Soluble and insoluble fractions of heavy metals in wet and dry atmospheric depositions in Bologna,Italy

Atmospheric depositions were collected monthly using a modified wet and dry sampler (dry deposition was collected on a water surface) located in Bologna, a northern Italian urban area, to evaluate the impact of airborne heavy metals on the local pollution load. Wet deposition samples were filtered and heavy metal contents in soluble and insoluble fractions were determined. The same procedure was applied to the water samples which collected dry deposition. The entire procedure was tested using a certified reference material (CRM), which provided satisfying recovery results. The percentage of heavy metal soluble fraction in dry deposition was generally lower than in wet one; Cd, V, Cu and Zn showed a higher average solubility than Cr, Ni and Pb both in wet and dry deposition. Factor analysis, after a varimax rotation of principal components, suggested possible anthropogenic sources which explain different metal deposition patterns. This data analysis also allowed to distinguish different clusters formed by monthly fluxes of heavy metals.     

Overall elemental dry deposition velocities measured around Lake Michigan

Overall dry deposition velocities of several elements were determined by dividing measured fluxes by measured airborne concentrations in different particle size ranges. The dry deposition measurements were made with a smooth surrogate surface on an automated dry deposition sampler (Eagle II) and the ambient particle concentrations were measured with a dichotomous sampler. These long-term measurements were made in Chicago, IL, South Haven, MI, and Sleeping Bear Dunes, MI, from December 1993 through October 1995 as part of the Lake Michigan Mass Balance Study. In general, the dry deposition fluxes of elements were highly correlated with coarse particle concentrations, slightly less well correlated with total particle concentrations, and least well correlated with fine particle concentrations. The calculated overall dry deposition velocities obtained using coarse particle concentrations varied from approximately 12 cm s⁻¹ for Mg in Chicago to 0.2 cm s⁻¹ for some primarily anthropogenic metals at the more remote sites. The velocities calculated using total particle concentrations were slightly lower. The crustal elements (Mg, Al, and Mn) had higher deposition velocities than anthropogenic elements (V, Cr, Cu, Zn, Mo, Ba and Pb). For crustal elements, overall dry deposition velocities were higher in Chicago than at the other sites.     

Materials selection for a dry atmospheric mercury deposits sampler.

In order to develop a sampler for measuring dry deposition rates for atmospheric mercury, suitable materials are needed that neither adsorb nor release mercury. In this paper, four materials (polyvinyl chloride (PVC), acrylonitrile-butadiene-styrene (ABS), Teflon and glass) were tested. Each of the materials was placed in a beaker containing mercuric solution under varied conditions for pH, preservative concentration, initial mercuric concentration, temperature, acid type and contact time of the material. The concentrations of the mercuric solutions were determined using the cold-vapor atomic absorption (CVAA) technique. The experimental results show that glass has the lowest absolute net adsorption rates (NARs) of 0.026-1.13 pg/m2 among the materials tested. Teflon, PVC and ABS have NARs ranging from 0.54 to 10.4 microg/M2 over an adsorption duration of one or two weeks. ABS has significantly higher adsorption rates for mercury than PVC and Teflon, indicating its inappropriateness as the material for building the sampler. Teflon and PVC will be the materials of choice for the sampler. The experimental results can also be used in establishing appropriate sampling conditions in the field.     

