Dynamics and mitigation of six pesticides in a “Wet” forest buffer zone

Pesticide pollution is one of the main current threats on water quality. This paper presents the potential and functioning principles of a “Wet” forest buffer zone for reducing concentrations and loads of glyphosate, isoproturon, metazachlor, azoxystrobin, epoxiconazole, and cyproconazole. A tracer injection experiment was conducted in the field in a forest buffer zone at Bray (France). A fine time-scale sampling enabled to illustrate that interactions between pesticides and forest buffer substrates (soil and organic-rich litter layer), had a retarding effect on molecule transfer. Low concentrations were observed for all pesticides at the forest buffer outlet thus demonstrating the efficiency of “Wet” forest buffer zone for pesticide dissipation. Pesticide masses injected in the forest buffer inlet directly determined concentration peaks observed at the outlet. Rapid and partially reversible adsorption was likely the major process affecting pesticide transfer for short retention times (a few hours to a few days). Remobilization of metazachlor, isoproturon, desmethylisoproturon, and AMPA was observed when non-contaminated water flows passed through the forest buffer. Our data suggest that pesticide sorption properties alone could not explain the complex reaction mechanisms that affected pesticide transfer in the forest buffer. Nevertheless, the thick layer of organic matter litter on the top of the forest soil was a key parameter, which enhanced partially reversible sorption of pesticide, thus retarded their transfer, decreased concentration peaks, and likely increased degradation of the pesticides. Consequently, to limit pesticide pollution transported by surface water, the use of already existing forest areas as buffer zones should be equally considered as the most commonly implemented grass buffer strips.     

Study of the spatial divergence features and motivating factors of energy green consumption levels in “2+26” cities

Environmental Science and Pollution Research - The level of energy green consumption is an essential factor influencing China’s economy’s high-quality development. In this paper, we...     

Biodegradation of α and β isomers of endosulphan and endosulphan sulphate in Indian soils

Abstract

The degradation of α and β isomers of endosulphan and endosulphan sulphate in four sterilized and non sterilized Indian soils under laboratory conditions was studied. Degradation was found to be more in non‐sterilized as compared to the sterilized soil. The half life of α‐endosulphan, β‐endosulphan and endosulphan sulphate was found to be 136.8, 273 and 301 days in sterilized Alfisol and 55, 256 and 277 days in non‐sterilized Alfisol, respectively. α‐Endosulphan degraded more readily than β‐endosulphan and endosulphan sulphate under both sterilized and non‐sterilized soil conditions.     

Analysis of the influence of urban form and materials on sensible heat flux — a case study of Japan's largest housing development “Tama New Town”

In this study, the relationship between the form and materials of urban blocks and sensible heat flux from total surfaces was analyzed in the case of `Tama New Town', which is one of the largest housing developments in Japan and is under continuing development. First, urban blocks were divided into five categories depending on the building plot types. The characteristics of the form and thermal properties of each building, as well as the land cover condition (area of vegetation, bare soil, asphalt pavement, and built area) of each category was considered. Furthermore, 6 urban blocks were selected for numerical simulation of heat balance of the total surfaces, and sensible heat flux from the total surfaces of each urban block on clear sky summer day was calculated. It was confirmed that the influence of the direction that buildings faced and floor area ratio was as great as that of building materials upon the amount of sensible heat flux in each urban block.     

Comment on “Methylcyclopentadienyl Manganese Tricarbonyl as an Antiknock: Composition and Fate of Manganese Exhaust Products”

In an article published in the August 1975, Journal of the Air Pollution Control Association entitled “Methylcyclopentadienyl Manganese Tricarbonyl as an Antiknock: Composition and Pate of Manganese Exhaust Products,” the authors conclude that, “… use of MMT in gasoline will result in no public health hazards, because of the low toxicity of manganese and because of the very low concentration of MMT that would be used in gasoline …. If all gasoline contained 0.1 g Mn/gal, the amount of airborne Mn its exhaust would contribute to urban areas would contribute to urban areas would be only 0.02-0.2 μg/m³, with a median value of 0.05 μg/m³.”     

