World data centre for greenhouse gases

News And Comments

World data centre for greenhouse gases     

Market-based mechanisms for controlling global emissions of greenhouse gases

Increasing worldwide concern about global warming has led to intensified international efforts to reduce emissions of greenhouse gases. The most important outcome of these efforts is the United Nations Framework Convention on Climate Change, which came into force in March 1994. Although its signatories are expected to draw up plans to curb greenhouse gas emissions, the Convention does not specify how these emissions should be controlled. Since market-based mechanisms for emissions control have been increasingly emphasized at both national and international levels, this paper discusses both their advantages over regulation and the main obstacles to their implementation. The ultimate aim of the paper is to propose possible baseline criteria for the formulation of a global tradable permit system to control carbon dioxide emissions .     

Emission of the greenhouse gases nitrous oxide and methane from constructed wetlands in europe

The potential atmospheric impact of constructed wetlands (CWs) should be examined as there is a worldwide increase in the development of these systems. Fluxes of N(2)O, CH(4), and CO(2) have been measured from CWs in Estonia, Finland, Norway, and Poland during winter and summer in horizontal and vertical subsurface flow (HSSF and VSSF), free surface water (FSW), and overland and groundwater flow (OGF) wetlands. The fluxes of N(2)O-N, CH(4)-C, and CO(2)-C ranged from -2.1 to 1000, -32 to 38 000, and -840 to 93 000 mg m(-2) d(-1), respectively. Emissions of N(2)O and CH(4) were significantly higher during summer than during winter. The VSSF wetlands had the highest fluxes of N(2)O during both summer and winter. Methane emissions were highest from the FSW wetlands during wintertime. In the HSSF wetlands, the emissions of N(2)O and CH(4) were in general highest in the inlet section. The vegetated ponds in the FSW wetlands released more N(2)O than the nonvegetated ponds. The global warming potential (GWP), summarizing the mean N(2)O and CH(4) emissions, ranged from 5700 to 26000 and 830 to 5100 mg CO(2) equivalents m(-2) d(-1) for the four CW types in summer and winter, respectively. The wintertime GWP was 8.5 to 89.5% of the corresponding summertime GWP, which highlights the importance of the cold season in the annual greenhouse gas release from north temperate and boreal CWs. However, due to their generally small area North European CWs were suggested to represent only a minor source for atmospheric N(2)O and CH(4).     

Changing places, changing emissions: The cross-scale reliability of greenhouse gas emission inventories in the US

Greenhouse gas (GHG) emission inventories, which currently inform abatement policy discussions, are developed mostly from national scale data. Nevertheless, although the policy debate tends to take place in global and national arenas, action to abate GHG emissions is inherently within the provenance of local institutions and communities. The purpose of this paper is to examine how much information is lost by not estimating GHG emissions data at scales finer than the whole US. Such information may be critical in bridging global and local policy. Differences in the composition of GHG emission sources based on GHG emission inventories at three nested spatial scales (national, state, local) for four study sites (in Kansas, North Carolina, Ohio and Pennsylvania) are analysed, drawing upon initial results of a large collaborative study known as the 'Association of American Geographers-Global Change in Local Places (GCLP)' project. The concept of spatial sovereignty of emissions is developed to test the cross-scale reliability of emission inventories. For the test year 1990, close agreement is found in the by-gas composition of GHG emissions among national, state and local inventories. Spatial sovereignty in this case is maintained. However close agreement is not found in the by-source composition of GHG emissions among national, state and local inventories. Spatial sovereignty in this case is not maintained. Regular compilation of state and local emissions source inventories may be necessary to track important spatial and temporal deviations from national trends.     

Methods for assessing greenhouse gas mitigation for countries with economies in transition: Summary of workshop presentations and discussions

Environmental Management -     

A quantitative technique for estimating the boundaries of wetlands from vegetation data

There is an increasing need for the accurate delineation of wetlands for planning and conservation purposes. We propose a method based on vegetation zonation which requires three steps. The first step is to examine transects crossing the transition zone from marsh to upland. In each transect the uppermost occurrence of each plant species is located relative to a fixed survey point. The second step is to determine which of these species are hydrophytes (wetland plants). This is assessed using the presence or absence of morphological and physiological adaptations for growing in wet environments. Alternatively, a literature search using botanical manuals may suffice. The third step determines the upper limit of the wetland by finding the upper limit of the uppermost hydrophyte in each transect, and taking the mean value of these over all transects. This mean defines the boundary of the wetland. The method is illustrated using two marshes along the north shore of the St. Lawrence River in Ontario.     

