Detoxification of hexavalent chromium in wastewater containing organic substances using simonkolleite-TiO2 photocatalyst

Innovative simple method for the preparation of simonkolleite-TiO₂ photocatalyst with different Zn contents was achieved. The prepared photocatalysts were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), FT-IR, Raman and diffuse reflectance spectroscopy techniques. The photocatalytic activities of the materials were evaluated for the simultaneous detoxification of hexavalent chromium (Cr(VI)) and oxidation of organic compounds commonly present in wastewater under simulated solar light. The best photoreduction efficiency of Cr(VI) has been achieved at 1000 ppm simonkolleite-TiO₂ photocatalyst of 5% Zn/TiO₂ weight ratio, and pH value of 2.5 to enhance the adsorption onto catalyst surface. Photoreduction was significantly improved by using formic acid as holes scavenger owing to its chemical adsorption on the catalyst surface. Finally, 100% photoreduction of Cr(VI) could be achieved using formic/simonkolleite-TiO₂ systems under sunlight.     

Preparation of iodine doped titanium dioxide to photodegrade aqueous bisphenol A under visible light

Highly photoactive iodine-doped titanium dioxide (I-doped TiO₂) photocatalysts were synthesized to degrade aqueous bisphenol A (BPA) under irradiation by visible light and sunlight. The band gap energies of TiO₂ and I-doped TiO₂ (I/Ti mole ratio = 0.5%) were 3.01 and 3.04, and the BPA photodegradation rate constants were 1.61, and 5.11 h⁻¹, respectively. The most probable reaction mechanism was proposed to involve IO₄⁻ and IO₃⁻ as electron acceptors that generate an inductive effect, increasing the photocatalytic efficiency of TiO₂. Results indicated that I-doped TiO₂ not only acted favorably as a photocatalyst, but also exhibited considerable mineralization effects. In addition, a recycling test after ten experiments demonstrated the stability and reusability of the photocatalyst.     

Mesoporous simonkolleite–TiO2 nanostructured composite for simultaneous photocatalytic hydrogen production and dye decontamination

In the present work, mesoporous simonkolleite–TiO₂ composite was prepared with sol–gel method. The composite photocatalysts were characterized by X-ray diffraction (XRD), diffuse reflectance spectroscopy (DRS), and Raman spectroscopy. Also, surface area and particle size were analyzed using BET equation. The photocatalytic hydrogen production with simultaneous decolorization of Remazole Red (F3B) dye was investigated over TiO₂ and simonkolleite–TiO₂ composite under UV–vis light irradiation. It was worthy to be noted that the rate of hydrogen production over simonkolleite–TiO₂ is higher that produced over TiO₂. The maximum amount of photocatalytic-produced hydrogen was 2.1 mmol and 3.3 mmol within 240 min using TiO₂ and simonkolleite–TiO₂ composite, respectively. The specific production rate of hydrogen from photocatalytic conversion of dye was calculated. Improvement of apparent quantum yield (22.07%) after 5 h was achieved upon addition of simonkolleite to TiO₂. This high apparent quantum yield proves that the system proposed in this study could be a hopeful approach toward using sunlight energy as outlook energy source. The obtained results suggested that a new process for H₂ production from wastewater could be achieved. The process also provides a method for degradation of organic pollutants with simultaneous H₂ production.     

Optimizing the preparation parameters of mesoporous nanocrystalline titania and its photocatalytic activity in water: Physical properties and growth mechanisms

Titania nanomaterial with an anatase structure and 5.6 nm crystallite size and 280.7 m² g⁻¹ specific surface areas had been successfully prepared by sol–gel/hydrothermal route. The effect of pH as a type of autoclave and calcination was studied. Crystallite size and phase composition of the prepared samples were identified. X-ray diffraction analyses showed the presence of anatase with little or no rutile phases. The crystallite size of the prepared TiO₂ with acidic catalyst was both smaller than that prepared with basic catalyst, and was increasing after acidic calcinations by a factor 4–5. Basic calcinations produced a specific increase of 1.5. Rutile ratio and the particle size were increased after calcination at 500 °C. However, TiO₂ powder synthesized using a basic catalyst persisted the anatase phase and a loosely aggregation of particles. Anatase TiO₂ as prepared with acidic catalyst in Teflon lined stainless steel autoclave demonstrated the highest photocatalytic activity for degradation of 2,6-dichlorophenol-indophenol under ultraviolet irradiation with t_½ 0.8 min.     

