开口钢管内甲烷爆炸火焰厚度和压力发展特征

通过搭建长为20m、截面为0.08m×0.08m的非绝热开口钢管,研究了甲烷与空气预混气体发生爆炸后的火焰和压力发展特征。实验结果表明:火焰信号最强的时刻对应于火焰前锋反应区内某时刻,而火焰信号起始上升时刻与火焰前锋预热区起始时刻接近,应选择某点火焰信号起始上升时刻作为该点的火焰到达时间。随着远离点火源距离的增加,火焰厚度呈现先变薄后变厚的变化趋势,最大超压呈现先减小、后增大、再减小的趋势,火焰传播速度则呈先增大后减小的变化过程。非绝热开口钢管的实验条件对爆炸超压和火焰传播速度的影响较大。研究成果可为甲烷爆炸致灾机制及防控的研究提供参考。     

Effects of obstacles and deposited coal dust on characteristics of premixed methane–air explosions in a long closed pipe

An experimental system including pressure transducer, electric spark ignition device, data acquisition and control unit was set up to investigate methane–air explosions in a horizontal pipe closed at both ends with or without the presence of obstacles and deposited coal dust. The experimental results show that explosion characteristics depended on the methane content, on the layout of obstacles, and on the deposited coal dust. Pressure fluctuation with a frequency of 150 Hz appeared in its crest when the methane content was close to the stoichiometric ratio (9.5% methane percentage by volume). The pressure rise rate increased locally when a single obstacle was mounted in the pipe, but it had little effect on the pressure peak. Repeated obstacles mounted in the pipe caused the pressure to rise sharply, and the mean maximum explosion overpressure increased with the increase of the obstacle’s number. The amplitude of pressure fluctuation was reduced when deposited coal dust was paved in the bottom of the pipe. However, when repeated obstacles were arranged inside, the maximum overpressures were higher with coal dust deposited than pure gas explosions.     

缝洞型管道瓦斯爆炸特性数值模拟研究

为探究采空区遗煤、松散破碎岩块对瓦斯爆炸的影响,建立缝洞型管道模型,采用数值模拟与理论分析结合方法研究采空区内缝洞型管道内瓦斯爆炸的传播规律及管道长径比对瓦斯爆炸过程中速度与冲击波的影响。研究结果表明:在缝洞型结构内,随着火焰沿管道向前传播,各监测点速度逐渐变大、压力先增加后降低,而压力上升速率则表现出不规则的变化;缝洞结构加剧了火焰燃烧的剧烈程度,提高了管道内各监测点的温度峰值;在缝洞型管道内随长径比r增加,各监测点最大压力峰值以及速度大小依次降低。     

点火位置对独头巷道中瓦斯爆炸超压的影响

运用AutoReaGas爆炸仿真模拟器研究了独头巷道中点火位置对瓦斯爆炸后果的影响。结果表明,在本计算条件下,爆炸静态超压随着距离的增加而减小,爆炸动压随着距离的增大而增大,点火位置对爆炸后果有重要影响,点火位置离封闭端越近,各个测点上所得到的超压越大。     

爆炸性气体在连续拐弯管道中传播特性的实验研究

针对复杂燃气管网燃气爆炸致灾严重,传播规律复杂的问题,利用实验室加工成的连续拐弯管道,模拟研究了复杂燃气管网爆炸性气体通过连续拐弯管道时的火焰传播速度、爆炸波超压变化情况。研究结果表明,当整个管道内充满瓦斯气体时,通过连续拐弯后,火焰传播速度和爆炸波超压值产生显著变化,在连续拐弯管道拐弯处为一扰动源,诱导附加湍流,气流湍流度增大,管道拐弯增加了燃烧区的湍流度,火焰燃烧产生加速度,加速燃烧产生更大能量以推动加速传播。研究结果对指导现场如何防治复杂燃气管网气体爆炸,减轻爆炸的威力具有重要作用。     

Experimental study on the mitigation via an ultra-fine water mist of methane/coal dust mixture explosions in the presence of obstacles

In this paper, experimental investigations were performed for the mitigation via an ultra-fine water mist of methane/coal dust mixture explosions in the presence of obstacles to reveal the effects of the obstacles in this scenario. Two PCB piezo-electronic pressure transducers were used to acquire the pressure history, a Fastcam Ultima APX high-speed video camera was used to visualize both the process of the mixture explosion and its mitigation. The diameters of the coal dust, the types of obstacles and the volumes of ultra-fine water mist were varied in the tests. The parameters of the explosion overpressure and the range of critical volume flux of the ultra-fine water mist for explosion mitigation were determined. The results show that the mixture explosion and its mitigation are primarily influenced by the number, shape and set locations of the obstacles. When the volume flux of the water mist is larger than a certain amount, the mixture explosions and the effects of obstacles can be completely mitigated with the ultra-fine water mist.     