Electric Swing Adsorption for CO2 removal from flue gases

One of the most important sources of CO₂ emissions are the fossil-fuel fired plants for production of electricity. Removal of CO₂ from flue gas streams for further sequestration has been proposed by the International Panel on Climate Change experts as one of the most reliable solutions to mitigate anthropogenic greenhouse emissions. When natural gas is employed as fuel, the molar fraction of CO₂ in the flue gas is lower than 5% causing serious problems for capture. The purpose of this work is to present experimental validation of an Electric Swing Adsorption (ESA) technology that may be employed for carbon capture for low molar fractions of CO₂ in the flue gas streams. To improve energy utilization, an activated carbon honeycomb monolith with low electrical resistivity was employed as selective adsorbent. A mathematical model for this honeycomb is proposed as well as different ESA cycles for CO₂ capture.     

On-line greenhouse gas detection from soils and rock formations

Several on-site studies have been conducted on rock formations and soils where gases were collected into boreholes. The equipment consisted of packers isolating a chamber for gas collection. A pump allows gas transfer towards FT-IR sensors located at the surface. Such analytical approach shows several advantages for gas monitoring in boreholes: it allows variation detection with time of the partial pressure of gases; detection and evolution with time of the concentration of annex gases or markers; application to the injection and post-injection periods to determine possible deviations from a previously recorded baseline; and possible use of several boreholes in networks.     

Local governance of greenhouse gas emissions from air travel

Global greenhouse gas emissions from air travel (GHG-A) are on the rise, and projections point towards a rapid growth in the coming decades. This study aims to examine how local government (cities), addresses GHG-A in their Sustainable Energy Action Plans (SEAP). To fulfil this aim, over 200 SEAPs were analysed focusing on three issues: (1) Treatment of GHG-A in local emissions inventories; (2) Policy initiatives within this domain; and (3) The cities’ perceptions of the conflicts of interests. Results showed that more than half of the cities acknowledge the challenge of GHG-A, around one third include GHG-A in their emissions inventories, and more than one quarter have initiated policy interventions. To categorise these interventions, we have added a mode ‘governing by agenda setting’ to an existing analytical framework, ‘Modes of governing’. With their authority limited to the local setting, this mode of governing is a common channel for cities to push changes at higher levels.     

Global risk, local values?: 'Risk society' and the greenhouse issue in Newcastle, Australia

Global environmental issues have permeated many disciplines over the last decade. Within the social sciences they have sparked a debate about the extent to which any 'ecological crisis' can be seen as symptomatic of deeper changes within modernity. The strength of such an explanation is examined in this paper with reference to the 'risk society' thesis advanced by Ulrich Beck and its applicability to the case of the greenhouse issue in Australia. Australia has received much international criticism for its 'differentiated' approach to the United Nations Framework Convention on Climate Change process. This paper examines how this approach has gained widespread currency within 'official' policy spheres through defining greenhouse risks in terms of the spatial and temporal referents of modernity: the individual; the nation-state; political and investment timetables. The possibility of alternative public understandings of greenhouse risks and responsibilities is examined through recent work undertaken in Newcastle, New South Wales, Australia. It is argued that these may represent very different interpretations of the greenhouse issue from those encountered within the 'official' policy sphere. However, without a greater recognition on the part of policy elites of the need to address an issue like greenhouse at a local scale and through public involvement, and institutions through which to do so, these interpretations will have little impact on the 'global' process of negotiating greenhouse outcomes.     

Assessing representativeness of places for conservation reservation and heritage listing

Problems arising from application of the representative criterion for conservation and natural heritage evaluation are discussed. An ecological basis to this criterion is suggested that focuses on those key environmental factors dominating biotic response. A methodology is proposed that utilizes computer-based methods of establishing and interrogating spatial data bases (geographic information systems), environmental modeling, and numeric analysis. An example is presented illustrating some of the advantages and limitations of classification and dimension reduction techniques in both defining bioenvironments and displaying their spatial distribution. The advantages of this method for representativeness evaluation are that it maximizes the utility of available data, is explicit and repeatable, and enables large areas to be analyzed at relatively fine scales.     

