A novel field measurement method for determining fine particle and gas emissions from residential wood combustion

Emission data from residential wood combustion are usually obtained on test stands in the laboratory but these measurements do not correspond to the operational conditions in the field because of the technological boundary conditions (e.g. testing protocol, environmental and draught conditions). The field measurements take into account the habitual practice of the operators and provide the more reliable results needed for emission inventories. In this study, a workable and compact method for measuring emissions from residential wood combustion in winter conditions was developed. The emissions for fine particle, gaseous and PAH compounds as well as particle composition in real operational conditions were measured from seven different appliances. The measurement technique worked well and was evidently suitable for winter conditions. It was easy and fast to use, and no construction scaffold was needed. The dilution of the sample with the combination of a porous tube diluter and an ejector diluter was well suited to field measurement. The results indicate that the emissions of total volatile organic carbon (TVOC) (17 g kg⁻¹ (of dry wood burned)), carbon monoxide (CO) (120 g kg⁻¹) and fine particle mass (PM₁) (2.7 g kg⁻¹) from the sauna stove were higher than in the other measured appliances. In the masonry heaters, baking oven and stove, the emissions were 2.9–9 g kg⁻¹ TVOC, 28–68 g kg⁻¹ CO and 0.6–1.6 g kg⁻¹ PM₁. The emission of 12 PAHs (PAH₁₂) from the sauna stove was 164 mg kg⁻¹ and consisted mainly of PAHs with four benzene rings in their structure. PAH₁₂ emission from other appliances was, on average, 21 mg kg⁻¹ and was dominated by 2-ring PAHs. These results indicate that despite the non-optimal operational practices in the field, the emissions did not differ markedly from the laboratory measurements.     

Sorption of polar and nonpolar organic contaminants by oil-contaminated soil

Sorption of nonpolar (phenanthrene and butylate) and polar (atrazine and diuron) organic chemicals to oil-contaminated soil was examined to investigate oil effects on sorption of organic chemicals and to derive oil–water distribution coefficients (K_oil). The resulting oil-contaminated soil–water distribution coefficients (K_d) for phenanthrene demonstrated sorption-enhancing effects at both lower and higher oil concentrations (C_oil) but sorption-reducing (competitive) effects at intermediate C_oil (approximately 1 g kg⁻¹). Rationalization of the different dominant effects was attempted in terms of the relative aliphatic carbon content which determines the accessibility of the aromatic cores to phenanthrene. Little or no competitive effect occurred for butylate because its sorption was dominated by partitioning. For atrazine and diuron, the changes in K_d at C_oil above approximately 1 g kg⁻¹ were negligible, indicating that the presently investigated oil has little or no effect on the two tested compounds even though the polarity of the oil is much less than soil organic matter (SOM). Therefore, specific interactions with the active groups (aromatic and polar domains) are dominantly responsible for the sorption of polar sorbates, and thus their sorption is controlled by available sorption sites. This study showed that the oil has the potential to be a dominant sorptive phase for nonpolar pollutants when compared to SOM, but hardly so for polar compounds. The results may aid in a better understanding of the role of the aliphatic and aromatic domains in sorption of nonpolar and polar organic pollutants.     

Removal of aqueous lead by poorly-crystalline hydroxyapatites

The use of a phosphorus amendment in altering Pb to a chemically less mobile phase is a promising strategy based on minimizing ecotoxicological risk and improving time and cost efficiency. This study evaluated crystalline and poorly-crystalline hydroxyapatite sorbents on removal of aqueous Pb in response to reaction time, solution pH, and Pb concentration. Batch experiments were conducted using a commercially-available crystalline hydroxyapatite (HA), and two poorly-crystalline hydroxyapatites synthesized from gypsum waste (CHA) and incinerated ash of poultry waste (MHA). Poorly-crystalline hydroxyapatites had greater capacity for Pb removal from a solution with a wider pH range as compared to a crystalline hydroxyapatite. The maximum sorption capacity of Pb determined by the Langmuir model was 500 mg g⁻¹ for CHA, 277 mg g⁻¹ for MHA and 145 mg g⁻¹ for HA. Removal of aqueous Pb by CHA was not dependent on solution pH, with a 98.8% reduction throughout the solution pH range of 2–9, whereas aqueous Pb removal by HA and MHA was pH-dependent with less removal in the neutral solution pH. Poorly-crystalline hydroxyapatites may provide an effective alternative to existing remediation technologies for Pb-contaminated sites.     

