复合式MBR处理印染废水

采用复合式膜生物反应器(MBR)对印染废水进行处理研究,系统在不同的停留时间下,各运行了一段时间,试验结果表明,复合式MBR与水解酸化预处理联用工艺处理印染废水,出水水质良好,而且比较稳定.系统出水COD、氨氮、色度较低,无SS.该工艺的特点是在MBR中加装了填料,既保证了微生物对有机物的去除效率,又大大降低了混合液中进入膜分离的悬浮物,有效控制了膜污染.     

电镀废水膜分离法问世

电镀废水回用技术的开发成果，首次将纳滤及反渗透技术集成用来处理电镀废水，这一成果已经申请“电镀废水处理零排放的膜分离方法”发明专利。该成果开发创新了新型膜组件等硬件技术和膜工艺设计、优化、管理运行等方面的软件，采用纳滤膜除去废水中的一价盐，并对镍离子预浓缩，再通过二级反渗透进一步浓缩镍，使其浓缩100倍，     

印染废水和抛煤机锅炉烟尘综合治理

印染废水和抛煤机锅炉烟尘是两大污染源.印染废水中较难处理的一是脱色,二是COD的去除.抛煤机锅炉排放烟尘浓度过高,经各种干式除尘器和多个湿式除尘器净化,仍不能达到国家规定的排放标准.本工艺运用烟尘的表面吸附、接触凝聚、气水冲击和气液接触等多种原理,实现了利用锅炉烟尘处理印染废水和利用印染废水净化锅炉烟尘的综合治理目的,经过二年多的工业化运行表明,这种工艺是合理的.也是可行的.     

普通活性污泥膜生物反应器处理洗车废水的应用研究

膜生物反应器是近年来发展起来的一种新型高效水处理设备。它将分离工程中的膜技术应用于好氧活性污泥处理系统，由膜组件取代传统生化处理技术中的二次沉淀池和砂滤池，由膜分离技术代替传统方法中的重力式沉淀泥水分离技术方式，具有简洁、高效等优点。采用普通活性污泥膜生物反应器工艺对天津某一洗车点洗车废水进行处理，并将处理出水回用于洗车。     

印染废水出水回用与实践

采用过滤-碳纤维吸附工艺对印染废水一级出水进行深度处理,废水COD可由80 mg/L降至30～40mg/L,出水水质完全满足生产工艺回用水要求.该技术具有工艺简单、投资少、运行费用低、操作简单等优点,特别适用于水资源短缺的中小印染企业.     

超滤/反渗透双膜技术深度处理印染废水

由于印染废水具有高盐度,可生化性差,使常规方法难于处理完全.采用超滤和反渗透双膜技术处理实际印染废水,考察了不同超滤膜对废水的预处理性能,研究了BW30和CPA2两种反渗透膜在不同操作条件下对印染废水的处理效果,并分析了相关膜通量下降的原因.结果表明,超滤能有效地去除废水浊度和大分子有机物,为反渗透提供良好的进水水质.两种反渗透膜的产水化学需氧量(COD)均小于10 mg/L,电导率小于80/μS/cm,其对有机物和盐的去除率分别可达99%和93%以上,显示该产水能回用于大部分印染工序.BW30膜产水水质稍好于CPA2,但通量低于CPA2.     

厌氧水解酸化-生物接触氧化工艺处理印染废水

印染废水的色度大,有机物含量高,可生化性差。针对这些特点,采用了厌氧水解酸化-生物接触氧化、气浮等工艺处理印染废水,结果表明,该工艺对印染废水有很好的处理效果,最终出水基本无色,达到纺织染整工业水污染物排放的一级标准（GB4287--1992）,处理成本较低。     

采油废水回注处理技术的现状及展望

阐述了目前采油废水回注处理的技术及工艺现状,重点探讨了膜分离技术在采油废水回注处理中的研究及应用情况,分析了各技术存在的问题,并展望了采油废水回注处理技术的发展趋势。     