Thermal characterization of fly ash from one municipal solid waste incinerator (MSWI) in Shanghai

This study aims to develop a methodology for the thermal characterization of MSWI fly ash. We performed TGA–DTA and component variation analysis, microstructure transfer of sintered fly ash, as well as leaching toxicity, volatilization ratio and specification transformation of heavy metals as a function of temperature. It is found that content of crystal phases first increases between room temperature and 800 °C and then decreases between 800 °C and 1200 °C, while that of glass phases registers a reverse trend. Fly ash registers a SiO₂–Al₂O₃–metal oxides system and its content of glass phases is around 57%. Increase of sintering temperature between 600 °C and 1200 °C is conducive to the reduction of soluble As, Cd, Cu, Hg, Pb, Ni and Zn, while content of soluble Cr increases as temperature rises from 800 °C to 1200 °C.     

Calorimetric behaviors of N2H4 by DSC and superCRC

The objective of this study is to obtain information about the thermal decomposition behaviors of hydrazine (N₂H₄) caused by metals, using differential scanning calorimeter (DSC) and SuperCRC. The DSC measurements revealed that the exothermic reactions of N₂H₄ were caused by the reaction conditions such as the type of cells; the T_DSC with a gold pan is 485.2 K and that with a glass capillary is 620.5 K. Besides, the activation energy of the thermal decomposition of N₂H₄, calculated from the Kissinger and Ozawa methods, were found to be about 38±2 kJ mol⁻¹ in the gold pan and 141±8 kJ mol⁻¹ in the glass capillary. Moreover, a heat flow profile was observed with SuperCRC during the mixing of N₂H₄ and the metal ion solution at 298 K. The maximum heat flow was related to the metal ion oxidative characters. The higher oxidative characters would provide a faster acceleration for the exothermic behavior than the lower oxidative ions. Based on this study, Mn(VII) and Cr(VI) were considered to exhibit strongly oxidative characteristics during mixing with N₂H₄.     

Effect of ultrasound irradiation and Ni-loading on properties and performance of CeO2-doped Ni/clinoptilolite nanocatalyst used in polluted air treatment

In this research nanocatalysts containing 5, 10 and 15 wt.% of Ni, dispersed by sonication over CeO₂–clinoptilolite composite support were compared toward total oxidation of toluene. Their catalytic performance at different temperatures between 150 and 350 °C was studied based on the oxidative destruction of toluene. The results indicated that the activity of Ni/CeO₂–clinoptilolite nanocatalyst for toluene oxidation increased from 33 to 44% at 250 °C by employing sonochemical method in synthesis of catalyst. Meanwhile, the catalytic activity was also improved when Ni content was increased from 5 to 10 and 15 wt.%. With the aid of several characterization techniques like XRD, FESEM, PSD, EDX, BET and FTIR, the correlation between nanocatalyst structure and its activity was addressed. It is indicated that sonochemical method can lift the catalytic activity due to the better dispersion of catalyst active components and also higher surface area. Among sonicated samples, 15 wt.% Ni nanocatalyst showed the highest toluene oxidation due to the better dispersion of catalyst active components and hence to more effective catalytic sites.     

Synthesis of CuO nanoparticles through green route using Citrus limon juice and its application as nanosorbent for Cr(VI) remediation: Process optimization with RSM and ANN-GA based model

In present investigation, an attempt has been made for the synthesis of cupric oxide nanoparticles (CuONPs) through a green route by utilizing lemon juice extract as a bioreductant. The synthesized CuONPs were characterized through UV–visible spectroscopy, Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), field-emission scanning electron microscopy (FE-SEM) and transmission electron microscopy (TEM). The CuONPs were utilized for Cr(VI) removal from water through adsorption method in batch mode at different initial Cr(VI) concentration, pH, temperature and CuONPs dosage. The maximum uptake capacity of CuONPs was found to be 16.63 mg of Cr(VI)/g at pH 4.0. Implementation of response surface methodology (RSM) followed by artificial neural network hybridized with genetic algorithm (ANN-GA) approach has resulted maximum Cr(VI) adsorption of 98.8% under the optimized conditions of initial metal concentration 22.5 mg/L, pH 3.81, CuONPs dose 1.28 g/L and temperature 37.1 °C. Under optimum conditions, adsorption isotherm study was conducted, which showed that the fitness of experimental data was well achieved with Langmuir isotherm model illustrating monolayer pattern of adsorption. Thermodynamic study revealed that the process was spontaneous and endothermic in nature, while adsorption kinetics was best explained by pseudo-second order kinetic model.     

