Effect of pyrolysis and oxidation characteristics on lauric acid and stearic acid dust explosion hazards

The effect of pyrolysis and oxidation characteristics on the explosion sensitivity and severity parameters, including the minimum ignition energy MIE, minimum ignition temperature MIT, minimum explosion concentration MEC, maximum explosion pressure P_max, maximum rate of pressure rise (dP/dt)_max and deflagration index K_st, of lauric acid and stearic acid dust clouds was experimentally investigated. A synchronous thermal analyser was used to test the particle thermal characteristics. The functional test apparatuses including the 1.2 L Hartmann-tube apparatus, modified Godbert-Greenwald furnace, and 20 L explosion apparatus were used to test the explosion parameters. The results indicated that the rapid and slow weight loss processes of lauric acid dust followed a one-dimensional diffusion model (D1 model) and a 1.5 order chemical reaction model (F1.5 model), respectively. In addition, the rapid and slow weight loss processes of stearic acid followed a 1.5 order chemical reaction model (F1.5 model) and a three-dimensional diffusion model (D3 model), respectively, and the corresponding average apparent activation energy E and pre-exponential factor A were larger than those of lauric acid. The stearic acid dust explosion had higher values of MIE and MIT, which were mainly dependent on the higher pyrolysis and oxidation temperatures and the larger apparent activation energy E determining the slower rate of chemical bond breakage during pyrolysis and oxidation. In contrast, the lauric acid dust explosion had a higher MEC related to a smaller pre-exponential factor A with a lower amount of released reaction heat and a lower heat release rate during pyrolysis and oxidation. Additionally, due to the competition regime of the higher oxidation reaction heat release and greater consumption of oxygen during explosion, the explosion pressure P_m of the stearic acid dust was larger in low concentration ranges and decayed to an even smaller pressure than with lauric acid when the concentration exceeded 500 g/m³. The rate of explosion pressure rise (dP/dt)_m of the stearic acid dust was always larger in the experimental concentration range. The stearic acid dust explosion possessed a higher P_max, (dP/dt)_max and K_st mainly because of a larger pre-exponential factor A related to more active sites participating in the pyrolysis and oxidation reaction. Consequently, the active chemical reaction occurred more violently, and the temperature and overpressure rose faster, indicating a higher explosion hazard class for stearic acid dust.     

Risk assessment method of polyethylene dust explosion based on explosion parameters

The explosion characteristic parameters of polyethylene dust were systematically investigated. The variations in the maximum explosion pressure (P_max), explosion index (K_st), minimum ignition energy (MIE), minimum ignition temperature (MIT), and minimum explosion concentration (MEC) of dust samples with different particle sizes were obtained. Using experimental data, a two-dimensional matrix analysis method was applied to classify the dust explosion severity based on P_max and K_st. Then, a three-dimensional matrix was used to categorize the dust explosion sensitivity based on three factors: MIE, MIT, and MEC. Finally, a two-dimensional matrix model of dust explosion risk assessment was established considering the severity and sensitivity. The model was used to evaluate the explosion risk of polyethylene dust samples with different particle sizes. It was found that the risk level of dust explosion increased with decreasing particle size, which was consistent with the actual results. The risk assessment method can provide a scientific basis for dust explosion prevention in the production of polyethylene.     

Comparative study of explosion processes controlled by homogeneous and heterogeneous combustion mechanisms

