Performance of the supported copper oxide catalysts for the catalytic incineration of aromatic hydrocarbons

A fixed bed reactor was used to assess the catalytic incineration of toluene by various transition-metal oxide species supported on gamma-Al(2)O(3). CuO/gamma-Al(2)O(3) was found to be the most active of seven catalysts investigated. The CuO species, with a Cu content of 5% (wt), was hence used with four different supports (CeO(2), gamma-Al(2)O(3), TiO(2) and V(2)O(5)) in order to define the optimal combination. Results of the catalytic incineration of toluene, X-ray diffraction (XRD) analysis, oxygen-temperature programmed desorption (O(2)-TPD), toluene-temperature programmed desorption (toluene-TPD) and hydrogen-temperature programmed reduction (H(2)-TPR) showed that CuO/CeO(2) was the most active catalyst, followed by CuO/gamma-Al(2)O(3). The activity of CuO/CeO(2) with respect to the VOC molecule was observed to follow this sequence: toluen>p-xylene>benzene. The addition of water vapor or CO(2) significantly inhibited the activity of the CuO/CeO(2) and CuO/gamma-Al(2)O(3) catalysts. The inhibiting effect of both was reversible for CuO/gamma-Al(2)O(3). For CuO/CeO(2), the inhibiting effect of CO(2) was reversible and even insignificant at a higher temperature (220 degrees C), but the effect of H(2)O vapor was somewhat irreversible at lower incineration temperatures (220 degrees C). For complete oxidation of toluene, the required reaction temperature increased with gas hourly space velocity (GHSV) and toluene inlet concentration.     

The catalytic incineration of styrene over an Mn2O3/Fe2O3 catalyst

In this study, styrene monomer (SM) was treated by a commercial catalyst, Mn2O3/Fe2O3, in a fixed-bed reactor. The study can be classified into two major parts. First, the effects of operating factors, such as temperature, SM concentration, space velocity, and O2 concentration, on the performance of the catalyst were investigated. Second, two catalyst life tests were carried out to characterize the deactivation effect of SM. The results show that the catalyst results in higher conversion of SM at a higher inlet temperature and higher O2 concentrations. The conversion of SM decreases with increasing SM concentration and space velocity. From the statistical analysis of the data, we find that temperature is the most important factor on the catalytic incineration. Oxygen concentration, SM concentration, and space velocity are significant parameters as well. This paper also provides information on the deactivation effect of SM. The catalysts were characterized by surface and pore-size analysis, X-ray diffraction (XRD), scanning electron microscopy (SEM), and electron spectroscopy for chemical analysis (ESCA) before and after the tests. The results show that the catalytic deactivation may be caused by carbon coating, and the pore size and surface area of the catalyst are smaller after deactivation.     

铁氧化物复合氧化铝催化臭氧化过程中溴酸盐的生成控制

以市售活性炭、硅藻土和氧化铝小球为载体,考察了负载铁基活性组分对催化臭氧化过程中溴酸盐的控制情况,其中,铁基复合氧化铝小球体现出更好的溴酸盐还原特性和催化剂稳定性,证实催化剂中铁氧化物是溴酸盐得到有效控制的主要活性组分。进一步考察了铁基复合氧化铝小球催化臭氧化处理实际原水过程中对溴酸盐的生成控制,以及反应过程中溶解性有机碳（DOC）的去除情况。结果表明,与单独臭氧化相比,该催化剂既能有效去除水中的溶解性有机物,又能明显抑制溴酸盐的生成,反应50h,其活性并没有明显下降。催化剂失活主要归因于吸附位点数量的下降,可以通过负载铁氧化物来实现催化剂的再生。     

活性组分稀土氧化物对甲苯催化燃烧性能的影响

以活性组分氧化铜、氧化锰为基础,加入活性组分稀土氧化物,研究对甲苯催化燃烧性能影响。研究结果表明,在所选稀土氧化物中,加入氧化铈时甲苯的起燃温度和完全燃烧温度最低;在一定的负载量下,Cu：Mn：Ce摩尔比为1：2：0.7时,制备的CuMnCe/ZrO2整体催化剂甲苯完全燃烧温度最低;催化剂合理的焙烧温度为500℃,此时甲苯的起燃温度约200℃,完全燃烧温度为220℃;催化剂合理的焙烧时间为3 h。     

