污泥烧结制植物栽培基质技术及应用研究

为实现污泥的无害化处理和资源化利用,本研究对污泥进行初步脱水和干化深度脱水,使含水率降到30%左右,干化后的污泥进行焚烧处理,在脱水滤液中加入Mg盐回收氮磷得到鸟粪石。结果显示:脱水滤液中调节镁/磷摩尔比为1.0～1.2时,可得到较多鸟粪石沉淀;烧结温度为900～1100℃,烧结时间为20～40min时,可得到环保性能优良的烧结体,将鸟粪石和污泥烧结体混合得到可用于园林绿化的植物栽培基质。     

酸改性污泥基复合陶粒对Pb2+的吸附性能研究

以污泥、磷尾矿和赤泥为原料制备陶粒,用盐酸、硝酸和柠檬酸进行改性,研究陶粒对水中Pb2+的吸附效果,并通过扫描电镜（SEM）、表面基团、零电荷点（pHPZC）和傅里叶红外光谱（FTIR）分析陶粒对Pb2+的吸附机理。结果表明,低浓度盐酸或硝酸改性陶粒对Pb2+的去除率更好,柠檬酸改性陶粒对Pb2+的去除率低于未改性陶粒。酸改性陶粒具有比表面积大、孔隙结构发达、酸性基团含量多、等电点低等特点,对Pb2+的吸附同时存在物理吸附和化学吸附过程,可用作含Pb2+废水的处理材料。     

回流污泥比对厌氧释磷效果影响研究

为系统研究厌氧污泥回流比对生物除磷效果的影响,本文以实际生活污水作为研究水样,研究不同污泥回流比下厌氧段对COD、N、P的去除效果,深入研究污泥回流比对生物强化除磷代谢过程的影响。结果表明,在厌氧环境中污泥回流比对NH3-N的去除没有明显影响,但对硝态氮、TP、COD的去除影响较大。最佳回流污泥比应控制在60%~80%左右,在这两个工况下,PAO释磷量能达到24.13mg/L,这样能使PAO在厌氧池有效地利用碳源,充分释磷,从而提高除磷效率,同时应控制最佳厌氧有效时间为2~3h,如果厌氧时间过长或者过短都对PAO释磷产生一定的负作用。     

A2/O工艺脱氮除磷运行效果分析

采用统计学方法对新疆某污水处理厂A2/O工艺进行进水水质数据分析,发现数据存在严重自相关现象,运用主成分消除法和岭回归消除法以消除自相关性。结果表明：TN和TP是污水厂提标改造的关键;碳源匮乏和缺氧区存在溶解氧(DO)是TN去除不佳的主要原因;适当提高污泥浓度(MLSS)和水力停留时间(HRT)是强化TP去除的措施;温度是影响脱氮除磷的主要因素。将温度模型与自相关磷模型相结合,可提高磷模型精度,有利于出水TP的预测。降低DO、增加外碳源,控制MLSS为3 500 mg/L~4 500 mg/L、HRT为5.4 h~8.0 h、厌氧区和好氧区DO为0.3 mg/L和2 mg/L、污泥龄（SRT）为11 d~12 d,可提升工艺脱氮除磷效果。     

钢铁企业烧结工段SO_2监测的主要影响因素及解决方案

针对钢铁企业烧结工段烟气的特点,对可能影响碘量法、定电位电解法SO_2监测结果的因素进行分析,并提出相应的对策。研究表明:定电位电解法受CO干扰较大,根据数学模型修正后,可进行SO_2浓度的快速估算;碘量法受吸收液温度、分析时间等因素影响较大,需要现场监测人员和分析人员严格控制采样和分析条件。     

典型钢铁企业汞排放水平及排放特征研究

以某典型钢铁企业为研究对象,测定企业废气、废水、固废汞排放水平,并分析汞排放特征。研究表明,球团、烧结、高炉工艺废气排口烟尘中汞排放浓度和排放速率明显低于烟气;汞主要以气态形式排放,烧结工艺排口废气汞最高浓度分别是其他2个排口的7倍和3倍。球团、烧结、高炉、电炉四工艺环节中,烧结汞排放速率占四工艺汞排放速率总和的87%。半干法脱硫、氨法脱硫、石灰石石膏脱硫对废气中汞的去除效率分别为90.0%、78.7%和29.9%。企业废水排放未检出汞,脱硫产生固废汞含量明显高于除尘产生固废汞含量,脱硫灰汞含量是脱硫石膏的15倍。     

