Pilot project of mechanical-biological treatment of waste in Brazil

By mechanical-biological treatment (MBT) of residual municipal solid waste the behaviour of landfills can be significantly improved. After MBT the organic content (COD and BOD5), total organic carbon, and total nitrogen in the leachate, as well as the gas production rate, are reduced to values lower than 90% of the fresh untreated waste. The volume of the stabilized material to be disposed on landfills decreases enormously, by up to 70%. The monitoring effort for a landfill constructed under these conditions is reduced to a minimum and the stabilized material can be used in other ways, as material for reforestation, for cover material or for thermal utilization to produce energy. Environmental conditions are important in MBT, as well as waste characteristics. This paper describes the results of a pilot project of MBT performed in Rio de Janeiro, Brazil. The results have shown that this technology can be used successfully in developing countries, with economy for the society and important results for the environment.     

Dynamic transformations of nitrogen during mechanical-biological pre-treatment of municipal solid waste

Mechanical-biological pre-treatment (MBP) of municipal solid waste (MSW) has gained evidence as a practice capable of accomplishing the requirements for environmental sustainable landfilling. In particular, MBP is effective in reducing the ammoniacal nitrogen content in the leachate. However, few data are available on the modifications of the nitrogen forms occurring during MBP and on the role played by processes such as nitrification and generation of refractory organic compounds. The dynamic transformations of nitrogen were investigated during the MBP. MSW was mechanically and biologically pre-treated; samples were collected at different stages of the process and analysed to investigate the evolution of nitrogen forms; batch and column leaching tests were performed as well. The results indicate that nitrification is negligible and volatilization can only partially explain the low ammoniacal nitrogen content in the leachate. Incorporation of ammoniacal nitrogen into a refractory organic form was assessed and is likely to play an important role. The maximum content of refractory organic nitrogen in the solid waste was achieved after about 60 days of aerobic pre-treatment; therefore, the minimal duration of the MBP should be about 8-9 weeks in order to optimize the ammoniacal nitrogen incorporation, unless the waste is characterized by a low C/N ratio.     

Influence of mechanical-biological waste pre-treatment methods on the gas formation in landfills

In order to minimise emissions and environmental impacts, only pre-treated waste should be disposed of. For the last six years, a series of continuous experiments has been conducted at the Institute WAR, TU Darmstadt, in order to determine the emissions from pre-treated waste. Different kinds of pre-treated waste were incubated in several reactors and various data, including production and composition of the gas and the leachate, were collected. In this paper, the interim results of gas production and the gas composition from different types of waste after a running time of six years are presented and discussed.     

Evaluation of compositional characteristics of organic waste shares in municipal solid waste in fast-growing metropolitan cities of India

Journal of Material Cycles and Waste Management - India currently has the second largest urban population worldwide, while facing an increasing burden on its urban solid waste infrastructure. To...     

Baseline levels of bioaerosols and volatile organic compounds around a municipal waste incinerator prior to the construction of a mechanical-biological treatment plant

New waste management programs are currently aimed at developing alternative treatment technologies such as mechanical–biological treatment (MBT) and composting plants. However, there is still a high uncertainty concerning the chemical and microbiological risks for human health, not only for workers of these facilities, but also for the population living in the neighborhood. A new MBT plant is planned to be constructed adjacently to a municipal solid waste incinerator (MSWI) in Tarragona (Catalonia, Spain). In order to evaluate its potential impact and to differentiate the impacts of MSWI from those of the MBT when the latter is operative, a pre-operational survey was initiated by determining the concentrations of 20 volatile organic compounds (VOCs) and bioaerosols (total bacteria, Gram-negative bacteria, fungi and Aspergillus fumigatus) in airborne samples around the MSWI. The results indicated that the current concentrations of bioaerosols (ranges: 382–3882, 18–790, 44–926, and <1–7 CFU/m³ for fungi at 25 °C, fungi at 37 °C, total bacteria, and Gram-negative bacteria, respectively) and VOCs (ranging from 0.9 to 121.2 μg/m³) are very low in comparison to reported levels in indoor and outdoor air in composting and MBT plants, as well in urban and industrial zones. With the exception of total bacteria, no correlations were observed between the environmental concentrations of biological agents and the direction/distance from the facility. However, total bacteria presented significantly higher levels downwind. Moreover, a non-significant increase of VOCs was detected in sites closer to the incinerator, which means that the MSWI could have a very minor impact on the surrounding environment.     

