Degradation and metabolite production of tylosin in anaerobic and aerobic swine-manure lagoons.

Watershed contamination from antibiotics is becoming a critical issue because of increased numbers of confined animal-feeding operations and the use of antibiotics in animal production. To understand the fate of tylosin in manure before it is land-applied, degradation in manure lagoon slurries at 22 degrees C was studied. Tylosin disappearance followed a biphasic pattern, where rapid initial loss was followed by a slow removal phase. The 90% disappearance times for tylosin, relomycin (tylosin D), and desmycosin (tylosin B) in anaerobically incubated slurries were 30 to 130 hours. Aerating the slurries reduced the 90% disappearance times to between 12 and 26 hours. Biodegradation and abiotic degradation occur, but strong sorption to slurry solids was probably the primary mechanism of tylosin disappearance. Dihydrodesmycosin and an unknown degradate with molecular mass of m/z 934.5 were detected. Residual tylosin remained in slurry after eight months of incubation, indicating that degradation in lagoons is incomplete and that residues will enter agricultural fields.     

Laboratory leaching studies of oryzalin and diuron through three undisturbed vineyard soil columns

The leaching of diuron and oryzalin through undisturbed soil columns was studied in the laboratory using three vineyard soils from Vosne-Romanée (Burgundy): a rendosol, a calcosol and a vegetated calcosol. After 845 mm of simulated rainfall in 15 days, soil leachates contained higher amounts of diuron (3.2%, 11.8% and 18.8% of applied diuron, respectively) than oryzalin (0.2%, 4.9%, 3.7%, respectively). A greater proportion of soil extractable residues was obtained for diuron (42.5%, 26.8% and 32.2%, respectively) than for oryzalin (14.7%, 12% and 15.5%, respectively). The greater mobility of diuron might be related to its higher water solubility (36.4 mgl(-1) compared with 2.6 mgl(-1) for oryzalin) and smaller adsorption coefficient (400 lkg(-1), compared with 700-1100 lkg(-1) for oryzalin). The mobility of the two herbicides was greater in the two calcosols than in the rendosol, not only due to different organic carbon contents but also different soil textures and structures.     

Tylosin sorption to silty clay loam soils, swine manure, and sand

The objectives of this study were to assess sorption and desorption of tylosin, a macrolide antimicrobial chemical used in swine, cattle, and poultry production, in three silty clay loam soils of South Dakota and compare soil sorption to sand and manure sorption. The silty clay loam soils, from a toposequence in eastern South Dakota, standardized sand samples, and swine manure were used in 24-h batch sorption studies with tylosin concentrations ranging from 25 to 232 micro mole/L. Desorption from soil was conducted over a four-day period. Partition coefficients, based on the Freundlich isotherm (K(f)) or K(d) values, were calculated. K(f) values for the silty clay loams were similar, not influenced by landscape position, and averaged 1,350 with isotherm slopes ranging from 0.85 to 0.93. K(f) values for sand were dependent on solution/sand ratios and pH, ranging from 1.4 to 25.1. K(d) values of manure were dependent on the solution type and ranged from 840 L/kg with urine to about 175 L/kg when sorbed from water. Desorption of tylosin from each soil over the four-day period was < 0.2% of the amount added. The soils' high K(f) values and low desorption amounts suggest that once tylosin is in these soils, leaching to lower depths may not occur. However, this does not preclude runoff with soil eroded particles. If tylosin reaches a sand aquifer, through bypass flow or other mechanism(s), movement in the aquifer most likely would occur.     

Determination of the distribution coefficient (log Kd) of oxytetracycline,tylosin A,olaquindox and metronidazole in manure

Olaquindox (log Kow = -2.3) and metronidazole (log Kow = -0.1) both have low tendencies to sorp to particles in manure. This corresponds with the negative log Kow values of these antibiotics. Tylosin (log Kow = 1.63) and oxytetracycline (log Kow = -1.12) sorp relatively strongly to the manure particles and have log Kd values between 1.5 and 2.0. The tendency to bind to manure was ranked after increasing binding as follows: metronidazole < olaquindox < tylosin A and oxytetracycline. This order of ranking is consistent with results of sorption in soil. Our experiments illustrate that for some antibacterial agents estimation of the partitioning coefficients, Kd, cannot be made from Kow and f(oc) alone. Sorption of oxytetracycline to manure is much higher than expected from the negative log Kow value of the compound. It is believed that sorption of oxytetracycline to manure is influenced by ionic binding to divalent metal ions as such Mg2+ and Ca2+ as well as other charged compounds in the matrix. Binding of oxytetracycline to soil is stronger than the binding to manure. This is most likely due to the strong mineral related metal complexes formed between soil, metal ion and oxytetracycline. These complexes are not known to exist in manure. The relatively strong sorption of tylosin A to manure corresponds with data found for soil sorption of tylosin. Tylosin has a log Kow value of 2.5, thus it is not surprising that this drug binds strongly to manure.     