臭氧氧化法污泥减量技术的试验研究

对臭氧氧化法污泥减量技术进行了试验研究。试验表明,污泥浓度和臭氧流量均会影响污泥减量效果。当SV%=40,Qo2=20L/h,氧污比为0.15gO3/gMLSS时,污泥去除率最高,达到67.95%,污泥浓度与时间的函数关系为:S=3209.60e-0.1428t(S—MLSS浓度,mg/L;e—指数常数t;—时间,h)。电镜观察表明,经过臭氧氧化,污泥菌胶团密度降低,丝状菌网状结构破坏,细胞质溶出,细胞量明显减少。臭氧氧化法污泥减量技术对于解决污泥问题具有指导意义。     

浅谈磷石膏的综合利用

根据磷石膏作为湿法生产磷酸过程中的副产品,且含有少量的P2O5和氟等有害成分,是生产厂家面临的磷石膏的处理和再利用这一实际问题,论述了磷石膏的综合利用情况,为磷石膏的利用和开发提供了研究和参考的方向。     

一种新型微生物絮凝剂的制备及对Cu2+去除性能的探究

以城市污水处理厂的脱水污泥为原料,通过超声波细胞破碎制备微生物絮凝剂。采用控制变量法考察污泥浓度、超声波破碎时间对絮凝剂絮凝效果的影响,并探究絮凝液的投加量、pH值、温度、振荡时间、振荡频率、共存金属等因素对5 mg/L Cu^2+模拟废水的去除效果,分析了微生物絮凝剂去除Cu^2+的作用机理。结果表明:当污泥质量浓度为100 g/L,超声波破碎时间15 min时,絮凝剂的絮凝效果最好;当pH值为6.5,温度50℃,絮凝液投加量40 mL,振荡时间1 min,振荡频率200 r/min时去除效果最佳。     

二氧化硫手工连续采样方法研究

方法一 四氯汞钾吸收液—盐酸付玫瑰苯胺比色法 本法检测限为0.30μg SO_2/10ml。 一、仪器: 1.吸收瓶:75ml多孔玻板吸收瓶。 2.大气采样器:流量范围0～1L/min,湖北省环保仪器研究所生产的成套设备。 3.72分光光度计。 二、采样: 用一个内装50ml吸收液的多孔玻板吸收瓶,以0.2L/min流量,从8:00至次日8:00,采样时间24±0.5小时,采样体积约为288L。记录采样口的温度、压力。采样后,将样品带回实验室分析,或保存在冰箱里,一周后一起分析。     

Process integrated modelling for steelmaking Life Cycle Inventory analysis

During recent years, strict environmental regulations have been implemented by governments for the steelmaking industry in order to reduce their environmental impact. In the frame of the ULCOS project, we have developed a new methodological framework which combines the process integrated modelling approach with Life Cycle Assessment (LCA) method in order to carry out the Life Cycle Inventory of steelmaking. In the current paper, this new concept has been applied to the sinter plant which is the most polluting steelmaking process. It has been shown that this approach is a powerful tool to make the collection of data easier, to save time and to provide reliable information concerning the environmental diagnostic of the steelmaking processes.     

铁矿石烧结过程中二噁英的防治对策

介绍了二噁英在烧结过程中的生成机理;针对烧结烟气二噁英的生成及排放特点,对烧结过程二噁英的减排方法进行了分析;提出了从源头—过程—末端综合治理及多种污染物协同控制的建议。     

A New Mathematical Approach in Environmental and Life Sciences: Gene–Environment Networks and Their Dynamics

