Use of quadrupole GC-MS and ion trap GC-MS-MS for determining 3-hydroxy fatty acids in settled house dust: relation to endotoxin activity

Gas chromatography-mass spectrometry (GC-MS) using a quadrupole instrument and GC-tandem MS (GC-MS-MS) using an ion trap instrument were applied to determine 3-hydroxy fatty acids (3-OH FAs) with 10-18 carbon chain lengths, specific components of the endotoxin (lipopolysaccharide, LPS) of Gram-negative bacteria, in 30 house dust samples. The two methods provided similar detection sensitivity for methyl ester/trimethylsilyl derivatives of the 3-OH FAs and allowed these acids to be distinguished from co-eluting 2-OH FA derivatives. The correlation coefficients between endotoxin activity (Limulus test) and the combined amounts of 3-OH C10, 3-OH C12, and 3-OH C14 were 0.60 and 0.61 when using GC-MS and GC-MS-MS, respectively. The superior selectivity of GC-MS-MS was illustrated in analyses of sub-milligram amounts of dust, where the chromatograms achieved by GC-MS were difficult to interpret due to a high background and several closely eluting compounds. GC-MS-MS is therefore preferable to GC-MS for determining 3-OH FAs in minute (sub-milligram) amounts of dust.     

“MMA”技术路线在太湖蓝藻水华监测中的应用

通过对3S技术整合,提出"MMA"技术路线应用于蓝藻水华监测,包括监测、测绘、分析等关键步骤。对太湖蓝藻水华研究结果表明,总体规律一致,但又有所差异。一方面,太湖蓝藻密度(CBD)、叶绿素a(Chl-a)及水华频率分布图结果均呈现"西高东低"的空间分布规律;另一方面,太湖湖心区CBD和Chl-a浓度亦较高,而遥感监测后的水华频率图显示为无水华或频率小于1%。故应参照"MMA"技术路线,综合应用3S技术,并核验比对,弥补单项技术存在的不足,全面真实反映藻类水华情况。"MMA"技术路线既适用于水华监测,亦可推广至其他环境监测工作。     

利用MALDI-TOF MS技术简便、快速检测水华蓝藻的方法研究

以水华蓝藻为研究对象,用基质辅助激光解吸电离飞行时间质谱(MALDI-TOF MS)技术对其进行测定分析并获得了蛋白质指纹图谱。对铜绿微囊藻标准株(NIES-843)样品通过3种前处理方法得到的质谱图进行对比,确定了质谱分析的样品前处理方法,建立了利用MALDI-TOF MS技术简便、快速检测水华蓝藻的方法。对在水华中出现的4种不同蓝藻进行MALDI-TOF MS分析,结果表明各种蓝藻具有其特征性波谱,可据此对水华蓝藻进行区分和鉴定。该方法快速、简便、精确、可程序化,具有广泛的应用前景。     

X射线荧光光谱法测定土壤样品中铅的不确定度评定

用实例对X射线荧光光谱法测定土壤样品中铅的不确定度进行了评定.测量结果的不确定度由仪器综合稳定性、制样、标准物质、回归工作曲线、重复测量等所引入的不确定度分量组成.在对各个不确定度分量进行量化的基础上,通过合成得到测量结果的标准不确定度,再乘以95%置信概率下的扩展因子2,得到测量结果的扩展不确定度.     

Equivalency of a personal dust monitor to the current United States coal mine respirable dust sampler

The United States National Institute for Occupational Safety and Health, through an informal partnership with industry, labor, and the United States Mine Safety and Health Administration, has developed and tested a new instrument known as the Personal Dust Monitor (PDM). The new dust monitor is an integral part of the cap lamp that coal miners normally carry to work and provides continuous information about the concentration of respirable coal mine dust within the breathing zone of that individual. Previous laboratory testing demonstrated that there is a 95% confidence that greater than 95% of individual PDM measurements fall within +/-25% of reference measurements. The work presented in this paper focuses on the relationship between the PDM and respirable dust concentrations currently measured by a coal mine dust personal sampler unit utilizing a 10 mm Dorr-Oliver nylon cyclone. The United Kingdom Mining Research Establishment instrument, used as the basis for coal mine respirable dust standards, had been designed specifically to match the United Kingdom British Medical Research Council (BMRC) criterion. The personal sampler is used with a 1.38 multiplier to convert readings to the BMRC criterion. A stratified random sampling design incorporating a proportionate allocation strategy was used to select a sample of mechanized mining units representative of all US underground coal mines. A sample of 180 mechanized mining units was chosen, representing approximately 20% of the mechanized mining units in production at the time the sample was selected. A total of 129 valid PDM/personal sampler dust sample sets were obtained. A weighted linear regression analysis of this data base shows that, in comparison with the personal sampler, the PDM requires a mass equivalency conversion multiplier of 1.05 [95% C.I.=(1.03, 1.08)] when the small intercept term is removed from the analysis. Removal of the intercept term results in a personal sampler-equivalent concentration increase of 2.9% at a PDM measurement of 2.0 mg m(-3).     

