微波活化对Ca(OH)2孔隙结构及脱氯性能的影响

采用微波炉对一定质量的氢氧化钙样品进行活化,利用压汞仪考察了不同微波活化时间及脱氯反应前后的Ca(OH)2总比孔表面积、分段比表面积和孔径分布的变化,并在脱氯实验台上对脱氯效率进行实际测试.结果表明,微波活化存在一个最佳时间,在此时间内样品比孔表面积增大50%左右,而超过这一时间样品比表面积回复性减小;微波活化主要通过增加3～20 nm孔径段的微孔为样品提供更大比表面积;这些新增加的微孔在脱氯反应过程中被完全利用或消耗;最佳活化时间下的微波活化使Ca(OH)2在较低Ca/Cl摩尔比下获得更大脱氯效率,Ca/Cl摩尔比=4.1时,脱氯效率增加了20%.     

钙化物在废弃物基活性炭制备过程中的影响

研究了以城市垃圾中3种典型的固体有机废弃物——锯木屑、纸张和塑料的热解产物(分别简称木炭、纸炭和塑料热解物)为原料,水蒸气为活化剂制备废弃物基活性炭时钙化物含量对活化过程、活性炭吸附性能(以碘值表征)及其孔结构的影响。结果表明,钙化物可加快活化反应的速度,且钙化物含量在1.5％时活化反应速度即已不再随钙化物含量的增加而增加;活性炭的吸附性能则随钙化物含量的增加而减少,同时钙化物对活性炭的孔径分布基本无影响,但降低了活性炭的比表面积、微孔孔容及中孔孔容;钙化物的2种前驱体（即CaO和Ca(OH)₂）对活化过程具有相同的催化作用。     

不同改性方式对竹炭净化气态氮氧化物效果的影响

为了研究不同表面改性方法对竹炭空气净化效果的影响,测定了化学药剂活化、超声处理、微波处理后的改性竹炭对低浓度氮氧化物的净化效果。结果表明:活化剂浸渍后的竹炭,对氮氧化物净化效率降低,净化速度减慢;微波功率越大、辐照时间越长,改性后竹炭对氮氧化物处理效率越大,但辐照时间达到一定程度后,竹炭对氮氧化物的处理效率增大变得缓慢;超声处理后的竹炭对NO的处理效率比改性前有明显提高。BET测试结果表明,竹炭产品用微波和超声处理后,平均孔径、微孔表面积和比表面积均比活化前增大;而经过活化剂浸渍后,微孔面积和比表面积都显著下降。因此建议采用微波及超声方式对竹炭进行活化。     

剩余污泥制备活性炭及其应用研究

以城市污水处理厂二沉池排出的剩余污泥为原料,采用不同活化方法制备活性炭,同时对比活化效果,研究了制备工艺条件对污泥活性炭吸附性能及产率的影响。结合比表面积、孔径分布和扫描电镜表征分析,对制备的污泥活性炭的性能进行评价,并探讨了污泥活性炭作为水处理吸附剂的去除效果。结果表明,以ZnCl₂为活化剂制备的活性炭性能较好,其最佳制备条件为：活化温度550℃,活化时间45 min,ZnCl₂浓度40％,固液比1∶2。制得的污泥活性炭的碘吸附值为496 mg/g,产率为51.8％,比表面积为301.4 m²/g,孔体积为0.37 mL/g,微孔体积为0.08 mL/g,平均孔径为5.78 nm。将该产品用于处理城市污水,投加量为0.8％,吸附平衡时间约为60 min时,对COD的去除率为81％,吸附容量为42.53 mg/g。     

用于干式脱污的CaO蒸汽活化实验研究

利用小型活化转炉实验台对以CaO为主要成分的钙基脱污剂在300～650℃的温度范围内进行蒸汽活化处理,结合X射线衍射和压汞仪的分析结果,初步探讨了蒸汽活化的机理.研究表明,蒸汽活化温度在600℃以上时,脱污剂孔隙结构有显著的改善,比孔容积和比表面积有着显著的增加,微孔(＜100nm)的数量大量增加,而低温下蒸汽活化的效果不是十分明显;研究还发现高温下延长活化时间有利于改善脱污剂的孔隙结构.     