Cattle feedlot soil moisture and manure content: I. Impacts on greenhouse gases, odor compounds, nitrogen losses, and dust

Beef cattle feedlots face serious environmental challenges associated with manure management, including greenhouse gas, odor, NH3, and dust emissions. Conditions affecting emissions are poorly characterized, but likely relate to the variability of feedlot surface moisture and manure contents, which affect microbial processes. Odor compounds, greenhouse gases, nitrogen losses, and dust potential were monitored at six moisture contents (0.11, 0.25, 0.43, 0.67, 1.00, and 1.50 g H2O g(-1) dry matter [DM]) in three artificial feedlot soil mixtures containing 50, 250, and 750 g manure kg(-1) total (manure + soil) DM over a two-week period. Moisture addition produced three microbial metabolisms: inactive, aerobic, and fermentative at low, moderate, and high moisture, respectively. Manure content acted to modulate the effect of moisture and enhanced some microbial processes. Greenhouse gas (CO2, N2O, and CH4) emissions were dynamic at moderate to high moisture. Malodorous volatile fatty acid (VFA) compounds did not accumulate in any treatments, but their persistence and volatility varied depending on pH and aerobic metabolism. Starch was the dominant substrate fueling both aerobic and fermentative metabolism. Nitrogen losses were observed in all metabolically active treatments; however, there was evidence for limited microbial nitrogen uptake. Finally, potential dust production was observed below defined moisture thresholds, which were related to manure content of the soil. Managing feedlot surface moisture within a narrow moisture range (0.2-0.4 g H2O g(-1) DM) and minimizing the accumulation of manure produced the optimum conditions that minimized the environmental impact from cattle feedlot production.     

Assessment of the greenhouse effect impact of technologies used for energy recovery from municipal waste: A case for England

Waste management activities contribute to global greenhouse gas emissions approximately by 4%. In particular the disposal of waste in landfills generates methane that has high global warming potential. Effective mitigation of greenhouse gas emissions is important and could provide environmental benefits and sustainable development, as well as reduce adverse impacts on public health. The European and UK waste policy force sustainable waste management and especially diversion from landfill, through reduction, reuse, recycling and composting, and recovery of value from waste. Energy from waste is a waste management option that could provide diversion from landfill and at the same time save a significant amount of greenhouse gas emissions, since it recovers energy from waste which usually replaces an equivalent amount of energy generated from fossil fuels. Energy from waste is a wide definition and includes technologies such as incineration of waste with energy recovery, or combustion of waste-derived fuels for energy production or advanced thermal treatment of waste with technologies such as gasification and pyrolysis, with energy recovery. The present study assessed the greenhouse gas emission impacts of three technologies that could be used for the treatment of Municipal Solid Waste in order to recover energy from it. These technologies are Mass Burn Incineration with energy recovery, Mechanical Biological Treatment via bio-drying and Mechanical Heat Treatment, which is a relatively new and uninvestigated method, compared to the other two. Mechanical Biological Treatment and Mechanical Heat Treatment can turn Municipal Solid Waste into Solid Recovered Fuel that could be combusted for energy production or replace other fuels in various industrial processes. The analysis showed that performance of these two technologies depends strongly on the final use of the produced fuel and they could produce GHG emissions savings only when there is end market for the fuel. On the other hand Mass Burn Incineration generates greenhouse gas emission savings when it recovers electricity and heat. Moreover the study found that the expected increase on the amount of Municipal Solid Waste treated for energy recovery in England by 2020 could save greenhouse gas emission, if certain Energy from Waste technologies would be applied, under certain conditions.     

Optical properties of intact leaves for estimating chlorophyll concentration

Changes in leaf chlorophyll content can serve as relative indicators of plant vigor and environmental quality. This study identified reflectance, transmittance, and absorptance wavebands and band ratios within the 400- to 850-nm range for intact leaves that could be used to estimate extracted leaf chlorophyll per unit leaf area (areal concentration) with minimal error. Leaf optical properties along with chlorophyll a, b, and a + b concentrations were measured for the planar-leaved sweetgum (Liquidambar styraciflua L.), red maple (Acer rubrum L.), wild grape (Vitis rotundifolia Michx.), and switchcane [Arundinaria gigantea (Walter) Muhl.], and for needles of longleaf pine (Pinus palustris Miller). Generally, reflectance, transmittance, and absorptance corresponded most precisely with chlorophyll concentrations at wavelengths near 700 nm, although regressions were also strong in the 550- to 625-nm range. A power function was superior to a simple linear function in yielding low standard deviations of the estimate (s). When data were combined among the planar-leaved species, s values were low at approximately 50 mumol/m2 out of a 940 mumol/m2 range in chlorophyll a + b at best-fit wavelengths of 707 to 709 nm. Minimal s values for chlorophyll a + b ranged from 32 to 62 mumol/m2 across species when band ratios having numerator wavelengths of 693 to 720 nm were used with the application of a power function. Optimal denominator wavelengths for the band ratios were 850 nm for reflectance and transmittance and 400 nm for absorptance. This information can be applied in designing field portable chlorophyll meters and in the landscape-scale remote sensing of plant responses to the environment.     