A method for measuring the potential dermal exposure to methyl methacrylate during two different dental technical work tasks

Dental technicians are exposed on a daily basis to undiluted methyl methacrylate (MMA) when performing various routine tasks. Although the clinical effects of this chemical have been known for decades, no previous studies have been performed to estimate the potential dermal exposure to it. In this study we describe a patch-sampling technique to intercept the MMA that would otherwise have contaminated the skin on different parts of the hand and lower arm. Two different work tasks, making an orthodontic splint and denture preparation, were both performed under simulated workplace conditions twice by two recent graduated dental technicians. Air measurements were collected simultaneously. The results indicate that the exposure patterns associated with producing an orthodontic splint and denture preparation differed. We found work task-dependent differences in the amounts of MMA collected at the different parts of each hand, and differences between the right and left hands. There was also an interaction between hand and work task, especially for the right hand. The air measurements were positively correlated with the dermal exposure. This study highlights the importance of using a measurement strategy that takes the variability within the hand/arm body parts into account when measuring potential exposure during these kinds of work tasks. In order to establish future dermal exposure limits, more workplace and experimental studies are required.     

光散射法扬尘在线监测质量管理研究与应用

主要阐述了光散射法扬尘在线监测应用于建筑工地、干散货码头堆场、混凝土搅拌站的质量管理和质量评估。为了提高光散射法扬尘在线监测的数据质量,上海市采取扬尘在线监测设备现场质量抽测的模式,通过对在用仪器的监测点位、除湿方式、校准方式、质量浓度转换系数、与标准重量法监测结果的相对误差和相关系数、仪器运行维护水平等影响监测质量和数据有效性的关键指标的检查,开展扬尘监测在用仪器质量评估和仪器商合格评定,稳步提高在用仪器质量,为在线监测质量管理和质量评估提供可借鉴的技术方案和实践经验。     

国家环境标准样品在环境有机污染物分析中的应用

简介了在分析环境中的有机污染物时,标准样品作为替代物、基体加标物在样品前处理中的应用,及其作为仪器性能检验物、校正物、内标物在样品分析过程中的应用。     

影响地表水高锰酸盐指数自动监测数据准确性的因素

地表水高锰酸盐指数自动监测仪器在实际应用中存在质控样测试和实际水样比对测试合格率相对偏低的问题。通过对高锰酸盐指数氧化还原机理的分析,结合目前国控水站对质控样品的测试数据,探讨了如何使用高锰酸盐指数自动监测仪分析测试得到准确可靠的水质监测数据。认为应尽量保持自动分析仪器的反应条件、稀释条件与标准方法一致,即取样量与试剂用量比与标准方法一致,并根据样品浓度变化实现量程自动切换,分量程进行仪器校准和测量,才能够提高自动分析仪器测量的准确性。     

水中氯代酸性除草剂衍生气相色谱法主要要素探讨

建立了衍生气相色谱-负化学源质谱检测水中氯代酸性除草剂的方法,从四个方面对氯代酸性除草剂衍生气相色谱法中主要要素分析:针对不同需求选择确定萃取模式、萃取溶剂、酸度、浓缩方式等;对不同衍生方式进行比较,分析了辅助条件的必要性;针对衍生产物的不同选择离子源;标准物质的合理使用。     

Evaluation of interference to conventional and real-time PCR for detection and quantification of fungi in dust

Advances in polymerase chain reaction (PCR) have permitted accurate, rapid and quantitative identification of microorganisms in pure cultures regardless of viability or culturability. In this study, a simple sample processing method was investigated for rapid identification and quantification of fungal spores from dust samples using both conventional and real-time PCR. The proposed method was evaluated for susceptibility to interference from environmental dust samples. Stachybotrys chartarum and Aspergillus fumigatus were used as test organisms. The sensitivity of detection in pure culture was 0.1 spore DNA equivalents per PCR reaction corresponding to 20 spores ml(-1) in the sample. However, 1 spore DNA equivalent per PCR reaction corresponding to 200 spores ml(-1) in the sample was the lowest amount of spores tested without interference in dust samples spiked with spores of either fungal species. The extent of inhibition was calculated using conventional and real-time PCR reactions containing fungal spores, specific primers, specific probes (for real-time PCR) and various amounts of dust. The results indicate that the extent of inhibition by dust on PCR varies with the type and amount of dust, and number of spores. No interference in the analysis of spiked samples was detected from 0.2 mg ml(-1) of four real-life dust samples at p-value >0.05 using 2 x 10(4) spores for conventional PCR and 2 x 10(5) spores for real-time PCR. However, samples containing >0.2 mg ml(-1) real-life dust compromised the PCR assay. These results suggest the potential usefulness of a simple sample processing method in conjunction with PCR for monitoring the fungal content of aerosols collected from indoor environments.     

