Lignin Functionalized by Thermally Curable Propargyl Groups as Heat-Resistant Polymeric Material

Lignin was chemically functionalized via Williamson etherification reaction with propargyl bromide to prepare a thermosetting bio-resin, propargyllignin. The optimum reaction conditions were found at 70?°C for 4?h under the catalysis of sodium hydroxide in the ethanol solution. The propargllignin resin had highly improved processing capability, evidenced by good solubility, low melting point (<100?°C) and thermal curability. Upon heating, propargyllignin resin solidified with an exotherm around 180?C280?°C peaking at 240?°C, implying its thermal cure reaction via ethynyl polymerization. Compared with lignin feedstock, the propargyllignin resin showed much higher thermal properties: an onset decomposition temperature of 410?°C and a residue yield of 58?% at 800?°C (for lignin, onset decomposition temperature of 250?°C and residue yield of 34?%). Different from the lignin feedstock, propargyllignin was readily applied as curable thermosetting resin for composite matrix, and exhibited high mechanical and thermal properties.     

Recovery of materials from waste printed circuit boards by vacuum pyrolysis and vacuum centrifugal separation

In this research, a two-step process consisting of vacuum pyrolysis and vacuum centrifugal separation was employed to treat waste printed circuit boards (WPCBs). Firstly, WPCBs were pyrolysed under vacuum condition at 600 °C for 30 min in a lab-scale reactor. Then, the obtained pyrolysis residue was heated under vacuum until the solder was melted, and then the molten solder was separated from the pyrolysis residue by the centrifugal force. The results of vacuum pyrolysis showed that the type-A of WPCBs (the base plates of which was made from cellulose paper reinforced phenolic resin) pyrolysed to form an average of 67.97 wt.% residue, 27.73 wt.% oil, and 4.30 wt.% gas; and pyrolysis of the type-B of WPCBs (the base plates of which was made from glass fiber reinforced epoxy resin) led to an average mass balance of 72.20 wt.% residue, 21.45 wt.% oil, and 6.35 wt.% gas. The results of vacuum centrifugal separation showed that the separation of solder was complete when the pyrolysis residue was heated at 400 °C, and the rotating drum was rotated at 1200 rpm for 10 min. The pyrolysis oil and gas can be used as fuel or chemical feedstock after treatment. The pyrolysis residue after solder separation contained various metals, glass fibers and other inorganic materials, which could be recycled for further processing. The recovered solder can be reused directly and it can also be a good resource of lead and tin for refining.     

Pore structure and adsorption properties of carbonized material prepared from waste paper

We have already reported the adsorptivity and pore structure of activated carbon made from waste newspaper in order to use the waste paper for purposes other than paper-making stock. However, manufacturing the activated carbon may not necessarily be an advantageous method based on environmental concerns and the effective use of the resource because the reaction during the activating process is endothermic and the amount of carbon consumed is significant. Here, we examine the pore structure and adsorption properties of waste newspaper used as an adsorbent in the form of a carbonized material. Waste newspaper was carbonized for 2 h in the temperature range 400°–1000°C. The specific surface area of the carbonized material obtained, 418 m²/g, was highest for the sample carbonized at 800°C, which was equal to or greater than that of commercially available charcoal. Moreover, the iodine adsorption number of 581 mg/g was the highest and the rate of adsorption was the fastest for the sample carbonized at 800°C. However, the humidity control capability was highest for the material carbonized at 600°–700°C. It has been determined that it is advantageous to carbonize waste paper at 800°C in order to use the carbonized material as an adsorbent, while carbonization at 600°–700°C is more advantageous for use as a humidity control material. Received: June 23, 2000 / Accepted: January 17, 2001     

Two-stage thermal gasification of polyolefins

Plastic pellets of polyethylene (PE), polypropylene (PP), and polystyrene (PS) were gasified in a two-stage thermal degradation process. The first stage is the conversion of polyolefins to distilled oils using a melting vessel. In the second stage, the oils from the first stage are gasified using a tubular reactor. The distilled oil yields of PE, PP, and PS in the first stage were 84, 89, 92 wt%, respectively, each at 470°C. The total gas yields of PE, PP, and PS in the second stage were 80, 74, and 6.2 wt%, respectively, each at 800°C. The main components of the product gas for PE and PP were methane and olefins such as ethene and propene. Some aromatic oils, including benzene, toluene, and xylene, were also produced as by-products. The amount of carbonaceous residue, or coke, was very low (less than 1 wt%). By dividing the process into two stages, the coking rate was considerably reduced compared with direct gasification of the polyolefins. Received: July 19, 2000 / Accepted: September 17, 2000     