The dust explosion behaviors induced by two different combustion mechanisms (homogeneous and heterogeneous mechanisms) were comparatively investigated, based on the experiments under different dust concentrations, particle sizes and initial pressures in Siwek 20-L chamber. Based on the thermo-gravimetric analysis (TGA), sweet potato dust and magnesium dust were selected as the representative dusts with homogeneous and heterogeneous combustion mechanisms, respectively. Experiments find that these two dusts have different behaviors in the explosion kinetics due to different combustion mechanisms. For sweet potato dust, the explosion pressure p_max, the pressure rise rate (dp/dt)_max and the combustion fraction η exhibit similar variation trends as dust concentration increases and they all reach to the maximum values at the worst-case concentration; while for magnesium dust, the variation of (dp/dt)_max is somewhat different from that of p_max, that is, the (dp/dt)_max will achieve the maximum at the concentration higher than the worst-case and keep stabilized with further increase of dust concentration. As the particle size decreases, the (dp/dt)_max for sweet potato dust will increasingly rise and gradually approach to a stabilized value, but for magnesium dust, the increase of (dp/dt)_max becomes pronounced only in the range of smaller particle sizes. To account the effect of initial pressure on p_max under different combustion mechanisms, a dimensionless pressure P_R was introduced to denote the relative intensity of explosion. It is found that, for sweet potato dust, the increased initial pressure will promote the explosion process (or with high P_R) for the dust cloud with high concentration due to the augmented oxygen concentration, but for the dust cloud with low concentration, the increased initial pressure will suppress the explosion process due to the increased resistance in devolatilization. For magnesium dust, the rise of initial pressure will generally promote the explosion process even for the dust cloud with low concentration; however, in the case of small particle size, the promotion of increased initial pressure to the explosion process is not so pronounced.     

Niacin,lycopodium and polyethylene powder explosibility in 20-L and 1-m3 test chambers

An experimental program has been undertaken to investigate the explosibility of selected organic dusts. The work is part of a larger research project aimed at examination of a category of combustible dusts known as marginally explosible. These are materials that appear to explode in laboratory-scale test chambers, but which may not produce appreciable overpressures and rates of pressure rise in intermediate-scale chambers. Recent work by other researchers has also demonstrated that for some materials, the reverse occurs – i.e., values of explosion parameters are higher in a 1-m³ chamber than one with a volume of 20 L. Uncertainties can therefore arise in the design of dust explosion risk reduction measures.The following materials were tested in the current work: niacin, lycopodium and polyethylene, all of which are well-known to be combustible and which cover a relatively wide range of explosion consequence severity. The concept of marginal explosibility was incorporated by testing both fine and coarse fractions of polyethylene. Experiments were conducted at Dalhousie University using the following equipment: (i) Siwek 20-L explosion chamber for determination of maximum explosion pressure (P_max), volume-normalized maximum rate of pressure rise (K_St), and minimum explosible concentration (MEC), (ii) MIKE 3 apparatus for determination of minimum ignition energy (MIE), and (iii) BAM oven for determination of minimum ignition temperature (MIT). Testing was also conducted at Fauske & Associates, LLC using a 1-m³ explosion chamber for determination of P_max, K_St and MEC. All equipment were calibrated against reference dusts, and relevant ASTM methodologies were followed in all tests.The explosion data followed known trends in accordance with relevant physical and chemical phenomena. For example, P_max and K_St values for the fine sample of polyethylene were higher than those for the coarse sample because of the decrease in particle size. MEC values for all samples were comparable in both the 20-L and 1-m³ chambers. P_max and K_St values compared favorably in the different size vessels except for the coarse polyethylene sample. In this case, K_St determined in a volume of 1 m³ was significantly higher than the value from 20-L testing. The fact that the 20-L K_St was low (23 bar m/s) does not indicate marginal explosibility of the coarse polyethylene. This sample is clearly explosible as evidenced by the measured values of MEC, MIE, MIT, and 1-m³ K_St (at both 550 and 600 ms ignition delay times).     