统计学在垃圾焚烧飞灰浸提液重金属检测准确性研究中的应用

为提高复杂基体重金属检测准确性,在使用电感耦合等离子体发射光谱法检测生活垃圾焚烧飞灰浸提液时,进行标准曲线法、标准加入法和内标法3种定量校准方法比对。3种方法报出结果经过加标回收率换算后的样品原值具有明显一致性,使用统计学方差齐性和单因素方差分析验证了该一致性成立,表明内标法的精密度和准确度与标准曲线法、标准加入法无显著性差别。以3种方法样品原值的算数平均值作为样品最佳估计值评价各方法实际报出结果准确性,标准加入法准确性最好;稀释后的样品内标法加标回收率明显优于标准规定,受稀释倍数影响不大,工作效率高,满足HJ 781—2016质控要求,建议可作为该标准的补充;建议批量样品检测时优先采用内标法。3种方法样品原值一致性的验证,有助于执法、科研中对于复杂基体重金属物质含量的准确判断。     

巯基棉富集-毛细柱气相色谱法测定环境水中的甲基汞

用巯基棉富集-毛细柱气相色谱法对水中甲基汞进行测定,具有选择性强,回收率高,灵敏度高等优点。实际样品加标回收率达到85%以上,最低可检出0.6ng/L的浓度。研究结果表明,与填充柱法相比,毛细柱法对目标物的分离效果好,且不会发生柱中毒反应,避免了用氯化汞对色谱柱进行处理的步骤。论证了用甲苯代替苯做为萃取剂的可行性,证明用甲苯代替苯对测试结果没有显著影响,使用甲苯可以避免实验人员暴露于毒性较大的苯中的风险。     

PT-GC-CAFS联用技术测定污水处理厂外排水中烷基汞残留量

建立了吹扫捕集-气相色谱-冷原子荧光(PT-GC-CAFS)联用技术、多功能自动进样器进样测定污水处理厂外排水中烷基汞残留量的方法。用烷基化试剂直接衍生,吹扫捕集吸附/富集,以PEG20M填充柱为分离柱,用冷原子荧光作为检测器进行测定,整体分析工作在10 min内完成。在所选实验条件下,方法对所测甲基汞、乙基汞的线性相关系数分别为0.999 9、1.000,最低检出限分别为0.002、0.003 ng/L,相对标准偏差为1.4%~10.2%,2.3%~9.7%;在不同质量浓度水平上进行加标回收率实验,甲基汞的回收率为93.7%~101.7%,乙基汞为94.1%~103.6%。该方法用于污水处理厂外排水中烷基汞残留量的分析测定,结果令人满意。     

A comparison of methods and materials for the analysis of leaded wipes

The purposes of this study are: (1) to determine whether proficiency analytical test (PAT) materials from the American Industrial Hygiene Association can be used to provide quality data for portable X-ray fluorescence analysis (XRF) of lead in dust wipe surface samples; (2) to provide data to determine whether the on-site analysis of field dust wipe samples by XRF and the laboratory method of inductively coupled plasma emission analysis (ICP) are comparable; and (3) to determine if differences exist between different wipe materials. Several wipes meet the ASTM E1792 performance requirements of lead background level less than 5 microg per wipe, be only one layer thick, yield recovery rates of 80- 120% from spiked samples, remain damp throughout the sampling procedure, and do not contain aloe. The wipes used in this study were Pace Wipes, which are used for the PAT materials, and, for the field samples, Palintest Wipes, which were supplied by the instrument manufacturer, and Ghost Wipes, which are popular because they digest in hot, concentrated acid, so that chemical analysis is simplified. Twenty PAT wipe samples were obtained from four different proficiency test rounds. Surface wipe samples were taken at three different locations representing different industry types. All samples were analyzed using a portable XRF spectrometer and by ICP. Strong linear relationships were found for the analysis of wipe samples by ICP and by portable XRF. For the PAT samples, the results from the ICP and XRF analysis were not statistically equivalent, which indicates a bias in the ICP analysis. The bias was not excessive, since all ICP analyses fell within the acceptable range for the proficiency samples. The good correlation between the proficiency sample reference values and the XRF determinations is not surprising considering similar proficiency samples were used to calibrate the instrument response. Users of this portable XRF analyzer could enroll in the proficiency test program as part of their quality assurance program. For field samples, the relationship was strongest for Palintest wipes, and the values found for all three industries could be combined. However, the results from the ICP and XRF analysis were not statistically equivalent using the correction factor in the calculation algorithm as supplied with the instrument, and a new coefficient was derived. The mean relative error for the XRF analysis versus the ICP analysis was greater than 25%, such that the method falls within the realm of screening procedures. For Ghost Wipe samples, the precision was different for different industries, and the results could not be pooled. Differences between the two wipe materials may be related to the number of folds required for analysis.     