Bio-oil production by fast pyrolysis of cellulose/polyethylene mixtures in the presence of metal chloride

Cellulose/polyethylene mixture (3:1 w/w) and Tetra Pak wastes with and without metal chloride (ZnCl₂, AlCl₃, CuCl₂, FeCl₃) addition were subjected to a fast pyrolysis process at 350–500 °C and heating rate 100 °C/s to evaluate the possibility of liquid product formation with a high yield. The addition of zinc, aluminum, iron and copper chlorides has influenced the range of samples decomposition as well as the chemical composition of resulting pyrolytic oils. It was found that formation of levoglucosan, the main product of cellulose thermal decomposition, and phenol and its derivatives decreased in a presence of metal chlorides. Non-catalytic fast pyrolysis of polyethylene leads to the formation of solid long chain hydrocarbons, whereas the addition of metal chlorides promotes the formation of more liquid hydrocarbons.     

Studies on the dechlorination and oil-production technology of waste plastics

 Recycle technology for waste plastics containing polyvinyl chloride (PVC) has been developed in the Hokkaido National Industrial Research Institute for the production of solid and liquid fuel, and has established a recycling process which includes a dechlorination process for PVC plastics, and a two-stage catalytic pyrolysis process for plastics using zeolite catalysts. The dechlorination equipment consists of a two-axis screw extruder with a heating element, which can remove chlorine up to 99.9 wt. % from PVC containing plastics as hydrogen chloride. The product had about 44 000 kJ/kg calorific value and was fed into the next oil production process, although it could also be used as a solid fuel. Natural and synthetic zeolite were used as catalysts for the two-stage catalytic process, which produced a light oil with a boiling point which was between those of kerosene and gasoline. The yield of this oil reached 82 wt. %. The chemical type was analyzed using liquid chromatography, and was found to have many aromatic compounds. These technologies make it possible to produce a nonpolluting, high-calorie solid fuel and a liquid fuel very efficiently. Received: July 19, 2000 / Accepted: September 21, 2000     

Characterization of products obtained from pyrolysis and steam gasification of wood waste,RDF, and RPF

Pyrolysis and steam gasification of woody biomass chip (WBC) obtained from construction and demolition wastes, refuse-derived fuel (RDF), and refuse paper and plastic fuel (RPF) were performed at various temperatures using a lab-scale instrument. The gas, liquid, and solid products were examined to determine their generation amounts, properties, and the carbon balance between raw material and products.The amount of product gas and its hydrogen concentration showed a considerable difference depending on pyrolysis and steam gasification at higher temperature. The reaction of steam and solid product, char, contributed to an increase in gas amount and hydrogen concentration. The amount of liquid products generated greatly depended on temperature rather than pyrolysis or steam gasification. The compositions of liquid product varied relying on raw materials used at 500 °C but the polycyclic aromatic hydrocarbons became the major compounds at 900 °C irrespective of the raw materials used. Almost fixed carbon (FC) of raw materials remained as solid products under pyrolysis condition whereas FC started to decompose at 700 °C under steam gasification condition.For WBC, both char utilization by pyrolysis at low temperature (500 °C) and syngas recovery by steam gasification at higher temperature (900 °C) might be practical options. From the results of carbon balance of RDF and RPF, it was confirmed that the carbon conversion to liquid products conspicuously increased as the amount of plastic increased in the raw material. To recover feedstock from RPF, pyrolysis for oil recovery at low temperature (500 °C) might be one of viable options. Steam gasification at 900 °C could be an option but the method of tar reforming (e.g. catalyst utilization) should be considered.     

Catalytic conversion of waste tyres into valuable hydrocarbons

Tyre recycling has become a necessity because of the huge piles of tyres that represent a threat to the environment. The used tyres represent a source of energy and valuable chemical products. Waste tyres were pyrolysed catalytically in a batch reactor under atmospheric pressure. Calcium carbide was used as a catalyst to explore its effect on pyrolysis product distribution. The effect of temperature, amount of catalyst and time on the yields of the pyrolysed products was investigated. Char yield decreased with increase of pyrolysis temperature while total gas and liquid yields increased. The liquid fraction was obtained with boiling point up to 320 °C. The physical and chemical properties of the pyrolysed products obtained were characterized. The catalytic pyrolysis produced 45 wt.% aromatic, 35 wt.% aliphatic and 20 wt.% of polar hydrocarbons. The distillation data showed that ∼80% of oil has boiling point below 270 °C which is the boiling point for 50% of distilled product in commercial diesel oil. The oil fraction was found to have high gross calorific value; GCV (42.8 MJ kg⁻¹). Its Specific gravity, viscosity, Kinematic viscosity, freezing point and diesel index were also within the limits of diesel fuel. The char residues were studied to investigate their characteristics for use as a possible adsorbent. Surface area of char before and after acid demineralization was determined to determine the adsorptive features for waste water treatment.     

