活性炭柱中砂垫层在微污染水源水处理工艺中的应用

以嘉兴市某水厂沉后水为进水进行实验,研究炭砂滤池对污染物的去除性能,以及炭砂滤池取代活性炭＋砂滤池的可能性,探讨了短流程工艺的适用性。结果表明,炭砂滤池能有效去除水中的浊度、氨氮、CODMn和铁、锰等污染物,与活性炭柱相比,炭砂滤池在降低出水浊度和水中颗粒数方面具有一定优势,即砂垫层对控制出水浊度和保障微生物安全能够起到积极作用。在实验条件下,增加活性炭层厚度或者降低滤速,在一定程度上有利于提高对CODMn的去除率。在设计滤速为9～10 m/h,CODMn〈4.5 mg/L时,可直接以炭砂滤池取代活性炭池＋砂滤池,仍然能保证出水CODMn〈3 mg/L。     

超滤膜与后置砂滤池净水效果对比

将"混凝沉淀-前置砂滤池-升流式生物活性炭滤池"工艺出水分别进入后砂滤池与超滤膜组件,比较两者对水中的浊度、COD_(Mn)、氨氮、颗粒数及微型生物的去除效果。结果表明:超滤膜平均去浊率为31.57%,去浊优势不是很明显,但明显高于后砂滤池去浊率;对于COD_(Mn)的去除,后砂滤池的平均去除率为6.80%,优于超滤膜;后砂滤池对氨氮的去除率达到50.08%,相比超滤膜优势很明显;超滤膜出水颗粒数相对较平稳,且能有效保证饮用水生物安全性。后砂滤池的微絮凝作用,可使其出水浊度、COD_(Mn)及微型生物数量均有所降低,但其对微型生物的去除效果与超滤膜相比仍有不足。     

慢滤池去除污水中邻苯二甲酸二(2-乙基己基)酯的效能

将慢滤池用于污水二级出水的深度处理,并利用小试装置研究了慢滤池去除邻苯二甲酸二(2-乙基己基)酯(DEHP)的效能。慢滤池采用粒径为0.4～0.6 mm,厚度为800 mm的石英砂做滤料并以0.1 m/h的恒定滤速运行。实验结果表明,慢滤池出水浊度、COD和色度远低于现行《城市污水再生利用城市杂用水水质标准》(GB/T18920-2002)的相应数值。污水二级处理出水中DEHP浓度为6.1～62.8μg/L时,经过慢滤池过滤后,DEHP浓度降为1.7～7.3μg/L。当接纳282.8μg/L的DEHP冲击负荷时,慢滤池出水DEHP仍能低于10μg/L。实验证明,慢滤池内的生物膜吸附过滤和生物降解共同保证了慢滤池去除DEHP的良好性能。     

曝气生物活性炭滤池深度处理高浓度氨氮原水

实验研究曝气生物活性炭滤池对于高浓度氨氮原水的处理效果以及工艺运行稳定情况。以某自来水厂常规工艺沉淀池出水预加硫酸铵作为研究对象,原水氨氮平均浓度3.67 mg/L,实验条件:温度31.2℃,pH 7.13,滤速8~12 m/h,气水比0.5和1。采用3种不同工况条件进行实验,确定滤速10 m/h和气水比0.5的为最佳运行工况。在此工况下曝气生物活性炭滤池对于氨氮和COD Mn的平均去除率分别达到87.5%和19.2%,亚硝酸盐积累率为0.9%;出水氨氮浓度达到生活饮用水卫生标准GB5749-2006。同时炭滤池的出水浊度相比进水略微上升。     

水温对慢滤池深度处理污水的性能影响

将慢滤池用于污水二级出水的深度处理,利用一套小试装置研究了水温对慢滤池性能的影响。对比慢滤池在冬季和夏季的运行数据,结果发现:从夏季(23~25℃)转到冬季(10~14℃)时,慢滤池对浊度、COD、色度和细菌总数的去除率分别下降了12.5%、26.5%、22.9%和5.8%。水温下降后,虽然慢滤除污染物的整体效果下降,但却对各污染指标表现出不同的规律:水温对COD去除影响最大,而对浊度去除的影响相对较小。在慢滤进水浊度较低的情况下,水温对色度去除的影响程度会位于对COD去除和浊度去除的影响程度之间。无论温度如何变化,慢滤均能保持良好的细菌去除效果。     