加压生物氧化法处理印染废水的动力学研究

加压生化法与其他处理印染废水的方法相比．具有工艺简单,耐冲击能力强、投资低、操作参数仪表控制、剩余污泥量少等优点。探讨了在加压曝气条件下处理印染废水的生化反应机理．测定其动力学参数．建立加压生物氧化法处理印染废水的生物氧化反应动力学模型,为印染废水的加压生化处理提供了可靠的设计与运行参数。     

印染废水治理技术研究及展望

介绍了印染废水各种治理技术——化学处理法、物理化学处理法及生物化学处理法等，并展望了印染废水治理技术的发展趋势。     

Sorption and desorption of Cu and Cd by macroalgae and microalgae

The sorption and desorption of Cu and Cd by two species of brown macroalgae and five species of microalgae were studied. The two brown macroalgae, Laminaria japonica and Sargassum kjellmanianum, were found to have high capacities at pHs between 4.0 and 5.0 while for microalgae, optimum pH lay at 6.7. The presence of other cations in solution was found to reduce the sorption of the target cation, suggesting a competition for sorption sites on organisms. Sorption isotherms obeyed the Freundlich equation, suggesting involvement of a multiplicity of mechanisms and sorption sites. For the microalgae tested, Spirulina platensis had the highest capacity for Cd, followed by Nannochloropsis oculata, Phaeodactylum tricornutum, Platymonas cordifolia and Chaetoceros minutissimus. The reversibility of metal sorption by macroalgae was examined and the results show that both HCl and EDTA solutions were very effective in desorbing sorbed metal ions from macroalgae, with up to 99.5% of metals being recovered. The regenerated biomass showed undiminished sorption performance for the two metals studied, suggesting the potential of such material for use in water and wastewater treatment.     

Kinetic and structural relationships of transition monomeric and oligomeric carboxyl- and choline-esterases

The kinetic and structural relationships of eight electrophoretically pure mammalian serum and liver serine carboxylesterases (CE) and cholinesterases (ChE) have been studied. Eight CE's and ChE's, which were fully resolved but only partially purified, provided additional information. Five of the electrophoretically pure esterases were monomeric, and of these, four belonged to a new and widely distributed class. These four monomeric esterases hydrolyzed choline esters, but at widely differing rates. Thus two were termed monomeric butyrylcholinesterases, mBuChE I and II, and two were monomeric CE's (mCE). The rabbit liver mCE was not a subunit of the oligomeric CE (oCE), although the oCE also hydrolyzed choline esters at a very low rate. The complex kinetics of the mCE's, mBuChE's, oCE's, and of the oligomeric BuChE's of horse and human serum could be interpreted according to a single reaction scheme involving an allosteric site and the equation derived from it. Thus activation and inhibition at high substrate concentrations, together with sigmoidal activity versus substrate concentration plots, all of which characterize the reactions of these esterases, could be interpreted by a single scheme and equation. Structural and kinetic comparisons showed a progressive transition of properties from the oCE's through the mCE's to the oBuChE's. One of the purified mCE's was from horse serum, and it exhibited physical and kinetic properties unlike those of the liver mCE's or oCE's.     

Persistence and dissipation kinetics of trifloxystrobin and tebuconazole in onion and soil

The persistence and dissipation kinetics of trifloxystrobin and tebuconazole on onion were studied after application of their combination formulation at a standard and double dose of 75 + 150 and 150 + 300 g a.i. ha^?1. The fungicides were extracted with acetone, cleaned-up using activated charcoal (trifloxystrobin) and neutral alumina (tebuconazole). Analysis was carried out by gas chromatograph (GC) and confirmed by gas chromatograph mass spectrometry (GC-MS). The recovery was above 80% and limit of quantification (LOQ) 0.05 mg kg^?1 for both fungicides. Initial residue deposits of trifloxystrobin were 0.68 and 1.01 mg kg^?1 and tebuconazole 0.673 and 1.95 mg kg^?1 from standard and double dose treatments, respectively. Dissipation of the fungicides followed first-order kinetics and the half life of degradation was 6–6.6 days. Matured onion bulb (and field soil) harvested after 30 days was free from fungicide residues. These findings suggest recommended safe pre-harvest interval (PHI) of 14 and 25 days for spring onion consumption after treatment of Nativo 75 WG at the standard and double doses, respectively. Matured onion bulbs at harvest were free from fungicide residues.     