Immobilisation of PAH in waste materials

This paper gives an overview of the results of a research project into the possibilities of immobilising polycyclic aromatic hydrocarbons (PAH), that are present in waste materials. The results show that with hydraulic binders the waste materials can be solidified. The PAH do still leach to a relatively high extent. However, this PAH leaching can be decreased by more than a factor 10 by means of the addition of a specific additive. The immobilisation product fulfils technological requirements for the use as a road base construction material, such as compressive strength.     

有机物料对废碱锰电池的溶解作用研究

采用润湿好气-腐解培养法,研究有机物料对废碱锰电池的溶解作用,分析了培养时间对pH值,N,K,Zn和Mn溶出的影响。结果表明,稻草、鸡粪和鸽子粪处理培养过程中产生腐殖酸对废电池干粉均有溶解作用,其pH值明显降低;所有处理TN,Zn,Mn都呈现先增加后减小的趋势,15 d时溶量最大,以鸽子粪处理溶出较多;TK的溶出较慢,培养到10 d后才有溶出,均呈现逐渐增大的趋势;而TP溶出则规律性不强。     

对完善废旧物资税收政政策的意见和建议

废旧物资税收政策是关系到再生资源行业和企业生存与发展的重要问题,也是目前在保持经济可持续发展和建设节约型社会新形势下,政府机关主管部门和相关企业高度关注的一个重要问题.     

Use of selected waste materials in concrete mixes

A modern lifestyle, alongside the advancement of technology has led to an increase in the amount and type of waste being generated, leading to a waste disposal crisis. This study tackles the problem of the waste that is generated from construction fields, such as demolished concrete, glass, and plastic. In order to dispose of or at least reduce the accumulation of certain kinds of waste, it has been suggested to reuse some of these waste materials to substitute a percentage of the primary materials used in the ordinary portland cement concrete (OPC). The waste materials considered to be recycled in this study consist of glass, plastics, and demolished concrete. Such recycling not only helps conserve natural resources, but also helps solve a growing waste disposal crisis. Ground plastics and glass were used to replace up to 20% of fine aggregates in concrete mixes, while crushed concrete was used to replace up to 20% of coarse aggregates. To evaluate these replacements on the properties of the OPC mixes, a number of laboratory tests were carried out. These tests included workability, unit weight, compressive strength, flexural strength, and indirect tensile strength (splitting). The main findings of this investigation revealed that the three types of waste materials could be reused successfully as partial substitutes for sand or coarse aggregates in concrete mixtures.     

Leaching behaviour of waste and stabilized waste materials; characterization for environmental assessment purposes

The importance of systematic trends in trace contaminant leaching from waste materials and stabilized waste is stressed. Similarities in leaching behaviour of different waste materials and mechanisms for leaching from stabilized waste forms are identified. The use of diffusion measurements to quantify the mobility of specific chemical species in waste and soil is discussed. Implementation of more fundamental regulatory testing procedures which reflect the behaviour of materials in end use applications, is recommended to allow better control over environmental impact in the wide variety of utilization and disposal practices.     

Biodegradable packing materials from hydrolysates of collagen waste proteins

Enzymatic hydrolysates of waste collagen proteins (H), from current industrial manufacture (leather, edible meat product casings, etc.) of mean molecular mass 20-30 kDa by a reaction with dialdehyde starch (DAS), produces hydrogels applicable as biodegradable (or even edible) packaging materials for food, cosmetic and pharmaceutical products. Thermo-reversibility of prepared hydrogels is given by concentrations of H and DAS in a reaction mixture. At concentrations of H 25-30% (w/w) and that of DAS 15-20% (related to weight of hydrolysate), thermo-reversible hydrogels arise, which can be processed into packaging materials by a technique similar to that of soft gelatin capsules (SGC). Exceeding the limit of 20% DAS leads to hydrogels that are thermo-reversible only in part, a further increase in DAS concentration then leads to thermo-irreversible gels whose processing into biodegradable packaging materials necessitates employment of other procedures.     

