Stabilization and solidification of elemental mercury for safe disposal and/or long-term storage

A simple and highly effective stabilization/solidification (S/S) technology of elemental mercury using only sulfur with paraffin is introduced. First, elemental mercury is mixed with an excess of sulfur powder and heated to 60 degrees C for 30 min until elemental mercury is converted into mercuric sulfide (HgS black, metacinnabar) (Step 1). Then, metacinnabar with additional sulfur is poured into liquid paraffin (Step 2). Finally, the mixture is melted at 140 degrees C and settles to the bottom of the vessel where it cools and solidifies under the layer of liquid paraffin (Step 3). The proposed S/S method with sodium sulfide nonahydrate (Na2S x 9H2O) as an additive is also tested for comparison. The average toxicity characteristic leaching procedure test values are 6.72 microg/L (no additive) and 3.18 microg/L (with additive). Theses concentrations are well below the Universal Treatment Standard (25 microg/L). Effective diffusion coefficient evaluated from accelerated leach test and average headspace concentration of Hg vapor after 18 hr are 3.62 x 10(-15) cm2/sec, 0.55 mg/m3 (no additive) and 5.86 x 10(-13) cm2/sec, 0.25 mg/m3 (with additive).     

Mercury Measurement and Its Control: What We Know,Have Learned,and Need to Further Investigate

Disposal of mercury waste has always provided unique challenges due to its high degree of complexity and volatility. This study evaluated the feasibility of using waste LF slag to form a cementitious matrix capable of providing an effective stabilization/solidification solution for the treatment of mercury wastes. The new matrix was synthesized and simulated through a combination of alkali activation and autoclaving process and doped with mercury nitrate at increasing dosage while monitoring the final form of the mercury and its effects on the mineral stability and structure of the new matrix. Compressive strength of up to 20 N/mm² was achievable for the original matrix. Promising results were obtained in terms of reduced leachability of the mercury when compared to ordinary Portland cement systems at low doping concentration of around 0.5% by weight. A series of precipitation reactions was found to be the main cause responsible for this successful stabilization, especially the metal sulfide precipitation that occurred with the sulfur present in the original waste LF slag.

Implications: Using waste to treat waste as a concept is a new approach that not only solves waste disposal problems but also minimizes the toxicity and the potential hazard of leaching of heavy metals. This study evaluated the feasibility of using waste ladle furnace slag generated from steel-making industries to form a cementitious matrix capable of providing an effective stabilization/solidification solution for the treatment of mercury-containing wastes. Promising results were obtained, and it clearly showed this approach is feasible, which could be a one-stone-kills-two-birds solution for mercury stabilization as well as an industrial waste disposal problem.     

pH对污水污泥中污染物浸出的影响

研究pH对污泥中污染物浸出的影响可以为投海过程中海洋水体酸碱性变化对污泥中污染物浸出的影响及其变化规律提供理论依据。为了得出不同pH值对污泥中污染物浸出的影响,采用CEN/TS 14429：2005浸出实验对上海5个污水处理厂脱水污泥中重金属、溶解性有机碳、溶解性硫化物和主要离子的浸出情况进行了研究,同时分别以超纯水和海水为浸提剂研究在相应pH范围内盐度对上述指标浸出的影响。结果表明,Zn、Cd、Pb和As在酸性和碱性条件下浸出量较高,在中性或接近中性条件下浸出量则最低,且海水中Zn和Cd的浸出量比超纯水中高;Cu在碱性条件下的浸出量明显比酸性条件高;在所研究的pH范围内,5个污泥样品中溶解性有机碳的浸出量均随pH的升高而增高;仅酸挥发性硫含量最高的S5在海水中有较明显的溶解性硫化物浸出;部分污泥样品中的氮在酸性纯水中有较高的浸出量,海水中浸出量较少;而无论海水或纯水中,磷在强酸和强碱条件下均有明显浸出。     