2种曝气生物滤池深度处理含CMC模拟退浆废水

采用陶粒滤料和活性炭滤料的2组曝气生物滤池(BAF)处理含CMC模拟退浆废水,在水力负荷0.071 m3·(m2·h)-1、水力停留时间24 h条件下,分析曝气生物滤池对COD、CMC和浊度去除效果和曝气强度对滤池运行的影响,研究滤柱高度方向污染物去除规律以及和微生物量、微生物活性间的关系。研究结果表明,随着气水比的增大,生物滤池对COD、CMC的去除效率增大,强烈的曝气作用会引起出水浊度增大。在气水比为4∶1的条件下,2组生物滤池对COD和CMC的平均去除率分别约为72%和65%、67%和62%。曝气生物滤池对COD、CMC、浊度的主要去除区域分别位于滤柱1.5、1.3和1.1 m高度以下区域。陶粒滤柱相对活性炭滤柱微生物量略高,两组滤池单位滤料微生物量和微生物脱氢酶活性沿滤柱高度方向变化趋势相似。两组滤池对CMC的去除主要依靠吸附作用,生物降解部分仅占CMC总去除率的34.7%和26.1%。     

上向流好气滤池冬季挂膜启动及运行参数探讨

好气滤池同时具有普通滤池和曝气生物滤池的优点,能对二级出水中的COD、氨氮和浊度等指标进一步去除,提高再生水水质。试验探讨了冬季好气滤池的挂膜启动方法和运行参数,提出采用逐渐增加流量到设计流量的自然挂膜法,同时提出运行采用上向流;滤速1 m/h;气水比采用（1～3）∶1;填料填充高度与滤料直径有关;出水水头损失增加到1 m作为过滤周期的终点;适宜的冲洗强度冲洗滤池后,4 h内能恢复到滤池反冲洗前的处理状态。冬季低温条件延长了好气滤池的挂膜启动时间,但不影响挂膜质量;为保证出水质量,对好气滤池的运行滤速要通过试验确定。     

反冲洗周期对生物除锰滤池去除效果的影响

反冲洗周期是生物除铁除锰滤池的一个重要运行参数,实验中分别设定反冲洗周期为24、48和72h,考察反冲洗周期对成熟稳定运行的滤柱出水铁、锰、氨氮和浊度的影响。结果表明,不同反冲洗周期,滤柱对铁、锰和氨氮均有很好的去除效果,出水中的总Fe、Mn“和NH？-N的平均浓度分别为0．018、0．003和0．016mg／L,0．010、0．001和0．014mg/L,0．013、0．001和0．014mg／L,均远低于国家标准,说明反冲洗周期变化对三者的去除效果没有影响。反冲洗周期为24、48和72h时,出水平均浊度分别为0．27、0．38和0．57NTU,反冲洗周期越长,出水浊度越高。滤柱沿程浊度分析发现,浊度主要在0～O．4m去除,出水浊度与滤层厚度无关。反冲洗后5rain出水浊度为3．16NTU,15min降到了1NTU以下,25min降到了0．5NTU,60min大约降到了反冲洗前的水平。     

反冲洗周期对生物除锰滤池去除效果的影响简

反冲洗周期是生物除铁除锰滤池的一个重要运行参数,实验中分别设定反冲洗周期为24、48和72 h,考察反冲洗周期对成熟稳定运行的滤柱出水铁、锰、氨氮和浊度的影响。结果表明,不同反冲洗周期,滤柱对铁、锰和氨氮均有很好的去除效果,出水中的总Fe、Mn²⁺和NH₄⁺-N的平均浓度分别为0.018、0.003和0.016 mg/L,0.010、0.001和0.014 mg/L,0.013、0.001和0.014 mg/L,均远低于国家标准,说明反冲洗周期变化对三者的去除效果没有影响。反冲洗周期为24、48和72 h时,出水平均浊度分别为0.27、0.38和0.57 NTU,反冲洗周期越长,出水浊度越高。滤柱沿程浊度分析发现,浊度主要在0~0.4 m去除,出水浊度与滤层厚度无关。反冲洗后5 min出水浊度为3.16 NTU,15 min降到了1 NTU以下,25 min降到了0.5 NTU,60 min大约降到了反冲洗前的水平。     

基于高效絮凝沉淀池与翻板滤池组合工艺的工程案例

以银川市某水厂为例,评估高效絮凝沉淀池与翻板滤池组合工艺的工程应用效果。结果表明,高效絮凝沉淀池与翻板滤池组合工艺能够适应较大水质波动,具有一定抗冲击负荷能力。其浊度去除率和高锰酸盐指数(以COD_Mn计)去除率较高,出水水质满足《生活饮用水卫生标准》(GB/T5749-2006)。通过调整排泥量和污泥回流比,能够有效解决沉淀池泥位超标问题。根据翻板滤池的过滤负荷和滤水阀门的开度调整反冲洗周期,能够提高过滤效率,节约电耗。少量无烟煤滤料的流失对翻板滤池出水浊度无影响。本研究结果可为低温低浊水处理工程提供设计经验和工程案例参考。     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