金属冶炼进口物料的固体废物鉴别方法

建立了金属冶炼进口物料的固体废物鉴别方法,并利用该方法对海关查扣的3种金属冶炼进口物料进行了固体废物鉴别。鉴别结果显示:物料1、2和3的自然属性分别为砷含量超标铜精矿、锰阳极泥、回转窑氧化锌,产生来源分别为有害物质超标的产品、污染控制设施产生的物质、有意识加工的目标产物;物料1和2属于我国禁止进口的固体废物,物料3不属于固体废物。本文建立的固体废物鉴别方法可行,可为金属冶炼进口物料的固体废物鉴别和监管提供参考。     

Recovery of valuable materials from waste liquid crystal display panel

Associated with the rapid development of the information and electronic industry, liquid crystal displays (LCDs) have been increasingly sold as displays. However, during the discarding at their end-of-life stage, significant environmental hazards, impacts on health and a loss of resources may occur, if the scraps are not managed in an appropriate way. In order to improve the efficiency of the recovery of valuable materials from waste LCDs panel in an environmentally sound manner, this study presents a combined recycling technology process on the basis of manual dismantling and chemical treatment of LCDs. Three key processes of this technology have been studied, including the separation of LCD polarizing film by thermal shock method the removal of liquid crystals between the glass substrates by the ultrasonic cleaning, and the recovery of indium metal from glass by dissolution. The results show that valuable materials (e.g. indium) and harmful substances (e.g. liquid crystals) could be efficiently recovered or separated through above-mentioned combined technology. The optimal conditions are: (1) the peak temperature of thermal shock to separate polarizing film, ranges from 230 to 240 °C, where pyrolysis could be avoided; (2) the ultrasonic-assisted cleaning was most efficient at a frequency of 40 KHz (P = 40 W) and the exposure of the substrate to industrial detergents for 10 min; and (3) indium separation from glass in a mix of concentrated hydrochloric acid at 38% and nitric acid at 69% (HCl:HNO₃:H₂O = 45:5:50, volume ratio). The indium separation process was conducted with an exposure time of 30 min at a constant temperature of 60 °C.     

Modification of hydraulic conductivity in granular soils using waste materials

This paper evaluates the use of waste products such as silica fume and fly ash in modification of the granular soils in order to remove some environmental problems and create new useful findings in the field of engineering. It is known that silica fume and fly ash, as well as clay material, are used in geotechnical engineering because of their pozzolanic reactivity and fineness to improve the soil properties needed with respect to engineering purposes. The main objective of this research project was to investigate the use of these materials in geotechnical engineering and to improve the hydraulic properties of soils by means of grouting. For this reason, firstly, suitable grouts in suspension forms were prepared by using silica fume, fly ash, clay and cement in different percentages. The properties of these cement-based grouts were then determined to obtain the desired optimum values for grouting. After that, these grouts were penetrated into the soil samples under pressure. The experimental work indicates that these waste materials and clay improved the physical properties and the fluidity of the cement-based grouts and they also decreased the hydraulic conductivity of the grouted soil samples by sealing the voids of the soil. The results of this study have important findings concerning the use of these materials in soil treatment and the improvement of hydraulic conductivity of the soils.     

Enzymatic hydrolysis of organic waste materials in a solid-liquid system

In the current climate of increasing emphasis on environmental protection and efficient waste management, regional management bodies and environmental agencies are striving to achieve an economical and environmentally acceptable system for the recycling of biodegradable organic wastes. Composting would appear to be a cost effective solution to this problem, but in its entirety, composting is an inherently lengthy and variable process and is restrictive in terms of the demand on resources and space in composting plants. The aim of this study was to compare a biological composting process of solid residues with an enzymatic hydrolysis process of residues. The length of time required to naturally compost three organic materials, spent mushroom compost (SMC), farmyard manure (FYM) and dairy wastewater sludge (DWS) under optimal conditions was 42 days, 98 days and 84 days, respectively. In an attempt to accelerate this process, commercial enzymes were added to the waste products in a heterogeneous solid-liquid system. The enzymes utilised included a range of proteases, cellulases, ligninases, lipases and pectinases, which are responsible for the hydrolysis of protein, cellulose, lignin, lipids and carbohydrates, respectively. Preliminary results indicate that all of the organic materials were stabilised within 9h and that the enzymes used would, therefore, improve the efficiency of a waste management plant, if such a system were employed. Spent mushroom compost has a mean N/P/K ratio of 20:10:10 recorded for composted SMC, while a similar ratio of 20:10:20 was obtained for hydrolysed SMC. In contrast, composted farmyard manure has a N/P/K ratio of 30:0:30 and a ratio of 10:1:10 for hydrolysed FYM. Finally, composted DWS has a N/P/K ratio of 20:1:30 while DWS hydrolysate has a N/P/K ratio of 40:1:20, with the decrease in nitrogen in the composted DWS attributed to the addition of wood chippings and sawdust as a bulking agent. While all three materials have a considerable supply of plant nutrients, the variability in nutrients could be overlooked when employed as a soil amendment.     