Experimental evidence for in situ natural attenuation of 2,4- and 2,6-dinitrotoluene in marine sediment

Dinitrotoluenes (DNTs) are widely used in the manufacturing of explosives and propellants hence causing contamination of several terrestrial and aquatic environments. The present study describes biotransformation of 2,4-DNT and 2,6-DNT in marine sediment sampled from a shipwreck site near Halifax Harbour. Incubation of either 2,4-DNT or 2,6-DNT in anaerobic sediment slurries (10% w/v) at 10 degrees C led to the reduction of both DNTs to their corresponding diaminotoluene (2,4-DAT and 2,6-DAT) via the intermediary formation of their monoamine derivatives (ANTs). The production of diaminotoluene was enhanced in the presence of lactate for both DNT isomers. Using [(14)C]-2,4-DNT less than 1% mineralization was observed as determined by liberated (14)CO(2). Sorption of DNTs, ANTs, and DATs was thus investigated to learn of their fate in marine sediments. Under anaerobic conditions, sorption followed the order: DNTs (K(d)=8.3-11.7lkg(-1))>ANTs (K(d)=4.5-7.0lkg(-1))>DATs (K(d)=3.8-4.5lkg(-1)). Incubation of 2,4-DAT in aerobic sediment led to rapid disappearance from the aqueous phase. LC/MS analysis of the aqueous phase and the acetone sediment extract showed the formation of azo- and hydrazo-dimers and trimers, as well as unidentified polymers. Experiments with radiolabelled 2,4-DAT showed a mass balance distributed as follows: 22% in the aqueous phase, 24% in acetone extracts, and 50% irreversibly bound to sediment. We concluded that DNT in anoxic marine sediment can undergo in situ natural attenuation by reduction to DAT followed by oxidative coupling to hydrazo-oligomers or irreversible binding to sediment.     

Nutrient losses by surface run-off following the application of organic manures to arable land. 1. Nitrogen

Research was conducted on nitrogen (N) surface run-off losses following organic manure applications to land, utilising a purpose-built facility on a sloping site in Herefordshire under arable tillage. Different rates and timing of cattle slurry, farmyard manure and inorganic N and phosphorus (P) fertiliser were compared, over a 4-year period (1993-97). P losses from the same studies are reported in a separate paper. The application of cattle slurries to the silty clay loam soil increased the loss of solids and NH4(+)-N in surface water flow compared to control plots receiving inorganic fertiliser only, or no treatment, but had little effect on NO3(-)-N losses by this route. Results were consistent with other observations that rainfall events immediately after manure applications are particularly likely to be associated with nutrient run-off losses. Losses via subsurface flow (30 cm interflow) were consistently much lower than via surface water movement and were generally unaffected by treatment. Increasing slurry application rate and, in particular, slurry solids loading, increased solids and NH4(-)-N losses via surface run-off. The threshold, above which the risk of losses via surface run-off appeared to be greatly increased, was ca. 2.5-3.0 t/ha slurry solids, which approximates to the 50 m3/ha limit suggested for slurry within UK 'good agricultural practice'. Sealing of the soil surface by slurry solids appears to be a possible mechanism by which polluting surface run-off may occur following slurry application on susceptible soils. Total losses of NH4(+)-N and NO3(-)-N during the 4-year monitoring period were insignificant in agronomic terms, but average soluble N concentrations (NH4(+)-N + NO3(-)-N) in run-off, ranging from ca. 2.0 mg/l, up to 14.0 mg/l for the higher rate slurry treatments. Peak concentrations of NH4(+)-N > 30 mg/l, are such as to be of concern in sensitive catchments, in terms of the potential for contribution to accelerated eutrophication and adverse effects on freshwater biota.     