Decolorization and degradation of acid dye with immobilized titania nanoparticles

This paper addresses the decolorization and degradation of acid dye by a heterogeneous photocatalytic process using immobilized nano-sized TiO₂ particles as the photocatalyst. Sackcloth fiber was used as a support to immobilize the nano-sized TiO₂ photocatalyst. The structural properties of the immobilized photocatalyst were characterized by XRD, SEM and EDX. UV–Vis absorption spectroscopy and the measurement of the chemical oxygen demand (COD) were also used for the process performance studies. The XRD results did not show significant changes in the structure of P25 as a consequence of the immobilization procedure. The formation of titania crystallites in the sackcloth fiber was confirmed by SEM/EDX. The photocatalytic activities of TiO₂-coated sackcloth fiber catalyst were evaluated using Acid Black 26 as a model organic contaminant and using UV-A radiation. Experimental results showed that after 60 min, the degradation of Acid Black 26 with the immobilized TiO₂ particles was higher than that with plain TiO₂. Based on the COD results, after 3 h, the TiO₂-coated sackcloth fiber effectively decomposed all of the organic compounds present in dye solution under the studied experimental conditions. The effects of the oxidant H₂O₂, initial dye concentration and pH on the photocatalytic degradation were also investigated. The presence of CO₃^2? as a dissolved inorganic anion had the highest inhibitory effect on the decolorization of the dye, when compared with the other anions investigated. Kinetics analysis indicates that the photocatalytic decolorization rate of Acid Black 26 can be described by a pseudo-first-order model.     

An improved method of removal for high concentrations of NO by electro-scrubbing process

In the Ag(II)/Ag(I) redox mediator integrated scrubber system, NO reacts with the Ag(II) ions produced by the electrochemical oxidation of Ag(I) in an electrochemical cell present in the scrubbing solution (aqueous HNO₃ acid) to form NO₂. This NO₂ is then absorbed into the scrubbing solution and degraded to nitrate. Numerous experimental runs were carried out to evaluate the feasibility of the integrated system to treat industrial waste gases containing high NO_x levels. The results showed that the levels of NO and NO_x removal increased with increasing Ag(II) loading and contact time. Under optimized conditions, 93.5% and 73.3% of the NO and NO_x, respectively, were removed by a single stage gas scrubber with 1.62 g L^?1 Ag(II) operating at 25 °C and atmospheric pressure.     

Disintegration of waste activated sludge by different applications of Fenton process

Oxidative disintegration of municipal waste activated sludge (WAS) using conventional Fenton (Fe²⁺ + H₂O₂, CFP) and Fenton type (Fe⁰ + H₂O₂, FTP) processes was investigated and compared in terms of the efficiency of sludge disintegration and enhancement of anaerobic biodegradability. The influences of different operational variables namely sludge pH, initial concentration of Fe²⁺ or Fe⁰, and H₂O₂ were studied in detail. The optimum conditions have been found as catalyst iron dosage = 4 g/kg TS, H₂O₂ dosage = 40 g/kg TS and pH = 3 within 1 h oxidation period for both CFP and FTP. Kinetics studies were performed under optimal conditions. It was determined that the sludge disintegration was happened in two stages by both processes: rapid and subsequent slow disintegration stages and rapid sludge disintegration stage can be described by a zero-order kinetic model. The effects of oxidative sludge disintegration under the optimum conditions on anaerobic digestion were experienced with biochemical methane potential (BMP) assay in batch anaerobic reactors. Total methane production in the CFP and FTP pre-treated reactors increased by 26.9% and 38.0%, relative to the untreated reactor (digested the raw WAS). Furthermore, the total chemical oxygen demand reductions in the pre-treated reactors were improved as well.     