Atmospheric dry deposition fluxes of trace elements measured in Bursa, Turkey

Trace element dry deposition fluxes were measured using a smooth, greased, knife-edge surrogate surface (KSS) holding greased Mylar strips in Bursa, Turkey. Sampling program was conducted between October 2002 and June 2003 and 46 dry deposition samples were collected. The average fluxes of crustal metals (Mg, Ca, and Fe) were one to four orders of magnitude higher than the fluxes of anthropogenic metals. Trace element fluxes ranged from 3 (Cd) to 24,230 (Ca) microg m(-2) d(-1). The average trace element dry deposition fluxes measured in this study were similar to those measured in other urban areas. In addition, ambient air samples were also collected simultaneously with flux samples and concentrations of trace elements, collected with a TSP sampler, were between 0.7 and 4900 ng m(-3) for Cd and Ca, respectively. The overall trace element dry deposition velocities, calculated by dividing the fluxes to the particle phase concentrations ranged from 2.3+/-1.7 cm s(-1) (Pb) to 11.1+/-6.4 cm s(-1) (Ni). These values are in good agreement with the values calculated using similar techniques. The anthropogenic and crustal contributions were estimated by employing enrichment factors (EFs) calculated relative to the average crustal composition. Low EFs for dry deposition samples were calculated. This is probably due to contamination of local dust and its important contribution to the collected samples.     

A Transition-Flow Reactor Tube for Measuring Trace Gas Concentrations

Dry deposition contributes significantly to the acidification of ecosystems. However, difficulties in measuring dry deposition of reactive gases and fine particles make routine direct monitoring impractical. An alternate approach is to use the “concentration monitoring” method in which dry deposition flux is estimated as the product of measured concentration and estimated deposition velocity. A sampling system that performs over the period of 6 hours to 7 days, depending on atmospheric concentrations, has been developed. It consists of a Teflon cyclone to exclude particles larger than about 2 μm, selective solid adsorption media for reactive gases—some of which are sampled from a transition flow to avoid possible bias from particle evaporation, a particle filter, and a final gas adsorption filter to collect the remaining trace gas. The sampler Is the first reported application of transition flow mass transfer for the collection and quantitative measurement of trace atmospheric gases. Laboratory and field tests have shown that the sampler performs well for HNO₃(g).     

Dry deposition of particles and canopy exchange: Comparison of wet,bulk and throughfall deposition at five forest sites in Italy

The contribution of dry deposition to the total atmospheric input of acidifying compounds and base cations is of overwhelming importance. Throughfall measurements provide an estimate of the total deposition to forest soils, including dry deposition, but some uncertainties, related to the canopy interaction processes, affect this approach. We compared the concentrations and the fluxes of the main ions determined in wet-only, bulk and throughfall samples collected at five forest sites in Italy. The contribution of coarse particles deposited onto the bulk samplers was of prime importance for base cations, representing on average from 16% to 46% of the bulk deposition. The extent of this dry deposition depended on some geographical features of the sites, such as the distance from the sea and the annual rainfall. The possibility of applying specific bulk/wet ratios to estimate the wet deposition proved to be limited by the temporal variability of these ratios, which must be considered together with the spatial variability. A direct comparison of the dry contribution deriving from the bulk–wet and the throughfall–wet demonstrated that an extensive natural surface (forest canopy) performs better than a small synthetic surface (funnel of the bulk sampler) in collecting dry deposition of SO₄²⁻, NO₃⁻ and Na⁺. The canopy exchange model was applied to both bulk and wet data to estimate the contribution of dry deposition to the total input of base cations, and the uncertainty associated to the model discussed. The exclusive use of bulk data led to a considerable underestimation of base cation dry deposition, which varies among the study sites.     

Dry deposition (downward, upward) concentration study of particulates and heavy metals during daytime, nighttime period at the traffic sampling site of Sha-Lu, Taiwan