An important research area in life sciences is devoted to modeling, prediction, and dynamics of gene-expression patterns. As clearly understood in these days, this enterprise cannot become satisfactory without acknowledging the role of the environment. To a representation of past, present, and most likely future states, we also encounter measurement errors and uncertainties. This paper surveys and improves recent advances in understanding the foundations and interdisciplinary implications of the newly introduced gene–environment networks, and it integrates the important theme of carbon dioxide emission reduction into the networks and dynamics. We also introduce some operational and managerial issues of practical working and decision making, expressed in terms of sliding windows, quadrants (modules) of parametric effects, and navigating (controlling) between such effects and directing them. Given data from DNA microarray experiments and environmental records, we extract nonlinear ordinary differential equations that contain parameters that have to be determined. For this, we employ modern (Chebychevian) approximation and (generalized semi-infinite) optimization. After this is provided, time- discretized dynamical systems are studied. A combinatorial algorithm with polyhedra sequences allows to detect the region of parametric stability. Finally, we analyze the topological landscape of gene–environment networks with its structural (in)stability. By embedding as a module and investigating CO₂ emission control and figuring out game theoretical aspects, we conclude. This pioneering work is theoretically elaborated, practically devoted to health care, medicine, education, living conditions, and environmental protection, and it invites the readers to future research.      

微波消解-原子吸收光度法测定土壤中铜锌铅镉镍铬

用微波消解－原子吸收光度法测定土壤中铜，锌，铅，镉，镍和铬。通过硝酸－氢氟酸－过氧化氢体系消解液对土壤样品消解，选择出微波最佳消解条件。对硝酸－盐酸－过氧化氢体系消解液和硝酸－氢氟酸－过氧化氢体系消解液进行消解对比试验，发现前者不能将土壤样品完全消解，后者能将样品消解完全，但需将消解液中剩余的酸赶尽，否则测定结果将明显偏低。微波消解土壤与传统电热消解相比，操作简便快速，可提高工作效率。     

Topsoil and Housedust Metal Concentrations in the Vicinity of a Lead Battery Manufacturing Plant

The aim of the study was to determine the extent of heavy metal pollution in the vicinity of a lead battery manufacturing plant in the Czech Republic, both in the general environment and within homes. Topsoils (0–5 cm) were sampled from 100 sites along 4 transects which crossed the battery factory, the town centre and outlying rural areas. Housedust samples were collected from 15 plant-workers' homes and 15 non plant-workers' homes located at various distances from the factory. Samples were analysed for levels of Pb, Zn, Cd, Cu, As and Sb, using ICP-AES. Soil concentrations of Pb, Cd, As and Sb peaked at the perimeter fence of the battery factory with Pb levels of up to 12 650 g g> ^-1. Concentrations of these metals decreased exponentially within 500 m of the plant. Whilst the battery factory does appear to be a source of all the metals with the exception of Zn, emissions do not appear to be transported to any great extent over distances of more than 0.5 km. Topsoil and housedust concentrations of Pb, Zn, Cd, Cu, As and Sb in the general Mlada Boleslav area do not appear to be significantly different from those recorded in a large scale survey of urban soils in the United Kingdom. A comparison of housedust Pb concentrations in homes of plant workers and non-plant workers suggests that there may be a small input of Pb into the home environment by battery plant employees.     

An Overview of Contaminant-Related Issues Identified by Monitoring in San Francisco Bay

The San Francisco Estuary Regional Monitoring Program for Trace Substances (RMP) began in 1993 and is sponsored by 74 local, state, and federal agencies and companies through their discharge or Bay use permits. The RMP monitors water, sediment, toxicity, and bivalve bioaccumulation at 25 sites in the Bay that are considered to represent "background" conditions. Several major environmental issues have been identified by the RMP. Polychlorinated biphenyls and mercury were often above water quality guidelines, and often occurred in fish tissues above U.S. Environmental Protection Agency (U.S. EPA) screening values. Concentrations do not appear to be decreasing, suggesting continuing inputs. Episodes of aquatic toxicity often occurred following runoff events that transport contaminants into the Bay from urbanized and agricultural portions of the watershed. Sediment toxicity occurred throughout the Bay, and has been correlated with concentrations of specific contaminants (chlordanes, polynuclear aromatic hydrocarbons) at some locations; mixtures of contaminants were probably also important. Since the RMP does not monitor all ecosystem components, assessments of the overall condition of the Bay cannot be made. However, in terms of contamination, the RMP samples suggest that the South Bay, and North Bay sites are moderately contaminated.     