Using of “pseudo-second-order model” in adsorption

A research paper's contribution exists not only in its originality and creativity but also in its continuity and development for research that follows. However, the author easily ignores it. Citation error and quotation error occurred very frequently in a scientific paper. Numerous researchers use secondary references without knowing the original idea from authors. Sulaymon et al. (Environ Sci Pollut Res 20:3011–3023, 2013) and Spiridon et al. (Environ Sci Pollut Res 20:6367–6381, 2013) presented wrong pseudo-second-order models in Environmental Science and Pollution Research, vol. 20. This comment pointed the errors of the kinetic models and offered information for citing original idea of pseudo-second-order kinetic expression. In order to stop the proliferation of the mistake, it is suggested to cite the original paper for the kinetic model which provided greater accuracy and more details about the kinetic expression.     

Simultaneous biodegradation of dimethyl sulfide and 1-propanethiol by Pseudomonas putida S-1 and Alcaligenes sp. SY1: “Lag” cause,reduction, and kinetics exploration

Environmental Science and Pollution Research - Simultaneous biodegradation of malodorous 1-propanethiol (PT) and dimethyl sulfide (DMS) by Pseudomonas putida S-1 and Alcaligenes sp. SY1 was...     

Decontamination of polycyclic aromatic hydrocarbons and nonylphenol from sewage sludge using hydroxypropyl-β-cyclodextrin and evaluation of the toxicity of leachates

A decontamination technique based in cyclodextrin extraction has been developed to eliminate nonylphenol (NP) and 16 polycyclic aromatic hydrocarbons (PAHs; the US Environmental Protection Agency priority pollutants list) from sewage sludge. In a first step, PAHs and NP were characterised in six sludges to determine contamination levels according to limit values proposed by the European Union Sludge Directive draft. There were few variations in the total PAHs content with levels of 1.88 to 3.05 mg kg^?1. Three-ring PAHs predominated, but fluoranthene and pyrene were also present. None of the sludge exceeded the PAHs limit proposed by the European Union’s draft Directive. On the contrary, NP content in four of the six sludges was over the recommended limits of 50 mg kg^-1 for NP ethoxylates. With the aim of obtaining NP values below the concentration limits proposed to use the sewage sludge as agricultural amendments, a preliminary study using hydroxypropyl-β-cyclodextrin (HPBCD) extractions as a decontamination technique was carried out. About 90 % of NP content was removed with only one extraction with HPBCD, whereas after three sequential extractions using an aqueous solution without HPBCD, the NP extraction percentage was less than 1 %. Simultaneously, PAHs extraction percentages obtained with HPBCD were also much higher than when aqueous solution was used, especially in the case of two- and three-ring PAHs. Finally, the potential environmental hazard of HPBCD leachates to aquatic organisms (Daphnia magna) was tested. These results indicate that the treatment of sewage sludge with cyclodextrin could allow their safe use as fertiliser in agriculture.     

Field evaluations of newly available “interference-free” monitors for nitrogen dioxide and ozone at near-road and conventional National Ambient Air Quality Standards compliance sites

Long-standing measurement techniques for determining ground-level ozone (O₃) and nitrogen dioxide (NO₂) are known to be biased by interfering compounds that result in overestimates of high O₃ and NO₂ ambient concentrations under conducive conditions. An increasing near-ground O₃ gradient (NGOG) with increasing height above ground level is also known to exist. Both the interference bias and NGOG were investigated by comparing data from a conventional Federal Equivalent Method (FEM) O₃ photometer and an identical monitor upgraded with an “interference-free” nitric oxide O₃ scrubber that alternatively sampled at 2 m and 6.2 m inlet heights above ground level (AGL). Intercomparison was also made between a conventional nitrogen oxide (NO_x) chemiluminescence Federal Reference Method (FRM) monitor and a new “direct-measure” NO₂ NO_x 405 nm photometer at a near-road air quality measurement site. Results indicate that the O₃ monitor with the upgraded scrubber recorded lower regulatory-oriented concentrations than the deployed conventional metal oxide–scrubbed monitor and that O₃ concentrations 6.2 m AGL were higher than concentrations 2.0 m AGL, the nominal nose height of outdoor populations. Also, a new direct-measure NO₂ photometer recorded generally lower NO₂ regulatory-oriented concentrations than the conventional FRM chemiluminescence monitor, reporting lower daily maximum hourly average concentrations than the conventional monitor about 3 of every 5 days.

