兰州市室外大气细菌气溶胶浓度及粒径分布特征

在兰州市不同室外环境区域布设4个采样点,使用PSW-6型安德森（Andersen）6级筛孔撞击式空气微生物采样器采集大气细菌气溶胶,分析其浓度和粒径日变化特征。结果表明,不同季节各采样点的大气细菌气溶胶浓度上午时段为88 CFU/m3～1 335 CFU/m3,下午时段为78 CFU/m3～865 CFU/m3。除了夏季兴隆山上午时段外,其余不同季节各采样点上、下午时段的大气细菌气溶胶粒径均主要分布于Ⅰ级—Ⅳ级（＞2.10μm）,占比为 70.54%～93.94%;Ⅴ级（1.10 μm～2.10μm）和Ⅵ级（0.65 μm～1.10 μm）大气细菌粒子占比较低,仅为6.06%～29.46%。     

兰州市不同季节大气微生物气溶胶粒径及分布特征研究

大气微生物对人类危害不仅与微生物气溶胶浓度和种类有关,而且大气微生物气溶胶粒径尺度大小及其分布特征也是重要的影响因素.在兰州市城关区选取不同环境功能区对其室外大气微生物气溶胶粒径(D,μm)大小及分布特征进行研究,结果表明,不同环境功能区大气细菌、霉菌和放线菌气溶胶粒度分布特征存在季节性分布差异,其中大气细菌气溶胶粒径...     

粤北韶关市冬季大气颗粒物中多环芳烃的粒径分布特征

2012年12月4日—11日,使用微孔均匀撞击式采样器(MOUDI)连续7 d采集广东省韶关市3个环境空气监测点气溶胶样品,采用GC/MS测定包括美国国家环保局(USEPA)优控多环芳烃(Σ16PAHs)在内的17种PAHs的浓度水平,并分析Σ16PAHs的粒径分布特征和来源。结果表明:韶关市冬季气溶胶颗粒中Σ16PAHs的质量浓度为17.29 ng/m3~23.97 ng/m3;Σ16PAHs集中在1.0μm~3.2μm的积聚态和粗颗粒中,呈单峰分布特征;比值参数分析显示,韶关市大气颗粒物中PAHs主要来自燃煤和汽车尾气的排放。     

内蒙古干草原冬、春季大气气溶胶的若干特征观测研究

内蒙古半干旱草原区大气气溶胶浓度以及散射等特性对生态环境、气候变化与预测研究有重要意义,文利用2009年1～4月在锡林浩特观象台草原站的观测资料,分析了冬、春季背景大气气溶胶质量浓度、黑碳质量浓度、散射系数的分布特征。研究发现,背景天气下,PM10、PM2.5、PM1.0浓度值都较低,平均值分别为22.7、9.5、6.1μg/m3,3种PM浓度值间的相关性不同;黑碳浓度平均值为0.59μg/m3,小粒子中的含量较高,其日分布规律受人类活动影响较大,与各PM浓度分布有较大不同;散射系数平均值为31.2Mm-1,与PM10、PM2.5、PM1.0、黑碳质量浓度都显著相关。三种PM中,PM2.5对散射和吸收的影响最大。风速、相对湿度对不同粒径的PM以及黑碳浓度、散射系数的影响有所不同。     

一次连续在线观测分析天津市细颗粒物污染特征

根据2005年的5月17日—5月23日GR IMM(1.109#)谱分析仪在线观测结果考察天津市细颗粒物浓度和质量浓度特征。观测期间,天津市颗粒物数浓度平均值为1 124 cm-3,粒径分布为0.25μm~0.60μm,98.5%粒子的粒径0.65μm。同期PM10日均质量浓度值为204μg/m3,ρ(PM2.5)为104μg/m3,ρ(PM1.0)为82.9μg/m3。ρ(PM1.0)/ρ(PM2.5)超过80%,粒径1μm超细颗粒物为天津城市大气颗粒物的主要成分。     