Sorption and Desorption Behavior of Chloroanilines and Chlorophenols on Montmorillonite and Kaolinite

The bioavailability of pollutants, pesticides and/or their degradation products in soil depends on the strength of their sorption by the different soil components, particularly by the clay minerals. This study reports the sorption-desorption behavior of the environmentally hazardous industrial pollutants and certain pesticides degradation products, 3-chloroaniline, 3,4-dichloroaniline, 2,4,6-trichloroaniline, 4-chlorophenol, 2,4-dichlorophenol and 2,4,6-trichlorophenol on the reference clays kaolinite KGa-1 and Na-montmorillonite SWy-l. In batch studies, 2.0 g of clay were equilibrated with 100.0 mL solutions of each chemical at concentrations ranging from 10.0 to 200.0 mg/L. The uptake of the compounds was deduced from the results of HPLC-UV-Vis analysis. The lipophilic species were best retained by both clay materials. The most lipophilic chemical used in the study, 2,4,6-trichloroaniline, was also the most strongly retained, with sorption of up to 8 mg/g. In desorption experiments, which also relied on HPLC-UV-Vis technique, 2,4,6-trichloroaniline was the least desorbed from montmorillonite. However, on kaolinite all of the compounds under study were irreversibly retained. The experimental data have been modelled according to the Langmuir and Freundlich isotherms. A hypothesis is proposed concerning the sorption mechanism and potential applications of the findings in remediation strategies have been suggested.     

Sorption and desorption behavior of chloroanilines and chlorophenols on montmorillonite and kaolinite

The bioavailability of pollutants, pesticides and/or their degradation products in soil depends on the strength of their sorption by the different soil components, particularly by the clay minerals. This study reports the sorption-desorption behavior of the environmentally hazardous industrial pollutants and certain pesticides degradation products, 3-chloroaniline, 3,4-dichloroaniline, 2,4,6-trichloroaniline, 4-chlorophenol, 2,4-dichlorophenol and 2,4,6-trichlorophenol on the reference clays kaolinite KGa-1 and Na-montmorillonite SWy-l. In batch studies, 2.0 g of clay were equilibrated with 100.0 mL solutions of each chemical at concentrations ranging from 10.0 to 200.0 mg/L. The uptake of the compounds was deduced from the results of HPLC-UV-Vis analysis. The lipophilic species were best retained by both clay materials. The most lipophilic chemical used in the study, 2,4,6-trichloroaniline, was also the most strongly retained, with sorption of up to 8 mg/g. In desorption experiments, which also relied on HPLC-UV-Vis technique, 2,4,6-trichloroaniline was the least desorbed from montmorillonite. However, on kaolinite all of the compounds under study were irreversibly retained. The experimental data have been modelled according to the Langmuir and Freundlich isotherms. A hypothesis is proposed concerning the sorption mechanism and potential applications of the findings in remediation strategies have been suggested.     

Bacterial and archaeal diversity in oil fields and reservoirs and their potential role in hydrocarbon recovery and bioprospecting

Environmental Science and Pollution Research - Hydrocarbon is a primary source of energy in the current urbanized society. Considering the increasing demand, worldwide oil productions are declining...     

畜禽养殖业污染与循环经济

解决畜禽养殖业的污染问题要以充分利用资源为根本出发点，通过对污染全过程控制及废物综合利用，达到畜禽粪便的减量化、无害化、资源化，走循环经济的发展道路。     

Degradation in soil and water and ecotoxicity of rimsulfuron and its metabolites.

