Fe(Ⅱ)EDTA络合吸收-铁粉还原再生脱除NO性能

利用Fe(Ⅱ)EDTA络合吸收-铁粉间歇还原再生脱除NO并回收氨资源的方法,实验研究了铁粉还原再生Fe(Ⅱ)(NO)EDTA的过程及其影响因素。结果表明,以0.015 mol/L的Fe(Ⅱ)EDTA做吸收剂,在起始p H 5.5、温度323K条件下吸收400×10-6~500×10-6的NO,脱除率95%以上;铁粉还原再生Fe(Ⅱ)(NO)EDTA过程可用缩芯模型阐释;铁粉添加量与搅拌强度直接决定了铁粉质点数量,是影响反应的重要因素;实验中Fe(Ⅱ)(NO)EDTA络合液150 m L,氧气含量为5%时,搅拌速度900 r/min、粒径为0.12 mm的铁粉浓度5.3 g/L、温度353 K、p H=6为最适宜再生条件。     

白云石石灰结晶流化床污水除磷工艺优化

为了获取优化的污水除磷工艺,基于前期对白云石石灰结晶流化床去除厌氧消化上清液中磷的工艺条件和参数的初步探究,考察了不同酸化程度下白云石石灰释放Mg2+、Ca2+的效果,并根据MAP反应特点,选择出酸化液体积为5、6.5和10 m L,分别对应n(Mg)/n(P)为0.6、1.4、2.2进行后续实验。利用响应面法(RSM)对白云石石灰结晶流化床强化除磷工艺的影响因素进行分析和探讨,考察了p H值、n(Mg)/n(P)与停留时间(HRT)(分别记为X1、X2、X3)及各因素之间交互作用对磷去除率的影响,并利用扫描电子显微镜、X射线衍射和傅里叶变换红外光谱对产物进行表征,得出最佳工艺参数为p H=9.5、n(Mg)/n(P)=2.2、HRT=3.0 h。RSM法所建立的回归模型显著,实验精准度、精密度和可信度均在合理范围内,回归方程中X1、X2、X3、X1X2、X1X3、X21、X22、X23对磷去除率影响显著。产物MAP晶形较好,但由于废水的碱度较大(20 mmol/L),产物中含有大量的Ca CO3沉淀。     

芬顿试剂预处理杀螟丹农药废水

利用芬顿试剂(Fenton)氧化预处理杀螟丹农药废水,分别考察了H2O2与Fe SO4·7H2O投加量、初始p H、反应时间、温度和摇床转速对Fenton试剂处理杀螟丹废水的影响。结果表明,杀螟丹废水初始COD为676.8 mg/L时,取废水样100 m L,优化反应条件为Fenton试剂的用量1 g Fe SO4·7H2O+4 m L H2O2,初始p H值为3,搅拌强度为160 r/min的摇床转速,反应温度25℃,反应时间60 min。在优化反应条件下COD的去除率达到83.9%。通过Fenton降解,废水可生化性BOD5/COD从0.0745~0.0747上升至0.9066~0.9228,可生化性大幅提高,为后续生化处理创造了条件。考虑到运用于工业废水处理中经济成本等实际问题,建议选取Fenton试剂的用量0.5 g Fe SO4·7H2O+1 m L H2O2,COD去除效率能达到65.5%。     

印染RO浓水深度处理及回用

采用Fenton-石灰苏打法耦合工艺对某印染厂印染反渗透(RO)浓水进行深度处理。通过实验研究了不同H2O2和Fe2+投加量、p H和反应时间对废水COD去除率的影响,以及不同石灰和碳酸钠投加量对废水硬度的脱除效果,出水回用于染色工段进行染色实验。结果表明,在p H=3.0,Fe2+投加量为1.5 mmol/L,H2O2投加量为3.75 mmol/L,反应时间为45 min,石灰和碳酸钠投加量分别为450 mg/L和1 000 mg/L的条件下,出水COD和硬度的去除率可分别达到73.9%和85.0%,耦合工艺出水水质符合该厂回用染色水标准,且减少了盐的使用,可实现印染RO浓水回用。     