Downward, upward dry deposition fluxes and total suspended particulate of particulate heavy metals (Fe, Pb, Zn, Cu, Mg and Mn) were measured in daytime and nighttime period in Sha-Lu, a small city in the central Taiwan during summer period of 2003. The results showed that the total suspended particulate concentrations of particulate mass in the daytime period (averaged 996.2 g/m3) were higher than in nighttime period (averaged 560.7 g/m3). And the downward dry deposition fluxes (averaged 54.07 g/m2s) were about two times as that of upward dry deposition fluxes (averaged 26.48 g/m2s) in the daytime period. Furthermore, the average downward dry deposition fluxes (averaged 26.22 g/m2s) were also about two times as that of upward dry deposition fluxes (averaged 12.11 g/m2s) in the nighttime period. In addition, the average downward dry deposition fluxes are greater than the upward dry deposition fluxes for all the heavy metals in either daytime or nighttime period. The proposed reasons are that the wind speed and concentration difference for daytime and nighttime period lead to these results at the traffic sampling site of central Taiwan. In addition, the deposition velocity for mass, heavy metals (Fe, Pb, Zn, Cu, Mg and Mn) during daytime and nighttime period were also calculated. The average daytime dry deposition velocity for downward particulate mass, upward particulate mass, Fe, Pb, Zn, Cu, Mg and Mn were 5.56, 2.66, 1.71, 0.18, 1.06, 0.24, 0.47 and 0.11 (cm/s), respectively. And the average nighttime dry deposition velocity for downward particulate mass, upward particulate mass, Fe, Pb, Zn, Cu, Mg and Mn were 4.70, 2.11, 1.66, 0.18, 0.86, 0.23, 0.32 and 0.07 (cm/s), respectively at traffic sampling site of central Taiwan.     

Study of particulates and metallic elements at a farm sampling site in central Taiwan

The total suspended particle (TSP) concentration, dry deposition and wind speed were measured with a PS-1 sampler, a dry deposition plate and a Weather Monitor II (#7440), respectively, at the Experimental Farm of Thunghai University in Taiwan. Taiching Industrial Park, Taichung Cong Road (traffic) and a hospital incinerator are close to the sampling site. The sampling time was from August 2001 to December 2001. The average dry deposition flux, the TSP concentration, dry deposition velocities, average wind speed and maximum wind speed were recorded as 617.7 ± 281.4 mg/day/m2, 117.5 ± 17.6 μg/m3, 5.9 ± 2.2 cm/s, 2.7 ± 1.3 m/s and 7.6 ± 2.3 m/s, respectively, at this sampling site. Good correlation coefficients (R) of the TSP concentration and the dry deposition flux with wind speed were found, with values of 0.46 and 0.50, respectively. The concentrations and dry deposition of the total metallic elements were also obtained. The results indicated that the concentrations of anthropogenic elements (Pb, Mn, Cd, Ni, Cr and Zn) were mostly higher than those obtained in other studies around the world. The average dry deposition fluxes and TSP concentrations for Zn and Pb were 0.45 and 0.42, respectively. The same phenomenon was also observed for Fe and Mg (R = 0.59 and 0.65). The results indicate that these elements were all coming from the same emission sources at the farm sampling site.     

Interactions between precipitation and Scots pine canopies along a heavy-metal pollution gradient

Bulk precipitation and stand throughfall were collected during 1992-96 at distances of 0.5, 4 and 8 km from the Harjavalta Cu-Ni smelter, southwestern Finland. The amounts of heavy metals (Cu, Ni, Zn, Fe) and mineral nutrients in bulk precipitation and throughfall were highest at 0.5 km. Although the canopy coverage was low at 0.5 km, the amounts of heavy metals intercepted by the canopy were extremely high. The proportion of foliar leaching relative to the wash-off of dry deposition from the needle surfaces decreased on moving towards the smelter for all elements, except for K. The high rate of K leaching from the needle tissues close to the smelter demonstrated that the K throughfall flux has been greatly altered by the heavy pollution load.     