Biota-sediment metal accumulation and human health risk assessment of freshwater bivalve Corbicula fluminea in Dongting Lake,China

In this study, we analyzed the concentrations of metals in sediments and Corbicula fluminea in China’s Dongting Lake to assess the suitability of C. fluminea as an effective biomonitor of metal contamination in sediments and food safety. We analyzed the biota-accumulation capacity by calculating the biota-sediment accumulation factor (BSAF) and assessed the potential human health risk of metals exposure via consumption of C. fluminea using the target hazard quotient (THQ) and total target hazard quotient (TTHQ). The results showed that the average concentrations of As (31.93 mg kg⁻¹), Cd (5.54 mg kg⁻¹), Cr (105.50 mg kg⁻¹), Cu (32.53 mg kg⁻¹), and Zn (207.89 mg kg⁻¹) in sediments were higher than their respective standard set by the General Administration of Quality Supervision, Inspection and Quarantine of the People’s Republic of China. The sediment metals, which were mainly anthropogenic in origin, were at high levels and pose a relatively high ecological risk. Cadium (Cd) showed very high potential ecological risk levels and should be included in the prior pollutants list in the studied area. The mean levels of As (0.81 mg kg⁻¹) in C. fluminea were 1.62-times higher than that set by the National Health Commission of the People’s Republic of China. BSAF values of the soft tissues of C. fluminea were between 0.05 and 2.14, with higher values for Cu (2.14), Cd (1.77), Zn (1.60), and Ni (1.27). Soft tissues of C. fluminea were able to reflect spatial differences in Sr within sediments around Dongting Lake. The results indicated that C. fluminea could be an potential biomonitor for sediment metals assessment in biomonitoring programs, especially for Cu, Cd, Zn, Ni, and Sr. The mean values for THQ and TTHQ of all the analyzed metals were below 1.0, indicating that the intake of metals via comsumption of C. fluminea does not result in an appreciable risk to human health.

     

Sorption nonequilibrium during solute transport

The effects of pore-water velocity, solute hydrophobicity, and sorbent organic-carbon content on sorption nonequilibrium during solute transport were evaluated. Nonequilibrium transport was observed to increase with pore-water velocity, solute hydrophobicity, and sorbent organic-carbon content. Nonequilibrium transport of neutral organic compounds was not detected with low organic-carbon (TOC = 0.33 g kg⁻¹) aquifer material, but was detected on higher organic sorbents from the unsaturated zone (TOC = 2.6 g kg⁻¹) and the soil surface (TOC = 6.9 g kg⁻¹). For solute-sorbent combinations yielding retardation factors > 2, nonequilibrium during transport was observed. After experimentally accounting for slow solute diffusion in the aqueous phase and isotherm nonlinearity as potential contributors to nonequilibrium solute transport, sorption nonequilibrium was attributed to slow solute diffusion within the organic-carbon matrix.     

Trace elements in aerosol and precipitation at New Castle,NH, USA

Concentrations of a suite of trace elements (Al, Ag, As, Cd, Co, Cr, Cu, Fe, Ni, Pb, Sr, V, Zn) were measured in aerosol and precipitation samples collected at a coastal site in New Castle, NH, from August 1996, through July 1997. Metal concentrations in aerosol and precipitation exhibit a high degree of temporal variability over the annual cycle, varying by approximately one order of magnitude or less for aerosol metals and by ∼2–3 orders of magnitude in precipitation. Estimates of the total annual atmospheric deposition of metals to the Gulf of Maine range from ∼10³ kg yr⁻¹ for Ag, ∼10⁴–10⁵ kg yr⁻¹ for the majority of metals, and ∼10⁶ kg yr⁻¹ for the crustal elements Al and Fe.     