工艺参数对表面活性剂洗涤修复PAHs污染土壤的影响

采用土壤洗涤(soil-washing)技术,分别用TritonX-100和Tween-80为强化洗涤剂研究了搅拌强度、洗涤时间、表面活性剂浓度、液固比、温度和间歇搅拌6个工艺参数对PAHs污染土壤洗涤效果的影响。通过一系列烧杯搅拌实验得到最佳洗涤工艺参数。TritonX-100和Tween-80的最佳洗涤时间分别是30 min和60 min,其他工艺参数最佳条件均相同。分别是搅拌强度为250 r/min,表面活性剂浓度为5 g/L,液固比为10∶1,温度为室温和连续搅拌。在此最佳工艺参数条件下,污染土中PAHs的残留率<10%,基本上满足目标污染物的修复目标。应用表面活性剂强化洗涤技术修复PAHs污染土壤是合理和可行的。     

黄磷尾气烧制高活性石灰

黄磷生产过程中产生的黄磷尾气富含高浓度CO、H2,是非常好的燃料。实验研究了应用黄磷尾气烧制石灰时,黄磷尾气的杂质含量和燃烧特性对石灰活性度的影响。实验结果表明,石灰活性度随着黄磷尾气杂质含量的降低而增大;随着石灰窑燃烧梁的温度和黄磷尾气中CO含量的增加而增大,在CO含量为92%时、空气过剩系数为1.3时,石灰活性度达到《冶金石灰标准》(YB/T 042-2014)普通冶金石灰一级标准。     

响应面法优化UV/H_2O_2光氧化法处理高浓度LAS废水

采用响应面法对UV/H2O2光氧化法处理高浓度LAS废水的工艺参数进行了系统研究。根据Box-Behnken Design(BBD)设计原理,以初始pH与H2O2投加量、反应时间和温度为主要影响因素,设计4因素3水平共29个实验点的实验方案,并建立了二次响应面拟合模型。方差分析表明,初始pH与H2O2投加量、反应时间和温度以及初始pH和H2O2投加量、H2O2投加量和温度之间的交互作用,对实验结果具有显著性影响。实验得到的光氧化高浓度LAS废水最佳工艺条件,pH为4.0,H2O2投加量为40 mmol/L,反应时间为90 min,温度为25℃,在此条件下,LAS的平均去除率为98.1%。     

微气泡曝气O_3/H_2O_2处理RO浓水的效能及影响因素

采用O3/H2O2高级氧化工艺处理炼油厂反渗透(RO)浓水,用溶气泵加压溶气并产生微气泡强化传质,确定装置运行条件,考察气体中臭氧浓度、H2O2/O3初始摩尔比、pH和温度对O3/H2O2处理RO浓水效果的影响,并对RO浓水处理效能进行研究。结果表明,随着气体中臭氧浓度的增加,COD的去除率基本呈线性增加;加入适当量H2O2能提高臭氧氧化RO浓水的效果,H2O2/O3初始摩尔比在0~0.8范围内,COD的去除率先增加后下降,H2O2/O3初始摩尔比为0.5时COD去除率最大;pH从6.84增加到9.01,COD去除率逐渐增大,pH为10.03时COD去除率反而降低;在14~28℃范围内,温度低时,升高温度COD去除率增加较大,温度较高时,升高温度对COD去除率的影响较小。为考察该工艺的稳定性,在H2O2/O3初始摩尔比为0.5、溶液pH为8~9、臭氧浓度为80~100 mg/L、温度为10~28℃条件下,对COD为90~140mg/L的RO浓水氧化处理4~10 h,出水COD维持在39.9~49.9 mg/L,达到《城镇污水处理厂污染物排放标准(GB 18918-2002)》中的一级A标准;去除1 g COD消耗O31.4~3.3 g,消耗O3与H2O2的总氧量为2.2~4.4 g。     

天然沸石特性对含磷废水净化效果的影响

由于磷的存在导致水体产生富营养化等水质恶化的现象异常严峻,基于天然沸石处理含磷废水的实验方法,研究了沸石吸附废水溶液中磷素的净化过程,考察了天然沸石的粒径大小、用量、吸附净化时间、搅拌强度、pH值等因素对吸附作用的影响,分析确定了不同条件下沸石吸附磷素的理想条件.结果表明,随着沸石粒径减小,吸附剂的比表面积增大,吸附质的扩散速率也越大,对吸附越有利;随着沸石投加量的增加,废水中磷元素的去除率呈现出“增加-减少-增加”的演化趋势;天然沸石的吸附具有快速吸附,缓慢平衡的特点;最佳的搅拌强度是在150 r/min;在中性或者碱性条件下,沸石的去除率比较理想.     