Catalytic reduction of N2O over Ag-Pd/Al2O3 bimetallic catalysts

A study of the catalytic conversion of N2O to N2 over a bimetallic Ag-Pd catalyst is described in this article. Several Ag-Pd catalytic systems were prepared supported on Al2O3 with different ratios and their catalytic activity for the direct decomposition of N2O and their reduction with CO was measured. Based on the experimental results, it was observed that Ag-Pd bimetallic catalyst (5-0.5%) was the most active for both nitrous oxide reduction and direct decomposition. This high activity seems to be connected with a synergistic effect between Ag and Pd.     

Mn的氧化价态对Mn／γ-Al2O3催化剂催化臭氧氧化气相低浓度甲苯的影响

采用共沉淀法,以Al2O3为载体制备Mn／γ-Al2O3和Mn—Ce／Mn／γ-Al2O3催化剂,并分别在N2气氛和O2气氛下焙烧。采用固定床连续流动反应器,研究所制备催化剂在室温条件下催化臭氧氧化甲苯的性能。通过XRD、XPS和FTIR等手段对催化剂的结构和组成进行表征。结果表明,Mn／Mn／γ-Al2O3催化剂具有良好的催化臭氧氧化甲苯和催化臭氧自身分解的性能,共沉淀法制备催化剂的最佳Mn负载量为20％。O2气氛焙烧和Ce的加入,可以有效提高催化剂的活性和寿命。原因是O2气氛焙烧和Ce的加入可以提高Mn的氧化价态。催化剂失活的主要原因是有机副产物在催化剂表面吸附堆积,失活催化剂在550℃、空气气氛下焙烧可恢复催化性能。     

Mo掺入CeO2/Al2O3选择性催化还原NO动力学研究

采用共混法制备不同系列Mo掺入催化剂（CeMoxOy/Al2O3）,研究了Mo掺入对CeO2/Al2O3选择性催化还原NO活性的优化,考察了内外扩散对脱硝性能的影响,并计算得出反应活化能,从动力学角度考察了Mo掺入对脱硝活性反应速率的影响。结果表明,Al/Ce/Mo元素摩尔比为5：1：0.15,空速为7 200 h-1,煅烧温度为550 ℃时,催化剂在250~425 ℃内脱出NOx效率均大于90%;催化剂平均粒径小于40目时,空速大于105 h-1时,内外扩散的影响可以忽略不计, CeMoxOy/Al2O3催化反应为一级反应,其中NH3和O2反应级数近似为0级。 CeMo0.15Oy/Al2O3活化能为36.57 kJ·mol-1,Mo的添加有效的减小了催化剂的表观反应活化能,增加了反应速率,提高了催化活性。     

Cr-Ce/Al2O3催化剂对挥发性有机物的催化降解

采用共沉淀法制备了一系列不同铬铈负载量和铬铈负载比例的Cr-Ce/Al2O3催化剂,采用XRD、BET、NH3-TPD以及H2-TPR对所制得的催化剂进行表征。在空速为15 000 h-1、挥发性有机物体积分数为1 500 μL·L-1的条件下,于固定床反应器上考察了催化剂在三氯乙烯(TCE)催化氧化降解反应中的催化活性。实验结果表明,Cr-Ce/Al2O3(5%,10%)系列催化剂具有较好的低温催化降解三氯乙烯活性,其中Cr-Ce/Al2O3(5%,10%)活性最高,在271.3 ℃时可将尾气中90%的三氯乙烯降解。催化剂反应800 min后活性仅有轻微下降,说明该催化剂具有较好的稳定性。此外,将该催化剂用于其他VOCs催化降解反应中同样具有较好的活性,在350 ℃时可以将尾气中VOCs完全降解。     

Supported transition-metal oxide catalysts for reduction of sulfur dioxide with hydrogen to elemental sulfur