Influence of humified organic matter on copper behavior in acid polluted soils

The main purpose of this work was to identify the role of soil humic acids (HAs) in controlling the behavior of Cu(II) in vineyard soils by exploring the relationship between the chemical and binding properties of HA fractions and those of soil as a whole. The study was conducted on soils with a sandy loam texture, pH 4.3-5.0, a carbon content of 12.4-41.0 g kg⁻¹ and Cu concentrations from 11 to 666 mg kg⁻¹. The metal complexing capacity of HA extracts obtained from the soils ranged from 0.69 to 1.02 mol kg⁻¹, and the stability constants for the metal ion-HA complexes formed, log K, from 5.07 to 5.36. Organic matter-quality related characteristics had little influence on Cu adsorption in acid soils, especially if compared with pH, the degree of Cu saturation and the amount of soil organic matter.     

Emission factors of PAHs,methoxyphenols, levoglucosan,elemental carbon and organic carbon from simulated wheat and Kentucky bluegrass stubble burns

Emission factors (EFs) of pollutants from post-harvest agricultural burning are required for predicting downwind impacts of smoke and inventorying emissions. EFs of polycyclic aromatic hydrocarbons (PAH), methoxyphenols (MP), levoglucosan (LG), elemental carbon (EC) and organic carbon (OC) from wheat and Kentucky bluegrass (KBG) stubble burning were quantified in a US EPA test burn facility. The PAH and MP EFs for combined solid+gas phases are 17±8.2 mg kg⁻¹ and 79±36 mg kg⁻¹, respectively, for wheat and 21±15 mg kg⁻¹ and 35±24 mg kg⁻¹, respectively, for KBG. LG, particulate EC and artifact-corrected OC EFs are 150±130 mg kg⁻¹, 0.35±0.16 g kg⁻¹ and 1.9±1.1 g kg⁻¹, respectively, for wheat and 350±510 mg kg⁻¹, 0.63±0.056 g kg⁻¹ and 6.9±0.85 g kg⁻¹, respectively, for KBG. Positive artifacts associated with OC sampling were evaluated and remedied with a two-filter system. EC and OC accounted for almost two-thirds of PM_2.5 mass, while LG accounted for just under 3% of the PM_2.5 mass. Since EFs of these pollutants generally decreased with increasing combustion efficiency (CE), identifying and implementing methods of increasing the CEs of burns would help reduce their emissions from agricultural field burning. PAH, OC and EC EFs are comparable to other similar studies reported in literature. MP EFs appear dependent on the stubble type and are lower than the EFs for hard and softwoods reported in literature, possibly due to the lower lignin content in wheat and KBG.     

Heavy metal distribution in dust from elementary schools in Hermosillo,Sonora, México

The city of Hermosillo, Sonora in northern Mexico was investigated for its heavy metals content. Samples of sedimented dust in roofs from 25 elementary schools were analyzed for their contents of Ni, Cr, Zn, Cd, Co, Ba, V, Pb, Fe and Cu after digestion with nitric acid. The results of the analysis were used to determine spatial distribution and magnitude of heavy metals pollution. The results of this study reveal that heavy metals distribution is different in two areas of the city. The southern area contains higher concentrations of heavy metals than the northcentral area. The mean level of Cd in exterior dust is 5.65 mg kg⁻¹ in the southern area whereas the mean level of Cd is 2.83 mg kg⁻¹ in the northcentral area. Elevated concentrations of Zn (2012 mg kg⁻¹), Pb (101.88 mg kg⁻¹), Cr (38.13 mg kg⁻¹) and Cd (28.38 mg kg⁻¹) in roof dust were found in samples located near industrial areas. Principal component analysis (PCA) was applied to the data matrix to evaluate the analytical results and to identify the possible pollution sources of metals. PCA shows two main sources: (1) Pb, Cd, Cr and Zn are mainly derived from industrial sources, combined with traffic sources; (2) Fe, Co and Ba are mainly derived from natural sources. V and Ni are highly correlated and possibly related to fuel combustion processes. Enrichment factors were calculated, which in turn further confirms the source identification. Ba and Co are dominantly crustal. Anthropogenically added Cd, Pb, Zn and Cr show maximum enrichment relative to the upper continental crustal component. The distribution of the heavy metals in dust does not seem to be controlled only by the topography of the city, but also by the location of the emission sources.     