不同泥源对厌氧氨氧化反应器启动的影响

采用2套上流式生物膜反应器,分别接种少量厌氧氨氧化污泥和大量硝化污泥,考察其对厌氧氨氧化反应器启动的影响。污泥接种入反应器后,测得接种厌氧氨氧化污泥的反应器(R1)内MLSS为0.22 g/L,另一个反应器(R2)MLSS为2.7 g/L。与直接接种厌氧氨氧化污泥相比,R1经过72 d的运行才显现出厌氧氨氧化特性。经过114 d的培养,前者氮去除速率由0.23 kg/(m3.d)提升到5.29 kg/(m3.d),总氮去除率大于89%;R2的氮去除速率由0.01 kg/(m3.d)提升到1.1 kg/(m3.d),总氮去除率大于84.6%。说明普通污泥启动需要一个较长的筛选过程,直接接种少量的厌氧氨氧化污泥比接种普通的污泥能够更快启动厌氧氨氧化反应器。     

生物质快速热裂解主要参数对生物油产率的影响

以松木木屑为原料,在自制的小型流化床上,开展了生物质热裂解温度、生物质粒径和进料速率对生物油产率的影响实验研究.结果表明,在热裂解温度分别为450、475、500、525和550℃条件下,当热裂解温度为500℃时,生物油产率最高,平均产率达到53.33%(质量百分比).反应温度越高,炭产量越低,不可冷凝气体产量越高,气体发热值越高;粒径＜1 mm的生物质其粒径对生物油产率影响不大;生物质进料速率增加时,生物油产率增加.本研究为生物能的利用提供了新的途径.     

Visualisation of the complexity of EUSES

The interdependencies of parameters applied in the models of EUSES are visualised in a directed connectivity graph. The parameters (inputs, defaults, state variables, outputs) are represented by boxes (nodes) and their relations by lines (edges). The visualisation, on the one hand, clarifies the complexity of the models in EUSES and, on the other hand, creates an overview and transparency. The parameters’ relations to each other can be recognised faster, and the models can be better understood. The complexity was quantified by the number (variety), kind (substance parameter, physico-chemical parameter, concentration, other parameters), and depth (dimension) of the parameter and the number of relations (connectivity). The variety of EUSES (without the modelsSimple Treat andSimple Box whose interior structure is not documented and without the effect and risk characterisation) amounts to 466, the connectivity to 961, and the maximal dimension is 21.     

造纸废水混凝处理中SFT助凝替代性研究

中小造纸厂废水处理常用PAC作混凝剂 ,PAM作助凝剂。由于PAM成本很高 ,影响了处理设备的投运率。用超细滑石粉 (SFT)替代PAM助凝 ,与混凝剂PAC配合 ,其混凝处理效果基本相当 ,但是处理成本降低 0 .10元 /m3 。由于SFT属环境无害材料 ,不会给排泥带来二次污染     

产油微藻培养与回收的关键技术研究进展

寻找廉价而高效的替代原料是实现生物柴油产业化的关键所在.微藻以含油量高、生长周期短、环境适应能力强、生物产量高等优点,有望成为一种极具潜力的生物柴油生产原料.然而,目前尚存在微藻培养低效成本高和微藻回收效率低两大难题.综述了微藻培养与回收过程中的关键技术,并对存在的两大难题及其改进技术进行了详细的探讨.最后,总结并展望了微藻培养、回收技术未来的发展趋势.     

活性炭三维电极法对印染废水的处理研究

对三维电极方法处理印染废水进行了实验研究,初步探讨了活性炭三维电极法处理印染废水的机理,对影响处理效果的各种要素,如反应时间、槽电压和pH值等进行了条件实验,得出了活性炭三维电极法处理印染废水的最佳运行条件为:停留时间120-180 min,槽电压25～30 V,进水pH值6.5～7.5。结果表明,该反应器能有效地降低废水色度,有较高的COD去除效率,并能提高印染废水的可生化性。     

Evaluation of the presence of drugs of abuse in tap waters

A total of seventy samples of drinking water were tested for non-controlled and illicit drugs. Of these, 43 were from Spanish cities, 15 from seven other European countries, three from Japan and nine from seven different Latin American countries. The most frequently detected compounds were caffeine, nicotine, cotinine, cocaine and its metabolite benzoylecgonine, methadone and its metabolite EDDP. The mean concentrations of non-controlled drugs were: for caffeine 50 and 19 ng L⁻¹, in Spanish and worldwide drinking water respectively and for nicotine 13 and 19 ng L⁻¹. Illicit drugs were sparsely present and usually at ultratrace level (<1 ng L⁻¹). For example, cocaine has mean values of 0.4 (Spain) and 0.3 ng L⁻¹ (worldwide), whereas for benzoylecgonine, these mean values were 0.4 and 1.8 ng L⁻¹, respectively. Higher concentrations of benzoylecgonine were found in Latin American samples (up to 15 ng L⁻¹). No opiates were identified in any sample but the presence of methadone and EDDP was frequently detected. Total mean values for EDDP were 0.4 ng L⁻¹ (Spain) and 0.3 ng L⁻¹ (worldwide). Very few samples tested positive for amphetamines, in line with the reactivity of chlorine with these compounds. No cannabinoids, LSD, ketamine, fentanyl and PCP were detected.