Production of hydrogen by steam gasification of dehydrochlorinated poly(vinyl chloride) or activated carbon in the presence of various alkali compounds

Steam gasification of dehydrochlorinated poly(vinyl chloride) (PVC) or activated carbon was carried out in the presence of various alkali compounds at 3.0 MPa and 560°C–660°C in a batch reactor or in a semi-batch reactor with a flow of nitrogen and steam. Hydrogen and sodium carbonate were the main products, and methane and carbon dioxide were the minor products. Yields of hydrogen were high in the presence of sodium hydroxide and potassium hydroxide. The acceleration effect of the alkali compounds on the gasification reaction was as follows: KOH > NaOH > Ca(OH)₂ > Na₂CO₃. The rate of gasification increased with increasing partial steam pressure and NaOH/C molar ratio. However, the rate became saturated at a molar ratio of NaOH/C greater than 2.0.     

Effect of Solvent Composition on Porosity,Surface Morphology and Thermal Behavior of Metal Alginate Prepared from Algae (<Emphasis Type="Italic">Undaria pinnatifida</Emphasis>)

Alginates, extracted from algae are linear unbranched polymers containing β-(1→4)-linked d-mannuronic acid (M) and α-(1→4)-linked l-guluronic acid (G) residues. The conversion of alginic acid into the metal alginate is confirmed using FTIR spectroscopy. Asymmetric and symmetric stretching of free carboxyl group present in metal alginate occurs almost at the same position in various solvent compositions. Total intrusion volume of metal alginate prepared in propanol (0.0742 mL/g) is greater compared to those in ethanol (0.0648 mL/g) and methanol (0.0393 mL/g) as solvent. Surface morphology as well as porosity and pore size distribution of metal alginate are greatly influenced by solvent. It can be seen from thermal analysis results that calcium alginate prepared using different solvent compositions started decomposing at 100 °C, but rapid degradation started around 200 °C. The results showed a stepwise weight loss during thermal sweep, indicating different types of reactions during degradation. First and second step of rapid degradation was situated around 200–300 and 300–550 °C, respectively; whereas the final step is situated around 550–650 °C. The trend of degradation was similar for all the solvents, although the amount of final residue varied from one solvent to another. At the same time, lower thermal stability was also observed with higher heating rates. Additionally, a kinetic analysis was performed to fit with TGA data, where the entire degradation process has been considered as three consecutive first order reactions.     

Using liquid waste streams as the moisture source during the hydrothermal carbonization of municipal solid wastes

Hydrothermal carbonization (HTC) is a thermal conversion process that can be an environmentally beneficial approach for the conversion of municipal solid wastes to value-added products. The influence of using activated sludge and landfill leachate as initial moisture sources during the carbonization of paper, food waste and yard waste over time at 250 °C was evaluated. Results from batch experiments indicate that the use of activated sludge and landfill leachate are acceptable alternative supplemental liquid sources, ultimately imparting minimal impact on carbonization product characteristics and yields. Regression results indicate that the initial carbon content of the feedstock is more influential than any of the characteristics of the initial liquid source and is statistically significant when describing the relationship associated with all evaluated carbonization products. Initial liquid-phase characteristics are only statistically significant when describing the solids energy content and the mass of carbon in the gas-phase. The use of these alternative liquid sources has the potential to greatly increase the sustainability of the carbonization process. A life cycle assessment is required to quantify the benefits associated with using these alternative liquid sources.     

Co-processing of DVDs and CDs with vegetable cooking oil by thermal degradation

Waste DVDs and CDs were thermally degraded at 450°C by a semibatch process. In total, 40–50 wt% was converted into liquid product that consisted of phenol derivatives (∼75 wt%), bisphenol (∼10 wt%) and its derivatives, and small amounts of aromatic hydrocarbons such as benzene, toluene, ethylbenzene, dimethylbenzene, methylethylbenzene, diethylbenzene, and methylisopropyl benzene. Degradation of the polycarbonate support from DVDs and CDs was enhanced by coprocessing with vegetable cooking oil, the degradation of which gave a homologue series of hydrocarbons and organic acids with up to 25 and 18 atoms of carbon, respectively. Silver from the reflective coating on DVDs and CDs remained in the solid residue, its concentration increasing about 2.5 times compared to that of the original disks.     