This work is for the purpose to find a high performance catalyst for the catalytic reduction of SO2 with H2 as a reducing agent. NiO/gamma-Al2O3 catalyst was found to be the most active catalyst among the seven gamma-Al2O3-supported metal-oxide catalysts tested. With NiO as the active species, of the supports tested, gamma-Al2O3 was the most suitable one and the optimal Ni content was 16 wt%. Using this NiO/gamma-Al2O3 catalyst, we found that the optimal feed ratio of H2/SO2 is 2:1 and the catalyst presulfided with H2 + H2S exhibits a higher performance than that pretreated with H2 or He. XRD patterns reveal that the nickel oxide experienced a transformation to Ni3S2 and NiS, and then to NiS2, the most active nickel sulfide, during the reaction process. The reason for the highest catalyst activity of 16 wt% Ni was attributed to the largest amount of NiS2. Water vapor in the feed gas reactant caused inhibition of catalyst activity, whereas H2S promoted the reduction of SO2. These phenomena were rationalized with the aid of Claus reaction.     

Hydrodechlorination of dichlorobiphenyls over Ni-Mo/Al2O3 catalysts prepared by spray-drying method

The hydrodechlorination (HDCl) process of 2,3-, 2,4- and 2,5-dichlorobiphenyls was studied over a sulphided Ni-Mo/Al(2)O(3) catalyst in a stirred autoclave at a hydrogen pressure of 3 MPa. The catalysts were prepared by spray-drying. They were characterized by N(2) adsorption, thermogravimetry and scanning electron microscopy with X-ray microanalysis. The reaction temperature of the catalytic HDCl process was varied in the range of 230-290 degrees C. Polychlorinated biphenyls (PCBs) free transformer oil was used as reaction medium. The HDCl degree of dichlorobiphenyl isomers was in the range of 82-93%. The efficiency in the chlorine removal was found to be related to the position of the substituted chlorine atom and decreased as follows 2,4-dichlorobiphenyl approximately 2,5-dichlorobiphenyl>2,3-dichlorobiphenyl. For comparison, the HDCl process of 2,3-dichlorobiphenyl (2,3-PCB) without catalyst was also studied. The chlorine removal was 85% for the catalytic HDCl of 2,3-PCB whereas non-catalytic process led only to 16% of dechlorination in the same operating conditions, i.e. at 290 degrees C after 120 min. Monodichlorobiphenyls were not detected in the reaction products. The data for both catalytic and non-catalytic conversion of 2,3-PCB fit to a first-order model. Kinetic constants and the activation energy of the overall HDCl reaction of 2,3-PCB to biphenyl were evaluated. Compared to non-catalytic process, a nearly threefold decrease in the activation energy was observed in the presence of Ni-Mo/Al(2)O(3) catalyst prepared by spray-drying (48 kJ mol(-1) vs. 124 kJ mol(-1)).     

新型Cu-Co-O_x催化剂的制备及其催化燃烧甲苯的性能研究

采用浸渍法制备自制载体负载复合金属氧化物Cu-Co-Ox催化剂。研究了Cu-Co-Ox催化剂催化燃烧甲苯的活性。分别考察了Cu-Co-Ox负载量、Cu/Co(摩尔比)及焙烧温度对催化燃烧甲苯活性的影响,并采用X射线衍射(XRD)及扫描电镜(SEM)等表征技术,分别对复合金属氧化物Cu-Co-Ox的晶型与结晶形貌进行了分析。结果表明,焙烧温度为600℃,Cu-Co-Ox负载量为5%(质量分数),Cu/Co为1∶2时,Cu-Co-Ox催化燃烧甲苯的活性最高。当反应温度为250℃,甲苯的转化率达到95%以上。XRD分析表明,Cu-Co-Ox催化剂主要活性相为CuCo2O4尖晶石。     

