纳米Al13的分离方法及混凝效果动态过程的研究

以相同Al13含量、不同浓度的PAC为原料,利用乙醇-丙酮混合溶剂法、SO4^2-／Ba^2 沉淀置换法以及柱层析法分离提纯纳米Al13形态,同时利用Al-Ferron逐时络合比色法、^27Al-NMR等多种现代分析手段进行分析鉴定,比较其分离效果,并采用烧杯实验法和透光率脉动检测技术对Al13形态以及PAC、AlCl3的絮凝效果及絮凝过程中絮集物形成和增长的变化差异作了对比性研究．实验结果表明,乙醇．丙酮混合溶剂法对Al13分离纯化效果最好,分离所得Al13平均粒径大,聚合程度高．柱层析法受柱体积的影响只对低浓度的PAC有较好的分离效果;SO4^2-／Ba^2 沉淀置换法虽具有较好的分离效果,但分离过程有其他杂质离子的加入,影响到产品品质．混凝效果和动态实验结果表明,Al13形态是在絮凝过程中起电中和作用的主要形态,具有较强的除浊及脱色能力,在混凝过程中当絮体受到剪切力的破坏时Al13形态比PAC和AlCl3具有更强重新絮凝的能力．     

Removal natural organic matter in typical south-China source water during enhanced coagulation of a with IPF-PACl

Systematic investigation on enhancing removal of natural organic matter （NOM） using inorganic polymer flocculant （IPF）, polyaluminum chloride（PACI） and polyacrylamide（PAM） was performed in a typical south-China source water. Enhanced coagulation and applying polymer flocculant-aid were compared through jar tests and pilot tests. Raw water and settled water were characterized and fractionated by resin adsorption. The results show that DOC composes major part of TOC. The DOC distribution keeps relatively stable all around the year with typical high amounts of the hydrophilic matter around 50%. The distribution between HoB, HoA and HoN varies and undergoes fluctuation with the year round. During the summer season, the HoN becomes gradually the major part in hydrophobic parts. PACI with the species being tailor-made shows little pH effect during coagulation. The enhanced coagulation dosage for PACI could be 4.5 mg/L for the typical source water. The highest TOC removal achieved 31%. To be economically, 3 mg/L dose is the optimum dosage. Although hydrophilic fractions of NOM of both treatment strategies are removed about 30%, NOM causing UV254 absorbance were well removed（about 90%）. Hydrophobic bases and acids fractions are much more removed under enhanced conditions. The hydrophilic fraction could be better removed using PAM, the polymer coagulant aid.     

Disinfection byproduct precursor removal by enhanced coagulation and their distribution in chemical fractions

Raw water from the Songhua River was treated by four types of coagulants, ferric chloride(FeCl3), aluminum sulfate(Al2(SO4)3),polyaluminum chloride(PACl) and composite polyaluminum(HPAC), in order to remove dissolved organic matter(DOM). Considering the disinfection byproduct(DBP) precursor treatability, DOM was divided into five chemical fractions based on resin adsorption.Trihalomethane formation potential(THMFP) and haloacetic acid formation potential(HAAFP) were measured for each fraction. The results showed that hydrophobic acids(HoA), hydrophilic matter(HiM) and hydrophobic neutral(HoN) were the dominant fractions.Although both HoN and HoA were the main THM precursors, the contribution for THMFP changed after coagulation. Additionally,HoA and HiM were the main HAA precursors, while the contribution of HoN to HAAFP significantly increased after coagulation.HoM was more easily removed than HiM, no matter which coagulant was used, especially under enhanced coagulation conditions.DOC removal was highest for enhanced coagulation using FeCl3 while DBPFP was lowest using PACl. This could indicate that not all DOC fractions contained the precursors of DBPs. Reduction of THMFP and HAAFP by PACl under enhanced coagulation could reach51% and 59% respectively.     