Growing Carbon Nanotube on Aluminum Oxides: An Inherently Safe Approach for Environmental Applications

Using micron-sized Al₂O₃ particles as carriers to grow carbon nanotubes (CNTs) under 700°C atmosphere of methane and hydrogen after pre-planted catalysts of Fe–Ni nanoparticles, those composite CNTs (CCNTs) have demonstrated several unique properties compared to CNTs—medium specific surface area and zeta potential, high adsorption capacity for metal ions, high recovery rate by acids, low decomposition heat for exothermal reaction, and so on. The adsorption behaviours of Pb²⁺, Cu²⁺ and Cd²⁺ in aqueous solutions by CCNTs are in good agreement with the Langmuir adsorption isotherm and second order kinetic model with maximum individual adsorption capacities of 67.11, 26.59 and 8.89 mg g⁻¹. The individual and competitive adsorption behaviours indicated that the preference order of adsorption were Pb²⁺ > Cu²⁺ > Cd²⁺ for aluminum oxides, activated carbon, commercial CNTs, and CCNTs as well as other researchers’ CNTs. We suggest that future development of CNTs to combine with metals and/or other materials, such as TiO₂, should consider attached to carriers or surface in order to avoid concerns on environment, health and safety. Thus, growing CNTs on Al₂O₃ particles to form CCNTs is an inherently safe approach for many promising environmental applications.     

Refinery wastewater degradation with titanium dioxide,zinc oxide,and hydrogen peroxide in a photocatalytic reactor

This paper presents the photo-catalytic degradation of real refinery wastewater from National Refinery Limited (NRL) in Karachi, Pakistan, using TiO₂, ZnO, and H₂O₂. The pretreatment of the refinery effluent was carried out on site and pretreated samples were tested at 32–37 °C in a stirrer bath reactor by using ultra-violet photo oxidation process. The degradation of wastewater was measured as a change in initial chemical oxygen demand (COD) and with time. Optimal conditions were obtained for catalyst type, and pH. The titanium dioxide proved to be very effective catalysts in photo-catalytic degradation of real refinery wastewater. The maximum degradation achieved was 40.68% by using TiO₂ at 37 °C and pH of 4, within 120 min of irradiations. When TiO₂ was combined with H₂O₂ the degradation decreased to 25.35%. A higher reaction rate was found for titanium dioxide. The results indicate that for real refinery wastewater, TiO₂ is comparatively more effective than ZnO and H₂O₂. The experiments indicated that first-order kinetics can successfully describe the photo-catalytic reaction. The ANOVA results for the model showed satisfactory and reasonable adjustment of the second-order regression model with the experimental data. The ANOVA results also showed that pH is significant than reaction time and catalyst dosage of TiO₂; and in case of ZnO, reaction time is significant than pH and catalyst dosage. This study proves that real refinery wastewater reacts differently than synthetic refinery wastewater, oil field produced water or oil water industrial effluent.     

Prevalence of work-site injuries and relationship between obesity and injury among U.S. workers: NHIS 2004–2012

Introduction: Studies have reported associations between obesity and injury in a single occupation or industry. Our study estimated the prevalence of work-site injuries and investigated the association between obesity and work-site injury in a nationally representative sample of U.S. workers. Methods: Self-reported weight, height, and injuries within the previous three months were collected annually for U.S. workers in the National Health Interview Survey (NHIS) from 2004–2012. Participants were categorized as normal weight (BMI: 18.5–24.9 kg/m²), overweight (BMI: 25.0–29.9), obese I (BMI: 30.0–34.9), and obese II (BMI: 35 +). The prevalence of injury and prevalence ratios from fitted logistic regression models was used to assess relationships between obesity and injury after adjusting for covariates. Sampling weights were incorporated using SUDAAN software. Results: During the 9-year study period from 2004 to 2012, 1120 workers (78 workers per 10,000) experienced a work-related injury during the previous three months. The anatomical sites with the highest prevalence of injury were the back (14.3/10,000 ± 1.2), fingers (11.5 ± 1.3), and knees (7.1 ± 0.8). The most common types of injuries were sprains/strains/twists (41.5% of all injuries), cuts (20.0%), and fractures (11.8%). Compared to normal weight workers, overweight and obese workers were more likely to experience work-site injuries [overweight: PR = 1.25 (95% CI = 1.04–1.52); obese I: 1.41 (1.14–1.74); obese II: 1.68 (1.32–2.14)]. These injuries were more likely to affect the lower extremities [overweight: PR = 1.48, (95% CI = 1.03–2.13); obese I: 1.70 (1.13–2.55); obese II: 2.91 (1.91–4.41)] and were more likely to be due to sprains/strains/twists [overweight: PR = 1.73 (95% CI = 1.29–2.31); obese I: PR = 2.24 (1.64–3.06); obese II: PR = 2.95 (2.04–4.26)]. Conclusions: Among NHIS participants, overweight and obese workers were 25% to 68% more likely to experience injuries than normal weight workers. Practical applications: Weight reduction policies and management programs may be effectively targeted towards overweight and obese groups to prevent or reduce work-site injuries.     