Effect of organic compositions of aerobically pretreated municipal solid waste on non-methane organic compound emissions during anaerobic degradation

Odor pollution caused by municipal solid waste (MSW) treatment plants has become a growing public concern. Although aerobic pretreatment of MSW has advantages in accelerating landfill stabilization, the property of non-methane organic compound (NMOC) emissions from aerobically pretreated MSW (APMSW) during landfilling is unknown. To investigate NMOC emissions from anaerobic degradation of APMSW and to study the impact of organic compositions of APMSW and their decomposition stages, five simulative anaerobic bioreactors (R1-R5) were filled up with APMSW of different original organic compositions in a laboratory. For NMOC analysis, samples were collected from the gas that accumulated separately during two successive independent stages of the whole experiment. The results showed that the cumulative quantities of NMOCs from R1 to R5 were 1.11, 0.30, 0.18, 0.28, and 0.31 mg/kg DM, respectively, when volatile solid was degraded by 34.8-47.2%. As the organic content of the original waste was lower, the proportion of NMOCs generated in the early stage of anaerobic degradation became higher. Multiple linear regression analyses of the relationship between the quantities of degraded organics and generated NMOCs showed that lipid and protein have a strong effect on NMOC amount. The effect of lipid on NMOC quantity lasts longer than that of protein. This observation suggests that controlling the lipid and protein contents in MSW can reduce the odor from landfills.     

Use of mix of clay/solid waste from steel works for civil construction materials.

The present study focuses on the use of solid waste generated by the steel works in Brazil for manufacturing clay-based structural products. The waste sample was characterized regarding chemical composition, X-ray diffraction, particle size, morphology, specific surface and plastic properties. The waste was added in gradual proportions to a kaolinitic clay from zero up to 3 wt.%. Ceramic bodies were formed by vacuum extrusion and fired at 950 degrees C. The physical-mechanical properties (linear shrinkage, water absorption, apparent density and flexural strength) of the resulting clay/solid waste mixtures were determined. In addition, leaching tests were performed according Brazilian Standards as well as a preliminary analysis of gases evolved during the thermal process. It was found that the solid waste is formed by irregular particles, ranging in size from 1 to 500 microm. The test results indicate that solid wastes generated by steel works can be used as filler in construction materials, thereby increasing reuse in an environmentally safe manner.     

Foamed lightweight materials made from mixed scrap metal waste powder and sewage sludge ash.

The porous properties and pozzolanic effects of sewage sludge ash (SSA) make it possible to produce lightweight materials. This study explored the effects of different metallic foaming agents, made from waste aluminium products, on the foaming behaviours and engineering characteristics, as well as the microstructure of sewage sludge ash foamed lightweight materials. The results indicated that aluminium powder and mixed scrap metal waste powder possessed similar chemical compositions. After proper pre-treatment, waste aluminium products proved to be ideal substitutes for metallic foaming agents. Increasing the amount of mixed scrap metal waste by 10-15% compared with aluminium powder would produce a similar foaming ratio and compressive strength. The reaction of the metallic foaming agents mainly produced pores larger than 10 microm, different from the hydration reaction of cement that produced pores smaller than 1 microm mostly. To meet the requirements of the lightweight materials characteristics and the compressive strength, the amount of SSA could be up to 60-80% of the total solids. An adequate amount of aluminium powder is 0.5-0.9% of the total solids. Increasing the fineness of the mixed scrap metal waste powder could effectively reduce the amount required and improve the foaming ratio.