城市景观水体混凝除藻过程对氮元素协同去除特性初探

以城市景观水体净化为目标,考察混凝除藻同时去除氮元素的特性和影响因素. 结果发现,水体内较高的DOC(溶解性有机质)含量会阻碍藻浊度的去除. 聚合氯化铝(PACl)以及PACl与硫酸铝(Alum)的复合剂(PACl+Alum)对藻浊度的去除效果均相对单独使用PACl或Alum较好,其中PACl+Alum对其他物质(如氮、DOC等)的去除效果也相对单独使用PACl或Alum更佳;在同样的最佳投药量时,低pH条件能获得更好的藻浊度去除率;对氮元素去除的进一步研究发现,DON(溶解性有机氮)的去除特征和过程与TN(总氮)非常一致,表明该水体TN的去除主体上是通过DON的去除实现的;低pH条件同样有利于氮和DOC的去除;但DOC与DON去除的不同步性,说明DOC中的DON成分和性质是非均一性的,是未来可进一步深入研究的重要方向.      

混凝沉淀-UF工艺去除二级出水中ARGs效能研究

为了研究混凝沉淀-UF工艺对城市污水处理厂二级出水中ARGs（抗生素抗性基因）去除的影响,以PACl（聚合氯化铝）和PFS（聚合硫酸铁）作为混凝剂,采用qPCR（实时荧光定量聚合酶链式反应）和EEM（三维荧光光谱）等分析混凝沉淀-UF工艺对ARGs的削减及其影响因素.结果表明:① PACl、PFS投加量（分别以Al、Fe计,下同）分别为0.85、0.50 mmol/L时,与直接UF工艺相比,混凝沉淀-UF工艺对水中各类ARGs的去除量高2~3个数量级,其中PACl-UF工艺的效果更好,去除量为2.51~3.52个数量级;对水中DOC（溶解性有机碳）、富里酸类及溶解性微生物代谢产物的去除效果更好,DOC去除率由18%升至36%.②直接UF、PACl-UF、PFS-UF 3种工艺膜进、出水的线性拟合结果显示,ARGs浓度与ρ（DOC）、16S rDNA浓度均呈显著正相关.研究显示,混凝沉淀-UF工艺可以有效去除二级出水中的ARGs,且有机物、16S rDNA的去除有助于ARGs的削减.      

Effects of pre-ozonation on organic matter removal by coagulation with IPF-PACI

Ozone plays an important role as a disinfectant and oxidant in potable water treatment practice and is increasingly being used as a pre-oxidant before coagulation. The purpose of this study is to obtain insight into the mechanisms that are operative in pre-ozonized coagulation. Effects ofpre-ozonation on organic matter removal during coagulation with IPF-PAC1 were investigated by using PDA （photometric disperse analysis）, apparent molecular weight distribution and chemical fractionation. The dynamic formation of flocs during coagulation process was detected. Changes of aquatic organic matter （AOM） structure resulted from the influence of pre-ozonation were evaluated. Results show that dosage of O3 and characteristics of AOM are two of the major factors influencing the performance of O3 on coagulation. No significant coagulation-aid effect of O3 was observed for all experiments using either A1C13 or PAC1. On the contrary, with the application of pre-ozonation, the coagulation efficiency of A1C13 was significantly deteriorated, reflected by the retardation of floc formation, and the removal decreases of turbidity, DOC, and UV254. However, if PACl was used instead of AlCl3, the adverse effects of pre-ozonation were mitigated obviously, particularly when the O3 dosage was less than 0.69 （mg O3/mg TOC）. The difference between removals of UV254, and DOC indicated that pre-ozonation greatly changed the molecular structure of AOM, but its capability of mineralization was not remarkable. Only 5% or so DOC was removed by pre-ozonation at 0.6--0.8 mg/L alone. Fractionation results showed that the organic products of pre-ozonation exhibited lower molecular weight and more hydrophilicity, which impaired the removal of DOC in the following coagulation process.     