Mercury exposure in the freshwater tilapia Oreochromis niloticus

Mercury (Hg) can be strongly accumulated and biomagnified along aquatic food chain, but the exposure pathway remains little studied. In this study, we quantified the uptake and elimination of both inorganic mercury [as Hg(II)] and methylmercury (as MeHg) in an important farmed freshwater fish, the tilapia Oreochromis niloticus, using ²⁰³Hg radiotracer technique. The dissolved uptake rates of both mercury species increased linearly with Hg concentration (tested at ng/L levels), and the uptake rate constant of MeHg was 4 times higher than that of Hg(II). Dissolved uptake of mercury was highly dependent on the water pH and dissolved organic carbon concentration. The dietborne assimilation efficiency of MeHg was 3.7-7.2 times higher than that of Hg(II), while the efflux rate constant of MeHg was 7.1 times lower. The biokinetic modeling results showed that MeHg was the greater contributor to the overall mercury bioaccumulation and dietary exposure was the predominant pathway.     

Catalytic reduction of sulfur dioxide with carbon monoxide over tin dioxide for direct sulfur recovery process

SO(2) reduction by CO over SnO(2) catalyst was studied in this work. The parameters were the reaction temperature, space velocity (GHSV) and [CO]/[SO(2)] molar ratio. The optimal temperature, GHSV and [CO]/[SO(2)] molar ratio were 550 degrees C, 8000 h(-1) and 2.0, respectively. Under these conditions, the SO(2) conversion and sulfur selectivity were about 78% and 68%, respectively. The following reaction pathway involving two mechanisms was proposed in SO(2) reduction by CO over SnO(2) catalyst: in the first step involving Redox mechanism, the elemental sulfur was produced by the mobility of the lattice oxygen between SO(2) and SnO(2) surface. In the second step, COS was formed by the side reaction between elemental sulfur and CO or metal sulfide and CO. In the third step involving COS intermediate mechanism, the abundant elemental sulfur was produced by the SO(2) reduction by COS which was produced in the second step and was more effective reducing agent than CO.     

Sorption of mercury (II) in Amazon soils from column studies

The sorption of Hg (II) onto four different types of Amazon soils from the A-horizon was investigated by means of column experiments under saturation conditions and controlled metal load. Higher organic matter contents in the soil resulted in higher Hg (II) adsorptions, reaching values as high as 3.8 mg Hg g⁻¹ soil. The amount of mercury adsorbed on a soil column (Q) shows a very poor correlation with soil clay content (r² = 0.2527), indicating that Hg sorption in these topsoil samples is chiefly governed by the organic matter content. Desorption experiments using Negro River (Amazon) waters were conducted using soil saturated with Hg (II) in order to better understand the metal leaching mechanism. The amount of Hg (II) released from soils was around 30% of the total sorbed mercury upon saturation, suggesting that mercury sorption in the soils present in the catchment area of the Negro River basin is not a reversible process.     

Selenium,total mercury and methylmercury in sardine: Study of molar ratio and protective effect on the diet

The purpose of this work was to evaluate the risk-benefit associated with canned sardine consumption, considering the selenium, the mercury and the methylmercury contents and the Se:Hg molar ratio and the Se-health benefit value (HBV) index. In this study, 63 canned sardine samples were purchased worldwide and for the determination of selenium and mercury species, the inductively coupled plasma optical emission spectrometry and thermal decomposition and amalgamation atomic absorption spectrometry were employed. The mean results obtained for the Brazilian samples varied between 12.6 and 65.5?μg kg^?1 for Hg; <3.7 and 45.4?μg kg^?1 for methylmercury; 310 and 1370?μg kg^?1 for Se. The MeHg/Hg ratio showed that the most toxic forms of Hg (MeHg) is predominant in 52 and 39% of the Brazilian samples conserved in tomato sauce and in oil, respectively. Nevertheless, the Se-HBV index and the Hg:Se and Se:Hg molar ratios indicated that the selenium content in canned sardine samples is enough to provide a protective effect on the Hg species.     