Active methods of mercury removal from flue gases

Due to its adverse impact on health, as well as its global distribution, long atmospheric lifetime and propensity for deposition in the aquatic environment and in living tissue, the US Environmental Protection Agency (US EPA) has classified mercury and its compounds as a severe air quality threat. Such widespread presence of mercury in the environment originates from both natural and anthropogenic sources. Global anthropogenic emission of mercury is evaluated at 2000 Mg year⁻¹. According to the National Centre for Emissions Management (Pol. KOBiZE) report for 2014, Polish annual mercury emissions amount to approximately 10 Mg. Over 90% of mercury emissions in Poland originate from combustion of coal.

The purpose of this paper was to understand mercury behaviour during sub-bituminous coal and lignite combustion for flue gas purification in terms of reduction of emissions by active methods. The average mercury content in Polish sub-bituminous coal and lignite was 103.7 and 443.5 μg kg⁻¹. The concentration of mercury in flue gases emitted into the atmosphere was 5.3 μg m⁻³ for sub-bituminous coal and 17.5 μg m⁻³ for lignite. The study analysed six low-cost sorbents with the average achieved efficiency of mercury removal from 30.6 to 92.9% for sub-bituminous coal and 22.8 to 80.3% for lignite combustion. Also, the effect of coke dust grain size was examined for mercury sorptive properties. The fine fraction of coke dust (CD) adsorbed within 243–277 μg Hg kg⁻¹, while the largest fraction at only 95 μg Hg kg⁻¹. The CD fraction < 0.063 mm removed almost 92% of mercury during coal combustion, so the concentration of mercury in flue gas decreased from 5.3 to 0.4 μg Hg m⁻³. The same fraction of CD had removed 93% of mercury from lignite flue gas by reducing the concentration of mercury in the flow from 17.6 to 1.2 μg Hg m⁻³. The publication also presents the impact of photochemical oxidation of mercury on the effectiveness of Hg vapour removal during combustion of lignite. After physical oxidation of Hg in the flue gas, its effectiveness has increased twofold.

     

Growth and photosynthetic responses to copper in wild grapevine

The present study evaluates the tolerance and accumulation potential of Vitis vinifera ssp. sylvestris under moderate and high external Cu levels. A greenhouse experiment was conducted in order to investigate the effects of a range of external Cu concentrations (0–23 mmol L⁻¹) on growth and photosynthetic performance by measuring gas exchange, chlorophyll fluorescence parameters and photosynthetic pigments. We also measured the total copper, nitrogen, phosphorus, sulphur, calcium, magnesium, iron, potassium and sodium concentrations in the plant tissues. All the experimental plants survived even with external Cu concentrations as high as 23 mmol L⁻¹ (1500 mg Cu L⁻¹), although the excess of metal resulted in a biomass reduction of 35%. The effects of Cu on growth were linked to a reduction in net photosynthesis, which may be related to the effect of the high concentration of the metal on photosynthetic electron transport. V. vinifera ssp. sylvestris survived with leaf Cu concentrations as high as 80 mg kg⁻¹ DW and growth parameters were unaffected by leaf tissue concentrations of 35 mg Cu kg⁻¹ DW. The results of our study indicate that plants of V. vinifera ssp. sylvestris from the studied population are more tolerant to Cu than the commercial varieties of grapevine that have been studied in the literature, and could constitute a basis for the genetic improvement of Cu tolerance in grapevine.     