Biomagnification factors (fish to Osprey eggs from Willamette River,Oregon, U.S.A.) for PCDDs,PCDFs, PCBs and OC pesticides

A migratory population of 78 pairs of Osprey (Pandion haliaetus) nesting along the Willamette River in westernOregon was studied in 1993. The study was designed to determinecontaminant concentrations in eggs, contaminant concentrationsin fish species predominant in the Ospreys diet, andBiomagnification Factors (BMFs) of contaminants from fish specieseaten to Osprey eggs. Ten Osprey eggs and 25 composite samplesof fish (3 species) were used to evaluate organochlorine (OC)pesticides, polychlorinated biphenyls (PCBs), polychlorinateddibenzo-p-dioxins (PCDDs), and polychlorinated dibenzofurans(PCDFs). Mercury was also analyzed in fish. Geometric meanresidues in Osprey eggs were judged low, e.g., DDE 2.3 g g^-1 wet weight (ww), PCBs 0.69 g g^-1, 2,3,7,8-TCDD 2.3 ng kg^-1, and generally well below known threshold values for adverse effects on productivity, and the population was increasing. Osprey egg residue data presentedby River Mile (RM) are discussed, e.g., higher PCDDs were generally found immediately downstream of paper mills and eggsfrom the Willamette River had significantly elevated PCBs and PCDDs compared to reference eggs collected nearby in the CascadeMountains. Prey remains at nest sites indicated that the Largescale Sucker (Catostomus macrocheilus) and NorthernPikeminnow (Ptychocheilus oregonensis) accounted for an estimated 90.1% of the biomass in the Osprey diet, and composite samples of these two species were collected from different sampling sites throughout the study area for contaminant analyses. With the large percentage of the fishbiomass in the Osprey diet sampled for contaminants (and fisheaten by Ospreys similar in size to those chemically analyzed),and fish contaminant concentrations weighted by biomass intake, a mean BMF was estimated from fish to Osprey eggs for the largeseries of contaminants. BMFs ranged from no biomagnification(0.42) for 2,3,7,8-TCDF to 174 for OCDD. Our findings for themigratory Osprey were compared to BMFs for the resident HerringGull (Larus argentatus), and differences are discussed. Webelieve a BMF approach provides some basic understanding ofrelationships between contaminant burdens in prey species offish-eating birds and contaminants incorporated into their eggs,and may prove useful in understanding sources of contaminants inmigratory species although additional studies are needed.     

An investigation on biological stability of product water generated by lab-scale and pilot-scale distillation systems

Material Disposal Area G is the primary low-levelradioactive waste disposal site at Los Alamos NationalLaboratory, New Mexico, and is adjacent to Pueblo of SanIldefonso lands. Pueblo residents and Los Alamos scientists areconcerned about radiological doses resulting from uptake of AreaG radionuclides by mule deer (Odocoileus hemionus) andRocky Mountain elk (Cervus elaphus), then consumption ofdeer and elk meat by humans. Tissue samples were collected fromdeer and elk accidentally killed near Area G and were analyzedfor ³H, ⁹⁰Sr, total U, ²³⁸Pu, ^{239, 240}Pu,²⁴¹Am, and ¹³⁷Cs. These data were used to estimatehuman doses based on meat consumption of 23 kg y^-1. Humandoses were also modeled using RESRAD, and dose rates to deer andelk were estimated with a screening model. Dose estimates tohumans from tissue consumption were 2.9 × 10^-3 mSv y^-1and 1.6 × 10^-3 mSv y^-1 from deer and elk, respectively,and RESRAD dose estimates were of the same order of magnitude. Estimated dose rates to deer and elk were 2.1 × 10^-4 mGyd^-1 and 4.7 × 10^-4 mGy d^-1, respectively. Allestimated doses were significantly less than established exposurelimits or guidelines.     

The Draft of the New German Guideline VDI 3782/8 to Model Automobile Exhaust Dispersion

The draft of the German guideline to calculate automobile exhaust dispersion is explained. It contains a two-stage-system: For first quick estimates the guideline contains the simple models MLuS and STREET. In case these models are not applicable or their results shows concentration levels close to the air quality standards, the more complex models PROKAS_V and MISKAM are recommended. PROKAS_V is a Gaussian plume model, MISKAM is a 3-dimensional microscale non hydrostatic flow model for built-up areas with an Eulerian dispersion model. The guideline comprises cases in rural areas without or with few adjacent buildings as well as urban areas with buildings near the roads. The contribution gives information about the models, typical results and some of the problems showing up presently.