气相色谱法检测废气中甲烷、非甲烷总烃的问题研究

气相色谱法检测废气中甲烷、非甲烷总烃的方法存在诸多问题。针对标准参考气体的选择、采样方式、样品保存、配气方式、仪器配置等方面做了重点研究。结果表明,使用甲烷作为标准参考气体最佳,根据污染源的实际状况,可选择动力采样或玻璃注射器手动采样。样品气保存在惰性气袋中比玻璃注射器更好,实验分析更推荐双柱配置的气相色谱,手工配制标准气系列、使用填充柱也可很好的满足检测的质量要求。     

电感耦合等离子体-质谱法内标元素选择的研究

电感耦合等离子体-质谱(ICP-MS)测定土壤标样中不同质量段的Cr、Cd、Pb元素,借以研究内标元素选择对测定值的影响。结果表明:选择内标元素,首要考虑因素是样品中不含该元素,而非质量数或第一电离能与待测元素接近;选择样品中含有成分作为内标元素时,对低浓度含量的元素影响更大;单一内标元素即可校正基体效应,实现对低、中、高质量段的多元素同时测定。对地质标样和未知样品,分别推荐了内标元素和选择内标元素的方法。     

Sampling and analytical methodology development for the determination of primary and secondary low molecular weight amines in ambient air

In this project, a sampling device and an analytical method have been developed to simultaneously analyse the most frequently found low molecular weight amines, including aliphatic, aromatic and alcohol amines. These amines are diethanolamine, ethanolamine, methylamine, isopropylamine, morpholine, dimethylamine, and aniline. A sampling device was developed using a 37 mm cassette with glass fibre filters impregnated with sulfuric acid. Immediately after sampling, the filter was transferred to vials containing a solution of dansyl chloride. Dansyl chloride was used for derivatisation because it forms aromatic sulfonamides that are fluorescent and easy to protonate for MS detection. The effect of using an internal standard made with the dansylated derivative of 1-(2-methoxyphenyl)piperazine (MOPIP) on the uncertainty and efficiency of the method was also evaluated. This internal standard was spiked directly onto filters. The coupling of HPLC/ESI-MS was used for the simultaneous analysis of all the derivatives. This method showed detection limits of about 0.03 microg mL(-1) to 0.3 microg mL(-1) of amine with an average expanded uncertainty of 3% to 6% depending on the amine. The methodology recoveries are close to 100% for all the amines, and the overall estimated expanded uncertainties vary between 10% and 13% depending on the amine. This new strategy will be useful in evaluating workplace air since a unique sampling system will be used, independent of the amine to be quantified.     

全自动甲基汞分析仪测定水和废水中甲基汞

建立了全自动甲基汞分析仪测定水和废水中甲基汞的方法,对较清洁的地表水和一般废水样品可直接衍生化测定,对基体复杂水样则需蒸馏后再衍生化测定。该法在水样中甲基汞含量为0~1 000 pg范围内线性良好,相关系数r为0.999 7,检出限为0.002 ng/L,标准参考物质测定结果均在参考值范围内,相对标准偏差为1.1%,加标回收率为83.2%~96.6%。该法适用于水及废水中甲基汞的检测。     

Addressing the challenges of tetracycline analysis in soil: extraction, clean-up, and matrix effects in LC-MS

An optimized extraction and clean-up method for the analysis of chlortetracycline, doxycycline, oxytetracycline, and tetracycline antibiotics in soil is presented in this work. Soil extraction using different solvents was performed, but the use of a 50 : 50 (v/v) methanol : acetate buffer (pH 8) solvent mixture in a pressurized liquid extraction (PLE) system proved to give the best extraction efficiency and reproducibility. The effect of soil composition on the PLE extraction efficiency was also examined, and results indicated that recovery data for one soil is not necessarily consistent with other soil types containing different compositions of clay and organic matter content. The percent recoveries of the optimized PLE method varied between the soils and ranged from 22-99%, depending on soil type, and more specifically clay content. In addition, the extent of ionization suppression caused by co-extracted humic acids was examined in an ion trap mass spectrometer (MS), and a single quadrupole MS. It was found that under positive electrospray ionization, the single quadrupole MS was less susceptible to ionization suppression than the ion trap MS. Therefore, various sample clean-up procedures were evaluated to selectively reduce the amount of co-extracted humic acids in the soil extracts. The most effective clean-up was obtained from the use of StrataX sorbent in combination with a strong anion exchange cartridge.