Effects of a carbon monoxide-dominant gas mixture on the explosion and flame propagation behaviors of methane in air

This work aimed to experimentally evaluate the effects of a carbon monoxide-dominant gas mixture on the explosion characteristics of methane in air and report the results of an experimental study on explosion pressure measurement in closed vessel deflagration for a carbon monoxide-dominant gas mixture over its entire flammable range. Experiments were performed in a 20-L spherical explosion tank with a quartz glass window 110 mm in diameter using an electric spark (1 J) as the ignition source. All experiments were conducted at room temperature and at ambient pressure, with a relative humidity ranging from 52 to 73%. The peak explosion pressure (P_max), maximum pressure rise rate ((dp/dt)_max), and gas deflagration index (K_G) were observed and analyzed. The flame propagation behavior in the initial stage was recorded using a high-speed camera. The spherical outward flame front was determined on the basis of a canny method, from which the maximum flame propagation speed (S_n) was calculated. The results indicated that the existence of the mixture had a significant effect on the flame propagation of CH₄-air and increased its explosion risk. As the volume fraction of the mixed gas increases, the P_max, (dp/dt)_max, K_G and S_n of the fuel-lean CH₄-air mixture (7% CH₄-air mixture) increase nonlinearly. In contrast, addition of the mixed gas negatively affected the fuel-rich mixture (11% CH₄-air mixture), exhibiting a decreasing trend. Under stoichiometric conditions (9.5% CH₄-air mixture), the mixed gas slightly lowered P_max, (dp/dt)_max, K_G, and S_n. The P_max of CH₄-air mixtures at volume fractions of 7%, 9.5%, and 11% were 5.4, 6.9, and 6.8 bar, respectively. The S_n of CH₄-air mixtures at volume fractions of 7%, 9.5%, and 11% were 1.2 m/s, 2.0 m/s, and 1.8 m/s, respectively. The outcome of the study is comprehensive data that quantify the dependency of explosion severity parameters on the gas concentration. In the storage and transportation of flammable gases, the information is required to quantify the potential severity of an explosion, design vessels able to withstand an explosion and design explosion safety measures for installations handling this gas.     

Validation of a new formula for predicting the lower flammability limit of hybrid mixtures

A correlation of the lower flammability limit for hybrid mixtures was recently proposed by us. The experimental conditions including ignition energy and turbulence which play a primary role in a gas or dust explosion were at fixed values. The sensitivity of such experimental conditions to the accuracy of the proposed formula was not thoroughly discussed in the previous work. Therefore, this work studied the effect of varying the ignition energy and turbulence intensity to the formula proposed in our previous paper. For ignition energy effect, results from methane/niacin mixture demonstrated that the MEC and LFL will not be affected by changing ignition energy. There is no distinguishable difference among gas explosion index (K_G) and dust explosion index (K_St) derived from tests with every ignition energy (2.5 kJ, 5 kJ and 10 kJ) in a 36 L vessel. The proposed formula is independent of ignition energy. For turbulence effect, the proposed formula can have a good prediction of the explosion and non-explosion zone if the ignition delay time is within a certain range. The formula prediction is good as the ignition delay time increases up to 100 ms in this work. Propane/niacin and propane/cornstarch mixtures are also tested to validate the proposed formula. It has been confirmed that the proposed formula predicts the explosion and non-explosion zone boundary of such mixtures.     

Study of the influence of melamine polyphosphate and aluminum hydroxide on the flame propagation and explosion overpressure of aluminum magnesium alloy dust

When aluminum magnesium alloy dust floats in the air, a certain ignition energy can easily cause an accidental explosion. To prevent and control the occurrence of accidental explosions and reduce the severity of accidents, it is necessary to carry out research on the explosion suppression of aluminum magnesium alloy dust. This paper uses a vertical glass tube experimental device and a 20 L spherical explosive experimental device to carry out experimental studies on the suppression of the flame propagation and explosion overpressure of aluminum magnesium alloy dust with melamine polyphosphate (MPP) and Al(OH)₃. With increasing MPP and Al(OH)₃ concentrations, the flame brightness darkened, the flame velocity and propagation distance gradually decreased, and P_max and (dp/dt)_max decreased significantly. When the amount of MPP added reached 60%, the flame propagation distance decreased to 188 mm, which is a decrease of 68%, and the explosion overpressure decreased to 0.014 MPa, effectively suppressing the explosion of aluminum magnesium alloy dust. The experimental results showed that MPP was more effective than Al(OH)₃ in inhibiting the flame propagation and explosion overpressure of the aluminum magnesium alloy dust. Finally, the inhibitory mechanisms of the MPP and Al(OH)₃ were further investigated. The MPP and Al(OH)₃ endothermic decomposition produced an inert gas, diluted the oxygen concentration and trapped active radicals to terminate the combustion chain reaction.     

