, H₂O₂, and Fe²⁺ dosages, and [Fe²⁺]/[H₂O₂] ratios. The optimum conditions were determined as; pH = 3; [Fe²⁺] = 2.5 g/L; [Fe²⁺]/[H₂O₂] = 2.5. A higher treatment efficiency was achieved at sequential Coagulation and Fenton system (COD, 65.5%) and TPh, 87.2%), compared to coagulation process (COD, 51.4%; total organic carbon (TOC), 38.6% and total nitrogen (TN) 52.1%). This study demonstrated that the Coagulation and Fenton process has a potential for efficient removal of phenolic pollutants from wastewater.     

Comparison studies of adsorption properties of MgO nanoparticles and ZnO–MgO nanocomposites for linezolid antibiotic removal from aqueous solution using response surface methodology

In this investigation, the adsorption measure of linezolid antibiotic onto MgO nanoparticles and ZnO–MgO nanocomposites were performed. The adsorbents were characterized by different techniques such as XRD, SEM, TEM and BET. The parameters influence such as the pH, adsorbent dosage and temperature was tested and evaluated by Box–Behnken Design combined with response surface methodology. Performing adsorption tests at optimal conditions set as 0.5 g L⁻¹ of adsorbent, pH 10 and 308 K make admit to obtain high adsorption turnover (123.45 and 140.28 mg g⁻¹ for MgO nanoparticles and ZnO–MgO nanocomposites, respectively). A good compromise between predicted and experimental data in this research was observed. The experimental equilibrium data fitting to Langmuir, Freundlich, Tempkin and Dubinin–Radushkevich models indicate that the Langmuir model is a best model for evaluation of adsorption behavior. Kinetic evaluation of experimental data indicated that the adsorption operations followed well pseudo-second-order models. The adsorption capacity of ZnO–MgO nanocomposites is higher than MgO nanoparticles that because of the ZnO–MgO nanocomposites have high specific surface area.     

Pretreatment of municipal landfill leachate by a combined process

Biodegradability enhancement of landfill leachate using air stripping followed by coagulation/ultrafiltration (UF) processes was introduced. The air stripping process obtained a removal efficiency of 88.6% for ammonia nitrogen (NH₄–N) at air-to-liquid ratio of 3500 (pH 11) for stripping 18 h. The single coagulation process increased BOD/COD ratio by 0.089 with the FeCl₃ dosage of 570 mg l^?1 at pH 7.0, and the single UF process increased the BOD/COD ratio to 0.311 from 0.049. However, the combined process of coagulation/UF increased the BOD/COD ratio from 0.049 to 0.43, and the final biological oxygen demand (BOD), chemical oxygen demand (COD), NH₄–N and colour of leachate were 1223.6 mg l^?1, 2845.5 mg l^?1, 145.1 mg l^?1 and 2056.8, respectively, when 3 kDa molecular weight cut-off (MWCO) membrane was used at the operating pressure 0.7 MPa. In ultrafiltration process, the average solution flux (J_V), concentration multiple (M_C) and retention rate (R) for COD was 107.3 l m^?2 h^?1, 6.3% and 84.2%, respectively.     

Investigation of mercury (II) adsorption from aqueous solution onto copper oxide nanoparticles: Optimization using response surface methodology

Response surface methodology was practicable to optimize the mercury (II) removal using copper oxide nanoparticles in an aqueous matrice. The copper oxide nanoparticles structure was performed by TEM, SEM, XRD and BET. The experiment reactions were carried out based on a Box–Behnken design (BBD) and evaluated using RSM. Batch mode tests were conducted to prognosticate the adsorption equilibrium. The three parameters influence on the mercury removal was inquired by a response surface methodological approach. In study, influence of adsorbent dose, pH and temperature on the mercury removal unto copper oxide nanoparticles has been performed. The importance of the independent factors and their interactions were investigated by the ANOVA. The optimum pH, adsorbent dose and temperature were obtained to be 9.0, 0.05 g and 278 K, respectively.     

Development and physicochemical characterization of a new magnetic nanocomposite as an economic antibiotic remover

Maghemite (ϒ-Fe₂O₃) nanoparticles were impregnated to nanoporous carbon obtained from tomato waste (TWNC). The prepared magnetic composite (MTWNC) was characterized and used to remove tetracycline (TC) from water and then easily be separated from the medium by a magnetic technique. The morphologies and surface chemistries of both magnetic and non-magnetic nanoporous carbons were studied by FTIR, XRD, SEM, SEM-EDX, VSM, BET surface area, proximate and elemental analysis determinations. Batch adsorption studies were carried out and the effects of pH, initial TC concentration, adsorbent dose, ionic strength and temperature were investigated. The adsorption kinetics of TC on MTWNC could be expressed well by the pseudo-second order model, and sorption isotherms were described by Langmuir equation with maximum adsorption capacity of 60.60 mg/g at pH 4 and 50 °C. Thermodynamic parameters showed that the adsorption of TC onto MTWNC was feasible, spontaneous and endothermic. Furthermore, the recyclability of the adsorbent was tested with 0.01 M NaOH solution, and the results show that the synthesized composite adsorbent could be employed repeatedly in wastewater treatment.     

Ion exchange membrane-assisted electro-activation of aqueous solutions: Effect of the operating parameters on solutions properties and system electric resistance

The properties of electro-activated (EA) aqueous solutions as well as the dynamics of their changes were considered in the current study using aqueous solutions of NaCl and NaHCO₃. The concentrations of the salt solutions were 0.5, 0.25, 0.125 and 0.05 M. The tests were performed at the DC current densities of 25, 37.5, and 50 Å/m². The electro-activation reactor consisted of three individual cells assembled together and separated by anion-exchange (AEM) and cation-exchange (CEM) membranes. During the experiments, four configurations of the membrane placements and solutions concentrations were studied. The obtained results showed the dynamics of the electro-activation process that allows obtaining electro-activated solutions with targeted properties such as pH and oxydo-reduction potential (ORP). It was possible to obtain electro-activated solutions at the anodic side (acid anolyte) with pH of 3.0, 3.5, and 4.0 and ORP of +1100 ± 15 mV when NaCl solution was used as electrolyte. Furthermore, several types of electro-activated solutions with high redox potential (ORP = +921 ± 12 mV) and neutral pH (6.48 ± 0.05) were obtained on the anode side when sodium carbonate was used. At the same time, two types of solutions, one with acid pH (2.14 ± 0.14) and the other one with alkaline pH (10.46 ± 0.03) with ORP = +689 ± 10 and 110 ± 21 mV, respectively, were obtained in the central compartment which considered as electro-activated solutions obtained by means of noncontact electro-activation.