Implications: Employing bias-prone instruments for measurement of ambient ozone or nitrogen dioxide from inlets at inappropriate heights above ground level may result in collection of positively biased data. This paper discusses tests of new regulatory instruments, recent developments in bias-free ozone and nitrogen dioxide measurement technology, and the presence/extent of a near-ground O₃ gradient (NGOG). Collection of unbiased monitor inlet height–appropriate data is crucial for determining accurate design values and meeting National Ambient Air Quality Standards.     

Pollution of water in Africa: a review of contaminants and fish as biomonitors and analytical methodologies—the case of Senegal

Environmental Science and Pollution Research - Environmental pollution is one of the major problems facing human health, ecosystems, and biodiversity. This is particularly the case for water...     

Comment on “Mortality and Air Pollution: Revisited”

Abstract

Test-to-test variability has been observed by many current testing methods, including the Federal Test Procedure, the IM240 dynamometer test, the idle test common to many Inspection and Maintenance programs, and on-road remote sensing. The variability is attributable to the vehicle, not to the testing procedure. Because the vehicles are the dominant source of variability, the only way such vehicles can be reliably identified is through the use of multiple tests. The emissions variability increases with increasing average emissions, and it appears to be prevalent among the few newer technology vehicles with defective, but untampered, closed-loop emissions control systems (1981 and newer models). In one fleet the variable emitters constitute 2.2% to 4.8% of the vehicles and contribute 8.5% to 22% of the total carbon monoxide emissions. Scheduled I/M programs that fail to ensure repair of these vehicles allow a significant portion of vehicles with excess emissions to escape reduction measures.     

Enhancing phytoextraction of Cd by combining poplar (clone “I-214”) with Pseudomonas fluorescens and microbial consortia

The plant–microorganism combinations may contribute to the success of phytoextraction of heavy metal-polluted soil. The purpose of this study was to investigate the effects of cadmium (Cd) soil concentration on selected physiological parameters of the poplar clone “I-214” inoculated at root level with a strain (BT4) of Pseudomonas fluorescens and a commercial product based on microbial consortia (Micosat F Fito®). Plants were subjected to Cd treatment of 40 mg kg^?1 in greenhouse. The effects of plant–microbe interactions, plant growth, leaf physiology, and microbial activity were periodically monitored. Metal concentration and translocation factors in plant tissues proved enhanced Cd uptake in roots of plants inoculated with P. fluorescens and transfer to shoots in plants inoculated with Micosat F Fito®, suggesting a promising strategy for using microbes in support of Cd uptake. Plant–microbe integration increased total removal of Cd, without interfering with plant growth, while improving the photosynthetic capacity. Two major mechanisms of metal phytoextraction inducted by microbial inoculation may be suggested: improved Cd accumulation in roots inoculated with P. fluorescens, implying phytostabilization prospective and high Cd transfer to shoots of inoculated plants, outlining enhanced metal translocation.     

Leaching and persistence of ametryn and atrazine in red–yellow latosol

This study evaluated the mobility and persistence of atrazine and ametryn in red–yellow latosols using polyvinyl chloride columns with a diameter of 100 mm and a height of 15 cm. The assays simulated 60-mm rainfall events at 10-day intervals for 70 days. The persistence and leaching were evaluated for these two herbicides. The analytes obtained from the samples were quantified by gas chromatography using flame ionization detection. Compared with ametryn, atrazine showed a greater potential to reach depths below 15 cm over 30 days of simulated rain. Ametryn, however, showed greater persistence in soil at 70 days after application. The persistence of atrazine and ametryn in soil under sunlight was 10 and 144 days respectively. Atrazine was more susceptible to sunlight than ametryn because sunlight favored atrazine degradation in hydroxyatrazine. The results indicate that in red–yellow latosol, atrazine has a high leaching potential in short term, but that ametryn is more persistent and has a high leaching potential in long term.     