Application of capillary electrophoresis combined with a modified BCR sequential extraction for estimating of distribution of selected trace metals in PM2.5 fractions of urban airborne particulate matter

The capillary electrophoresis (CE) method combined with a sequential extraction was applied to determine the distribution of Fe, Zn, Cu, Mn and Cd in urban ambient air PM2.5 samples. PM2.5 was collected on Teflon filters with dichotomous sampler, and the modified extraction procedure following the BCR leaching procedure was used to chemically fractionate metals into "easily exchangeable" with water, "acid extractable" with 0.11 mol/l acetic acid, "reducible" with 0.1 mol/l hydroxylamine hydrochloride acidified to pH 2.0 with nitric acid, and "oxidisable" with oxidation by 8.8 mol/l hydrogen peroxide (H2O2) followed by extraction with 1.0 mol/l ammonium acetate. Based on the obtained results it was concluded that the application of the studied methodology provides chemical fractionation data that reflect the general sources and potential health hazards of the studied metals.     

Trace metal contents in Parmelia caperata (L.) Ach. compared to bulk deposition,throughfall and leaf-wash fluxes in two holm oak forests in Montseny (NE Spain)

The metal concentrations of V, Cr, Co, Ni, Cu, Zn, Cd, Hg and Pb were analysed in distilled water extracts of Parmelia caperata and in bulk deposition, throughfall and an experimental in situ washing of leaves at two forests at Montseny (NE Spain) submitted to differential exposure to the industrial and traffic activities around Barcelona. Lichen concentrations of Zn, Cu, V, and Cd were higher at the site of greater exposure to pollutants. Consistently, there was higher dry deposition of these metals at the more exposed site. The order of abundance of trace metals in the lichen was similar to that in the deposition variables, although Pb and Cu had intermediate concentrations in the lichen but were very low in the deposition measurements. This indicated the higher affinity of Pb and Cu for the exchange sites in the lichen cell wall and the fact that lichens accumulated Pb for the last 12–18 y when emissions were much higher than today. The ability of Parmelia caperata to indicate the deposition of heavy metals, together with its easy sampling and handling, its broad distribution and its easy identification suggest that the lichen extract procedure described here could be used to establish gradients of atmospheric deposition of heavy metals at a general geographic level.     

Element concentrations in the forest moss Hylocomium splendens: variation associated with altitude, net primary production and soil chemistry.

Net primary production (NPP) of the forest moss Hylocomium splendens increased significantly along an elevational gradient in the southern Alps of Italy. Extracellularly bound metals (Al, Ca, Co, Cr, Fe, Ni, Mo, Ni, Pb) showed declining concentrations in moss tissue with increasing altitude, presumably because the amount of exchange sites on the cell wall increases less than total biomass. Concentrations of intracellular elements did not vary (Cd, Cu, Mg, Na, Zn), or even increased (K) with altitude. The observed patterns were always independent of precipitation amount and soil concentrations of exchangeable elements. A higher soil nutrient status only enhanced K uptake by the moss. We concluded that variations in moss NPP, associated with elevational gradients, may significantly affect estimates of atmospheric deposition based on moss analysis in mountainous regions.     

The function of digestive enzymes on Cu, Zn, and Pb release from soil in in vitro digestion tests

The bioaccessibility of soil heavy metals is the solubility of soil heavy metals in synthetic human digestive juice, which is usually determined using in vitro digestion test. To reveal the effects of digestive enzymes on soil heavy metals bioaccessibility, three representative in vitro digestion tests, Simple Bioaccessibility Extraction Test (SBET), Physiologically Based Extraction Test (PBET), and Simple Gastrointestinal Extraction Test (SGET), were chosen. The bioaccessibility of soil Cu, Zn, and Pb in each method were respectively evaluated with and without digestive enzymes, and the differences were compared. The results showed that the effects of digestive enzymes varied with different methods and elements. Because of digestive enzymes addition, the environmental change from acid gastric phase to neutral intestinal phase of PBET did not result in apparently decrease of the bioaccessibility of soil Cu. However, the solubility of soil Zn and Pb were pH-dependent. For SGET, when digestive enzymes were added, its results reflected more variations resulting from soil and element types. The impacts of digestive enzymes on heavy metal dissolution are mostly seen in the intestinal phase. Therefore, digestive enzyme addition is indispensable to the gastrointestinal digestion methods (PBET and SGET), while the pepsin addition is not important for the methods only comprised of gastric digestion (SBET).     