不同含水率煤尘在瓦斯爆炸诱导下爆炸传播规律研究

为了探究不同含水率煤尘在瓦斯爆炸诱导下的爆炸传播规律,利用自行搭建的直管瓦斯爆炸诱导煤尘二次爆炸实验系统,从冲击波压力和火焰传播速度2个方面,研究了不同含水率沉积煤尘在瓦斯爆炸诱导下的爆炸传播规律和原因。研究结果表明:当煤尘含水率小于40%时,管道内沉积煤尘会在瓦斯爆炸诱导下产生二次爆炸,同时沉积煤尘总量一定时,沉积煤尘二次爆炸产生的冲击波超压峰值和火焰传播速度随着煤尘含水率的增加先增大后减小;当沉积煤尘含水率为20% 时,煤尘二次爆炸产生的冲击波超压峰值、火焰传播速度峰值达到最大值,分别为1.657 MPa和468.060 m/s;当沉积煤尘含水率大于40%时,沉积煤尘无法产生二次爆炸,此时爆炸产生的威力小于单一瓦斯爆炸,火焰传播速度衰减较无煤尘的瓦斯爆炸更快,沉积煤尘起到抑制瓦斯爆炸传播的作用。研究结果可以为防治煤尘二次爆炸提供理论依据。     

球接管容器气体爆炸尺寸效应的试验研究与数值分析

为了解尺寸对球形容器连接管道甲烷-空气混合物爆炸的影响规律,利用Fluent软件,采用κ-ε湍流模型、涡耗散模型(简称EDC模型)、壁面热耗散、热辐射模型及SIMPLE算法,建立了球形容器连接管道内甲烷-空气混合物爆炸的数值模型,对容器与管道内甲烷-空气预混气体爆炸的尺寸效应进行了数值模拟。结果表明:随管道内径增大,球形容器内最大爆炸压力逐渐增大,管道末端最大爆炸压力变化无明显规律;而随管道长度增加,球形容器内最大爆炸压力逐渐减小;改变管道内径,较大体积球形容器内最大爆炸压力均大于较小体积球形容器内最大爆炸压力,最大爆炸压力上升速率的规律则相反,容器体积对管道末端最大爆炸压力的影响无明显规律。     

Effect of bifurcation on premixed methane-air explosion overpressure in pipes

It is well known that bifurcation structures have a significant influence on gas explosions in pipelines or roadways. In this work, three different types of bifurcation, namely, bifurcation with two right angles (BTRAs), bifurcation with two obtuse angles (BTOAs), and bifurcation with an obtuse angle and an acute angle (BOAA), were used to study the effect of bifurcation on premixed methane–air explosion overpressure in pipes. The effect of the position of bifurcation on gas explosions was also discussed. Our results suggest that the peak overpressure evolution in pipes exhibits a downtrend before the bifurcation, a sharp increase after the bifurcation until reaching the maximum, and a downward trend when propagating into the pipe end. It was also found that gas-explosion propagation was affected by the joint action of turbulence induced by obstacles and the abrupt increase of the cross-sectional area. In addition, the bifurcation’s position had only a small effect on the maximum peak overpressure in pipes.     

Insight into vented explosion mechanism and premixed flame dynamics in linked vessels: Influence of membrane thickness and blocking rate

To effectively prevent and mitigate explosion hazards and casualties, relief venting of flammable gas explosions has been applied in production processes in a broad variety of industries. This work conducted fully vented experiments to investigate the influence of venting membrane thickness, and partially vented experiments to investigate the influence of baffle blocking rate on the explosion characteristics of 9.5 vol% methane-air mixtures in linked vessels with a 0.5 m long vented duct. Results indicate that the membrane thickness and blocking rate for the two types of vented explosions significantly affected the explosion overpressure. The smaller the membrane thickness and blocking rate, the lower the explosion overpressure. Secondary explosions were observed in the vented duct through experiments and a weaker explosion flame appeared at a small blocking rate of 20%. With the further increase in the blocking rate, the flame became extremely weak, and no secondary explosions occurred. The overpressure evolution process at different positions in the explosion duct and secondary explosion phenomenon in the vented duct were investigated. This work could probably serve as an important reference for the selection of technical parameters of explosion venting in the practical industrial processes.     