Al13形态在混凝中的作用机制

从铝的水解形态转化角度考察了铝盐在高碱度和高有机物浓度水体中的混凝行为.结果表明,铝盐的混凝效能是与混凝过程中的Al₁₃含量成正比.高投药量时氯化铝(AlCl₃)既可以有效调节水体pH值又能在混凝过程中原位水解产生较多的Al₁₃形态,因而混凝效能要高于聚合氯化铝(PACl).在铝盐混凝中,调节pH值到6～7之间可以控制铝形态分布从而达到提高混凝效能和减少残留铝的目的.在调节pH值强化混凝的方法中使用传统铝盐的效果要好于无机高分子絮凝剂.     

Preparation and characterization of organic polymer modified composite polyaluminum chloride

Compared with traditional aluminum salts, polyaluminum chloride （PACI） has better coagulation-flocculation performance in turbidity removal. However, it is still inferior to organic polymers in terms of bridging function. In order to improve the aggregating property of PACl, different composite PACl flocculants were prepared with various organic polymers. The effect of organic polymer on the distribution or Al（Ⅲ） species in composite flocculants was studied using ^27TAl NMR and Al-ferron complexation methods. The charge neutralization and surface adsorption characteristics of composite flocculants were also investigated. Jar tests were conducted to evaluate the turbidity removal efficacy of organic polymer modified composite flocculants. The study shows that cationic polymer and anionic polymer have significant influences on the coagulation-flocculation behaviors of PACl. Both cationic and anionic polymers can improve the turbidity removal performancc of PACl but the mechanisms arc much different： cationic organic polymer mainly increases the charge neutralization ability, but anionic polymer mainly enhances the bridging function.     

Effect of in-situ formed Al hydrates through long-term aging on enhanced particle destabilization by PACl coagulation

Aging of polyaluminum chloride (PACl) coagulants could significantly influence hydrolyzed Al speciation ruling coagulation performance. The goal of this study was to investigate Al species transformation through long-term aging and its impact on coagulation performance. Two kinds of commercial coagulants (PACl-1 and PACl-2) were stored for in-situ aging tests in six months to evaluate Al species variation with time and the performance of coagulation with natural turbid waters. The results showed that CaSO₄ precipitation easily occur in a commercial PACl coagulant with time as it contains SO₄^2? and Ca²⁺. It also activates the precipitation of gibbsite Al(OH)₃ in PACl with aging. Through 180 days aging, both monomeric Al (Al_a) and polymeric Al (Al_b) substantially transform into colloidal Al (Al_c) and precipitated for both PACl coagulants. At low turbidity (10 NTU), PACl-1 has a superior turbidity reduction rate than PACl-2, while PACl-2 performs a little better turbidity reduction at high turbidity (1000 NTU) regardless of aging time. With aging time, an obvious decrease in turbidity reduction for PACl-1 coagulation is observed at low turbidity of 10 NTU, while the improvement in turbidity reduction for PACl-2 coagulation by enhanced sweep flocculation can be achieved as Al_b mostly transform into Al_c after 150 days aging. It is concluded that dominant in-situ formed Al_c after a long time hydrolysis can improve PACl coagulation efficiency in turbidity reduction by enhanced sweep flocculation, especially for low turbidity water, but the increase in preformed Al_c in PACl would worsen particle destabilization after aging.     

Drinking water treatment using a submerged internal-circulation membrane coagulation reactor coupled with permanganate oxidation