New and Improved Procedures for Gas Sampling and Analysis in the National Air Sampling Network

The NASN sampler for the collection of gaseous pollutants has been modified to increase its versatility and efficiency. Oxides of nitrogen are collected in bubblers employing a 70-100 μ frit with a collection efficiency of approximately 50% depending upon the frit porosity. Included in the sampler is a bubbler for the collection of aldehydes in which the aldehyde-MBTH complex is stable at least two weeks. This inert bubbler, which is constructed of polypropylene and Teflon, makes it possible for samples to be collected over the network and analyzed at a central laboratory. In addition, gaseous ammonia is collected in 0.1N H₂SO₄. This collecting system has an efficiency of greater than 85%. Low-level samples are analyzed automatically employing Nesslerization, whereas high-level samples from source emissions may be collected in indicating boric acid and titrated with 0.02N H₂SO₄. The sampler will accommodate either 50 or 100 ml polypropylene collecting tubes.     

Concentrations and fluxes of organic compounds in the atmosphere of the Swedish west coast

Measurements of organic compounds in air and deposition have been carried out in parallel on the Swedish west coast. In this investigation the importance of long-range transport for the occurrence of organic compounds in deposition has been studied. Air samples were collected using a high volume sampler (HVS) and the deposition was sampled on a 1 m² Teflon-coated horizontal surface with runoff for the precipitation to an adsorbent. The samples were analyzed in order to identify and quantify different semivolatile compounds such as PAH and petrogenic hydrocarbons and chlorinated compounds such as PCB, HCH and HCB. Qualitative differences between the content of organic compounds in air and deposition during periods with varying levels of air pollution and different meteorological conditions have been studied and a comparison with other air pollutants, such as soot, has been carried out. The results of the measurements show that deposition of PAH and other hydrocarbons takes place continuously but the greatest amounts are measured in the deposition in connection with episodes together with heavy precipitation. The highest concentrations of PCB and HCH in the air were obtained during a warm dry period in May and the greatest amounts were deposited in a period in May with heavy precipitation.     

pH值对烧结砖中重金属释放的影响

采用酸消解实验和NEN 7371浸出实验研究了烧结砖中重金属总量和有效释放量,采用pH-dependence实验研究pH对破碎烧结砖样品中重金属(Cr、Ni、As、Cd和Pb)浸出特性的影响,以及烧结砖样品的酸碱缓冲容量。结果表明,烧结砖中重金属的有效释放量低于总量,释放率从大到小依次为CdAsPbNiCr;烧结砖的酸缓冲容量较小,浸出液pH从7.03降到3.64,消耗了29.33 mmol/kg硝酸,碱缓冲容量较大,pH从7.03升到12.40,共消耗256 mmol/kg氢氧化钠溶液,因此在使用烧结砖的过程中要特别注意环境pH;浸提液的酸碱性是影响烧结砖中重金属浸出的重要参数,在实验研究的pH范围内,不同重金属的浸出规律不同。Cr和As的释放受pH影响较小,而Ni和Cd的浸出量随pH的增大而降低,Pb的浸出量在强酸和强碱条件下均较大,当pH在5.59~9.86的范围内浸出量很低。     

水泥对垃圾焚烧飞灰的固化处理试验研究

对垃圾焚烧飞灰的化学成分、重金属物质的含量及浸出浓度进行测试分析.结果表明,飞灰中Pb和Cr等重金属物质浸出量超过浸出毒性标准,因而被认为是危险废物,必须进行固化处理.还考察了水泥对焚烧飞灰中重金属物质固化的效果,研究表明当飞灰掺量适当时,重金属物质的固化效果良好.重金属物质通过物理固封、替代,沉淀反应和吸附等形式可固化进水泥水化产物结构中.     