用于干式脱污的CaO蒸汽活化实验研究

利用小型活化转炉实验台对以CaO为主要成分的钙基脱污剂在300～650℃的温度范围内进行蒸汽活化处理,结合X射线衍射和压汞仪的分析结果,初步探讨了蒸汽活化的机理.研究表明,蒸汽活化温度在600℃以上时,脱污剂孔隙结构有显著的改善,比孔容积和比表面积有着显著的增加,微孔（＜100nm）的数量大量增加,而低温下蒸汽活化的效果不是十分明显;研究还发现高温下延长活化时间有利于改善脱污剂的孔隙结构.     

微波活化制备加拿大一枝黄花活性炭及对Cd（Ⅱ）的吸附

以入侵植物加拿大一枝黄花为原料,在400℃氮气保护下,直接碳化90 min后,以KOH为活化剂,微波活化的方法制备了高比表面积微孔活性炭SCAC。结果显示活性炭SCAC的表面面积为1 888 m2/g,总孔容量为0.804 cm3/g,微孔容量为0.741 cm3/g,平均孔径0.567 nm,微孔平均孔径0.488 nm。通过静态吸附实验研究了活性炭添加量、溶液初始浓度、初始pH及吸附时间对SCAC吸附Cd(Ⅱ)的影响,通过动力学方程拟合探讨了活性炭对Cd(Ⅱ)的吸附机理。结果表明,吸附平衡时间、最佳pH及活性炭添加量分别为120 min、pH>7.5及0.05 g/50 mL,活性炭SCAC吸附动力学过程符合准二级方程模型。     

废活性炭微波再生新工艺的研究

提出用微波加热一二氧化碳活化法再生乙酸乙烯合成用触媒载体废活性炭工艺。采用条件实验法研究了活化时间、二氧化碳流量和微波功率对活性炭碘吸附值，亚甲基蓝吸附值和再生得率的影响，得到微波辐射加热二氧化碳活化再生乙酸乙烯用触媒载体废活性炭的最佳工艺条件为活化时间25min，二氧化碳流量0．2L／min，微波功率700w。在此条件下制得的活性炭碘吸附值为1158．02mg／g、亚甲基蓝吸附值为240mv,／g、得率为74．19％。并对活性炭进行了比表面积的测定和孔结构的分析，活性炭的比表面积为1308．13m^2／g，总孔容为0．76mL／g。     

吸附邻氯酚的超高交联树脂微波辅助再生研究

以NDA-150超高交联树脂为吸附剂，邻氯酚为吸附质，氢氧化钠稀溶液为脱附剂，采用微波间歇辐照的方法，对吸附氯酚树脂的再生过程进行了研究。系统分析了微波功率、辐照时间、碱液浓度对脱附效果的影响，并确定了最佳脱附条件。结果表明，微波辐照再生速度非常快。与传统热脱附不同，微波再生过程中脱附效率并不随碱浓度的增加而升高，微波辐照功率和辐照时间对脱附效果影响明显。树脂经多批次微波辐照，吸附性能和化学结构保持稳定。     

微波促进含Cr(VI)-H2O2体系降解甲基橙溶液的研究

研究了微波辐射下Cr(VI)－H₂O₂催化降解甲基橙溶液的行为，探索了微波功率、微波辐射时间、pH值、H₂O₂浓度、Cr(VI)等对甲基橙溶液脱色率和COD去除率的影响。研究结果表明，Cr(VI)-H₂O₂能形成类Fenton体系；微波辐射可提高H₂O₂产生羟基自由基(·OH)的效率。1000 mg/L的甲基橙溶液，在Cr(VI)浓度为10.0 mmol/L、pH值为2.5、H₂O₂浓度为20.0 mmol/L、微波功率为700W下加热2 min，甲基橙溶液的脱色率为99.2%，COD去除率为82.8%。     