Calculating overpressure from BLEVE explosions

Although a certain number of authors have analyzed the prediction of boiling liquid expanding vapour explosion (BLEVE) and fireball effects, only very few of them have proposed methodologies for predicting the overpressure from such explosions. In this paper, the methods previously published are discussed and shown to introduce a significant overestimation due to the erroneous thermodynamic assumptions—ideal gas behaviour and isentropic vapour expansion—on which they are based (in fact, they give the maximum value of overpressure which can be caused by a BLEVE). A new approach is proposed, based on the—more realistic—assumption of an adiabatic and irreversible expansion process; the real properties of the substance involved in the explosion are used. The two methods are compared through the application to a given case.     

Experimental research into effects of obstacle on methane-coal dust hybrid explosion

An experimental system including pressure transducer, data acquisition card, computer and electric spark ignition device was set up to research methane-coal dust hybrid explosions in closed tubes with different types of obstacles inside. Its dynamic response time was less than a millisecond and the test precision was 0.1%. The experimental results show that the obstacles had great effects on the explosion characteristics in the tube. Hollow obstacles linked with inner wall of the tube induced faster pressure rising than installed center blocked solid obstacles. Obstacles with more sharp corner induce more violent explosions. The most dangerous explosion occurred when spacing between obstacles almost equaled the inner diameter of the tube for the same size obstacle.     

Overpressure characteristics of aluminium dust explosion vented through a relief pipe

A parametric experimental study of an aluminium dust explosion, initiated in a vessel and vented through a relief pipe, was performed. The aim is to clarify the overpressure characteristics in a vessel and relief pipe, during aluminium dust explosion venting, especially when a burn-up phenomenon occurs. For a vessel of fixed size, the influence of pipe diameter and pipe length on burn-up was discussed. Results demonstrate that burn-up occurs shortly after flame only enters the initial part of the relief pipe when the original dust concentration in the vessel is at relatively high level, which is usually higher than the optimum concentration obtained from the confined vessel. When burn-up occurs, the maximal overpressure continues to increase rather than to decay along the initial part of the relief pipe. If burn-up is vigorous, a second peak on overpressure-time curve in the vessel could appear. By adding 0.1 g aluminium powders on the membrane, the second overpressure peak may even surpass the first peak. Extending pipe lengths can strengthen the overpressures around the position where burn-up occurs in the relief pipe. Reducing the pipe diameter can increase the burn-up severity in the relief pipe owing to the increased dust concentration and the pressure accumulation.     

Influence of laneway support spacing on methane/air explosion shock wave

A laneway support system provides an available way to solve problems related to ground movements in underground coal mines, but also poses another potential hazard. Once a methane/air explosion occurs in a laneway, inappropriate design parameters of the support system, especially the support spacing, likely have a negative influence on explosion disaster effects. The commercial software package AutoReaGas, a computational fluid dynamics code suitable for gas explosions, was used to carry out the numerical investigation for the methane/air explosion and blast process in a straight laneway with different support spacing. The validity of the numerical method was verified by the methane/air explosion experiment in a steel tube. Laneway supports can promote the development of turbulence and explosion, and also inhibit the propagation of flame and shock wave. For the design parameters in actual laneway projects, the fluid dynamic drag due to the laneway support plays a predominant role in a methane/air explosion. There is an uneven distribution of the peak overpressure on the same cross section in the laneway, and the largest overpressure is near the laneway walls. Different support spacing can cause obvious differences for the distributions of the shock wave overpressure and impulse. Under comparable conditions, the greater destructive effects of explosion shock wave are seen for the laneway support system with larger spacing. The results presented in this work provide a theoretical basis for the optimized design of the support system in coal laneways and the related safety assessments.     

Effects of vent layout and vent area on dynamic characteristics of premixed methane-air explosion in a tube with two side-vented ducts

To further elucidate the influence mechanism of side vents on the dynamic characteristics of gas explosions in tubes is helpful to design more reasonable vent layouts. In this paper, 9.5% methane-air explosion experiments were conducted in a tube with two side-vented ducts, and the effects of vent layouts and vent areas on the dynamic characteristics of explosion overpressure and flame propagation speed were investigated. The results demonstrate that under the same condition with a single vent area of 100 mm × 100 mm, when only the end vent is open, the maximum explosion overpressure and the maximum flame propagation speed are the highest among the five vent layouts. When the side vents 1 and 2 and the end vent are open, the maximum explosion overpressure is the lowest, and an unusual discovery is that the flame front changes into a hemispherical shape, finger shape, quasi-plane shape, tulip shape and wrinkled structure. When only side vent 1 is open, a unique Helmholtz oscillation occurs, and a new discovery is that there is a consistent oscillation relationship among the overpressure, flame propagation speed and flame structure. Helmholtz oscillation occurs only when a single vent area is 100 mm × 100 mm–60 mm × 60 mm, and the oscillation degree decreases with decreasing vent area. During the vent failure stage, the maximum explosion overpressure is generated, the flame front begins to appear irregular shape, and the flame propagation speed shows a prominent characteristic peak. After the vent failure stage, the driving effect of the end vent on the flame is higher than that of the side vent on the flame. Furthermore, the correlation equations of the mathematical relationships among the maximum explosion overpressure P_red, the static activation pressure P_stat and the vent coefficient K_v under four vent layouts are established, respectively.     