A submerged internal circulating membrane coagulation reactor(MCR) was used to treat surface water to produce drinking water. Polyaluminum chloride(PACl) was used as coagulant,and a hydrophilic polyvinylidene fluoride(PVDF) submerged hollow fiber microfiltration membrane was employed. The influences of trans-membrane pressure(TMP), zeta potential(ZP) of the suspended particles in raw water, and KMnO_4 dosing on water flux and the removal of turbidity and organic matter were systematically investigated. Continuous bench-scale experiments showed that the permeate quality of the MCR satisfied the requirement for a centralized water supply, according to the Standards for Drinking Water Quality of China(GB 5749-2006), as evaluated by turbidity(1 NTU) and total organic carbon(TOC)(5 mg/L)measurements. Besides water flux, the removal of turbidity, TOC and dissolved organic carbon(DOC) in the raw water also increased with increasing TMP in the range of 0.01–0.05 MPa. High ZP induced by PACl, such as 5–9 mV, led to an increase in the number of fine and total particles in the MCR, and consequently caused serious membrane fouling and high permeate turbidity.However, the removal of TOC and DOC increased with increasing ZP. A slightly positive ZP, such as 1–2 mV, corresponding to charge neutralization coagulation, was favorable for membrane fouling control. Moreover, dosing with KMnO_4 could further improve the removal of turbidity and DOC, thereby mitigating membrane fouling. The results are helpful for the application of the MCR in producing drinking water and also beneficial to the research and application of other coagulation and membrane separation hybrid processes.     

Al(Ⅲ) speciation distribution and transformation in high concentration PACl solutions

Effects of Al(Ⅲ) concentration and pH on the speciation of Al(Ⅲ) in polyaluminum chloride (PACl) solutions especially on the Al13 fraction were investigated. A series of PACl samples were prepared over the range of Al(Ⅲ) concentration from 0.01 to 2.0 mol/L with the B (OH/Al ratio) value from 1.0 to 2.5 by forced hydrolysis of AlCl3. The samples were characterized by ferron assay,pH and 27Al NMR. It was shown that the Al(Ⅲ) concentration had a dramatic effect on the hydrolysis processes and the species distribution of PACl was in relate to the decrease of pH. The fraction of Al species, Alb (or Al13) decreased and Alc increased with increase of total Al(Ⅲ) concentration. Under the condition of Al(Ⅲ) 2.0 mol/L, B = 2.5, the pH value was 2.73 and no Al13 could be detected. During diluting and aging, the species distribution evolved. The Al13 could then be detected again and the amounts increased with time. If the diluted samples were concentrated by freeze dry at -35℃ or heating at 80℃, the pH value and Al13 content would decrease with the increased concentration. It demonstrated that the key factor for formation of Al13 in concentrated PACl was pH value.     

Al(Ⅲ) speciation distribution and transformation in high concentration PACl solutions

Effects of Al（Ⅲ） concentration and pH on the speciation of Al（Ⅲ） in polyaluminum chloride （PACl） solutions especially on the Al13 fraction were investigated. A series of PACl samples were prepared over the range of Al（Ⅲ） concentration from 0.01 to 2.0 mol/L with the B （OH/Al ratio） value from 1.0 to 2.5 by forced hydrolysis of AICl3. The samples were characterized by ferron assay, pH and 27^Al NMR. It was shown that the Al（Ⅲ） concentration had a dramatic effect on the hydrolysis processes and the species distribution of PACl was in relate to the decrease of pH. The fraction of Al species, Alb （or Al13） decreased and Al0 increased with increase of total Al（Ⅲ） concentration. Under the condition of Al（Ⅲ） 2.0 reel/L, B = 2.5, the pH value was 2.73 and no Al13 could be detected. During diluting and aging, the species distribution evoIved. The Al13 could then be detected again and the amounts increased with time. If the diluted samples were concentrated by freeze dry at -35℃ or heating at 80℃, the pH value and Al13 content would decrease with the increased concentration. It demonstrated that the key factor for formation of Al13 in concentrated PACl was pH value.     

臭氧对有机物混凝的影响

采用PDA(Photometric Disperse Analysis)和有机物表观分子量分级、有机物化学极性分级技术从絮体形成过程、絮体表现、有机物分子水平变化等方面研究了臭氧预氧化对混凝过程的影响;并对比了不同混凝剂在预臭氧条件下的混凝过程和效率.结果表明:臭氧预氧化对混凝过程有复杂的影响,其剂量和水体有机物特征决定了其对混凝的整体影响效果.有机物分级显示,臭氧化对有机物结构有重要影响,导致有机物极性、亲水性组分含量大幅提高(36.7%),小分子量组分(<10×10³)大幅增高(100%左右);但总的DOC去除率不高(3.28%).对PACl而言,在中、低剂量(O₃/TOC<0.7)下,臭氧对絮体形成过程影响较小,但对絮体沉降性和浊度去除已经有阻碍作用.在中、高剂量下(O₃/TOC>0.7),对絮体形成有显著滞后,浊度、有机物去除效率下降.AlCl₃对臭氧化作用反应敏感,臭氧化在试验剂量条件下,对絮体形成和浊度、有机物去除都有明显的阻碍作用.     