Specific accumulation of mercury and selenium in seabirds

Total mercury (T-Hg), methyl mercury (MeHg) and selenium (Se) concentrations were determined to elucidate the relationship between Hg and Se levels in the liver of 10 seabird species. Highest concentrations of T-Hg (mean 267 microg/g dry wt), MeHg (mean 25.5 microg/g dry wt) and Se (mean 113 microg/g dry wt) were in the liver of black-footed albatross (Diomedea nigripes). An equivalent molar ratio of 1:1 between T-Hg and Se was found in the liver of individuals which contain over 100 microg Hg/g. However, such a relationship was unclear in other individuals which had relatively low Hg levels. This suggests that Se plays a role in Hg detoxification for those individuals with high Hg. In seabird tissues, Hg and Se levels should be a most important factor determining the relationship between Hg and Se, and fluctuation of Hg burden through molting and the species-specific demethylation capacity would also influence their relationships.     

Sorption studies of heavy metal ions on a novel chelating resin and its application in the stripping of mercury (II)

A chelating resin containing a stable thiol group was synthesised, using polystyrene as the starting material. The resin is stable towards conc. HCl, 0.1M HNO(3) and 0.1M NaOH. The resin shows affinity towards Ag(+), Hg(2+), Bi(3+), Pb(2+), Cu(2+), Zn(2+) and Cd(2+). Extraction of these metal ions as a function of pH, kinetics of exchange and breakthrough capacities is evaluated. The selectivity of the resin for the metal ions is in the order Ag(+) > Hg2+ > Cu2+ > Pb2+ > Cd2+ > Zn2+. The equilibrium constants for exchange and kinetics of exchange are favourable for the recovery of mercury from lean sources. Application of the resin in the stripping of mercury from chlor-alkali plant affluent, and in the enrichment of mercury from seawater, have been investigated. Mercury sorbed resin can be regenerated using 5% thiourea in 0.1M HCl.     

In vitro and in vivo studies of lead immobilization by synthetic hydroxyapatite

Apatite appears a useful compound for removing lead from water, due to its ability to immobilize the metal by precipitation. In dilute solution, dissolved hydroxyapatite [HA, Ca1O(P04)6(OH)2] provided phosphates that were reactive with aqueous lead (molar ratio HA/Pb= 1/10) forming precipitates at around pH 6. These dissolved at a more acidic pH (3). Solid HA in contact with Pb2+ions, led to the formation of pyromorphite [Pblo(P04)6(OH)2], identified by X-ray diffraction and insoluble at pH tested (3-8). The amount of pyromorphite increased with the weight ratio of HA/Pb. When this one increased from 1 to 1000, lead precipitated as pyromorphite rose from 19 to 99%. In vivo experiments on rats confirmed the in vitro results. In fact, lead bioavailability assessed by intestinal perfusion was unchanged in the presence of dissolved HA, whereas it was significantly lower in the presence of solid HA, evaluated by gastric intubation, at a weight ratio equal to 10 (amount of lead absorbed decreased by 60%). Apatite could bean effective means of immobilizing lead in drinking or sewage, since accidental pyromorphite ingestion does not yield bioavailable lead.     

Removal of chromium from abrasive blast media by leaching and electrochemical precipitation

Water is effective in leaching out Cr6+ from a mixture of paint powders and abrasive blast media. However, acids such as HNO3, HCl, and H2SO4 significantly enhance the leaching procedure. Cr ions in the leaching solutions are successfully removed by electrochemical precipitation. The consumable Fe electrodes generate ferrous ions to cause the reduction of Cr6+ to Cr3+. Cr3+ ions along with Fe2+ and Fe3+ are then removed mainly by precipitation as Cr(OH)3, Fe(OH)2, and Fe(OH)3 near the cathode where OH- ions are generated by water electrolysis. The electrochemical process is capable of discharging low levels of Cr6+, less than 1 mg/L, without pH adjustment.     