Natural radioactivity levels in soil samples from some areas of Himachal Pradesh,India using γ-ray spectrometry

²²⁶Ra, ²³²Th and ⁴⁰K analysis has been carried out in soil samples collected from some areas of Himachal Pradesh, India using γ-ray spectrometry. The measured activity in soil ranges from 42.09 to 79.63 Bq kg⁻¹, 52.83 to 105.81 Bq kg⁻¹ and 95.33 to 160.30 Bq kg⁻¹ for ²²⁶Ra, ²³²Th and ⁴⁰K with the mean values of 57.34, 82.22 and 135.75 Bq kg⁻¹, respectively. The measured activity concentration of ²²⁶Ra and ²³²Th in soil samples collected from these areas is higher and for ⁴⁰K is lower than the world average. The radium equivalent activity in all the soil samples is lower than the safe limit set in the OECD report (370 Bq kg⁻¹). The value of the external exposure dose has been determined from the content of these radionuclides in soil. It has been observed that on the average, the outdoor terrestrial gamma air absorbed dose rate is about 83.28 nGy h⁻¹. The study yields an annual effective dose in the range of 0.07–0.13 mSv. The average value of annual effective dose lies in the global range of outdoor radiation exposure given in United Nations Scientific Committee on the Effects of Atomic Radiation (UNSCEAR) [(2000). Effects and risks of ionizing radiations. UN, NY]. The activity concentration of ²³⁸U has also been determined using fission track technique and the values range from 3.26 to 7.71 mg kg⁻¹ with a mean value of 4.38 mg kg⁻¹.     

Effect of humic acids on physicochemical property and Cd(II) sorption of multiwalled carbon nanotubes

Carbon nanotubes (CNTs), as a type of superior adsorbents for both organic and inorganic contaminants, are increasingly introduced into the environment. Ubiquitous natural organic matter (NOM) would coat on the released CNTs and change their physicochemical properties and sorption of contaminants. The effects of four sequentially extracted humic acids (HAs, as a model NOM) from a peat soil on the physicochemical properties and Cd(II) sorption of three multiwalled CNTs (MWNTs) with different surface areas were investigated. The MWNTs as purchased with very few oxygen-containing functional groups had relatively low sorption capacities (0.93–1.49 mg g⁻¹) for Cd(II) and the sorption capacity increased with increasing surface area of the MWNTs. Surface-coating with the HAs lowered surface areas of the MWNTs but greatly increased their sorption capacities (5.42–18.4 mg g⁻¹). The MWNT-bound HAs introduced oxygen-containing functional groups and negative charges to the MWNT surfaces, which could thus increase the apparent sorption of Cd(II) through chemical complexation and electrostatic attraction, respectively. The later-extracted HAs with lower polarity were more favorable for the surface-coating but increased less Cd(II) sorption by the MWNTs. The results are expected to shed light on understanding the underlying mechanism of the effect of NOM on the sorption of heavy metal ions by CNTs.     

Potential and drawbacks of EDDS-enhanced phytoextraction of copper from contaminated soils

Incubation and pot experiments using poplar (Populus nigra L. cv. Wolterson) were performed in order to evaluate the questionable efficiency of EDDS-enhanced phytoextraction of Cu from contaminated soils. Despite the promising conditions of the experiment (low contamination of soils with a single metal with a high affinity for EDDS, metal tolerant poplar species capable of producing high biomass yields, root colonization by mycorrhizal fungi), the phytoextraction efficiency was not sufficient. The EDDS concentrations used in this study (3 and 6 mmol kg⁻¹) enhanced the mobility (up to a 100-fold increase) and plant uptake of Cu (up to a 65-fold increase). However, despite EDDS degradation and the competition of Fe and Al for the chelant, Cu leaching cannot be omitted during the process. Due to the low efficiency, further research should be focused on other environment-friendly methods of soil remediation.     