The degradation and ecotoxicity of sulfonylurea herbicide rimsulfuron and its major metabolites were examined in batch samples of an alluvial sandy loam and in freshwater. An HPLC-DAD method was adapted to simultaneously identify and quantify rimsulfuron and its metabolites, which was successfully validated by GC-MS analysis. In aqueous solutions, pure rimsulfuron was rapidly hydrolyzed into metabolite 1 (N-(4,6-dimethoxypyrimidin-2-yl)-N-(3-(ethylsulfonyl)-2-pyridinylurea)), which itself was transformed into the more stable metabolite 2 (N-((3-(ethylsulfonyl)-2-pyridinyl)-4,6-dimethoxy-2-pyrimidineamine)), with half-life (t(1/2)) values of 2 and 2.5 days, respectively. Hydrolysis was instantaneous under alkaline conditions (pH = 10). In aqueous suspensions of the alluvial soil (pH = 8), formulated rimsulfuron had a half-life of 7 days, whereas that of metabolite 1 was similar to that in water (about 3.5 days). The degradation of the two major metabolites was also studied in soil suspensions with the pure compounds at concentrations ranging from 1 to 10 mg l(-1). The half-life of metabolite 1 ranged from 3.9 to 5 days, close to the previous values. Metabolite 2 was more persistent and its degradation is strongly dependent on the initial concentration (C0): half-life values ranged from 8.1 to 55 days at 2-10 mg l(-1), respectively. These values are higher than those determined from the kinetics of metabolite 1 transformation into metabolite 2 (t(1/2) = 8-19 days). The ecotoxicity of the three chemicals was evaluated through their effect on Daphnia magna and Vibrio fischeri (Microtox bioassay). No effect was observed on D. magna with 24 and 48 h acute toxicity tests. Similarly, no toxic effect was observed with the Microtox test for the three chemicals in the range of concentrations tested that included the field application dose. Thus, being of low persistence and lacking acute toxicity, these chemicals present a low environmental risk. However, chronic effects should be studied in order to confirm the safety of rimsulfuron and its major metabolites.     

Isocyanatocyclohexane and isothiocyanatocyclohexane levels in urban and industrial areas and possible emission-related activities

Isocyanatocyclohexane and isothiocyanatocyclohexane are becoming relevant compounds in urban and industrial air, as they are used in important amounts in automobile industry and building insulation, as well as in the manufacture of foams, rubber, paints and varnishes. Glass multi-sorbent tubes (Carbotrap, Carbopack, Carboxen) were connected to LCMA-UPC pump samplers for the retention of iso- and isothiocyanatocyclohexanes. The analysis was performed by automatic thermal desorption (ATD) coupled with capillary gas chromatography (GC)/mass spectrometry detector (MSD). TD-GC/MS was chosen as analytical method due to its versatility and the possibility of analysis of a wide range of volatility and polarity VOC in air samples. The method was satisfactory sensitive, selective and reproducible for the studied compounds. The concentrations of iso- and isothioisocyanatocyclohexanes were evaluated in different urban, residential and industrial locations from extensive VOC air quality and odour episode studies in several cities in the Northeastern edge of Spain. Around 200–300 VOC were determined qualitatively in each sample. Higher values of iso- and isothiocyanatocyclohexane were found in industrial areas than in urban or residential locations. The concentrations ranged between n.d.−246 and n.d.−29 μg m⁻³ for isocyanatocyclohexane and isothiocyanatocyclohexane, respectively, for industrial areas. On the other hand, urban and residential locations showed concentrations ranging between n.d.−164 and n.d.−29 μg m⁻³ for isocyanatocyclohexane and isothiocyanatocyclohexane, respectively. The site location (urban or industrial), the kind and nearness of possible iso- and isothiocyanatocyclohexane emission activities (industrial or building construction) and the changes of wind regimes throughout the year have been found the most important factors influencing the concentrations of these compounds in the different places.