Stabilization of FGD gypsum for its disposal in landfills using amorphous aluminium oxide as a fluoride retention additive

The applicability of amorphous aluminium oxide as a fluoride retention additive to flue gas desulphurisation (FGD) gypsum was studied as a way of stabilizing this by-product for its disposal in landfills. Using a batch method the sorption behaviour of amorphous aluminium oxide was evaluated at the pH (about 6.5) and background electrolyte conditions (high chloride and sulphate concentrations) found in FGD gypsum leachates. It was found that fluoride sorption on amorphous aluminium oxide was a very fast process with equilibrium attained within the first half an hour of interaction. The sorption process was well described by the Langmuir model, offering a maximum fluoride sorption capacity of 61.7 mg g(-1). Fluoride sorption was unaffected by chloride co-existing ions, while slightly decreased (about 20%) by competing sulphate ions. The use of amorphous aluminium oxide in the stabilization of FGD gypsum proved to greatly decreased its fluoride leachable content (in the range 5-75% for amorphous aluminium oxide doses of 0.1-2%, as determined by the European standard EN 12457-4 [EN-12457-4 Characterization of waste-leaching-compliance test for leaching of granular waste materials and sludges-Part 4: one stage batch test at a liquid to solid ratio of 10 l/kg for materials with particle size below 10mm (without or with size reduction)]), assuring the characterization of this by-product as a waste acceptable at landfills of non-hazardous wastes according to the Council Decision 2003/33/EC [Council Decision 2003/33/EC of 19 December 2002. Establishing criteria and procedures for the acceptance of waste at landfills pursuant to Article 16 of and Annex II to Directive 1999/31/EC] on landfill of wastes. Furthermore, as derived from column leaching studies, the proposed stabilization system proved to be highly effective in simulated conditions of disposal, displaying a fluoride leaching reduction value about 81% for an amorphous aluminium oxide added amount of 2%.     

矿区炼金废渣的固化/稳定化处理

通过对金矿矿区炼金废渣的酸中和能力、净产酸量及浸出毒性实验,测定了废渣的产酸潜力及重金属砷、镉、铅、锌的总量和它们的浸出量。为了合理处置矿区炼金废渣,并为矿区重金属污染土壤的修复提供技术支持,采用石灰、粉煤灰、堆肥化污泥作为添加剂对废渣进行固化/稳定化处理;通过浸出毒性实验对固化/稳定化处理效果进行综合分析,试图寻求一种最佳的稳定剂。结果表明,无论是单独添加石灰、粉煤灰或者堆肥化污泥还是两两组合混合添加,样品浸出液的pH都有升高,As、Cd的浸出浓度都有明显下降,而且两两组合添加比单独添加的固化/稳定化处理效果更好。在两两组合添加中,粉煤灰混合堆肥化污泥的处理效果最好,浸出液的pH值达到7.82,As、Cd的浸出率分别下降72.0%和72.2%。说明粉煤灰混合堆肥化污泥处理炼金废渣效果最佳,同时具有以废治污的资源化生态效能。     

Uptake of atmospheric mercury by deionized water and aqueous solutions of inorganic salts at acidic,neutral and alkaline pH

Mercury (Hg) is well known as a toxic environmental pollutant that is among the most highly bioconcentrated trace metals in the human food chain. The atmosphere is one of the most important media for the environmental cycling of mercury, since it not only receives mercury emitted from natural sources such as volcanoes and soil and water surfaces but also from anthropogenic sources such as fossil fuel combustion, mining and metal smelting. Although atmospheric mercury exists in different physical and chemical forms, as much as 90% can occur as elemental vapour Hg0, depending on the geographic location and time of year. Atmospheric mercury can be deposited to aquatic ecosystems through both wet (rain or snow) and dry (vapour adsorption and particulate deposition) processes. The purpose of the present study was to measure, under laboratory conditions, the rate of deposition of gaseous, elemental mercury (Hg0) to deionized water and to solutions of inorganic salt species of varying ionic strengths with a pH range of 2-12. In deionized water the highest deposition rates occurred at both low (pH 2) and high (pH 12). The addition of different species of salt of various concentrations for the most part had only slight effects on the absorption and retention of atmospheric Hg0. The low pH solutions of various salt concentrations and the high pH solutions of high salt concentrations tested in this study generally showed a greater tendency to absorb and retain atmospheric Hg0 than those at a pH closer to neutral.     