Inhibiting effects by Fe2O3 on combustion and explosion characteristics of ABS resin

The global increase in the use of, and reliance on, plastics has prompted the demand for acrylonitrile-butadiene-styrene (ABS) resin in various fields. With this increased requirement, numerous failures have occurred in the ABS process. Those incidents, resulting from electrostatic discharge, powder accumulation, heat accumulation, construction sparks, and plant fires, have caused dust fire and explosions.In this study, the ABS resin was gleaned from the site and tested for its explosion parameters, including minimum ignition temperature of dust cloud (MIT_C), minimum ignition energy (MIE), and minimum explosion concentration (MEC). To improve loss prevention in the manufacturing process, ferric oxide (Fe₂O₃) as an inert additive was added in the ABS powder. According to the MIE test, Fe₂O₃ has an apparent inhibiting effect on dust explosion for the ABS dust. With the proportion of Fe₂O₃ increased from 25 to 50 mass% in ABS, the MIE increased from 67 to 540 mJ. The explosion tests via 20-L apparatus indicated that Fe₂O₃ mixed with ABS could not increase the MEC significantly. However, the explosion pressure dropped by increasing in the ratio of Fe₂O₃ in ABS. This inerting strategy of ABS was deemed to substantially lessen the probability and severity of fire and explosion.     

Combustion characteristics of pure aluminum and aluminum alloys powders

In this work, the explosion and combustion characteristics of aluminum and some aluminum alloys AlSi7Mg0.6, AlSi10Mg, AlMg5 under powders conditioning were studied. The idea was to compare the combustion of pure aluminum and aluminum alloys. The Minimum Ignition Energy (MIE) and explosion severity ΔP_max and (dP/dt)_max which represents the dust explosion parameters were measured for all powders using Hartman tube and 20 L spherical bomb. The particles temperature and flame temperature were determined by using IR pyrometer and spectroscopy respectively. The results showed that pure aluminum was more sensitive and severe than its alloys. MIE were: 4 mJ for pure aluminum, 13–23 mJ for aluminum alloys. For severity parameters, the overpressure ΔP_max were around 7–8 bars with maximum rate of pressure rise at 1170 bar/s for aluminum and 5–7 bars with 250–360 bar/s for alloys. However, it has been observed that flame temperatures were similar for aluminum and alloys and vary around 2800–3300 K as a function of concentration.     

Prediction of distance to maximum intensity of turbulence generated by grid plate obstacles in explosion-induced flows

The interaction of unburnt gas flow induced in an explosion with an obstacle results in the production of turbulence downstream of the obstacle and the acceleration of the flame when it reaches this turbulence. Currently, there are inadequate experimental measurements of these turbulent flows in gas explosions due to transient nature of explosion flows and the connected harsh conditions. Hence, majority of measurements of turbulent properties downstream of obstacles are done using steady-state flows rather than transient flows. Consequently, an empirical based correlation to predict distance to maximum intensity of turbulence downstream of an obstacle in an explosion-induced flow using the available steady state experiments was developed in this study. The correlation would serve as a prerequisite for determining an optimum spacing between obstacles thereby determining worst case gas explosions overpressure and flame speeds. Using a limited experimental work on systematic study of obstacle spacing, the correlation was validated against 13 different test conditions. A ratio of the optimum spacing from the experiment, x_exp to the predicted optimum spacing, x_pred for all the tests was between 2-4. This shows that a factor of three higher than the x_pred would be required to produce optimum obstacle spacing that will lead to maximum explosion severity. In planning the layout of new installations, it is appropriate to identify the relevant worst case obstacle separation in order to avoid it. In assessing the risk to existing installations and taking appropriate mitigation measures it is important to evaluate such risk on the basis of a clear understanding of the effects of separation distance and congestion. It is therefore suggested that the various new correlations obtained from this work be subjected to further rigorous validation from relevant experimental data prior to been applied as design tools.     

