超声波-光催化氧化降解邻氯苯酚的研究

对超声波-光催化氧化降解邻氯苯酚(2-cp)进行了研究,探讨了溶液初始pH值、TiO2投加量、H2O2投加量和溶液初始浓度对邻氯苯酚降解率的影响.并对几种不同处理方法降解邻氯苯酚的结果进行了对比.结果表明,超声波和紫外光的协同效果明显,在相同的反应时间内,超声波能够明显提高光催化降解邻氯苯酚的降解率.超声波和紫外光连用,具有良好的工业应用前景.     

超声波光催化协同降解对甲基苯磺酸水溶液的机理研究

采用超声波与光催化联合法对模拟废水中难生物降解的对甲基苯磺酸(4-TSA)进行降解实验研究,借助紫外光谱、红外光谱、质谱、气相色谱、高效液相色谱、化学需氧量和总有机碳的检测结果对反应机理进行了初步探讨.实验结果表明:超声波和光催化之间存在着协同效应;当溶液初始质量浓度30 mg/L,光催化剂TiO2投加量为100 mg...     

天然沸石负载La2O3-ZnO-TiO2光催化降解活性艳红K-2BP

利用80目天然斜发沸石作载体制备La2O3(0.5%)-ZnO(20%)-TiO2/沸石复合光催化剂,以20 W紫外灯为光源,在自制的光催化反应器中降解活性艳红K-2BP,考察了光照时问、空气通入量、催化剂用最、溶液初始浓度、H2O2与Fe3 投加量等对活性艳红K-2BP光催化降解率的影响.结果表明,当溶液初始浓度为60 mg/L,催化剂投加量为12 g/L,通气量为1 200 mL/min,光照2.5 h,活性艳红K-2BP的降解率可达99.2%;H2O2和Fe3投加量为4 mL/L和3 g/L时,光照1 h活性艳红K-2BP降解率分别为100%和97.2%.紫外-可见吸收光谱显示,LZTZ光催化剂町有效降解印染废水.     

超声—紫外协同催化降解废水中■的研究

选择纳米TiO_2为催化剂,研究超声—紫外协同催化降解■的效果。考察了不同TiO_2类型、TiO_2投加量、H_2O_2投加量、超声频率、超声强度、溶液初始pH和■初始浓度等因素对■降解率的影响,并对协同催化降解的机制进行了探讨。结果表明,不同类型TiO_2对■的降解效果为P25型TiO_2锐钛矿型TiO_2金红石型TiO_2。在■初始质量浓度为5 mg/L、P25型TiO_2投加量为0.06g/L、H_2O_2投加量为60mmol/L、超声频率为80kHz、超声强度为0.300W/cm~2、溶液初始pH为3.0的条件下,反应10min时超声—紫外协同催化对■的降解率最高可达98.26%。超声和紫外光对■的降解具有协同促进效应,其协同因子为2.08。机制分析表明,超声—紫外协同催化降解■的机制是以·OH为主要自由基的高级氧化作用,1,3-二苯丙烷和对苯基苯酚为主要中间产物。     

纳米二氧化钛复合石墨烯催化剂的制备及处理染料废水

以硫酸钛为原料,采用共沉淀法,制备了一系列纳米二氧化钛复合石墨烯催化剂,采用XRD和FTIR对样品进行表征。通过紫外光照射亚甲基蓝溶液光催化降解实验,研究石墨烯的加入量对TiO2光催化性能的影响,结果表明,TiO2-GO-5具有最佳的光催化性能。在pH=6.00、TiO2-GO-5的投加量为0.070 g/50 mL、光照3 h条件下,100 mg/L亚甲基蓝溶液的脱色率达到最大值为90.52%。     

镍网负载纳米TiO_2光催化反应器对酸性品红脱色效果实验研究

采用负载纳米TiO2的三维镍网装配了光催化反应器,就其对酸性品红溶液进行脱色效果进行了实验研究。考察了反应器的3种装配条件、品红初始浓度、pH值、H2O2投加量、紫外光剂量等因素对酸性品红脱色效果的影响。结果表明:UV灯+镍网+TiO2模式组合的反应器脱色效果最好;在相同的处理时间内酸性品红溶液的脱色率随起始浓度的增大而减小;将酸性品红溶液pH值调至5时脱色效果最明显,70 min的脱色率可高达94.8%。脱色效果还可以通过溶液中添加H2O2和控制紫外线剂量来调节。当溶液中H2O2投加量为0.5 g/L时,处理70 min后的脱色率可高达98.3%;到达反应界面紫外光剂量越多则能够获得越高的酸性品红脱色率。     