Investigation of filtration artifacts when sampling ambient particulate matter for mutagen assay

An ultra-high volume ambient particulate sampler capable of collecting four identical samples was used to investigate filtration artifacts which may affect mutagen assays. During five sampling episodes variables employed included filter material (glass, quartz, Teflon and Teflon-impregnated glass fiber), sampling interval (3–12 h) and the re-exposure to varying concentrations of gaseous pollutants. Filters were extracted with an equi-volume mixture of dichloromethane, toluene and methanol and extracts subjected to Salmonella /mammalian microsome mutagenicity testing employing strain TA98. From this somewhat limited data set, no large differences were observed which could be attributed to filtration artifacts.     

Dynamic studies on the mobility of trace elements in soil and sediment samples influenced by dumping of residues of the flood in the Mulde River region in 2002

In the analysis of soil samples, batch sequential extraction procedures are traditionally used for the fractionation of trace elements to access their mobility and potential risk for the contamination of groundwater. In the present work a continuous-flow technique has been used that enables not only the fast and efficient leaching of trace elements but as well as time-resolved studies on the mobilization of arsenic and selected heavy metals in different forms to be made. Rotating coiled columns (RCC) earlier used mainly in countercurrent chromatography have been successfully applied to the dynamic leaching of heavy metals from soils contaminated by flooding sludge's. The sample was retained in a PTFE rotating column as the stationary phase whereas aqueous solutions were continuously pumped through. The contents of elements were determined by on-line coupling of RCC and inductively coupled plasma atomic emission spectrometry (ICP-AES). This enables real-time data on the leaching process to be obtained. Dynamic and traditional batch procedures were compared. It has been shown that the aqueous elution under centrifugal forced conditions is much more effective for the mobilization of heavy metals. Hence, the dynamic leaching is characterized by a substantially more intensive interaction between solid and water and is besides substantially more time-saving than the conventional batch procedure. The RCC procedure was also employed for preliminary leaching studies with a simulated "acid rain". In comparison with the water leaching, the mobilization of heavy metals and arsenic from soil samples with employment of simulated acid rain as eluent was less effective.     

A new sampler for collecting separate dry and wet atmospheric depositions of trace organic chemicals

Studies conducted in Saskatchewan and elsewhere have demonstrated the atmospheric transport of agricultural pesticides and other organic contaminants and their deposition into aquatic ecosystems. To date these studies have focused on ambient concentrations in the atmosphere and in wet precipitation. To measure the dry deposition of organic chemicals, a new sampler was designed which uses a moving sheet of water to passively trap dry particles and gasses. The moving sheet of water drains into a reservoir and, during recirculation through the sampler, is passed through an XAD-2 resin column which adsorbs the trapped organic contaminants. All surfaces which contact the process water are stainless steel or Teflon. Chemicals collected can be related to airborne materials depositing into aquatic ecosystems. The sampler has received a United States patent (number 5,413,003 – 9 May 1996) with the Canadian patent pending.XAD-2 resin adsorption efficiencies for 10 or 50 μg fortifications of ten pesticides ranged from 76% for atrazine (2-chloro-4-ethylamino-6-isopropylamino-S-triazine) to 110% for triallate [S-(2,3,3-trichloro-2-phenyl)bis(1-methylethyl)carbamothioate], dicamba (2-methoxy-3,6-dichlorobenzoic acid) and toxaphene (chlorinated camphene mixture). Field testing using duplicate samplers showed good reproducibility and amounts trapped were consistent with those from high volume and bulk pan samplers located on the same site. Average atmospheric dry deposition rates of three chemicals, collected for 5 weeks in May and June, were: dicamba, 69 ng m^-2 da^-1; 2,4-D (2,4-dichlorophenoxyacetic acid), 276 ng m^-2 da^-1: and, γ-HCH (γ-1, 2, 3, 4, 5, 6-hexachlorocyclohexane), 327 ng m^-2 da^-1.