Bioethanol from waste: Life cycle estimation of the greenhouse gas saving potential

This paper considers two alternative feedstocks for bioethanol production, both derived from household waste—Refuse Derived Fuel (RDF) and Biodegradable Municipal Waste (BMW). Life Cycle Assessment (LCA) has been carried out to estimate the GHG emissions from bioethanol using these two feedstocks. An integrated waste management system has been considered, taking into account recycling of materials and production of bioethanol in a combined gasification/bio-catalytic process. For the functional unit defined as the ‘total amount of waste treated in the integrated waste management system’, the best option is to produce bioethanol from RDF—this saves up to 196 kg CO₂ equiv. per tonne of MSW, compared to the current waste management practice in the UK.However, if the functional unit is defined as ‘MJ of fuel equiv.’ and bioethanol is compared with petrol on an equivalent energy basis, the results show that bioethanol from RDF offers no saving of GHG emissions compared to petrol. For example, for a typical biogenic carbon content in RDF of around 60%, the life cycle GHG emissions from bioethanol are 87 g CO₂ equiv./MJ while for petrol they are 85 g CO₂ equiv./MJ. On the other hand, bioethanol from BMW offers a significant GHG saving potential over petrol. For a biogenic carbon content of 95%, the life cycle GHG emissions from bioethanol are 6.1 g CO₂ equiv./MJ which represents a saving of 92.5% compared to petrol. In comparison, bioethanol from UK wheat saves 28% of GHG while that from Brazilian sugar cane – the best performing bioethanol with respect to GHG emissions – saves 70%. If the biogenic carbon of the BMW feedstock exceeds 97%, the bioethanol system becomes a carbon sequester. For instance, if waste paper with the biogenic carbon content of almost 100% and a calorific value of 18 MJ/kg is converted into bioethanol, a saving of 107% compared to petrol could be achieved. Compared to paper recycling, converting waste paper into bioethanol saves 460 kg CO₂ equiv./t waste paper or eight times more than recycling.     

Degradation of greenhouse twines derived from natural fibers and biodegradable polymer during composting

Commercial composting operations generally do not accept organic wastes with plastic twines from the greenhouse vegetable industry and the bulk of the waste materials ends up in landfills. The objectives of this paper are to identify environmentally compatible substitutes that could replace the current use of petrochemically derived plastic twines in greenhouse vegetable production, thus diverting them from landfills, and to assess the extent of their degradation via composting. Physical properties of the twines, including linear density, percent weight loss and tensile strength were monitored for the biodegradation tests. A pilot-scale composting trial was conducted in an in-vessel composting system. Results showed that the three biodegradable twine materials (cotton, jute and EcoPLA) could degrade readily in a composting environment within a reasonable time frame. Specifically, at the end of 105 days of composting, 85.3%, 84.8% and 81.1% of weight loss was observed for cotton, jute and EcoPLA, respectively. Furthermore, EcoPLA exhibited a slower decline in tensile strength with time, when compared to jute and cotton.     

Partnerships for local sustainability and local governance in a Tasmanian settlement

This research is concerned with effects and actions at the local level, where it is argued that local governing processes are key to developing sustainable communities. The roles of the citizen and of formal government are changing such that the implementation of sustainability praxis at the local level requires that citizens and governments reconsider both the meaning and techniques of governance. Indeed, how we are governed, participate in governing processes and internalise and accept the need for change will affect how local communities make constant and lasting a dynamic praxis of sustainability. Actors in local governments and communities may be crucial in this task—especially as facilitators, enablers, leaders and partners. In this paper we focus on the Huon Valley Council and some members of one of its communities. We examine how they are experimenting with partnerships as a form of governance to unify, control, mobilise and regulate the conduct of various actors, and how such partnerships may foster sustainability praxis in the Valley's diverse communities of place and interest.     

Partnerships for local sustainability and local governance in a Tasmanian settlement

This research is concerned with effects and actions at the local level, where it is argued that local governing processes are key to developing sustainable communities. The roles of the citizen and of formal government are changing such that the implementation of sustainability praxis at the local level requires that citizens and governments reconsider both the meaning and techniques of governance. Indeed, how we are governed, participate in governing processes and internalise and accept the need for change will affect how local communities make constant and lasting a dynamic praxis of sustainability. Actors in local governments and communities may be crucial in this task—especially as facilitators, enablers, leaders and partners. In this paper we focus on the Huon Valley Council and some members of one of its communities. We examine how they are experimenting with partnerships as a form of governance to unify, control, mobilise and regulate the conduct of various actors, and how such partnerships may foster sustainability praxis in the Valley's diverse communities of place and interest.