镍网负载纳米TiO2光催化反应器对酸性品红脱色效果实验研究

采用负载纳米TiO2的三维镍网装配了光催化反应器,就其对酸性品红溶液进行脱色效果进行了实验研究。考察了反应器的3种装配条件、品红初始浓度、pH值、H2O2投加量、紫外光剂量等因素对酸性品红脱色效果的影响。结果表明：UV灯＋镍网＋TiO2模式组合的反应器脱色效果最好;在相同的处理时间内酸性品红溶液的脱色率随起始浓度的增大而减小;将酸性品红溶液pH值调至5时脱色效果最明显,70 min的脱色率可高达94.8%。脱色效果还可以通过溶液中添加H2O2和控制紫外线剂量来调节。当溶液中H2O2投加量为0.5 g/L时,处理70 min后的脱色率可高达98.3%;到达反应界面紫外光剂量越多则能够获得越高的酸性品红脱色率。     

超声波/铁粉对废水2,4-二氯酚的降解研究

采用超声波/铁粉协同作用,降解废水中的2,4-二氯酚,考察了超声功率、铁粉投加量、2,4-二氯酚初始质量浓度、溶液初始pH值等因素,对2,4-二氯酚降解效果的影响,并对其动力学进行了初步探讨。结果表明：超声波与铁粉具有明显的协同效应。在超声波与铁粉的协同作用下,2,4-二氯酚的降解效率,随着超声功率的增大和初始质量浓度的减小而增大,随着铁粉投加量的增加而增大,但铁粉的投加量达到20 g/L时,降解效率的增幅趋于平缓。在pH值为4的弱酸性条件下,2,4-二氯酚的降解效率最佳,pH值为8时,降解效率次之,在中性或弱碱性条件下,降解效率最差。投加适量的铜作催化剂,可提高2,4-二氯酚的降解效率。本实验条件下,催化剂Cu^2＋的最佳投加量为0.256 g/L。超声波/铁粉协同作用对2,4-二氯酚的降解过程符合一级动力学反应规律。协同体系中,2,4-二氯酚降解速率比单独超声降解和铁粉单独作用时的降解速率分别提高了大约13倍和5倍。     

超声波/Fenton工艺降解微量邻苯二甲酸二甲酯和壬基酚效能的研究

研究了在超声波、Fenton不同体系中邻苯二甲酸二甲酯(DMP)和壬基酚(NP)的降解效果.通过正交实验得到超声波/Fenton工艺各个因素影响程度的大小为:H2O2投加量＞初始pH＞反应时间＞Fe2+投加量＞超声功率.最后得到降解250mL质量浓度为100 μg/L的DMP的最佳条件:H2 O2投加量为2 mmol/L、Fe2+投加量为0.40 mmol/L、初始pH为3.00、超声功率为1 800W、反应时间为120 min,降解率可达到85.96％;降解250mL质量浓度为100 μg/L的NP的最佳条件:H2O2投加量为4mmol/L、Fe2+投加量为0.50 mmol/L、初始pH为3.00、超声功率为1 800W、反应时间为120 min,降解率可达到78.70％.     

磷钨酸季铵盐-β-环糊精包合物光催化降解甲基橙

制备了磷钨酸季铵盐-β-环糊精包合物,并进行了初步表征,用正交实验优化了包合物的制备条件。在光催化反应仪中,以紫外灯为光源,以包合物为光催化剂,研究了其对模拟染料废水甲基橙溶液的光催化降解脱色的影响。讨论了影响光催化降解效果的溶液初始酸度、催化剂投加量和甲基橙的初始浓度等几个重要因素。     