The dissipation and transport of veterinary antibiotics in a sandy loam soil

The environmental fate of the antibiotics sulfachloropyridazine and oxytetracycline was investigated in a sandy loam soil. Liquid pig manure was fortified with the compounds and then applied to soil plots to investigate leaching, dissipation and surface run-off under field conditions. Additionally, as the macrolide antibiotic tylosin had been administered to the pigs from which the slurry had been sourced, this was also analysed for in the samples collected. Sulfachloropyridazine dissipated rapidly with DT(50) and DT(90) values of 3.5 and 18.9 days but oxytetracycline was more persistent with DT(50) and DT(90) values of 21.7 and 98.3 days. Both sulfachloropyridazine and oxytetracyline were detected in surface run-off samples at maximum concentrations of 25.9 and 0.9microg/l respectively but only sulfachloropyridazine was detected in soil water samples at a maximum concentration of 0.78microg/l at 40cm depth 20 days after treatment. Tylosin was not detected in any soil or water samples. The results indicated that tylosin, when applied in slurry, posed very little risk of accumulating in soil or contaminating ground or surface water. However, tylosin may pose a risk if used to treat animals on pasture and risks arising from transformation products of tylosin, formed during slurry storage, cannot be ruled out. Oxytetracycline posed a very low risk of ground or surface water contamination but had the potential to persist in soils and sulfachloropyridazine posed a moderate risk of contaminating ground or surface water but had low potential to accumulate in soils. These findings were consistent with the sorption and persistence characteristics of the compounds and support a number of broad-scale monitoring studies that have measured these antibiotic classes in the environment.     

Aerobic granulation for 2,4-dichlorophenol biodegradation in a sequencing batch reactor

Development of aerobic granules for the biological degradation of 2,4-dichlorophenol (2,4-DCP) in a sequencing batch reactor was reported. A key strategy was involving the addition of glucose as a co-substrate and step increase in influent 2,4-DCP concentration. After operation of 39d, stable granules with a diameter range of 1-2mm and a clearly defined shape and appearance were obtained. After granulation, the effluent 2,4-DCP and chemical oxygen demand concentrations were 4.8mgl(-1) and 41mgl(-1), with high removal efficiencies of 94% and 95%, respectively. Specific 2,4-DCP biodegradation rates in the granules followed the Haldane model for substrate inhibition, and peaked at 39.6mg2,4-DCPg(-1)VSS(-1)h(-1) at a 2,4-DCP concentration of 105mgl(-1). Efficient degradation of 2,4-DCP by the aerobic granules suggests their potential application in the treatment of industrial wastewater containing chlorophenols and other inhibitory chemicals.     

Nutrient losses by surface run-off following the application of organic manures to arable land. 2. Phosphorus

Phosphorus (P) surface run-off losses were studied following organic manure applications to land, utilising a purpose-built facility on a sloping site in Herefordshire under arable tillage. Different rates and timing of cattle slurry, farm yard manure (FYM) and inorganic nitrogen (N) and P fertiliser were compared, over a 4-year period (1993-97). N losses from the same studies are reported in a separate paper. The application of cattle FYM and, especially slurry, to the silty clay loam soil increased both particulate and soluble P loss in surface water flow. Losses via subsurface flow (30 cm interflow) were consistently much lower than via surface water movement and were generally unaffected by treatment. Increased application of slurry solids increased all forms of P loss via surface run-off; the results suggested that a threshold for greatly increased risk of P losses via this route, as for N, occurred at ca. 2.5-3.0 t/ha solids loading. This approximates to the 50 m3/ha application rate limit suggested for slurry within UK 'good agricultural practice'. The studies also provided circumstantial evidence of the sealing of the soil surface by slurry solids as the major mechanism by which polluting surface run-off may occur following slurry application on susceptible soils. Losses of total and soluble P, recorded for each of the 4 years of experiments, reached a maximum of only up to 2 kg/ha total P (TP), even after slurry applications initiating run-off. Whilst these losses are insignificant in agronomic terms, peak concentrations of P (up to 30,000 micrograms/l TP) in surface water during a run-off event, could be of considerable concern in sensitive catchments. Losses of slurry P via surface run-off could make a significant contribution to accelerated eutrophication on entry to enclosed waters, particularly when combined with high concentrations of NO3(-)-N. Restricting slurry application rates to those consistent with good agronomic practice, and within the limits specified in existing guidelines on good agricultural practice, offers the simplest and most effective control measure against this potentially important source of diffuse pollution.     