Observations of microscopic characteristics of post-explosion coal dust samples

To reveal the microscopic characteristics of the post-explosion coal dust samples, coal dust explosion tests were performed in a 20 L spherical vessel. The explosion characteristic parameters, such as the maximum pressure (P_max), the maximum rate of pressure rise ((dP/dt)_max), ignition time (t) and the deflagration index (K_St) were recorded. Meanwhile, the post-explosion dust samples were collected and analyzed. The research efforts include particle size distribution analysis, SEM analysis and FTIR analysis of dust samples before and after the explosion. The particle size range of post-explosion dust samples became wider according to the mass percent analysis. The microscopic appearance of samples in same particle size range showed some similarity. The porous structure of dust samples was observed by improving the SEM magnification. The chemical structure of dust samples before and after explosion was analyzed by FTIR.     

Thermo-kinetic modelling of dust explosions

The guidelines for protection and mitigation against hazard coming from dust explosion require the knowledge and then the evaluation either experimentally or theoretically of the thermo-kinetic parameters (i.e. K_St, P_max). We developed a numerical tool for the evaluation of the thermo-kinetic parameters of dust explosion. This model is based on the simulations of the combustion reaction by means of a detailed reaction mechanism assuming that the pyrolysis/devolatilization step is very fast and then gas combustion is controlling dust explosion. The model allows then the determination of the most conservative values of K_St, S_l, P_max. In the present paper we calculated the deflagration index and the laminar burning velocity for dusts utilized in various process industries (i.e. cornstarch, polyethylene, cellulose) as function of dust concentration. The obtained data were successfully compared with the available experimental results.     

Minimum ignition temperatures and explosion characteristics of micron-sized aluminium powder

To forestall, control, and mitigate the detrimental effects of aluminium dust, a 20-L near-spherical dust explosion experimental system and an HY16429 type dust-cloud ignition temperature test device were employed to explore the explosion characteristics of micron-sized aluminium powder under different ignition energies, dust particle sizes, and dust cloud concentration (C_dust) values; the minimum ignition temperature (MIT) values of aluminium powder under different dust particle sizes and C_dust were also examined. Flame images at different times were photographed by a high-speed camera. Results revealed that under similar dust-cloud concentrations and with dust particle size increasing from 42.89 to 141.70 μm, the MIT of aluminium powder increased. Under various C_dust values, the MIT of aluminium dust clouds attained peak value when concentrations enhanced. Furthermore, the increase of ignition energy contributed to the increase of the explosion pressure (P_ex) and the rate of explosion pressure rise [(dP/dt)_ex]. When dust particle size was augmented gradually, the P_ex and (dP/dt)_ex attenuated. Decreasing particle size lowered both the most violent explosion concentration and explosive limits.     

Fast and tiny: A model for the flame propagation of nanopowders

To avoid the influence of external parameters, such as the vessel volume or the initial turbulence, the explosion severity should be determined from intrinsic properties of the fuel-air mixture. Therefore, the flame propagation of gaseous mixtures is often studied in order to estimate their laminar burning velocity, which is both independent of external factors and a useful input for CFD simulation. Experimentally, this parameter is difficult to evaluate when it comes to dust explosion, due to the inherent turbulence during the dispersion of the cloud. However, the low inertia of nanoparticles allows performing tests at very low turbulence without sedimentation. Knowledge on flame propagation concerning nanoparticles may then be modelled and, under certain conditions, extrapolated to microparticles, for which an experimental measurement is a delicate task. This work focuses on a nanocellulose with primary fiber dimensions of 3 nm width and 70 nm length. A one-dimensional model was developed to estimate the flame velocity of a nanocellulose explosion, based on an existing model already validated for hybrid mixtures of gas and carbonaceous nanopowders similar to soot. Assuming the fast devolatilization of organic nanopowders, the chemical reactions considered are limited to the combustion of the pyrolysis gases. The finite volume method was used to solve the mass and energy balances equations and mass reactions rates constituting the numerical system. Finally, the radiative heat transfer was also considered, highlighting the influence of the total surface area of the particles on the thermal radiation. Flame velocities of nanocellulose from 17.5 to 20.8 cm/s were obtained numerically depending on the radiative heat transfer, which proves a good agreement with the values around 21 cm/s measured experimentally by flame visualization and allows the validation of the model for nanoparticles.     