Photochemical degradation and mineralization of 4-chlorophenol

INTENTION, GOAL, SCOPE, BACKGROUND: Since the intermediate products of some compounds can be more toxic and/or refractory than the original compund itself, the development of innovative oxidation technologies which are capable of transforming such compounds into harmless end products, is gaining more importance every day. Advanced oxidation processes are one of these technologies. However, it is necessary to optimize the reaction conditions for these technologies in order to be cost-effective. OBJECTIVE: The main objectives of this study were to see if complete mineralization of 4-chlorophenol with AOPs was possible using low pressure mercury vapour lamps, to make a comparison of different AOPs, to observe the effect of the existence of other ions on degradation efficiency and to optimize reaction conditions. METHODS: In this study, photochemical advanced oxidation processes (AOPs) utilizing the combinations of UV, UV/H2O2 and UV/H2O2/Fe2+ (photo-Fenton process) were investigated in labscale experiments for the degradation and mineralization of 4-chlorophenol. Evaluations were based on the reduction of 4-chlorophenol and total organic carbon. The major parameters investigated were the initial 4-chlorophenol concentration, pH, hydrogen peroxide and iron doses and the effect of the presence of radical scavengers. RESULTS AND DISCUSSION: It was observed that the 4-chlorophenol degradation efficiency decreased with increasing concentration and was independent of the initial solution pH in the UV process. 4-chlorophenol oxidation efficiency for an initial concentration of 100 mgl(-1) was around 89% after 300 min of irradiation in the UV process and no mineralization was achieved. The efficiency increased to > 99% with the UV/H2O2 process in 60 min of irradiation, although mineralization efficiency was still around 75% after 300 min of reaction time. Although the H2O2/4-CP molar ratio was kept constant, increasing initial 4-chlorophenol concentration decreased the treatment efficiency. It was observed that basic pHs were favourable in the UV/H2O2 process. The results showed that the photo-Fenton process was the most effective treatment process under acidic conditions. Complete disappearance of 100 mgl(-1) of 4-chlorophenol was achieved in 2.5 min and almost complete mineralization (96%) was also possible after only 45 min of irradiation. The efficiency was negatively affected from H2O2 in the UV/H2O2 process and Fe2+ in the photo-Fenton process over a certain concentration. The highest negative effect was observed with solutions containing PO4 triple ions. Required reaction times for complete disappearance of 100 mgl(-1) 4-chlorophenol increased from 2.5 min for an ion-free solution to 30 min for solutions containing 100 mgl(-1) PO4 triple ion and from 45 min to more than 240 min for complete mineralization. The photodegradation of 4-chlorophenol was found to follow the first-order law. CONCLUSION: The results of this study showed that UV irradiation alone can degrade 4-CP, although at very slow rates, but cannot mineralize the compound. The addition of hydrogen peroxide to the system, the so-called UV/H2O2 process, significantly enhances the 4-CP degradation rate, but still requires relatively long reaction periods for complete mineralization. The photo-Fenton process, the combination of homogeneous systems of UV/H2O2/Fe2+ compounds, produces the highest photochemical elimination rate of 4-CP and complete mineralization is possible to achieve in quite shorter reaction periods when compared with the UV/H2O2 process. RECOMMENDATIONS AND OUTLOOK: It is more cost effective to use these processes for only purposes such as toxicity reduction, enhancement of biodegradability, decolorization and micropollutant removal. However the most important point is the optimization of the reaction conditions for the process of concern. In such a case, AOPs can be used in combination with a biological treatment systems as a pre- or post treatment unit providing the cheapest treatment option. The AOP applied, for instance, can be used for toxicity reduction and the biological unit for chemical oxygen demand (COD) removal.     

Intermediate inhibition in the heterogeneous UV-catalysis using a TiO2 suspension system

Langmuir-Hinshelwood (L-H) kinetic expression was used to develop a basic mathematical model, which could describe the inhibition of intermediates in the photocatalysis of 2-chlorophenol (2-CP) in a suspended TiO2 system. Results showed that the photocatalytic oxidation of 2-chlorophenol followed the L-H type behavior and the reaction by-products displayed an inhibiting effect on the degradation rate. The inhibition was estimated by comparing to observed and estimated half-lives. The higher the initial concentration of 2-chlorophenol, the higher the inhibition of photocatalytic reaction. The L-H kinetic has been modified slightly in this study to rationalize the contrast of inhibited behavior and to improve in favor of a surface reaction. The concentrations of 2-chlorophenol were investigated ranging from 7.78 x 10(-5) to 7.78 x 10(-4) mol l(-1). The degradation of 2-chlorophenol in this reaction condition approximates a first-order kinetics to near-complete degradation. Calculated kinetic profiles are in an excellent agreement with the experimental observation. The results of the theoretical analysis can be used to estimate reaction rates in different initial concentrations of target compound.     

Oxidation of chlorophenols with hydrogen peroxide in the presence of goethite

The use of goethite (alpha-FeOOH) and hydrogen peroxide was recently found that they could effectively oxidize organic compounds. The study was to investigate the effect of goethite particle size, goethite concentration, Fe2+ and Fe3+ on the 2-chlorophenol oxidation. Results indicated that 2-chlorophenol can be decomposed with hydrogen peroxide catalyzed by goethite and the oxidation rate increased with decreasing goethite particle size. 2-Chlorophenol degradation was almost retarded with 0.8 g/l of goethite because ferrous ions could not be produced at this condition. Addition of Fe2+ and Fe3+ can enhance the catalytic oxidation rate of 2-chlorophenol very efficiently. In conclusion, the main mechanism of goethite catalyzing hydrogen peroxide to oxidize 2-chlorophenol may be due to the catalysis of ferrous ions and goethite surface.     