宝鸡高新区黑碳气溶胶浓度特征及其影响因素研究

为研究宝鸡高新区黑碳(BC)气溶胶浓度的变化特征及其影响因素,利用2017年3月1日至2018年2月28日的BC气溶胶浓度、PM_(2.5)质量浓度以及风速风向数据,对该地区BC气溶胶质量浓度特征变化及其影响因子进行分析。结果表明,宝鸡高新区BC和PM_(2.5)质量浓度范围分别为0.35~6.18μg/m~3和8.01~192.20μg/m~3,平均值分别为(1.67±1.22)μg/m~3和(46.96±33.18)μg/m~3。BC气溶胶的背景质量浓度为(0.81±0.76)μg/m~3。BC与PM_(2.5)的相关系数为0.673,呈正相关。观测期间10—12月BC质量浓度较其他月份相对较高,其季节变化由大到小依次为冬季秋季春季夏季,这可能与采暖季用煤及气象条件不同有关。BC气溶胶的日变化有峰谷值,峰值出现在07:00—09:00和20:00—22:00,谷值出现在14:00—16:00。BC和PM_(2.5)质量浓度均随污染等级加重而增加。宝鸡高新区BC污染在西北风向下较为严重,且此时风速较小,BC质量浓度与风速的相关系数分别为-0.438,呈负相关,静风和非静风条件下BC平均质量浓度分别为2.50μg/m~3和1.53μg/m~3,表明静风条件下,污染物容易累积,导致BC质量浓度升高。     

多因素作用下高校阶梯教室生物气溶胶的分布特性研究

采用自然沉降法和撞击法两种实验测试方法,对比分析在不同季节、自然通风和人员活动多因素作用下的高校阶梯教室室内生物气溶胶分布特性及变化规律。结果表明:阶梯教室夏季室内生物气溶胶浓度高于冬季;教室内无通风和人员活动的情况下,室内生物气溶胶浓度大幅度下降,其平均衰减率为68%;教室内有自然通风时,室内生物气溶胶浓度与室外的趋于一致,室外空气源是影响室内生物气溶胶浓度的重要因素;人员活动会显著提高室内的生物气溶胶浓度,同时使得粒径分布状态发生改变,粒径为3.3μm~7.0μm生物气溶胶的比例从27.6%增加到59.8%。     

合肥市黑炭气溶胶浓度分布和变化特征研究

根据合肥市黑炭气溶胶自动在线监测结果、相关污染物监测数据、气象数据,分析了合肥市城区黑炭气溶胶的浓度分布特征。结果表明,2013年6月—2014年5月黑炭浓度的年平均值为(4.88±2.99)μg/m3,总体呈现春夏季浓度较低、秋冬季浓度较高的分布。黑炭浓度日变化呈双峰型,峰值出现在早07:00和晚20:00,早间峰值受大气扩散条件和人为活动的共同影响,晚间峰值受人为活动影响较大。在与其他污染物的相关性研究中,黑炭浓度与粒径较小的颗粒物PM1质量浓度相关性最好,波长为950 nm的测量通道测得的黑碳气溶胶与元素碳的相关性最好。     

福州市大气污染空间分布特征分析

利用2015年福州主城区6个大气国控点的6种主要大气污染物逐时监测数据、气象数据及空间基础数据等,通过增设站点后进行空间插值的方法分析大气污染物浓度的空间分布特征。结果表明:福州市大气中PM_(2.5)、PM_(10)最高值分别为35.57μg/m~3和62.35μg/m~3,高浓度区域集中在主城区中心和近郊区,其中台江区污染程度相对较高;O_3最高值为94.85μg/m~3,较高浓度主要集中在晋安区内海拔较高的森林地区;CO、SO_2和NO_2最高浓度低于一级标准浓度限值,高浓度区域分布在主城区中心。     

田湾核电站厂区及周围环境大气气溶胶中总α和总β放射性水平监测

通过2011—2013年对田湾核电站厂区及周围环境大气气溶胶中总α、总β放射性水平的监测,结果表明:该核电站厂区及周围环境大气气溶胶中总α、总β放射性浓度范围分别为0.023 m Bq/m3~0.296 m Bq/m3、0.240 m Bq/m3~2.460 m Bq/m3,放射性水平在本底范围内,未见明显差异;总α、总β放射性水平波动受气象条件影响,呈季节性变化特征。     