The need to implement an efficient biomass fractionation and full utilization based on the concept of “biorefinery” for a viable economic utilization of microalgae

In the present work, microalgae strains, such as Scenedesmus obliquus and Phaeodactylum tricornutum grown in indoor/outdoor photobioreactors (PBRs) and in open ponds (this is the first study on such strains cultivated in the local Southern Italy climatic conditions), were fully analyzed for their protein content, carbohydrates, lipids, and fatty acid profile in order to assess their potential use for the production of biofuels, chemicals, and omega-3, and as animal feed and human food. They are compared with Nannochloropsis sp. (commercial sample) which was fully analyzed in our laboratory and Chlorella (literature data). An economic evaluation was carried out, demonstrating that the cultivation of microalgae for the production of only biofuels will not match the economic standards. Conversely, if chemicals are also produced applying the biorefinery concept and using wastewater as a source of nutrients, it will be possible to have a good positive return from microalgae.     

Identification and assessment of ship emissions and their effects in the harbour of Göteborg,Sweden

The effect of ship emissions in the urban environment of Göteborg has been studied by multivariate analysis. The simultaneous measurements of relevant gases and sub-micron particles make identification of ship plumes possible. Increased concentrations of these species due to ship emissions are quantified for ships entering the inner part of the harbour. Annual depositions of SO₂ and NO₂ are estimated to be 220 and 115 kg km⁻² yr⁻¹, respectively. Exposure of transient particles (less than 0.1 μm in diameter) to this part of the harbour increased by a factor of 3 in number concentration when a ship plume was recorded. Ni, Pb, V and Zn are shown to have positive correlation with NO emissions from ships.     

In vitro effects of pollutants from particulate and volatile fractions of air samples—day and night variability

Chemicals in air were characterized for potential interference with signaling of estrogen, androgen, and arylhydrocarbon (AhR) receptors, which are known to play an important role in endocrine-disruptive changes in vivo. Previously, effects of this type have been studied mainly in particulate matter in the ambient air from various localities. In this study, both volatile and particulate fractions of air from three sites in Banja Luka region (Bosnia and Herzegovina) were investigated to describe the distribution of endocrine-disrupting contaminants on a small spatial scale. Circadian variability of air pollution was investigated by collecting samples during both day and night. Air samples collected from urban localities at night were more potent in producing the AhR-mediated effects than those collected during daytime. This trend was not observed at the reference rural location. None of the samples showed significant estrogenic or androgenic activity. On the other hand, anti-androgenicity was detected in both particulate and vapor phases, while anti-estrogenicity was detected only in the particulate fraction of air from all localities. The AhR-mediated potencies of samples were associated primarily with non-persistent compounds. Based on the concentrations of 28 individual compounds, PAHs accounted for approximately 30 % of the AhR-mediated potency determined by the bioassay. The results show that there can be a significant difference between levels of bioactive compounds in air between daytime and nighttime.     

Comparison of line– and point–source releases of tracer gases

Field measurements were made of greenhouse gas emissions from a wastewater treatment system using open path monitoring with detection by FTIR spectroscopy. Emission rates were determined by the ratio technique using a sulfur hexafluoride tracer gas released from a line source. As a quality control check, a second tracer gas – ethylene – was released from various single point locations. This paper presents a comparison of the line-source and point-source tracer releases for approximating emissions from the area source. The two types of tracer release showed excellent agreement when both release points were two hundred meters from the FTIR beam path. Data for other release points also were comparable, once differences in vertical dispersion as a function of distance are taken into account.