Degradation of 4-chlorophenol by microwave irradiation enhanced advanced oxidation processes

In this work the synergistic effects of several microwave assisted advanced oxidation processes (MW/AOPs) were studied for the degradation of 4-chlorophenol (4-CP). The efficiencies of the degradation of 4-CP in dilute aqueous solution for a variety of AOPs with or without MW irradiation were compared. The results showed that the synergistic effects between MW and H2O2, UV/H2O2, TiO2 photocatalytic oxidation (PCO) resulted in a high degradation efficiency for 4-CP. The potential of MW/AOPs for treatment of industrial wastewater is discussed.     

Surface-mediated formation of PBDD/Fs from the high-temperature oxidation of 2-bromophenol on a CuO/silica surface

As a model brominated hydrocarbon that may form brominated dioxins, we studied the surface-mediated, oxidative thermal degradation of 2-bromophenol on a supported copper oxide catalyst in a 1 mm i.d., fused silica flow reactor at a constant concentration of 90 ppm over a temperature range from 250 to 550 degrees C. Observed products included: dibenzo-p-dioxin (DD), 1-monobromodibenzo-p-dioxin (1-MBDD), dibromodibenzo-p-dioxin (DBDD), tribromodibenzo-p-dioxin (TrBDD), 4-monobromodibenzofuran (4-MBDF), 2,4,6-tribromophenol, 2,4- and 2,6-dibromophenol, and polybrominated benzenes. The results are compared and contrasted with previous work on surface catalyzed oxidative thermal degradation of 2-chlorophenol as well as our own work with the surface-catalyzed pyrolytic thermal degradation of 2-bromophenol. Typically 20 to 200x higher yields of PBDDs are observed for 2-bromophenol than for the analogous PCDDs for 2-chlorophenol. However the anticipated PBDF, 4,6-DBDF, was not observed and 4-MBDF was observed at very low yields. Surprisingly, the maximum yields of PBDDs were observed at higher temperatures than under pyrolytic conditions. This is attributed to regeneration of the catalytic surface due to the presence of oxygen. Higher yields of polybrominated phenols and polybrominated benzenes were also observed than for the analogous chlorinated phenols and benzenes from the oxidation of 2-chlorophenol. This can be attributed to the ease of bromination over chlorination based on the higher abundance of bromine atoms present for 2-bromophenol than chlorine atoms present for 2-chlorophenol.     

Ferrioxalate-mediated photodegradation and mineralization of 4-Chlorophenol

INTENTION, GOAL, SCOPE, BACKGROUND: Advanced oxidation processes are powerful methods which are capable of transforming refractory, nonbiodegradable and/or toxic organic compounds into harmless end products such as carbon dioxide and water. However, one commen problem of all advanced oxidation processes is the high demand of electrical energy for ultraviolet lamps, which causes high operational costs. Minimization of the required irradiation time, and therefore the energy consumption, by optimization of other reaction conditions such as catalyst-oxidant type and concentration, pH, temperature, pollutant/oxidant ratio etc., therefore continues to gain importance. OBJECTIVE: The main objective of this study was the minimization of the required irradiation time through optimization of the use of a newly patented catalyst, ferrioxalate, and also to compare the performance of this catalyst with the performance of other AOPs. METHODS: Oxidation of 4-chlorophenol by photo-Fenton process using potassium ferrioxalate as a mediator was studied in a lab scale photoreactor. The influence of parameters such as hydrogen peroxide and ferrioxalate concentrations, initial pH, power-output, oxalate/iron ratio and different iron sources was evaluated. An upflow photoreactor equipped with a 1000 Watt high-pressure mercury vapour lamp and operating in a recirculation mode was used during photodegradation experiments. The extent of the reduction of 4-chlorophenol, Total Organic Carbon and Chemical Oxygen Demand was used to evaluate the photodegradation reaction. RESULTS AND DISCUSSION: The optimum pH range observed was found to be 2.7-3. The efficiency of 4-chlorophenol oxidation increased with increasing concentrations of hydrogen peroxide and ferrioxalate, reaching a plateau after the addition of 10 and 0.072 mM of those reagents, respectively. Using an Oxalate/iron ratio of 12 was 18% less efficient than using a ratio of 3:1. The efficiency increased with increasing radiation power. However, this increase was not linear. The UV/ferrioxalate/H2O2 process, by which complete mineralization of 100 mg l(-1) 4-chlorophenol was achieved in 20 min of total reaction time, was the most efficient process among the alternatives applied. CONCLUSIONS: The use of ferrioxalate as the catalyst was found to be more efficient than the use of Fe(II) and Fe(III) iron species. It was possible to completely mineralize 4-chlorophenol. RECOMMENDATION AND OUTLOOK: The results of this study demonstrate that the ferrioxalate-mediated degradation of 4-chlorophenol requires less irradiation times than other advanced oxidation processes. There are mainly 19 phenol isomers and other toxic and nonbiodegradable organic compounds. We recommend that similar studies should be performed on many such compounds in order to attain a clear understanding of the performance of this catalyst. Because of its light sensitivity, this catalyst should be used immediately after its preparation. The use of low pressure mercury vapour lamps in this process should also be considered, since low power outputs may be enough for the process.     