Seasonal and spatial variations of ammonia emissions from an open-lot dairy operation

There is a need for a robust and accurate technique to measure ammonia (NH3) emissions from animal feeding operations (AFOs) to obtain emission inventories and to develop abatement strategies. Two consecutive seasonal studies were conducted to measure NH3 emissions from an open-lot dairy in central Texas in July and December of 2005. Data including NH3 concentrations were collected and NH3 emission fluxes (EFls), emission rates (ERs), and emission factors (EFs) were calculated for the open-lot dairy. A protocol using flux chambers (FCs) was used to determine these NH3 emissions from the open-lot dairy. NH3 concentration measurements were made using chemiluminescence-based analyzers. The ground-level area sources (GLAS) including open lots (cows on earthen corrals), separated solids, primary and secondary lagoons, and milking parlors were sampled to estimate NH3 emissions. The seasonal NH3 EFs were 11.6 +/- 7.1 kg-NH3 yr(-1)head(-1) for the summer and 6.2 +/- 3.7 kg-NH3 yr(-1)head(-1) for the winter season. The estimated annual NH3 EF was 9.4 +/- 5.7 kg-NH3 yr(-1)head(-1) for this open-lot dairy. The estimated NH3 EF for winter was nearly 47% lower than summer EF. Primary and secondary lagoons (approximately 37) and open-lot corrals (approximately 63%) in summer, and open-lot corrals (approximately 95%) in winter were the highest contributors to NH3 emissions for the open-lot dairy. These EF estimates using the FC protocol and real-time analyzer were lower than many previously reported EFs estimated based on nitrogen mass balance and nitrogen content in manure. The difference between the overall emissions from each season was due to ambient temperature variations and loading rates of manure on GLAS. There was spatial variation of NH3 emission from the open-lot earthen corrals due to variable animal density within feeding and shaded and dry divisions of the open lot. This spatial variability was attributed to dispirit manure loading within these areas.     

Assessment of the importance of sorption for steroid estrogens removal during activated sludge treatment

Distribution coefficients (K(d)) between water and activated sludge particles (f(oc)=27.7+/-0.1%) were measured for the steroid estrogens (SE), estrone (E1), 17beta-estradiol (E2) and 17alpha-ethinylestradiol (EE2) in batch experiments. Experimental concentration levels ranged from environmentally realistic low ng/l to the high microg/l. In this range K(d)s were independent of their water concentration. The experimentally obtained K(d)s (with 95% confidence intervals) were 402+/-126 l/kg, 476+/-192 l/kg and 584+/-136 l/kg for E1, E2 and EE2, respectively. K(d)s were used to estimate the fraction of the total SE concentration that is expected to be sorbed in the activated sludge treatment tanks of a typical STP assuming equilibrium conditions. Assuming a suspended solids concentration of 4 g/l dissolved solids (ds), it was estimated that 61+/-9%, 66+/-13% and 70+/-6% of the total concentration of E1, E2 and EE2, respectively, would be sorbed during activated sludge treatment. The fraction of the SEs that was expected to be sorbed to suspended sludge particles in the effluents from a typical Danish STP was estimated to be only 0.20+/-0.06%, 0.24+/-0.10% and 0.29+/-0.07% of the total concentration of E1, E2 and EE2, respectively, at a suspended solids concentration of 5 mg/lds. For a typical STP the removal of steroid estrogens with excess sludge was estimated to be only 1.5-1.8% of the total loading if equilibrium conditions exists. Sorption is therefore not important for the fate of SEs in STPs compared to biodegradation.     