Mercury levels in surface waters of the Carson River-Lahontan Reservoir system, Nevada: Influence of historic mining activities

Total mercury (HgT), methylmercury (MeHg), and other operationally defined Hg species were determined on water samples collected from a river-reservoir system impacted by historic mine wastes. Simultaneously, a comprehensive study was undertaken to determine the influence of some major physico-chemical parameters on the fate of Hg within the system. Total Hg levels showed an increase from background concentrations of 4 ng liter(-1) upstream of mining activity, to peak values of 1500-2100 ng liter(-1) downstream of Hg contaminated mine tailings piles. MeHg concentrations varied from 0.1 to 7 ng liter(-1) in surface waters. In both cases, peak values were associated with the highest concentrations of total suspended solids (TSS). Particulate Hg (HgP) was typically >50% of HgT and increased downstream. The dissolved fraction of MeHg (MeHgD) always constituted a large portion of total methylmercury (MeHgT). The [MeHgT]/[HgT] ratio decreased downstream suggesting either a high percentage of inorganic Hg input from point sources, or low specific rates of MeHg production within the aquatic system. The latter could be due to the combined effects on microbial populations of both high levels of Hg concentrations found in water and sediments, and other factors related to the aqueous geochemistry of the system. Concentrations of HgT in the water column appeared to be enhanced by inputs of contaminated particles from the watershed during spring snow melt. In the reservoir, significant losses of Hg from the water column were observed. In addition to losses of Hg bound to particles by sedimentation, the removal through volatilization of dissolved gaseous Hg could be an important pathway.     

Cork stoppers as an effective sorbent for water treatment: the removal of mercury at environmentally relevant concentrations and conditions

The technical feasibility of using stopper-derived cork as an effective biosorbent towards bivalent mercury at environmentally relevant concentrations and conditions was evaluated in this study. Only 25 mg/L of cork powder was able to achieve 94 % of mercury removal for an initial mercury concentration of 500 μg/L. It was found that under the conditions tested, the efficiency of mercury removal expressed as equilibrium removal percentage does not depend on the amount of cork or its particle size, but is very sensitive to initial metal concentration, with higher removal efficiencies at higher initial concentrations. Ion exchange was identified as one of the mechanisms involved in the sorption of Hg onto cork in the absence of ionic competition. Under ionic competition, stopper-derived cork showed to be extremely effective and selective for mercury in binary mixtures, while in complex matrices like seawater, moderate inhibition of the sorption process was observed, attributed to a change in mercury speciation. The loadings achieved are similar to the majority of literature values found for other biosorbents and for other metals, suggesting that cork stoppers can be recycled as an effective biosorbent for water treatment. However, the most interesting result is that equilibrium data show a very rare behaviour, with the isotherm presenting an almost square convex shape to the concentration axis, with an infinite slope for an Hg concentration in solution around 25 μg/L.     