Optimization of Height of Release of Air Pollutants

A number of key projects in the Environmental Protection Agency (EPA) particulate R&;D program having applicability to industry are presented. For electrostatic precipitators (ESP) there is presented the result of work on large diameter discharge electrodes which provide a decrease in penetration of up to a factor of 4 when compared to conventional small diameter electrodes. Also discussed is the multistage ESP which provides a collection efficiency that would require a collecting plate area 4 or 5 times larger with conventional ESP technology. The E-SOX technology makes use of the multistage concept to free up space in the ESP for SO₂ removals of up to 90%. Electrostatically augmented fabric filtration provides a reduction in pressure drop of about 5 0% as compared to conventional fabric filtration. Wind tunnel modeling of windbreaks for material storage piles indicates a potential for providing engineering design data that would allow significant emission reduction caused by wind erosion     

Investigation of the characteristics of the reflectivity of clouds

This paper investigates some of the reflectivity characteristics that clouds (when modelled as solid bodies) must exhibit to be compatible with observations that the reflecting surface of a cloud (i) appears almost equally bright across its face, (ii) is brightest when the cloud is opposite to the Sun but decreases in brightness as the cloud moves to other positions and (iii) increases in brightness with increasing optical thickness of the cloud in the observer's line of sight. These observations, respectively, are shown to imply that the peak value of the bidirectional total reflectivity from a cloud surface (i) increases in inverse proportion to the cosine of the angle between the Sun and the normal to the cloud surface, as the incident angle increases, (ii) appears to be directed back in the direction of the incident radiation, and (iii) increases as optical thickness of the cloud in the observer's line of sight increases. The results could have application in many fields (e.g. modelling diffuse radiance distributions for cloudy skies).     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

扬中生态环境建设的思考与实践

结合扬中生态环境的基本情况和存在的不足，进行了具体分析，对扬中未来生态建设的发展方向提出了建议及实施措施。     

实验室质量管理体系内部审核的实施

在实施ISO／IEC17025：1999标准《检测和校准实验室能力的通用要求》过程中，通过实验室质量管理体系内部审核的实践与系统分析，识别出内部审核实施阶段的关键环节，提出召开首次会议、收集审核证据、确定审核发现和召开末次会议的技术方法，对提高内部审核的质量和有效性、获得可靠的审核结论具有重要意义。     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

Impact of overexploitation of shellfish: northeastern coast of India

India has a very extensive coastline of about 7515 km, rich in diverse living resources. These resources continue to deteriorate with rampant harvesting or are altered for other uses such as aquaculture and fisheries. The present paper deals with degrading coastal habitats in northeastern India, and projects the intensity of the stress arising from the collection of tiger prawn seeds (Penaeus monodon) for aquacultural farms and molluskan shells for poultry feed and edible lime. Indiscriminate exploitation of these resources leads to a heavy reduction of the species concerned and other associated marine communities. The magnitude of such destruction has been quantified. The impacts of biodiversity loss and their after-effects on the ecobalance of this coastal system have become a matter of great concern to ecologists to maintain security and sustainability. The authors propose a public awareness program on themes relating to the importance of biodiversity for human livelihoods.     

Comparison of methods for evaluation of activity of photocatalytic films

Objective

This work aims to investigate the correlation between the photocatalytic activity determined by methylene blue bleaching (DIN 52980), stearic acid degradation, and degradation of acetone in gas phase.

Method

The photocatalytic TiO₂ coatings included in this investigation ranged from thin commercially available coatings (Activ^TM and BioClean^TM) and ready to use suspensions (Nano-X PK1245) to lab-produced PVD and sol?Cgel coatings. XRD analysis of the photocatalytic coatings showed that all the coatings consisted of nanocrystalline anatase, although the thickness and porosity varied considerably.

Results

The study showed that the reproducibility of the activity measurements was good. However, more importantly, the investigation showed that there is a good correlation between the activities determined by the different methods even though the characteristics of the photocatalytic coatings and the organic probe molecules varied considerably.

Conclusion

The overall findings of this work suggest that there is a good correlation between the investigated methods. These results are promising for the future work concerning standardization of methods for determination of the activity of photocatalytic films.