氧化物催化剂对非热等离子体催化降解甲苯的影响

考察了在干燥气氛下不同氧化物催化剂对非热等离子体催化降解甲苯的影响。从甲苯降解率、碳平衡、CO2选择性和O3去除4个方面,对比了氧化物催化剂的介电性能、表面供氧能力和比表面积与多孔结构对反应产生影响的强弱。结果表明,催化剂的介电性能有利于甲苯降解率、碳平衡和O3产量的提高,但对CO2选择性和O3去除的影响极小;一定能量密度下,催化剂比表面积与多孔结构对CO2选择性和O3去除所产生的影响要强于介电性能;催化剂表面供氧能力可明显促进反应的进行,其对反应所产生的影响要强于比表面积与多孔结构。     

钒硅催化脱硫脱硝的研究

考察了经10% H2-90% Ar(体积分数)还原的钒硅催化剂在固定床石英玻璃反应器中的脱硫脱硝活性,研究了反应温度、SO2/NO摩尔比及O2浓度对SO2和NO脱除率的影响.结果表明,还原后的钒硅催化剂的平均NO脱除率提高了15%左右;反应温度对脱硫脱硝影响较大,当温度为400℃以上时SO2和NO脱除率基本保持稳定;SO2/NO摩尔比为2和5时,钒硅催化剂的NO脱除率较高;模拟烟气中有O2条件下的脱硫脱硝活性明显高于无O2条件,O2体积分数为6.00%时SO2和NO脱除率达到最大.     

The kinetics of catalytic incineration of dimethyl sulfide and dimethyl disulfide over an MnO/Fe2O3 catalyst

The catalytic incineration of dimethyl sulfide and dimethyl disulfide [(CH3)2S and (CH3)2S2] over an MnO/Fe2O3 catalyst was carried out in a bench-scale catalytic incinerator. Three kinetic models (i.e., the power-rate law, the Mars and Van Krevelen model, and the Langmuir-Hinshelwood model) were used to analyze the results. A differential reactor design was used for best fit of kinetic models in this study. The results show that the Langmuir-Hinshelwood model may be feasible to describe the catalytic incineration of (CH3)2S and (CH3)2S2. This suggests that the chemical adsorption of O2 molecules is important in this incineration.     

前驱体对Cu/Al2O3的HCN催化水解性能的影响

为了研究前驱体因素对Cu/Al2O3的HCN催化水解性能的影响,考察了铜盐前驱体种类和前驱体溶液浓度对催化剂脱除HCN的规律变化,并探究了焙烧温度和反应温度对催化水解HCN的影响。采用浸渍法制备了Cu/Al2O3催化剂,并采用BET、SEM、XRD和XPS等对催化剂进行了表征。实验结果表明,以乙酸铜为前驱体制备的催化剂因具有较好的孔结构和较多的CuO负载量,使其相较其他3种铜盐表现出了最好的催化活性。当乙酸铜前驱体溶液浓度为0.050 mol·L-1,焙烧温度为400℃时,催化剂的催化活性最高。反应温度越高,越有利于提升催化活性。反应温度为250℃时,催化剂对HCN的脱除效率即达到96%以上。可见,以乙酸铜为前驱体制备的催化剂用于低温催化水解HCN效果理想,具有较好的应用前景。     

在Ru/Al2O3催化剂上用H2对SO2选择性催化还原的研究

本文对用H2来使SO2选择性催化还原为单质硫在Ru/Al2O3催化剂上的行为进行研究.当物料比经过优化确定为SO2/H2=12.8时,在500℃下,SO2的转化率为90%以上,单质硫的产率为70%左右.比较于其他的催化还原SO2的催化剂,本催化剂采用金属而不是金属硫化物,这样既省去了催化剂预硫化的过程,同时也使在有氧条件下的选择性催化还原成为可能.实验考察了O2及水蒸气存在对过程的影响.在实验过程中发现,H2S作为中间产物生成,可推论该过程在催化剂上分两步进行SO2首先在催化剂金属上被H2深度还原为H2S,然后在Al2O3载体的酸性中心上SO2与H2S发生Claus反应产生单质硫.     