城市空气质量周报效用分析

介绍了世界上一些发达国家的空气污染预报的做法和采取的措施,阐述了我国开展空气质量预报的方针和方法,指出了周报是预报的基础工作。叙述了我国空气质量周报的污染参数的选取、污染指数的分级及其浓度限值和污染指数计算及确定,分析并总结了开展城市空气质量周报所发挥的效用是提高公众的环保意识,加大了治理污染的力度,转变了环境监测的职能,促进了环境监测事业的发展     

锅炉烟尘测试中锅炉负荷率的计算方法探讨

GB5468 -91规定 ,锅炉烟尘测试时 ,必须对锅炉的运行负荷进行测试 ,而实际监测过程中 ,许多锅炉房不具备测试的计量条件 ,为了解决这一问题 ,文章提出利用烟气量和空气过剩系数计算锅炉负荷率。在实际监测工作中 ,该方法方便、易于操作 ,所得结果和标准规定方法所得结果有很好的一致性     

水中总硬度测量不确定度的评定

采用EDTA滴定法测定水质总硬度的测量不确定度评定。充分考虑测量重复性、标准溶液的配制、滴定等过程对测量的影响,计算水中总硬度的测量相对合成标准不确定度为1·81×10-3。     

“湖泛”恶臭物质分析及来源浅析

介绍了中国南方"湖泛"中的恶臭物质及检测情况,采用常规分析和气相色谱-质谱(GC-MS)对"湖泛"水样进行检测,认为"湖泛"恶臭物主要是氨和硫醚类物质。根据"湖泛"发生的时间及频次,结合南方地区农业水稻秧田的农药使用情况,推断氨基甲酸酯类农药的使用可能是"湖泛"发生的诱因。     

Fractionation of heavy metals and assessment of contamination of the sediments of Lake Titicaca

Chemical weathering is one of the major geochemical processes that control the mobilization of heavy metals. The present study provides the first report on heavy metal fractionation in sediments (8–156 m) of Lake Titicaca (3,820 m a.s.l.), which is shared by the Republic of Peru and the Plurinational State of Bolivia. Both contents of total Cu, Fe, Ni, Co, Mn, Cd, Pb, and Zn and also the fractionation of these heavy metals associated with four different fractions have been determined following the BCR scheme. The principal component analysis suggests that Co, Ni, and Cd can be attributed to natural sources related to the mineralized geological formations. Moreover, the sources of Cu, Fe, and Mn are effluents and wastes generated from mining activities, while Pb and Zn also suggest that their common source is associated to mining activities. According to the Risk Assessment Code, there is a moderate to high risk related to Zn, Pb, Cd, Mn, Co, and Ni mobilization and/or remobilization from the bottom sediment to the water column. Furthermore, the Geoaccumulation Index and the Enrichment Factor reveal that Zn, Pb, and Cd are enriched in the sediments. The results suggest that the effluents from various traditional mining waste sites in both countries are the main source of heavy metal contamination in the sediments of Lake Titicaca.     

贵州黔东南州三板溪水库春季拟多甲藻水华特征

2011年3月13日对贵州省黔东南州三板溪水库进行春季浮游植物调查的结果表明,三板溪水库Ⅱ号采样点(下革东)发生以佩纳形拟多甲藻为优势种的拟多甲藻水华,细胞密度高达1.15×10⁷cell/L;板溪水库总氮的最低值为2.09 mg/L,总磷的最低值为0.95 mg/L,三板溪水库的总氮、总磷含量较丰富,不存在总氮或总磷是限制性因子;通过SPSS16.0统计软件分别进行Pearson 积距相关系数分析表明,氮磷比是三板溪水库发生拟多甲藻水华的主要影响原因。     

Evaluation of method of preparation of passive diffusion tubes for measurement of ambient nitrogen dioxide