Effect of thermal pretreatment on the physical and chemical properties of municipal biomass waste

The effects of thermal pretreatment on the physical and chemical properties of three typical municipal biomass wastes (MBWs), kitchen waste (KW), vegetable/fruit residue (VFR), and waste activated sludge (WAS) were investigated. The results show that thermal pretreatment at 175 °C/60 min significantly decreases viscosity, improves the MBW dewatering performance, as well as increases soluble chemical oxygen demand, soluble sugar, soluble protein, and especially organic compounds with molecular weights >10 kDa. For KW, VFR and WAS, 59.7%, 58.5% and 25.2% of the organic compounds can be separated in the liquid phase after thermal treatment. WAS achieves a 34.8% methane potential increase and a doubled methane production rate after thermal pretreatment. In contrast, KW and VFR show 7.9% and 11.7% methane decrease because of melanoidin production.     

Debromination of flame-retarded TV housing plastic waste

The thermal stability and degradation kinetics of TV housing plastic and brominated flame retardants were studied by means of thermogravimetry. The effects of the treatment temperature on the removal rate of Br were investigated using a tube furnace reactor under isothermal and vacuum conditions. The results showed that the weight loss of TV housing plastic was divided into two stages: the thermal degradation of brominated flame retardants mainly occurred at 290°–350°C, and the degradation of the high-impact polystyrene resin mainly occurred at 350°–455°C. Nearly 90% of Br can be removed from TV housing plastic when the treatment temperature exceeds 280°C.     

Co-gasification of wood and polyethylene with the aim of CO and H2 production

This article describes the gasification of polyethylene–wood mixtures to form syngas (H₂ and CO) with the aim of feedstock recycling via direct fermentation of syngas to ethanol. The aim was to determine the effects of four process parameters on process properties that give insight into the efficiency of gasification in general, and particularly into the optimum gasification conditions for the production of ethanol by fermentation of producer gas. Gasification experiments (fluidized bed, 800°–950°C) were done under different conditions to optimize the composition of syngas suitable for fermentation purposes. The data obtained were used for statistical analysis and modeling. In this way, the effect of each parameter on the process properties was determined and the model was used to predict the optimum gasification conditions. The parameters varied during the experiment were gasification temperature, equivalence ratio, the ratio of plastic to wood in the feed, and the amount of steam added to the process. The response models obtained proved to be statistically significant in the experimental domain. The optimum gasification conditions for maximization of carbon monoxide and hydrogen production were identified. The conditions are: temperature 900°C, equivalence ratio 0.15, amount of plastic in the feed 0.11 g/g feed, and amount of steam added 0.42 g/g feed. These optimum conditions are at the edge of the present experimental domain. The maximum combined CO and H₂ efficiency was 42%, and for the maximum yield of CO and H₂ it is necessary to minimize the polyethylene content, minimize the added steam and the equivalence ratio, and maximize temperature.     

Synthesis of hydrogarnet from molten slag and its hydrogen chloride fixation performance at high temperature

Hydrogarnet was synthesized hydrothermally below 200°C using molten slag obtained from municipal solid waste. For comparison, it was also synthesized using pure-phase CaO–Al₂O₃–SiO₂–H₂O, as reported previously. The structural and textural properties of this material were investigated using various analytical and spectroscopic techniques such as X-ray diffraction, X-ray fluorescence spectrometry, atomic absorption spectrometry (AAS), thermogravimetry/differential thermal analysis, Fourier transform infrared spectroscopy, and scanning electron microscopy. The Cl⁻ fixation ability of hydrogarnet was investigated in the temperature range 500–800°C in a fixed-bed flow reactor using a HCl concentration (1000 p.p.m.v.) similar to that of incinerator exhaust gas. Under these experimental conditions, the hydrogarnet was capable of reducing the HCl gas level to less than 1 p.p.m.v. Analysis of the spent catalyst revealed that the hydrogarnet was being transformed into wadalite and CaCl₂ at high temperatures. The elution test for chromium ions in hydrogarnet obtained from slag was also used, and it was found that chromium ions were not eluted from hydrogarnet. Received: January 27, 2001 / Accepted: October 11, 2001     