Interaction of PACls with sulfate

IntroductionPolyaluminumchloride (PACl)asamainkindofinorganicpolymerflocculantsisanewhighereffectivewaterandwastewatertreatmentreagent.Basedonthetraditionallow molecularaluminum ,ithasbeendevelopedworldwidesincethe 196 0s(Tang,1994 ;1990 ;1987) .PAClistheintermediateproductofthehydrolysis polymerization ageingprocessofAl(III)undersuitableconditions.Atpresent,itisgenerallyknownthattherearemanypossiblespeciesexistintheAl(III)solution ,suchasmonomers,oligomers,Al13 [AlO4Al12 (OH) 2 4(H2 …     

PACl-Al30絮凝剂研究现状和展望

具30个铝原子的Al30是继Al13之后新发现的一种高铝聚合形态,与Al13类似,具Keggin结构,也被认为是聚合氯化铝(PACl)中的新型优势混凝形态。文章从PACl发展的视角,对Al30形态的合成、鉴定以及混凝作用进行了综述,并就高Al30的合成、新型Al30复合硅絮凝剂的开发以及其表征和混凝机理研究等三个方面作出了有关展望。     

不同铝聚合形态对聚合铝混凝效果的影响

通过氯化铝(铝单体或初聚物形态Ala)、高Alb含量聚合铝(中等聚合形态Alb)、高Alc含量聚合铝(铝溶胶等高聚合形态Alc)和工业PACl(不同聚合度铝的混合形态Alabc)对某水厂沉后水实际水样进行烧杯混凝实验,依据絮体生长状况、浊度、UV254、颗粒数和过滤指数等参数综合评价不同铝形态的混凝作用效果,从而得出铝的最佳混凝形态.结果表明,高Alb含量聚合铝对浊度去除较好;而高Alc含量聚合铝对于颗粒物和UV254的去除效果较佳.     

Application of a green coagulant with PACl in efficient purification of turbid water and its mechanism study

The applications of natural polymeric flocculants due to their green feature has been recently received much more attention. In this work, the combined usages of a cationic starch-based coagulant and polyaluminum chloride (PACl) were extensively evaluated for various addition sequences in the coagulation of both raw (surface water from the Jiuxiang River) and synthetic turbid water (two kaolin suspensions with different initial turbidities). Two typical cationic starch-based coagulants with different structures (St-G and St-E) were tried. In comparison to St-G, St-E and PACl used individually as well as St-G and St-E dosed after PACl, the combination of the starch-based coagulants fed before PACl showed higher turbidity removal efficiency, which featured not only less optimal doses of both inorganic and organic coagulants but also lower residual turbidity. On the basis of a detailed analysis of the particle size and its distribution in solution supernatants before and after coagulation by two starch-based coagulants and PACl, polymeric coagulants preferentially coagulate the small-sized colloids due to their distinct long-chain structures, but PACl preferentially coagulates the medium-sized ones. Thus, the medium-sized particles that were previously formed by the starch-based coagulants would be collectively and effectively removed by the subsequent addition of PACl. The addition sequence of the inorganic and organic coagulants in their combined usage is an important factor for improvement of the turbidity removal efficiency in practice.     