Toxicity of hexahydro-1,3,5-trinitro-1,3,5-triazine to larval zebrafish (Danio rerio)

Hexahydro-1,3,5-trinitro-1,3,5-triazine, a cyclonitramine commonly known as RDX, is used in the production of military munitions. Contamination of soil, sediment, and ground and surface waters with RDX has been reported in different places around the world. Acute and subacute toxicities of RDX have been relatively well documented in terrestrial vertebrates, but among aquatic vertebrates the information available is limited. The objective of this study was to characterize the acute toxicity of RDX to larval zebrafish. Mortality (LC50) and incidence of vertebral column deformities (EC50) were two of the end points measured in this study. The 96-h LC50 was estimated at 22.98 and 25.64 mgl(-1) in two different tests. The estimated no-observed-effective-concentration (NOEC) values of RDX on lethality were 13.27+/-0.05 and 15.32+/-0.30 mgl(-1); and the lowest-observed-effective-concentration (LOEC) values were 16.52+/-0.05 and 19.09+/-0.23 mgl(-1) in these two tests, respectively. The 96-h EC50 for vertebral deformities on survivors from one of the acute lethality tests was estimated at 20.84 mgl(-1), with NOEC and LOEC of 9.75+/-0.34 and 12.84+/-0.34 mgl(-1), respectively. Behavioral aberrations were also noted in this acute toxicity study, including the occurrence of whirling movement and lethargic behavior. The acute effects of RDX on survival, incidence of deformities, and behavior of larval zebrafish occurred at the high end of the most frequently reported concentrations of RDX in aquatic environments. The chronic effects of RDX in aquatic vertebrates need to be determined for an adequate assessment of the ecological risk of environmental RDX.     

Treatment of chemical mechanical polishing wastewater by electrocoagulation: system performances and sludge settling characteristics

Treatment of copper chemical mechanical polishing (CMP) wastewater from a semiconductor plant by electrocoagulation is investigated. The CMP wastewater was characterized by high suspended solids (SS) content, high turbidity (NTU), chemical oxygen demand (COD) concentration up to 500 mgl(-1) and copper concentration up to 100 mgl(-1). In the present study, electrocoagulation was employed to treat the CMP wastewater with an attempt to simultaneously lower its turbidity, copper and COD concentrations. The test results indicated that electrocoagulation with Al/Fe electrode pair was very efficient and able to achieve 99% copper ion and 96.5% turbidity removal in less than 30 min. The COD removal obtained in the treatment was better than 85%, with an effluent COD below 100 mgl(-1). The effluent wastewater was very clear and its quality exceeded the direct discharge standard. In addition, sludge settling velocities after electrocoagulation were measured and the data were employed to verify the empirical sludge settling velocity models. Finally, the sludge settling characteristic data were also utilized to establish the relation between the solids flux (G) and the initial solids concentration.     

Impacts of quicklime (CaO) on the toxicity of copper (CuSO4, 5H2O) to fish and fish food organisms

Static bioassays of 96 h duration were conducted in the laboratory using fry of common carp (Cyprinus carpio), adult tubificid worm (Branchiura sowerbyi) and adult copepod plankton (Cyclops viridis) to determine LC50 values of Cu and CaO to these organisms and effects of interaction between Cu and CaO. Ninety-six hour LC(50) values of Cu to fry of common carp, worm and copepod were found to be 1.40 mgl(-1), 0.08 mgl(-1) and 0.03 mgl(-1) respectively. CaO up to 500 mgl(-1) did not produce any mortality of the fry of common carp up to 96 h. But 96 h LC50 values of CaO to worm and copepod were 83.00 mgl(-1) and 27.80 mgl(-1) respectively. When common carp fry, worm and the copepod were exposed to respective LC50 dose of Cu in presence of varying concentration of CaO, mortality of the organisms significantly reduced and was found inversely correlated with the doses of CaO [y = 48.36-0.807x, r = -0.99 (n = 7) for fish; y = 44.46-0.146x, r = -0.97 (n = 7) for worm; y = 49.46-0.66x, r = -0.99 (n = 7) for the copepod]. The present results indicate that CaO is non-toxic to fish and is capable of reducing the toxicity of Cu to fish while CaO and Cu are antagonistic to each other for the worm and the copepod. Potential of using CaO as antitoxic agent for Cu in water is discussed.     