Use of advance oxidation process to improve the biodegradability of olive oil mill effluents

In this study, recalcitrant total phenol (TPh) and organic matter removal were investigated at olive mill wastewater (OMW) in sequential Coagulation and Fenton system. This study focused on different operational parameters such as pH, H₂O₂, and Fe²⁺ dosages, and [Fe²⁺]/[H₂O₂] ratios. The optimum conditions were determined as; pH = 3; [Fe²⁺] = 2.5 g/L; [Fe²⁺]/[H₂O₂] = 2.5. A higher treatment efficiency was achieved at sequential Coagulation and Fenton system (COD, 65.5%) and TPh, 87.2%), compared to coagulation process (COD, 51.4%; total organic carbon (TOC), 38.6% and total nitrogen (TN) 52.1%). This study demonstrated that the Coagulation and Fenton process has a potential for efficient removal of phenolic pollutants from wastewater.     

Workers' compensation loss prevention representative contact and risk of lost-time injury in construction policyholders

IntroductionInsurance loss prevention (LP) representatives have access and contact with businesses and employees to provide targeted safety and health resources. Construction firms, especially those smaller in size, are a high-risk population. This research evaluated the association between LP rep contact and risk for lost-time injuries in construction policyholders.MethodsWorkers' compensation data were utilized to track LP rep contact with policyholders and incidence of lost-time injury over time. Survival analysis with repeated events modeling calculated hazard ratios (HR) and 95% confidence intervals (CI).ResultsCompared no LP contact, one contact was associated with a 27% reduction of risk (HR = 0.73, CI = 0.65–0.82), two with a 41% (HR = 0.59, CI = 0.51–0.68), and three or more contacts with a 28% reduction of risk (HR = 0.72, CI = 0.65–0.81).ConclusionsLP reps appear to be a valuable partner in efforts to reduce injury burden. Their presence or contact with policyholders is consistent with reduction in overall incidence of lost-time injuries.Practical applicationsReduction in lost-time injuries, resulting in reduced workers' compensation costs for policyholders and insurance companies, builds a business-case for safety and injury prevention. LP reps are often a low or no-cost benefit for insurance policyholders and may be an important injury prevention resource for small firms and/or those with lack of safety resources and staff.     

pH-conditioning for simultaneous removal of arsenic and iron ions from groundwater

The effects of some commonly used pH conditioners, viz., lime, banana ash, the carbonate and the bicarbonate of sodium and potassium and their binary mixture, on simultaneous removal of arsenic and iron ions from water have been studied. KHCO₃ has been found to be the most suitable pH conditioner for the purpose. About 80 mg/L KHCO₃ can remove both arsenate and iron ions from initial 250 μg/L and 20 mg/L to below their respective guideline values of the WHO for drinking water, retaining the final pH in the acceptable range for drinking. The simultaneous removal of arsenate and iron by the pH-conditioners decreases in the order: Lime > KHCO₃ > NaHCO₃ > K₂CO₃ > Na₂CO₃ > ash. However, lime requires post-treatment correction of highly alkaline pH. The arsenate ion is removed predominantly through goethite or ferrihydrite in the presence of the bicarbonates and through ferric hydroxide in the presence of the more alkaline pH-conditioners. KHCO₃ is more advantageous over the more basic substances including NaHCO₃, because with it, one not only needs the smallest dose but also can avoid careful adjustment of the dose for regulating the initial and the final pH. The paper clearly demonstrates the potential of KHCO₃ to substitute the currently used pH-conditioners, viz., ash, lime and NaHCO₃ for simultaneous removal of arsenate and iron ions.     