Fractionation of residual Al in natural water treatment from reservoir with poly-aluminum-silicate-chloride (PASiC): Effect of OH/Al, Si/Al molar ratios and initial pH

An aluminum fractionation study was conducted for a surface reservoir water treatment to understand the performance of poly-aluminum-silicate-chloride (PASiC) in terms of the residual Al fractions as a function of initial pH. The coagulation performance expressed as turbidity and organic matter removal was established as supporting data. Some extra data were evaluated in terms of the residual Al ratio of the composite PASiC coagulant. The main residual Al sources were the Al fractions derived from the use of PASiC. The turbidity and organic matter removal ability was optimal at initial pH 6.00-7.00, while the concentrations of various residual Al species and the residual Al ratio of PASiC were minimal at an initial pH range of 7.00-8.00. Under the conditions of OH/Al molar ratio = 2.00 and Si/Al molar ratio = 0.05, PASiC had superior coagulation performance and comparatively low residual Al concentrations. The Al fraction in the composite PASiC coagulant seldom remained under such conditions. Experimental data also indicated that the suspended (filterable) Al fraction was the dominant species, and organic-bound or organo-Al complex Al was considered to be the major species of dissolved Al in water treated by PASiC coagulation. Additionally, the dissolved inorganic monomeric Al species dominated the dissolved monomeric Al fraction.     

不同水体溶解性有机物的混凝去除特性

采用硫酸铝、工业氯化铁、无机高分子絮凝剂(PAC)3种无机混凝剂,对广州珠江、北京密云、天津滦河不同原水进行了混凝实验,分析了不同混凝剂去除水体有机物的特性以及不同水体溶解性有机物(DOM)的内在分级特征与其混凝去除率的关系.实验结果表明,①珠江水体由于碱度低,pH较易下降,高投药浓度下此水体DOM更易被氯化铁去除;中低投药下,在南方水体中,PAC与盐类絮凝剂对去除DOM的混凝性能差别不如在北方水体中明显,表明南北方水体DOM的内在特性存在一定差异,即北方水体DOM中可混凝去除部分的有机物易发生电中和作用,带有较多负电基团,南方珠江水体DOM含带电基团的有机物相对较少,而中性有机物含量相对较高,这与进一步分级结果一致.②所有水体从混凝收敛点看,总溶解性有机碳(DOC)去除率都是工业PAC最高,显示电中和(憎水化)-沉淀(吸附)可能为这些水体DOM的主要去除机理.③从不同水体的DOC平均去除率看,珠江水体高于密云水体,它们又明显高于滦河水体.对水体DOM进一步的化学分级研究结果表明,DOC去除率越高的水体,其中的憎水中性物质(HoN)含量也越高.这表明,除了碱度、总有机碳(TOC)外,原水DOM的内在化学分级特征也是影响水体DOC混凝去除率的重要因素.     

混凝-吸附处理黄河水及对氯消毒中氯衰减的影响

选用2种无机高分子混凝剂聚合氯化铁(PFC)和聚合氯化铝(PAC)处理黄河水,考察了混凝剂的投加量对浊度、UV254、DOC和高锰酸盐指数的去除效果,并结合混凝出水的Zeta电位分析其混凝机制.选择粉末活性炭与混凝联用,研究了混凝剂和吸附剂投加量以及二者的投加顺序对有机物去除效果的影响,并对混凝吸附后出水进行加氯消毒,考察水中残余氯随时间的变化.结果表明,2种混凝剂均有较高的浊度去除率(﹥90%).PAC对UV254、高锰酸盐指数和DOC的去除率分别为29.2%、26.1%和27.9%;PFC对三者的去除率分别为32.3%、23.3%和32.9%.PAC在混凝过程中,电中和作用占主导地位;PFC在混凝过程中,吸附架桥和电中和同时发挥作用.混凝-吸附联用处理黄河水样时,有机物的去除率随混凝剂和吸附剂投加量的增加而升高.先混凝后吸附工艺对UV254和DOC的去除效果优于先吸附后混凝工艺.先使用PAC混凝后吸附对UV254和DOC的去除率分别为95.2%和99.9%;对于PFC,先混凝后吸附对UV254和DOC的去除率分别为90.1%和99.9%.但是先投加粉末活性炭能提高矾花的沉降性能,且处理出水在保持持续消毒效果方面优于前者.