Cadmium accumulation in and tolerance of rice (Oryza sativa L.) varieties with different rates of radial oxygen loss

Cadmium (Cd) uptake and tolerance were investigated among 20 rice cultivars based on a field experiment (1.2 mg Cd kg⁻¹ in soil) and a soil pot trial (control, 100 mg Cd kg⁻¹), and rates of radial oxygen loss (ROL) were measured under a deoxygenated solution. Significant differences were found among the cultivars in: (1) brown rice Cd concentrations (0.11-0.29 mg kg⁻¹) in a field soil, (2) grain Cd tolerance (34-113%) and concentrations (2.1-6.5 mg kg⁻¹) in a pot trial, and (3) rates of ROL (15-31 mmol O₂ kg⁻¹ root d.w. h⁻¹). Target hazard quotients were calculated for the field experiment to assess potential Cd risk. Significant negative relationships were found between rates of ROL and concentrations of Cd in brown rice or straw under field and greenhouse conditions, indicating that rice cultivars with higher rates of ROL had higher capacities for limiting the transfer of Cd to rice and straw.     

Nitrous oxide emissions from mineral and organic soils of a Norway spruce stand in South–West Germany

Due to the high temporal and spatial variability of N₂O fluxes, estimates of N₂O emission from temperate forest ecosystems are still highly uncertain, particularly at larger scales. Although highest N₂O emissions with up to 7.0 kg N ha⁻¹ yr⁻¹ were mainly reported for soils affected by stagnant water, most of the reported gas flux measurements were performed at forest sites with well-aerated soils yielding mostly to low mean annual emission rates less than 1.0 kg N ha⁻¹ yr⁻¹. This study compares N₂O fluxes from upland (Cambisols) and temporally water-logged (Gleysols, Histosols) soils of the Central Black Forest (South-West Germany) over a period of 2 yr. Mean annual N₂O fluxes from investigated soils ranged between 0.2 and 3.9 kg N ha⁻¹ yr⁻¹. The fluxes showed a large variability between the different soil types. Emissions could be clearly ranked in the following order: Cambisols (0.26–0.75 kg N ha⁻¹ yr⁻¹)<Gleysols (1.37–2.68 kg N ha⁻¹ yr⁻¹)<Histosol (3.66–3.95 kg N ha⁻¹ yr⁻¹). Although the Cambisols cover two-thirds of the investigated area, only about half of the overall N₂O is emitted from this soil type. Therefore, regional or national N₂O fluxes from temperate forest soils are underestimated if soils characterised by intermediate aeration conditions are disregarded.     

Impact of earthworms on trace element solubility in contaminated mine soils amended with green waste compost

The common practice of remediating metal contaminated mine soils with compost can reduce metal mobility and promote revegetation, but the effect of introduced or colonising earthworms on metal solubility is largely unknown. We amended soils from an As/Cu (1150 mgAs kg⁻¹ and 362 mgCu kg⁻¹) and Pb/Zn mine (4550 mgPb kg⁻¹ and 908 mgZn kg⁻¹) with 0, 5, 10, 15 and 20% compost and then introduced Lumbricus terrestris. Porewater was sampled and soil extracted with water to determine trace element solubility, pH and soluble organic carbon. Compost reduced Cu, Pb and Zn, but increased As solubility. Earthworms decreased water soluble Cu and As but increased Pb and Zn in porewater. The effect of the earthworms decreased with increasing compost amendment. The impact of the compost and the earthworms on metal solubility is explained by their effect on pH and soluble organic carbon and the environmental chemistry of each element.     