Air-surface exchange of mercury with soils amended with ash materials

Air-surface exchange of mercury (Hg) was measured from soil low in Hg (0.013 mg/kg) amended with four different ash materials: a wood ash containing -10% coal ash (0.070 mg/kg Hg), a mixture of two subbituminous coal fly ashes (0.075 mg/kg Hg), a subbituminous coal ash containing -10% petroleum coke ash (1.2 mg/kg Hg), and an ash from incinerated municipal sewage sludge (4.3 mg/kg Hg) using a dynamic flux chamber. Ash was added to soil to simulate agricultural supplements, soil stabilization, and pad layers used in livestock areas. For the agricultural amendment, -0.4% ash was well mixed into the soil. To make the stabilized soil that could be used for construction purposes, -20% ash was mixed into soil with water. The pad layer consisted of a wetted 1-cm layer of ash material on the soil surface. Diel trends of Hg flux were observed for all of the substrates with significantly higher Hg emissions during the day and negligible flux or deposition of Hg during the night. Hg fluxes, which were measured in the summer months, were best correlated with solar radiation, temperature, and air O3 concentrations. Mean Hg fluxes measured outdoors for unamended soils ranged from 19 to 140 ng/m2 day, whereas those for soil amended with ash to simulate an agricultural application ranged from 7.2 to 230 ng/m2 day. Fluxes for soil stabilized with ash ranged from 77 to 530 ng/m2 day and for soil with pads constructed of ash ranged from -50 to 90 ng/m2 day. Simple analytical tests (i.e., total Hg content, synthetic precipitation leaching procedure, heating, and indoor gas-exchange experiments) were performed to assess whether algorithms based on these tests could be used to predict Hg fluxes observed outdoors using the flux chamber. Based on this study, no consistent relationships could be developed. More work is needed to assess long-term and seasonal variations in Hg flux from (intact and disturbed) substrates before annual estimates of emissions can be developed.     

Ground discarded tires remove naphthalene, toluene, and mercury from water

Ground discarded tires adsorb naphthalene, toluene, and mercury ions (Hg2+) from aqueous solutions. Their sorption properties and kinetics were determined by batch equilibration techniques at 20 degrees C. The isotherms were linear for naphthalene and toluene and their sorption coefficients were about 1340 and 255 (ml/g), respectively. Sorption of the organic compounds by the ground rubber particles was relatively fast (within 30 min). However, the mercury isotherms were non-linear, and its sorption was slow as compared to the sorption of the organics. The rubber particles had a strong affinity for Hg2+. These results show that ground discarded tires are effective in removing organic compounds and Hg2+ from wastewater and other contaminated environments. In addition it would be a useful, environmentally friendly use of discarded tires (one tire per year per capita is discarded in the United States).     

Distribution of total mercury, methyl mercury and selenium in pod of killer whales (Orcinus Orca) stranded in the northern area of Japan: comparison of mature females with calves

Total mercury (T-Hg) and selenium (Se) concentrations in liver, kidney and muscle from a pod of killer whales including five mature females and three calves stranded in the northern area of Japan were analyzed. In the mature female, contamination level of T-Hg in the liver sample (62.2+/-21.9 microg/wet g) was markedly higher than that in kidney sample and muscle sample. The molar ratio of T-Hg to Se in the liver sample was approximately 1, and those in the kidney and muscle samples were markedly lower than 1. These results suggest that the formation of HgSe compound increases the hepatic accumulation of mercury (Hg). In contrast, contamination level of T-Hg in the calf organs was much lower than that in the mature female organs. These results suggest that the transfer of Hg from the mother to the fetus via placenta and/or to calf via milk is trace.     

The role of ammonia on mercury leaching from coal fly ash

The Federal Clean Air Interstate Rule issued in March 2005 will result in many power plants employing ammonia-based technologies to control NO(x) emission. The Clean Air Mercury Rule, issued at the same time, will encourage many power plants to use various technologies to remove mercury from flue gas, generating fly ashes that contain elevated concentrations of mercury. Ammonia forms relatively strong complexes with mercury compared to most other cationic elements and, therefore, may change the leaching characteristics of mercury. Understanding the impact of ammonia on the leaching of mercury from fly ash is critical in predicting the potential environmental impact of future fly ash. Batch methods were used to investigate the ammonia impact on mercury leaching from fly ash under different pH conditions. The results indicated that mercury leaching without external ammonia addition is not significant. However, ammonia addition increased mercury leaching in the alkaline pH range, due to the formation of less adsorbable mercury-ammonia complexes. Washed ash released more mercury than the raw ash if the ammonia concentration is the same, mainly due to the dissolution of some ash components during washing which exposed more mercury on ash surface. Mercury adsorption data indicated that more than 90% of available mercury was adsorbed by fly ash even in the presence of 1000 mg l(-1) ammonia addition.