Dechlorination of polyvinyl chloride in NaOH/ethylene glycol solution by microwave heating

This study investigated the dehydrochlorination of flexible polyvinyl chloride (PVC) containing 59.2% PVC, 29.7% dioctyl phthalate (DOP), and approximately 12% stabilizers. Flexible PVC was treated with NaOH/ethylene glycol (NaOH/EG) solutions at NaOH concentrations in the range 0.5–4 mol/l and was heated in a microwave heater at a temperature between 100° and 160°C for 0–30 min. All chlorides were completely eliminated by internal heating at 160°C using microwaves for 10 min in a 1 mol/l NaOH/EG solution, and the residue was made up of hydrocarbons. The weight loss rate reached a maximum of 74.7% at a temperature of 160°C. It was discovered that the use of microwaves significantly shortened the reaction time compared to using conventional electric heaters or other external heating systems and also allowed the use of lower concentrations of NaOH. Chemical Feedstock Recycling & Other Innovative Recycling Techniques 6     

Pyrolysis of waste animal fats in a fixed-bed reactor: Production and characterization of bio-oil and bio-char

Several animal (lamb, poultry and swine) fatty wastes were pyrolyzed under nitrogen, in a laboratory scale fixed-bed reactor and the main products (liquid bio-oil, solid bio-char and syngas) were obtained. The purpose of this study is to produce and characterize bio-oil and bio-char obtained from pyrolysis of animal fatty wastes. The maximum production of bio-oil was achieved at a pyrolysis temperature of 500 °C and a heating rate of 5 °C/min. The chemical (GC–MS analyses) and spectroscopic analyses (FTIR analyses) of bio-oil showed that it is a complex mixture consisting of different classes of organic compounds, i.e., hydrocarbons (alkanes, alkenes, cyclic compounds…etc.), carboxylic acids, aldehydes, ketones, esters,…etc. According to fuel properties, produced bio-oils showed good properties, suitable for its use as an engine fuel or as a potential source for synthetic fuels and chemical feedstock. Obtained bio-chars had low carbon content and high ash content which make them unattractive for as renewable source energy.     

Hydrothermal carbonization of food waste and associated packaging materials for energy source generation

Hydrothermal carbonization (HTC) is a thermal conversion technique that converts food wastes and associated packaging materials to a valuable, energy-rich resource. Food waste collected from local restaurants was carbonized over time at different temperatures (225, 250 and 275 °C) and solids concentrations to determine how process conditions influence carbonization product properties and composition. Experiments were also conducted to determine the influence of packaging material on food waste carbonization. Results indicate the majority of initial carbon remains integrated within the solid-phase at the solids concentrations and reaction temperatures evaluated. Initial solids concentration influences carbon distribution because of increased compound solubilization, while changes in reaction temperature imparted little change on carbon distribution. The presence of packaging materials significantly influences the energy content of the recovered solids. As the proportion of packaging materials increase, the energy content of recovered solids decreases because of the low energetic retention associated with the packaging materials. HTC results in net positive energy balances at all conditions, except at a 5% (dry wt.) solids concentration. Carbonization of food waste and associated packaging materials also results in net positive balances, but energy needs for solids post-processing are significant. Advantages associated with carbonization are not fully realized when only evaluating process energetics. A more detailed life cycle assessment is needed for a more complete comparison of processes.     

Improved quartz furnace method for chlorine and sulfur determination in municipal solid waste

 A method of determining the chlorine (Cl) and sulfur (S) in municipal solid waste (MSW) was studied. The quartz furnace method was improved in two ways: recovery from ash by hot extraction with dilute nitric acid, and avoidance of the volatilization of alkali (earth) metal chlorides by setting the sample combustion temperature at 600°C. In a comparison with the bomb method, using nine sets of kitchen garbage and waste plastics, the bomb method yielded a 15%–25% lower value than the improved quartz furnace method. Combustion in the bomb was frequently incomplete, resulting in recovery losses of Cl and S. The average kitchen garbage involved 5.2 mg Cl/g, of which at least 24.1% would be converted to HCl. Plastics contained 23 mg Cl/g generating 88.1% HCl on average. In the same way, kitchen garbage contained 3.0 mg S/g, generating 52.3% SO _x , whereas plastics contained 1.1 mg S/g with 55.1% SO _x formation. Received: March 20, 2002 / Accepted: October 13, 2002