Investigation of triclosan fate and toxicity in continuous-flow activated sludge systems

The purpose of this research was to study the fate and toxicity of triclosan (TCS) in activated sludge systems and to investigate the role of biodegradation and sorption on its removal. Two continuous-flow activated sludge systems were used; one system was used as a control, while the other received TCS concentrations equal to 0.5 and 2mgl(-1). At the end of the experiment, 1mgl(-1) TCS was added in the control system to investigate TCS behaviour and effects on non-acclimatized biomass. For all concentrations tested, more than 90% of the added TCS was removed during the activated sludge process. Determination of TCS in the dissolved and particulate phase and calculation of its mass flux revealed that TCS was mainly biodegraded. Activated sludge ability to biodegrade TCS depended on biomass acclimatization and resulted in a mean biodegradation of 97%. Experiments with batch and continuous-flow systems revealed that TCS is rapidly sorbed on the suspended solids and afterwards, direct biodegradation of sorbed TCS is performed. Regarding TCS effects on activated sludge process, addition of 0.5mgl(-1) TCS on non-acclimatized biomass initially deteriorated ammonia removal and nitrification capacity. After acclimatization of biomass, nitrification was fully recovered and further increase of TCS to 2mgl(-1) did not affect the performance of activated sludge system. The effect of TCS on organic substrate removal was minor for concentrations up to 2mgl(-1), indicating that heterotrophic microorganisms are less sensitive to TCS than nitrifiers.     

Settling characteristics of nursery pig manure and nutrient estimation by the hydrometer method

The hydrometer method to measure manure specific gravity and subsequently relate it to manure nutrient contents was examined in this study. It was found that this method might be improved in estimation accuracy if only manure from a single growth stage of pigs was used (e.g., nursery pig manure used here). The total solids (TS) content of the test manure was well correlated with the total nitrogen (TN) and total phosphorus (TP) concentrations in the manure, with highly significant correlation coefficients of 0.9944 and 0.9873, respectively. Also observed were good linear correlations between the TN and TP contents and the manure specific gravity (correlation coefficients: 0.9836 and 0.9843, respectively). These correlations were much better than those reported by past researchers, in which lumped data for pigs at different growing stages were used. It may therefore be inferred that developing different linear equations for pigs at different ages should improve the accuracy in manure nutrient estimation using a hydrometer. Also, the error of using the hydrometer method to estimate manure TN and TP was found to increase, from +/- 10% to +/- 50%, with the decrease in TN (from 700 ppm to 100 ppm) and TP (from 130 ppm to 30 ppm) concentrations in the manure. The estimation errors for TN and TP may be larger than 50% if the total solids content is below 0.5%. In addition, the rapid settling of solids has long been considered characteristic of swine manure; however, in this study, the solids settling property appeared to be quite poor for nursery pig manure in that no conspicuous settling occurred after the manure was left statically for 5 hours. This information has not been reported elsewhere in the literature and may need further research to verify.     

Stability of Tylosin A in manure containing test systems determined by high performance liquid chromatography

Tylosin is a widely used antibiotic for the treatment of infections in swine. Tylosin consists of a mixture of Tylosin A, Tylosin B, Tylosin C and Tylosin D. All components contribute to the potency of tylosin but Tylosin A is by far the major component (usually about 90% and not less than 80%). A fast, robust and easily performed HPLC method has been developed for determination of Tylosin A in the presence of tylosin residues; Tylosin B, Tylosin C and Tylosin D in manure containing incubation media. The separation was performed using a YMC-Pack ODS-AQ column (250 x 4.6 mm i.d., 5 microns particle size) operated at 35 degrees C. The mobile phase consisted of 2.25% (w/v) sodium perchlorate pH 2.5-acetonitrile (60:40 v/v). Detection was performed by measuring the UV absorption at a wavelength of 290 nm. Calibration curves of tylosin made in the incubation medium containing 6.4% manure were linear in the range from 0.375 to 128.0 mg/l (R2 = 0.999). The limit of quantitation (at the RSD 20% level) for Tylosin A was found to be 0.4 mg/l in incubation media containing 6.4% manure. The recovery of Tylosin A was in the range from 100% to 108% depending on the concentration of manure. The reproducibility was good as the relative standard deviation (n = 4) in each matrix tested was in the range from 0.7 to 1.9 at the 25 mg/l level. The stability of Tylosin A was studied under methanogenic conditions and the half-life was found to be less than two days. Studies under aerobic conditions showed that the degradation rate was found to increase with increasing concentrations of manure particles in the incubation medium. It is, however, not clear whether the decrease in the concentration of Tylosin A is caused by sorption, abiotic or biotic chemical degradation. The major degradation product of Tylosin A in methanogenic as well as aerobic incubation media has a UV-spectrum and a retention time corresponding to Tylosin B. Furthermore, Tylosin D is believed to be a minor degradation product.     