Ozone-enhanced catalytic oxidation of monochlorobenzene over iron oxide catalysts

In this study, we examined the experimental catalytic oxidation of gaseous monochlorobenzene (MCBz) with O₃ over Fe₂O₃ in a packed bed reactor to investigate the feasibility of economical low temperature decomposition at a high space velocity (SV). We investigated the effects of several reaction parameters (temperature, O₃ concentration, and SV) on the MCBz oxidation. At 150 °C, the conversion of MCBz over Fe₂O₃ in the absence of O₃ was only 3%; it increased to 91% over Fe₂O₃ in the presence of 1200 ppm of O₃ at a high SV of 83 s⁻¹. A long-term operation study revealed that the conversion of MCBz was stable for more than 96 h. In the steady state, the carbon and chlorine balances were 88% and 86%, respectively. Applying a Langmuir-Hinshelwood kinetic model, we estimated an activation energy of 16.7 kJ mol⁻¹ for MCBz oxidation over Fe₂O₃ in the presence of O₃.     

The promoter effect and a rate expression of the catalytic incineration of (CH3)2S2 over an improved CuO-MoO3/gamma-Al2O3 catalyst

The CuO-MoO3/gamma-Al2O3 catalyst, confirmed previously as having good activity in the catalytic incineration of (CH3)2S2, was employed as the principal catalyst in this study. With the aim of improving catalyst activity and resistance to deactivation by sulfur compounds, a promoter was added either before adding the precursors of Cu and Mo or together with Cu and Mo onto the gamma-Al2O3. Promoters included transition metals and elements from groups IA-VIIA in the chemical periodic table. Experimental results reveal Cr2O3 as the most effective promoter, with an optimal composition of 5 wt.% Cu, 6 wt.% Mo and 4 wt.% Cr (designated as Cu(5)-Mo(6)-Cr(4)/gamma-Al2O3). Knowing that higher acidity can improve activity, we further investigated the effect of acid treatment on the performance of the Cu(5)-Mo(6)-Cr(4)/gamma-Al2O3 catalyst. Experimental results indicate the H2SO4-treated catalyst (Cu(5)-Mo(6)-Cr(4)/sulfated-gamma-Al2O3) has a better activity and durability. A study for finding an appropriate rate expression for the catalytic incineration of (CH3)2S2 by Cu(5)-Mo(6)-Cr(4)/sulfated-gamma-Al2O3 was carried out in a differential reactor. The results show that the Mars-Van Krevelen model is applicable to this destructive oxidation reaction. Results additionally reveal that competitive adsorption of CH4 reduces conversion of (CH3)2S2.     

Fe2O3-Cr2O3/TiO2系列催化剂的结构和脱硝性能

研究以纳米TiO2为载体,浸渍负载过渡金属氧化物,以CO为还原剂的脱硝催化剂的脱硝性能。实验中以计算量的Ni（NO3）2和Fe（NO3）3混合溶液浸渍纳米TiO2粉末,室温下搅拌30 min至混合均匀,放入旋转蒸发器中,70℃下至水分蒸干为止;所得粉末在550℃下、空气气氛中焙烧4 h即得所需催化剂。用以上方法分别制备2%Fe2O3-10%Cr2O3/TiO2、4%Fe2O3-8%Cr2O3/TiO2、6%Fe2O3-6%Cr2O3/TiO2、8%Fe2O3-4%Cr2O3/TiO2与10%Fe2O3-2%Cr2O3/TiO2等5种催化剂样品。实验结果表明,制备的催化剂具有较好的结构,分散较为均匀。对于CO＋NO反应,Fe2O3-Cr2O3/TiO2系列催化剂具有较好的催化活性,NO的转化率都达到了100%。其中,10%Fe2O3-2%Cr2O3/TiO2样品具有最好的低温活性,H2-TPR结果表明,这是由于10%Fe2O3-2%Cr2O3/TiO2催化剂更易于被CO预还原。     

The improved activity of Co3O4 nanorods using silver in the catalytic oxidation of toluene

Environmental Science and Pollution Research - Co3O4 nanorods with diameters of ~0.15 μm and lengths of ~1 μm were prepared using a hydrothermal method via the assembly of microcrystals...