Investigations into the influence of dustiness on dust explosions

A new safety characteristic the “dustiness” according to VDI 2263 – part 9 (Verein Deutscher Ingenieure, 2008) is investigated. Dustiness means the tendency of a dust to form clouds. The paper deals with the influence of the dustiness on vented dust explosions. In order to look into the effects of the dustiness on dust cloud formation and explosion properties experiments and simulations in a vertical dust dispersion glass tube apparatus were carried out.Preliminary explosion experiments showed that the dustiness has an influence on the reduced explosion pressure in a vented 75 L test apparatus. Dusts with comparable p_max and K_St values and different dustiness were tested. Dusts with higher dustiness produced higher overpressures, despite comparable safety characteristics. In order to verify the results for applications in the process industries further tests with different settings are planned as well as industrial scale experiments. Characteristics of the dust such as particle size, density, specific surface area and particle shape, which influence the dispersibility, have been determined experimentally.The Euler/Lagrange and the Euler/Euler approaches are compared for simulating an exemplary dust/air mixture. Especially sedimentation and the ability of the approaches to simulate the tendency of dust to stay airborne were investigated. The Euler/Lagrange approach is better suited for simulating local dust concentrations, particle size distributions and particle forces. It could be used to point out regions of high dust concentrations in a vessel. With the Euler/Euler method it is possible to achieve fast solutions for one specified diameter, but the simulated dust/air mixtures are always more homogenous than in reality. ANSYS CFX version 13 was used in all simulations.     

Experiment-based investigations of magnesium dust explosion characteristics

An experimental investigation was carried out on magnesium dust explosions. Tests of explosion severity, flammability limit and solid inerting were conducted thanks to the Siwek 20 L vessel and influences of dust concentration, particle size, ignition energy, initial pressure and added inertant were taken into account. That magnesium dust is more of an explosion hazard than coal dust is confirmed and quantified by contrastive investigation. The Chinese procedure GB/T 16425 is overly conservative for LEL determination while EN 14034-3 yields realistic LEL data. It is also suggested that 2000-5000 J is the most appropriate ignition energy to use in the LEL determination of magnesium dusts, using the 20 L vessel. It is essential to point out that the overdriving phenomenon usually occurs for carbonaceous and less volatile metal materials is not notable for magnesium dusts. Trends of faster burning velocity and more efficient and adiabatic flame propagation are associated with fuel-rich dust clouds, smaller particles and hyperbaric conditions. Moreover, Inerting effectiveness of CaCO₃ appears to be higher than KCl values on thermodynamics, whereas KCl represents higher effectiveness upon kinetics. Finer inertant shows better inerting effectiveness.     

Coupling effects of venting and inerting on explosions in interconnected vessels

The coupling effects of venting and CO₂ inerting on stoichiometric methane-air mixture explosions were investigated in an isolated vessel and interconnected vessels. The results indicate that venting mitigates the explosion intensity, especially for small vessels. For vessels connected by pipes, a venting design following EN 14994 (2007) and NFPA 68 (2013) could not meet the venting requirements. For an isolated big vessel and interconnected vessels, increasing the CO₂ volume fraction (Φ) from 0 to 15.0 vol% decreased the maximum explosion overpressure (P_max) and maximum rate of overpressure rise ((dP/dt)_max) and delayed t_max. For closed interconnected vessels, P_max varied approximately linearly with Φ. For both isolated vessel and interconnected vessels, the coupling effects of venting and CO₂ inerting on methane-air explosion were more efficient than those of individual mitigative method (that is, venting alone or CO₂ inerting alone).     

