Kinetic and mechanism studies of the adsorption of lead onto waste cow bone powder (WCBP) surfaces

This study examines the adsorption isotherms, kinetics and mechanisms of Pb²⁺ sorption onto waste cow bone powder (WCBP) surfaces. The concentrations of Pb²⁺ in the study range from 10 to 90 mg/L. Although the sorption data follow the Langmuir and Freundlich isotherm, a detailed examination reveals that surface sorption or complexation and co-precipitation are the most important mechanisms, along with possibly ion exchange and solid diffusion also contributing to the overall sorption process. The co-precipitation of Pb²⁺ with the calcium hydroxyapatite (Ca-HAP) is implied by significant changes in Ca²⁺ and PO₄ ^3? concentrations during the metal sorption processes. The Pb²⁺ sorption onto the WCBP surface by metal complexation with surface functional groups such as ≡ POH. The major metal surface species are likely to be ≡ POPb⁺. The sorption isotherm results indicated that Pb²⁺ sorption onto the Langmuir and Freundlich constant q _max and K _F is 9.52 and 8.18 mg g^?1, respectively. Sorption kinetics results indicated that Pb²⁺ sorption onto WCBP was pseudo-second-order rate constants K ₂ was 1.12 g mg^?1 h^?1. The main mechanism is adsorption or surface complexation (≡POPb⁺: 61.6%), co-precipitation or ion exchange [Ca_3.93 Pb_1.07 (PO₄)₃ (OH): 21.4%] and other precipitation [Pb 50 mg L^?1 and natural pH: 17%). Sorption isotherms showed that WCBP has a much higher Pb²⁺ removal rate in an aqueous solution; the greater capability of WCBP to remove aqueous Pb²⁺ indicates its potential as another promising way to remediate Pb²⁺-contaminated media.     

Kinetic,equilibrium and thermodynamic studies for the sorption of metribuzin from aqueous solution using banana peels,an agro-based biomass

Banana peels were employed for the removal of metribuzin from aqueous solution. Sorption in the batch mode was optimized regarding pH, contact time, sorbent dose, initial pesticide concentrations, and temperature. The sorption data were fitted to pseudo-first-order, pseudo-second-order, intraparticle diffusion, Elovich, and liquid film diffusion model, the pseudo-second-order exhibiting best fit (R² = 0.9803). Of the four most common sorption isotherm models (Langmuir, Freundlich, Tempkin, and Dubinin–Radushkevich), the data followed the Langmuir isotherm with highest correlation. The maximum adsorption capacity was found to be 167 mg g^?1. Gibbs free energy, enthalpy, and entropy showed that the sorption was exothermic and spontaneous.     

Removal of heavy metals from aqueous solutions using activated carbon prepared from Cicer arietinum

Removal of Cu²⁺, Cd²⁺, Pb²⁺, and Zn²⁺ from aqueous solutions by activated carbon prepared from stems and seed hulls of Cicer arietinum, an agricultural solid waste, has been studied. The influence of various parameters, such as pH, contact time, adsorbent dose, and initial concentration of metal ions on removal was evaluated. The activated carbon was characterized by FT-IR spectroscopy, X-ray diffraction, and elemental analysis. Sorption isotherms were studied using Langmuir and Freundlich isotherm models. All experimental sorption data were fitted to the sorption models using nonlinear least-squares regression. The maximum adsorption capacity values for activated carbon prepared from Cicer arietinum waste for metal ions were 18 mg g^?1 (Cu²⁺), 18 mg g^?1 (Cd²⁺), 20 mg g^?1 (Pb²⁺), and 20 mg g^?1 (Zn²⁺), respectively. The Freundlich isotherm model fit was best, followed by the pseudo-second-order kinetic model. Desorption studies were carried out with dilute hydrochloric acid for quantitative recovery of the metal ions and for regeneration of the adsorbent.     

Magnetic particles precipitated onto wheat husk for removal of methyl blue from aqueous solution

Magnetic particles prepared via co-precipitation and impregnated onto wheat husk (MN-WH) were used for the removal of methyl blue (MB) from aqueous solution. Experiments were conducted in a batch mode for optimization regarding pH, contact time, adsorbent dose, initial dye concentrations, and temperature. Maximum adsorption (98%) was achieved at pH 5. The adsorption data were fitted into pseudo-first, pseudo-second, intraparticle diffusion, and Elovich equation revealing that adsorption followed pseudo-second-order kinetics. The four most common isotherm models, i.e. the Langmuir, Freundlich, Tempkin, and Dubinin–Radushkevich (D–R), were used to evaluate the data, with the best fit to a Langmuir isotherm (R² = 0.996), followed by a Freundlich isotherm (R² = 0.995), indicating monolayer adsorption of MB on the surface of MN-WH. Thermodynamic parameters calculated from the Van't Hoff equation revealed that the adsorption is exothermic (ΔHº = ?19.7 kJ mol^?1).     