不同电极降解2-氯苯酚

采用电沉积法制备了4种钛基二氧化铅电极,并与商业化的钛基RuO2电极进行了对比。分别用XRD和阳极极化曲线对电极性能进行了表征,并以2-氯苯酚为目标污染物,考察了6种电极的电催化氧化性能。研究结果表明,以钛板为基体的系列电极的综合性能优于以钛网为基体的相应电极。以β-PbO2为活性外层的二氧化铅电极的综合性能优于以RuO2为活性外层的电极。6种电极对2-氯苯酚降解反应均遵循一级反应动力学规律。其中Ti/α-PbO2/β-PbO2电极析氧电位最高,电催化性能最好,对2-氯苯酚的去除率可达99.3%。     

Fate of the organophosphorus pesticide profenofos in cotton fiber

Pesticides carried by cotton fiber are potential risk for production workers and consumers. Dissipation behaviour of a commonly used cotton pesticide profenofos in cotton fiber during growing period and scouring treatment was investigated. The results showed that profenofos in the fiber from the pre-opened and post-opened bolls both decreased to undetectable amounts 21?days after pesticide application. However, a minority of profenofos was converted to a strongly irritant compound, 4-bromo-2-chlorophenol and retained a non-negligible amount in cotton fiber even after 28?days. Profenofos and its degradation product could be completely removed during the conventional cotton scouring process. The degradation half-time of profenofos in scouring bath was only 3.0?min, and the degradation product was also 4-bromo-2-chlorophenol. Cotton products made of profenofos-carrying fiber are safe; however, the scouring waste should be detoxicated before discharge due to the accumulation of 4-bromo-2-chlorophenol in the scouring bath. These results could be useful for evaluating the risk of cotton fiber from the profenofos applied fields.     

固定化催化剂TiO2膜光催化降解三氯乙醛的研究

研究了负载于玻璃上的固定化催化剂TiO2膜光催化降解水中三氯乙醛的效果,探讨了TiO2膜光催化降解三氯乙醛的机理,考察了溶液pH值和三氯乙醛初始浓度埘TiO2膜光催化降解三氯乙醛的影响,并研究了固定化催化剂TiO2膜光催化降解三氯乙醛的动力学.结果表明,固定化催化剂TiO2膜光催化降解水中三氯乙醛的效果良好,当三氯乙醛初始浓度为2.25 mg/L时,在紫外光照时间3 h下,三氯乙醛的降解率高达100%.在相司紫外光照时间下,三氯乙醛的光催化降解率随着三氯乙醛初始浓度的增大而下降.在溶液pH=6.5时,三氯乙醛的降解效率最高.固定化催化剂TiO2膜光催化降解三氯乙醛的反应遵循一级反应动力学,反应速率常数随三氯乙醛初始浓度的增大而减小.     

Photoelectrocatalytic degradation of 4-chlorophenol and oxalic acid on titanium dioxide electrodes

Photocatalytically active thin TiO(2) films were produced by spin-coating or dip-coating an alkoxy precursor onto a transparent conducting electrode substrate and by thermal oxidation of titanium metal. The thin films were used to study the photoelectrocatalytic or photoelectrochemical degradation of oxalic acid and 4-chlorophenol (4-CP) under near UV (monochromatic, 365 nm) light irradiation. Degradation was monitored by a variety of methods. In the course of oxalic acid degradation, CO(2) formation accounted for up to 100% of the total organic carbon degradation for medium starting concentrations; for the degradation of 4-CP, less CO(2) was detected due to the higher number of oxidation steps, i.e. intermediates. Incident-photon-to-current conversion efficiency, educt degradation and product formation as well as Faradaic efficiencies were calculated for the degradation experiments. Quantum yields and Faradaic efficiencies were found to be strongly dependent on concentration, with maximum values (quantum yield) around 1 for the highest concentrations of oxalic acid.