瓦斯爆炸在角联通风管网中的传播特性研究*

为研究真实通风工况下瓦斯爆炸冲击波在复杂管网内的超压演化规律及高温传播规律,采用数值模拟方法,研究角联通风管网模型中各个监测点在不同通风条件下对瓦斯爆炸冲击波超压及高温的影响规律,研究结果表明:瓦斯爆炸冲击波在角联管网传播过程中产生3个局部高压区域,高温气体主要在左、右通路内传播,斜角联分支内只受到微弱影响;管网入口风流的存在,使得爆炸初期冲击波超压经相同距离传播用时更短,峰值更大,破坏力更强;风流的存在使得管网内高温气体传播状态发生改变,斜角联分支与左通路尾部热量发生积聚,温度峰值更大。     

Methane/coal dust/air explosions and their suppression by solid particle suppressing agents in a large-scale experimental tube

Methane/coal dust/air explosions under strong ignition conditions have been studied in a 199 mm inner diameter and 30.8 m long horizontal tube. A fuel gas/air manifold assembly was used to introduce methane and air into the experimental tube, and an array of 44 equally spaced dust dispersion units was used to disperse coal dust particles into the tube. The methane/coal dust/air mixture was ignited by a 7 m long epoxypropane mist cloud explosion. A deflagration-to-detonation transition (DDT) was observed, and a self-sustained detonation wave characterized by the existence of a transverse wave was propagated in the methane/coal dust/air mixtures.The suppressing effects on methane/coal dust/air mixture explosions of three solid particle suppressing agents have been studied. Coal dust and the suppressing agent were injected into the experimental tube by the dust dispersion units. The length of the suppression was 14 m. The suppression agents examined in this study comprised ABC powder, SiO₂ powder, and rock dust powder (CaCO₃). Methane/coal dust/air explosions can be efficiently suppressed by the suppression agents characterized by the rapid decrease in overpressure and propagating velocity of the explosion waves.     

巷道中瓦斯爆炸诱导激波传播特性研究

利用AutoReaGas软件,数值模拟巷道中瓦斯浓度和火源对瓦斯爆炸传播的影响,其计算结果表明:爆炸静态超压随着传播距离的增加而减小,而爆炸动压随着传播距离的增加而增大;点火位置距离巷道封闭端越近,各测点得到的爆炸静态超压值越大;瓦斯浓度对爆炸峰值超压影响显著,当浓度为9.5%的氧化反应当量比浓度时,得到的最大峰值超压为70.95kPa,爆炸威力最大。     

长管中立体障碍物对瓦斯爆炸特性影响的研究

管道内可燃气体火焰传播与障碍物相互作用的过程的研究对爆炸场所预估和防爆工程设计具有重要的意义,在实际生产、生活中,火焰传播方向上的障碍物往往具有立体结构,基本没有平面结构,因此,利用长管密闭容器,在立体障碍物存在的条件下,研究了瓦斯爆炸压力和火焰传播速度。研究结果表明:随着障碍物数量的增加,瓦斯爆炸压力和火焰传播速度随之增大;阻塞率增加,瓦斯爆炸压力和火焰传播速度出现先增大后减小的现象,当阻塞率为50%时,其爆炸压力和火焰传播速度达到最大;障碍物的摆放形式对瓦斯爆炸压力和火焰传播速度也有一定的影响。     

Enhancement effects of methane/air explosion caused by water spraying in a sealed vessel

Experiments about the influence of ultrafine water mist on the methane/air explosion were carried out in a fully sealed visual vessel with methane concentrations of 8%, 9.5%, 11% and 12.5%. Water mists were generated by two nozzles and the droplets' Sauter Mean Diameters (SMD) were 28.2 μm and 43.3 μm respectively which were measured by Phase Doppler Particle Anemometer (PDPA). A high speed camera was used to record the flame propagation processes. The results show that the maximum explosion overpressure, pressure rising rate and flame propagation velocity of methane explosions in various concentrations increased significantly after spraying. Furthermore, the brightness of explosion flame got much higher after spraying. Besides, the mist with a larger diameter had a stronger turbulent effect and could lead to a more violent explosion reaction.