Biosorption of zinc(II) on rapeseed waste: Equilibrium studies and thermogravimetric investigations

The removal of heavy metals from aqueous effluents so as to avoid their toxic, bioaccumulation and biomagnification effects to humans and environment is usually realized by means of physical, chemical treatment, and biological processes. The aim of this study is to evaluate the potential of rapeseed waste from biodiesel production as a biosorbent for Zn(II) ions.The ability of the rapeseed waste for Zn(II) biosorption exhibited a maximum at pH 4.5–5. The removal efficiency of Zn(II) from solution with an initial concentration of 72 mg L⁻¹ varied from 39% to 89% for an increase of the rapeseed waste dose from 2 to 30 g L⁻¹. The amount of Zn(II) retained on the tested rapeseed increased with increasing metal ion concentration, but the Zn(II) sorption percentage decreased. The equilibrium data are fitted to the Langmuir isotherm better than to the Freundlich isotherm. The kinetics of Zn(II) biosorption process follows a pseudo-second order model. The thermal stability of the rapeseed before and after Zn(II) biosorption was studied by thermogravimetric analysis. It was found that the zinc loaded rapeseed exhibits a better initial thermal stability than the original rapeseed, presumably due to the cross linking generated by the intermolecular complexation of Zn(II) ions. In both cases, the thermal decomposition takes place according to some reassembling kinetic models, in two phases with order n reactions. The results of this study strongly suggest the possibility to use rapeseed as an effective biosorbent for Zn(II) ions removal from aqueous effluents (municipal/industrial wastewaters).     

Artificial neural network modelling of As(III) removal from water by novel hybrid material

The present study reported a method for removal of As(III) from water solution by a novel hybrid material (Ce-HAHCl). The hybrid material was synthesized by sol–gel method and was characterized by XRD, FTIR, SEM–EDS and TGA–DTA. Batch adsorption experiments were conducted as a function of different variables like adsorbent dose, pH, contact time, agitation speed, initial concentration and temperature. The experimental studies revealed that maximum removal percentage is 98.85 at optimum condition: pH = 5.0, agitation speed = 180 rpm, temperature = 60 °C and contact time = 80 min using 9 g L⁻¹ of adsorbent dose for initial As(III) concentration of 10 mg L⁻¹. Using adsorbent dose of 10 g L⁻¹, the maximum removal percentage remains same with initial As(III) concentration of 25 mg L⁻¹ (or 50 mg L⁻¹). The maximum adsorption capacity of the material is found to be 182.6 mg g⁻¹. Subsequently, the experimental results are used for developing a valid model based on back propagation (BP) learning algorithm with artificial neural networking (BP-ANN) for prediction of removal efficiency. The adequacy of the model (BP-ANN) is checked by value of the absolute relative percentage error (0.293) and correlation coefficient (R² = 0.975). Comparison of experimental and predictive model results show that the model can predict the adsorption efficiency with acceptable accuracy.     

Biosorption of Co(II) ions from aqueous solution using Chrysanthemum indicum: Kinetics,equilibrium and thermodynamics

The present study investigates the adsorption potential of Chrysanthemum indicum flower in its raw (CIF-R) and biochar (CIF-BC) form for the removal of cobalt ions from aqueous solution. The adsorbents were characterized for their surface area using BET analysis, surface morphology and elemental composition with SEM-EDAX and for the presence of functional groups by FTIR analysis. Batch adsorption experiments were carried out to evaluate the effect of process parameters, viz. pH, adsorbent dosage, initial metal ion concentration, contact time, stirring speed, presence of interfering ions and temperature on the adsorption of Co(II) ion using both the adsorbents. The optimum conditions for maximum removal of Co(II) ion was ascertained to be pH 5 for both adsorbents, adsorbent dose of 4 g/L and 3 g/L, equilibrium time of 60 min and 45 min, respectively, for CIF-R and CIF-BC. The maximum adsorption capacity of CIF-R and CIF-BC was found to be 14.84 mg/g and 45.44 mg/g, respectively, for the removal of Co(II) ion. The mechanism of adsorption was studied using different models of adsorption kinetics, isotherms and thermodynamics. It was inferred that Co(II) adsorption on both CIF-R and CIF-BC followed pseudo-second order kinetics and Langmuir isotherm model with the process being spontaneous and endothermic in nature.