Historical changes in atmospheric nitrogen deposition to Cape Cod,Massachusetts, USA

We reconstructed the historical trends in atmospheric deposition of nitrogen to Cape Cod, Massachusetts, from 1910 to 1995 by compiling data from literature sources, and adjusting the data for geographical and methodological differences. The reconstructed data suggest that NO₃-N wet deposition to this region increased from a low of 0.9 kg N ha⁻¹ yr⁻¹ in 1925 to a high of approximately 4 kg N ha⁻¹ yr⁻¹ around 1980. The trend in NO₃-N deposition has remained since the early 1980s at around 3.6 kg N ha⁻¹ yr⁻¹. In contrast, NH₄-N wet deposition decreased from more than 4 kg N ha⁻¹ yr⁻¹ in the mid 1920s to about 1.5 kg N ha⁻¹ yr⁻¹ from the late-1940s until today. Emissions of NO_x-N in the Cape Cod airshed increased at a rate of 2.1 kg N ha⁻¹ per decade since 1910, a rate that is an order of magnitude higher than NO₃-N deposition. Estimates of NH₃ emissions to the northeast United States and Canada have decreased slightly throughout the century, but the decrease in reconstructed N-NH₄⁺ deposition rates does not parallel emissions estimates. The trend in reconstructed total nitrogen deposition suggests an overall increase through the century at a rate of 0.26 kg N ha⁻¹ per decade. This overall increase in deposition may expose coastal forests to rates of nitrogen addition that, if exceeded, could induce nitrogen saturation and increase nitrogen loads to adjoining estuaries.     

Sorption of perfluorooctane sulfonate to carbon nanotubes in aquatic sediments

To date, sorption of organic compounds to nanomaterials has mainly been studied for the nanomaterial in its pristine state. However, sorption may be different when nanomaterials are buried in sediments. Here, we studied sorption of Perfluorooctane sulfonate (PFOS) to sediment and to sediment with 4% multiwalled carbon nanotubes (MWCNTs), as a function of factors affecting PFOS sorption; aqueous concentration, pH and Ca²⁺ concentration. Sorption to MWCNT in the sediment–MWCNT mixtures was assessed by subtracting the contribution of PFOS sorption to sediment-only from PFOS sorption to the total sediment–MWCNT mixture. PFOS Log K_D values ranged 0.52–1.62 L kg^?1 for sediment and 1.91–2.90 L kg^?1 for MWCNT present in the sediment. The latter values are relatively low, which is attributed to fouling of MWCNT by sediment organic matter. PFOS sorption was near-linear for sediment (Freundlich exponent of 0.92 ± 0.063) but non-linear for MWCNT (Freundlich exponent of 0.66 ± 0.03). Consequently, the impact of MWCNT on sorption in the mixture was larger at low PFOS aqueous concentration. Effects of pH and Ca²⁺ on PFOS sorption to MWCNT were statistically significant. We conclude that MWCNT fouling and PFOS concentration dependency are important factors affecting PFOS–MWCNT interactions in sediments.     

Sorption of polar and nonpolar organic contaminants by oil-contaminated soil

Sorption of nonpolar (phenanthrene and butylate) and polar (atrazine and diuron) organic chemicals to oil-contaminated soil was examined to investigate oil effects on sorption of organic chemicals and to derive oil–water distribution coefficients (K_oil). The resulting oil-contaminated soil–water distribution coefficients (K_d) for phenanthrene demonstrated sorption-enhancing effects at both lower and higher oil concentrations (C_oil) but sorption-reducing (competitive) effects at intermediate C_oil (approximately 1 g kg⁻¹). Rationalization of the different dominant effects was attempted in terms of the relative aliphatic carbon content which determines the accessibility of the aromatic cores to phenanthrene. Little or no competitive effect occurred for butylate because its sorption was dominated by partitioning. For atrazine and diuron, the changes in K_d at C_oil above approximately 1 g kg⁻¹ were negligible, indicating that the presently investigated oil has little or no effect on the two tested compounds even though the polarity of the oil is much less than soil organic matter (SOM). Therefore, specific interactions with the active groups (aromatic and polar domains) are dominantly responsible for the sorption of polar sorbates, and thus their sorption is controlled by available sorption sites. This study showed that the oil has the potential to be a dominant sorptive phase for nonpolar pollutants when compared to SOM, but hardly so for polar compounds. The results may aid in a better understanding of the role of the aliphatic and aromatic domains in sorption of nonpolar and polar organic pollutants.