响应面法优化超临界水氧化降解喹啉废水

采用基于中心复合设计(CCD)的响应面分析方法,以H2O2为氧化剂,对超临界水氧化降解喹啉废水的影响因素进行了探讨和分析,考察了温度、压力、停留时间、氧化剂过量倍数对废水降解的影响。在温度380～460℃,压力24～28 MPa,停留时间20～60 s,氧化剂过量倍数0%～400%的条件下分析了TOC去除率的变化。由Design-Expert7.0软件设计分析了实验数据,得到一个二次响应曲面模型,通过实验对模型进行了验证,结果表明,响应面模型的预测值与实验值吻合较好。在最佳操作点温度441℃,压力25 MPa,停留时间60 s,氧化剂过量2.48倍的条件下,TOC去除率达到最高值(95.19%)。     

石灰与石灰石作湿法脱硫剂的比较

石灰、石灰石是最常用的湿法脱硫剂。从反应机理、运行控制指标、液气比和钙硫比（化学过量比）、浆液循环池等方面对其性能作了比较。两者的脱硫机理、运行控制指标不同,受温度的影响程度也不同。两系统的最小液气比分别为10．0和5．6,化学过量比分别为1．05～1．15和1．25～1．60。前者的脱硫效力优于后者。     

Degradation of 2,4,6-trinitrotoluene in water and soil slurry utilizing a calcium peroxide compound

The degradation of 2,4,6-trinitrotoluene was examined in pure water and contaminated soil slurry using calcium peroxide as a source of solid hydrogen peroxide and oxygen. The extent of TNT oxidation was compared with that obtained by using hydrated lime, which is normally generated by slurrying CaO2 in water and contained in CaO2 technical formulation (approximately 50%, w/w). Complete TNT degradation occurred between 280 min, 0.1% CaO2/Ca(OH)2 and 20 min, 1% CaO2/Ca(OH)2. A large part of the generated oxidation products, 80-90%, were absorbed on the solid calcium hydroxide, whereas the remaining 10-20% was detected in solution until 48 h. Removal of nitro groups was extremely effective in CaO2 slurry, where all the nitrogen (3 mol per mol of TNT) was removed from TNT within 240 min. Respect to calcium hydroxide, the peroxy compound liberated H2O2 in solution, 370 mg l-1 at 0.2% CaO2, w/v, which then decomposed within 480 min. Most of the 14C-TNT was retained more strongly on the calcium hydroxide generated by slurrying CaO2. This pool remained adsorbed on the solid until pH dropped below 5.8. The treatment of a contaminated soil slurry, 700 mg TNT kg-1, reduced CH3CN extractable TNT below 20 mg kg-1 at very low concentration of CaO2/Ca(OH)2, approximately 0.2%, w/w. Both oxidants do not lead to soil sterilization as the phosphorus added to neutralize the pH serves as a source of nutrient for the soil biomass.     

An efficient venturi scrubber system to remove submicron particles in exhaust gas

An efficient venturi scrubber system making use of heterogeneous nucleation and condensational growth of particles was designed and tested to remove fine particles from the exhaust of a local scrubber where residual SiH4 gas was abated and lots of fine SiO2 particles were generated. In front of the venturi scrubber, normal-temperature fine-water mist mixes with high-temperature exhaust gas to cool it to the saturation temperature, allowing submicron particles to grow into micron sizes. The grown particles are then scrubbed efficiently in the venturi scrubber. Test results show that the present venturi scrubber system is effective for removing submicron particles. For SiO2 particles greater than 0.1microm, the removal efficiency is greater than 80-90%, depending on particle concentration. The corresponding pressure drop is relatively low. For example, the pressure drop of the venturi scrubber is approximately 15.4 +/- 2.4 cm H2O when the liquid-to-gas ratio is 1.50 L/m3. A theoretical calculation has been conducted to simulate particle growth process and the removal efficiency of the venturi scrubber. The theoretical results agree with the experimental data reasonably well when SiO2 particle diameter is greater than 0.1 microm.     