Experimental study on the minimum explosion concentration of anthracite dust: The roles of O2 mole fraction,inert gas and CH4 addition

The explosion characteristics of anthracite coal dust with/without small amount of CH₄ (1.14 vol %) were investigated by using a 20 L spherical explosion apparatus with an emphasis on the roles of oxygen mole fraction and inert gas. Two methods based on overpressure and combustion duration time were used to determine the minimum explosion concentration (MEC) or the lower explosion limit (LEL) of the pure anthracite coal dust and the hybrid coal-methane mixtures, respectively. The experiment results showed that increasing oxygen mole fraction increases the explosion risk of coal dust: with increasing oxygen mole fraction, the explosion pressure (P_ex) and the rate of explosion pressure rise ((dp/dt)_ex)) increase, while MEC decreases. The explosion risk of anthracite dust was found to be lower after replacing N₂ with CO₂, suggesting that CO₂ has a better inhibition effect on explosion mainly due to its higher specific heat. However, the addition of 1.14% CH₄ moderates the inhibition effect of CO₂ and the promotion effect of O₂ on anthracite dust explosion for some extent, increasing explosion severity and reducing the MEC of anthracite dust. For hybrid anthracite/CH₄ mixture explosions, Barknecht's curve was found to be more accurate and conservative than Chatelier's line, but neither are sufficient from the safety considerations. The experimental results provide a certain help for the explosion prevention and suppression in carbonaceous dust industries.     

玉米淀粉粉尘爆炸危险性研究

为研究玉米淀粉粉尘爆炸危险性,采用哈特曼管式爆炸测试装置和20 L球爆炸测试装置对200目(<75μm)以下的玉米淀粉粉尘爆炸危险性进行评估,基于静电火花和粉尘质量浓度对粉尘爆炸的影响,对玉米淀粉的静电火花最小点火能量、爆炸下限质量浓度、最大爆炸压力和爆炸指数进行了研究,根据试验结果对玉米淀粉爆炸危险性进行分级。试验结果表明:温度在25℃,喷粉压力为0.80 MPa,粉尘质量浓度在250～750 g/m3范围内,粉尘的最小点火能量随着粉尘质量浓度增加而降低,其最小点火能量在40～80 mJ之间;在点火能量为10 kJ时,粉尘爆炸下限质量浓度在50～60 g/m3之间;在粉尘质量浓度为750 g/m3时,爆炸压力达到最大,为0.66 MPa;在粉尘质量浓度为500 g/m3时,爆炸指数达到最大,为17.21 MPa.m/s,其粉尘爆炸危险性分级为Ⅰ级。     

Influence of different ignition delay times on the pressure rise rate in hybrid mixture explosions in the 20-L sphere

For the development of a standardized method for measuring the explosion safety characteristics of combustible hybrid dust/vapor mixtures, the influence of the ignition delay time needs to be investigated. The ignition delay time, defined as the time between the injection of dust and the activation of the ignition source, is related to the turbulence of the mixture and thus to the pressure rise rate. The ignition source for pure vapors, however, has to be activated in a quiescent atmosphere according to the standards. Nevertheless, when measuring the explosion safety characteristics of hybrid mixtures, it is important that the dust be in suspension around the igniter. Like pure dust/air mixtures, hybrid dust/vapor/air mixtures need to be ignited in a turbulent atmosphere to keep the dust in suspension.This work will therefore investigate the influence of ignition delay times on the severity of hybrid explosions. It was generally found that at shorter ignition delay times, (dp/dt)_ex increased due to higher turbulence and decreases as the dust sinks to the bottom of the 20 L-sphere. This effect is more pronounced for hybrid mixtures with higher vapor content compared to dust content.