Nutrient run-off following application of livestock wastes to grassland

Three types of farm waste (cattle slurry, dirty water and farm yard manure (FYM)) were applied to hydrologically isolated grassland plots on a sloping poorly draining soil. Two applications were made, the first in October and the second in February. Application rates were 50 m(3) ha(-1) of slurry and dirty water and 50 t ha(-1) of FYM. Volumes of run-off following rainfall events and concentrations of N, P and K in run-off were measured. Losses of nutrients were higher following applications made with the soil at field capacity and rainfall soon after application. In terms of percentage loss of applied nutrients, losses were generally low. Concentration of N in run-off from the dirty water and FYM treated plots following the first application and the slurry treated plots following the second application exceeded 11.3 mg dm(-3) (a recommended limit for drinking water) although the maximum concentration recorded was 15 mg dm(-3) following FYM application. Concentration of P in run-off only exceeded 1 mg dm(-3) following the second application of cattle slurry. Concentration of K exceeded 10 mg dm(-3) following the first application of FYM and the second application of cattle slurry.     

Dissipation of sulfosulfuron in water - bioaccumulation of residues in fish - LC-MS/MS-ESI identification and quantification of metabolites

Dissipation study of sulfosulfuron in natural water and its bioaccumulation in fish was conducted at 25+/-2 degrees C and at two different concentration levels 1mgl(-1) and 2mgl(-1). The dissipation data in water showed the DT50 and DT90 values 67-76 and 222-253 days and followed first order kinetics. Bioaccumulation of sulfosulfuron in fish was conducted under static conditions exposing the fish at one-tenth of sub-lethal concentration 9mgl(-1) and at double the concentration 18mgl(-1), for a period of 56 days. On different occasions fish samples were collected and analyzed. A HPLC-RF method was used for the quantification of sulfosulfuron and aminopyrimidine with the limit of quantification 0.001microg ml(-1). Results showed the accumulation of residues of sulfosulfuron in fish over the concentration range 0.009-0.496microg g(-1). Both in water and fish samples, identified the presence of metabolites aminopyrimidine, desmethyl sulfosulfuron, guanidine, sulfonamide, ethyl sulfone and rearranged amine. The formations of these metabolites are confirmed by LC-MS/MS analysis. An LC-MS/MS electro spray ionization technique was used for this purpose. One of the metabolite Aminopyrimidine was identified at higher concentration levels (0.01-0.1microg ml(-1)) when compared with other metabolites. Subsequently dissipation of aminopyrimidine in water and its bioaccumulation was also studied at the concentration level 1mgl(-1) and 2mgl(-1). The calculated DT50 and DT90 values are 66-68 days and 218-226 days, respectively. This followed first order kinetics. Three hundred days after the exposure complete demineralization was observed.     

Acetamiprid, carbendazim, diuron and thiamethoxam sorption in two Brazilian tropical soils

Sorption of acetamiprid ((E)-N1-[(6-chloro-3-pyridyl)methyl]-N2-cyano-N1-methylacetamidine), carbendazim (methyl benzimidazol-2-ylcarbamate), diuron (N-(3,4-dichlorophenyl)-N, N-dimethyl urea) and thiamethoxam (3-(2-chloro-thiazol-5-ylmethyl)-5-methyl-[1,3,5]oxadiazinan-4-ylidene-N-nitroamine) was evaluated in two Brazilian tropical soils, Oxisol and Entisol, from Primavera do Leste region, Mato Grosso State, Brazil. To describe the sorption process, batch experiments were carried out. Linear and Freundlich isotherm models were used to calculate the K(d) and K(f) coefficients from experimental data. The K(d) values were utilized to calculate the partition coefficient normalized to soil organic carbon (K(oc)). For the pesticides acetamiprid, carbendazim, diuron and thiamenthoxan the K(oc) (mL g(- 1)) values ranged in both soils from 98 - 3235, 1024 - 2644, 145 - 2631 and 104 - 2877, respectively. From the studied pesticides, only carbendazim presented correlation (r(2) = 0.82 and p < 0.01) with soil organic carbon (OC) content. Acetamiprid and thiamethoxam showed low sorption coefficients, representing a high risk of surface and ground water contamination.