Removal of non-steroidal anti-inflammatory drugs ibuprofen and ketoprofen from water by emulsion liquid membrane

In this work, the removal of the worldwide non-steroidal anti-inflammatory drugs ibuprofen (IBP) and ketoprofen (KTP) by emulsion liquid membrane (ELM) was carried out. An ELM system is made up of hexane as diluent, Span 80 as the surfactant and sodium carbonate as the inner aqueous solution. Effect of experimental conditions that affect the extraction of IBP such as surfactant concentration, emulsification time, sulfuric acid concentration in external phase, acid type in external phase, internal phase concentration, type of internal phase, stirring speed, volume ratio of internal phase to membrane phase, treatment ratio, IBP initial concentration, diluent type and salt was investigated. The obtained results showed that by appropriate selection of the operational parameters, it was possible to extract nearly all of IBP molecules from the feed solution even in the presence of high concentration of salt. Under optimum operating conditions, the efficiencies of IBP removal from distilled water (99.3 %), natural mineral water (97.3 %) and sea water (94.0 %) were comparable, which shows that the ELM treatment process represents a very interesting advanced separation process for the removal of IBP from complex matrices such as natural and sea waters. Under the optimized experimental conditions, approximately 97.4 % KTP was removed in less than 20 min of contact time.     

支撑气膜法脱除／回收垃圾渗滤液中氨氮

利用由微孔疏水性聚丙烯中空纤维制成的工业级膜组件对垃圾渗滤液中氨氮进行支撑气膜法脱除研究,考察了泡沫分离．石灰絮凝等预处理技术对垃圾渗滤液表面张力及COD值的处理效果,在此基础上研究了物料因素和操作因素对膜传质性能的影响,并对该工艺的长期操作稳定性进行了研究。实验结果表明该预处理技术不仅可显著提高垃圾渗滤液的表面张力,还可大大降低其色度和COD值。当进料流量为100L／h、进料氨氮浓度为1000～3000mg／L、硫酸吸收液流量为200L／h、硫酸浓度为6％～10％、温度为20～30℃时,支撑气膜过程（两级膜组件串联）可有效脱除垃圾渗滤液中99％以上的氨氮,同时得到含10％～15％硫酸铵的水溶液作为副产品。工业级支撑气膜组件在连续运行的2个月内保持了良好的传质稳定性。     

Influence of metal oxides on PCDD/Fs formation from pentachlorophenol

Chlorophenols (ClPhs) are considered as important precursors for PCDD/Fs formation. The influences of series of metal oxides including MgO, Al2O3, CaO, BaO, TiO2, V2O5, MnO2, Fe2O3, Co3O4, CuO, Ag2O, ZnO, HgO, SnO, PbO, La2O3, CeO2, and Eu2O3 on PCDD/Fs formation from pentachlorophenol (PCP) were investigated in a laboratory-scale reactor. The results indicated that most of the above metal oxides have obvious suppressing effects on the total amount of PCDD/Fs formation from precursor PCP except for CuO, ZnO, MnO2, TiO2 and Co3O4 with promotion effects at 280 degrees C for 2 h. Although MgO, Al2O3, Fe2O3, PbO, La2O3 and Eu2O3 could reduce the amount of octachlorinated dibenzo-p-dioxin (OCDD), they promote the formation of more toxic 1,2,3,4,6,7,8-HpCDD at the same time. The total suppressing efficiencies of several metal oxides including CaO, BaO, PbO, Ag2O, HgO and SnO which have lower Z/r (charge to radius ratio) <2 are all over 90%. The theories of generalized acid-base and atomic parameter (Z/r) were used to speculate the effecting mechanisms. The factors including time and temperature on suppressing efficiencies of CaO, BaO and PbO have also been studied in the present paper. The results showed that the total suppressing efficiencies of CaO, BaO and PbO increase with the increase of heated time and temperature.     