This study was carried out in response to suggestions that the measurement of NO(2) by Palmes-type passive diffusion tubes (PDT) is affected by the method of preparation of the triethanolamine (TEA) absorbent coating on the grids. The following combinations of factors were investigated: TEA solvent (acetone or water), volume composition of TEA in solvent (50% or 20%), and grid coating method (dipping in solution prior to assembly or pipetting solution on after assembly). Duplicate PDTs prepared by each of the 8 methods were exposed in parallel, in urban air, for a total of 80 separate 1 week exposures. NO(2) concentrations derived from PDTs prepared by pipetting methods were significantly less precise than concentrations from dipping methods, with mean RSDs for duplicate measurements of 13.8% and 8.5%, respectively (n= 316 each category). Pipetting methods using solutions of 50% TEA composition were particularly imprecise (mean RSD 17.2%). Data from PDTs prepared by pipetting methods were systematically more poorly correlated with each other and with data from co-located chemiluminescence analysers, than corresponding data from PDTs prepared by dipping methods, indicating that more consistent accuracy was also obtained by the latter PDTs. The statistical evidence suggested that PDTs prepared by pipetting 50% TEA in water generally gave lower NO(2) concentrations. Although this is in agreement with a previous study, it is also possible that such an observation here may be a statistical artefact given the demonstrably poorer precision of this method. The general tendency of PDTs to show positive bias in NO(2) measurement in urban air in 1 week exposures was again evident in this study (mean biases at roadside and urban centre locations of +35% (n= 475) and +18% (n= 112), respectively) consistent with augmentation of within-tube NO(2) flux by chemical reaction between co-diffusing NO and O(3). Overall, it is recommended that the pipetting method of PDT grid preparation is avoided, or at least investigated further, because of the apparent degradation in precision and accuracy of NO(2) measurement. Potential reasons for the effect are discussed.     

实验室质量管理体系内部审核的实施

在实施GB/T15481-2000 idt ISO/IEC17025:1999标准《检测和校准实验室能力的通用要求》的过程中,通过实验室质量管理体系内部审核的实践与系统分析,识别出内部审核实施阶段的关键环节,提出召开首次会议、收集审核证据、确定审核发现和召开末次会议的技术方法,对提高内部审核的质量和有效性、获得可靠的审核结论具有重要意义。     

Environmental Assessment of the Impact of Ozone to the Neuston of the Sea-Surface Microlayer of the Gulf of Mexico

Substantial amounts of NOx (146 000 t/y) and total hydrocarbons (294 000 t/y) are released to the marine atmosphere by the large number of oil and gas operations over Federal waters of the Gulf of Mexico (GOM). Under appropriate meteorological conditions these emissions react to form ozone (0–54 g/m3 over-water) which can affect the marine environment. Using a dry deposition model, this work examines the amount of ozone derived from oil and gas offshore operations and deposited in the sea surface of the Gulf of Mexico, and assesses its impact on the neuston of the sea-surface microlayer. Surface integrated estimates of ozone deposited from oil and gas operations over the sea surface ranges from 400 kg to 1800 kg which results in sea surface concentrations of 15 g/m3. This estimate and the actual toxic ozone levels suggest no acute, toxic impacts to the neuston. However, indirect effects may occur through changes to the pelagic foodwebs and organic carbon pathways. Another potential pathway for ozone impacting the environment is through the production of bromate. Based on the concentrations and time scales (11–139 days) only sublethal effects appear to occur, but uncertainties associated with this assessment need to be further studied. From an ecological perspective, the environmental impacts and risks of NOx and VOC discharges from offshore platforms need to be assessed for neuston and other components of the marine ecosystem.     

实验室质量管理体系内部审核的策划

在实施GBT15481-2000(idtISOIEC17025:1999)标准《检测和校准实验室能力的通用要求》的过程中,通过实验室质量管理体系内部审核的实践与系统分析,识别出内部审核策划阶段的关键环节,提出审核范围确定、审核计划和抽样方案制订的技术方法,为有序高效地实施内部审核提供了行动指南。