生石灰孔结构对高温脱硫性能的影响

喷钙脱硫工艺的炉内脱硫率 ,不仅受工艺参数的影响 ,还与石灰石分解生成的新生CaO或直接喷入的CaO的表面结构有关。本研究用同一石灰石经不同方法 (煅烧、过烧、煅烧 -水合 -脱水等 )制备了四种具有不同比表面积和孔结构的生石灰。高温脱硫研究表明 :这四种不同孔结构的生石灰 ,具有不同的脱硫率。通过对高温脱硫前后吸着剂宏观结构变化的对比 ,发现半径小于 30 的孔易被反应产物堵塞 ,因而脱硫能力有限 ,而半径大于 5 0 的孔对脱硫更有效。本研究将为提高炉内喷钙的脱硫率、研制和开发高效脱硫剂提供新的途径。     

Product Guide/1982

Abstract

An efficient venturi scrubber system making use of heterogeneous nucleation and condensational growth of particles was designed and tested to remove fine particles from the exhaust of a local scrubber where residual SiH₄ gas was abated and lots of fine SiO₂ particles were generated. In front of the venturi scrubber, normal-temperature fine-water mist mixes with high-temperature exhaust gas to cool it to the saturation temperature, allowing submicron particles to grow into micron sizes. The grown particles are then scrubbed efficiently in the venturi scrubber. Test results show that the present venturi scrubber system is effective for removing submicron particles. For SiO₂ particles greater than 0.1 μm, the removal efficiency is greater than 80–90%, depending on particle concentration. The corresponding pressure drop is relatively low. For example, the pressure drop of the venturi scrubber is ～15.4 ± 2.4 cm H₂O when the liquid-to-gas ratio is 1.50 L/m³. A theoretical calculation has been conducted to simulate particle growth process and the removal efficiency of the venturi scrubber. The theoretical results agree with the experimental data reasonably well when SiO₂ particle diameter is greater than 0.1 μm.     

Effects of lime amendment on availability of heavy metals and maturation in sewage sludge composting

A batch composting study was performed to evaluate the feasibility of co-composting sewage sludge with lime, aiming at reducing the availability of heavy metals in the sludge compost. Sewage sludge with sawdust as bulking agent was amended with lime at 0, 0.63, 1.0, and 1.63% w/w, and composted for 100 days in laboratory batch reactors. The changes in temperature, pH, electrical conductivity (EC), and extractable heavy metal contents were measured while compost maturity was determined by C/N(organic) and cress seed germination during the composting period. Liming raised pH of compost effectively at the initial stage of composting and caused a decrease in EC through precipitation of soluble ions. Lime amendment also significantly reduced water-soluble and Diethylene triamine pentracetic acid (DTPA)-extractable metal contents. The maximum reductions were 60 and 40% for Cu, 80 and 40% for Mn, 55 and 10% for Zn, and 20 and 25% for Ni at the end of the composting period for the lime-amended sludge as compared to the control. In spite of the inhibitory effect of lime amendment on the decomposition activity of sewage sludge, all treatments reached maturation after 63 days of composting as indicated by the results of C/N(organic) ratio and cress seed germination test results. A lime amendment of < or =1.0% is recommended to co-compost with sewage sludge.     

Spray-dry desulfurization of flue gas from heavy oil combustion

An experimental investigation on sulfur dioxide removal in a pilot-scale spray dryer from the flue gas generated by combustion of low-sulfur (S) heavy oil is reported. A limewater slurry was sprayed through an ultrasonic two-fluid atomizer in the spray-dry chamber, and the spent sorbent was collected downstream in a pulse-jet baghouse together with fly ash. Flue gas was sampled at different points to measure the desulfurization efficiency after both the spray-dry chamber and the baghouse. Parametric tests were performed to study the effect of the following variables: gas inlet temperature, difference between gas outlet temperature and adiabatic saturation temperature, lime-to-S ratio, and average size of lime particles in the slurry. Results indicated that spray drying is an effective technology for the desulfurization of low-S fuel oil flue gas, provided operating conditions are chosen carefully. In particular, the lowest gas inlet and outlet temperatures compatible with baghouse operation should be selected, as should a sufficiently high lime-to-S ratio. The attainment of a small lime particle size in the slurry is critical for obtaining a high desulfurization efficiency. A previously presented spray-dry flue gas desulfurization model was used to simulate the pilot-scale desulfurization tests, to check the ability of the model to predict the S capture data and its usefulness as a design tool, minimizing the need for pilot-scale experimentation. Comparison between model and experimental results was fairly good for the whole range of calcium/S ratios considered.