The effects of soil properties and temperature on the adsorption isotherms of lead on some temperate and semiarid surface soils of Iran

Sorption of metal ions by soil and clay minerals is a complex process involving different mechanisms, and controlled by different variables that can interact. The aim of this work was to study the retention mechanisms of Pb ions on different soil samples. Surface soils were sampled from Guilan and Hamadan provinces in north and northwest of Iran with temperate and semiarid climates. The adsorption isotherms of Pb on the soils have been studied at 15, 27 and 37°C. The adsorption data for different soils were fitted into Langmuir and Freundlich models. Temperate soil samples had higher clay content, cation exchange capacity, dichromate (oxidable) organic carbon, total Kjeldahl-nitrogen, biological activity, amorphous and crystalline Fe and Al, but semiarid soil samples had higher sand content, pH, equivalent calcium carbonate, available P and K. Lead adsorption data obtained from semiarid soils against those obtained from temperate soils were better fitted in both Langmuir and Freundlich models. Langmuir constants Q ₀ for Pb adsorption in semiarid soils were considerably lower than those for Pb adsorption in temperate soils. However, the binding energy (K _L) of Pb and Freundlich constant n were higher for data of semiarid soils. The effect of temperature on the Pb adsorption was positive especially in temperate soils; however, soil properties had higher effects on Pb adsorption.     

Heavy metals uptake from aqueous solutions using marine algae (Colpomenia sinuosa): kinetics and isotherms

The adsorption of copper, zinc, cobalt, lead and cadmium ions onto Colpomenia sinuosa was studied as a function of contact time, initial metal ion concentration and initial pH. In addition, desorption studies were performed. Characterisation of this adsorbent was also confirmed by Fourier transform infrared (FTIR) spectroscopy and scanning electron microscopy (SEM) analysis. Batch adsorption experimental data were analysed using Langmuir, Freundlich and Dubinin–Raduschkevich (D–R) adsorption isotherms. The results indicated that the biosorption equilibrium was well described by both the Freudlich and D–R isotherms. Moreover, sorption kinetics was performed and it was observed that equilibrium was reached in<60 min, which could be described by the pseudo-second-order kinetic model for all heavy metals. The sorption of heavy metals onto the biomass was largely dependent on the initial solution pH. The elution efficiency for heavy metal ions desorption from C. sinuosa was determined for 0.1 M HCl, 1.0 M HCl and 1.0 M HNO₃. Desorption efficiency and also adsorption capacity were highest for Pb(II). The results indicate that C. sinuosa has great potential for the removal of heavy metals in an ecofriendly process.     

富磷污泥生物炭去除水中Pb(Ⅱ)的特性研究

以城市污水厂富磷剩余污泥为研究对象,考察高温热解制备生物炭吸附剂对水中Pb(Ⅱ)的去除效果.研究表明,随着热解温度升高,制备的生物炭对Pb(Ⅱ)的吸附能力增强;在相同热解温度下,生污泥生物炭对Pb(Ⅱ)的吸附能力比消化污泥生物炭大.采用700℃热解1 h制备生污泥生物炭以研究对Pb(Ⅱ)吸附的影响因素,结果显示:吸附180 min达到吸附平衡;富磷污泥生物炭对Pb(Ⅱ)的去除率随pH增加而升高;生物炭投加量增加,对Pb(Ⅱ)去除率上升,而单位吸附容量迅速减小.污泥生物炭对Pb(Ⅱ)的吸附符合准二级反应动力学,Langmuir模型比Freundlich模型能更好地拟合等温吸附线.在pH 5.0、吸附时间3 h、生物炭投加量20 g.L-1条件下,对Pb(Ⅱ)的最大吸附量为34.5 mg.g-1,表明富磷污泥生物炭可以作为一种廉价的吸附剂.     

Adsorption of cationic and anionic surfactants onto organic polymer resin Lewatit VPOC 1064 MD PH

The adsorption of a cationic (CTAB, cetyl trimethylammonium bromide) and an anionic surfactant (SLES, sodium dodecylethersulfate) from aqueous solution onto organic polymer resin (Lewatit VPOC 1064 MD PH) was studied. A series of batch experiments were performed to determine the sorption isotherms of surfactants to organic polymer resin. The experimental studies were analyzed by Langmuir and Freundlich isotherms. Furthermore, the isotherm parameters, average percentage errors (ε) of model data, and separation factor (R _L) were calculated. Other factors influencing the adsorption capacity (contact time, adsorbent amount, and initial surfactant concentration) were also discussed. The experimental data fitted very well to the Langmuir equilibrium model in the studied concentration range. The calculated R _L values showed that the adsorption of both surfactants were favorable. Among the surfactants, CTAB showed higher adsorption capacity onto organic polymer resin compared to SLES (Q ⁰ = 250 and 34.36 mg g⁻¹, respectively).     

全氟化合物在阳离子表面活性剂改性碳纳米管上的吸附

采用两种阳离子表面活性剂,四丁基溴化铵(TBA)及聚乙烯亚胺(PEI)对碳纳米管进行改性,并研究了全氟辛酸(PFOA)、全氟辛烷磺酸盐(PFOS)、全氟己烷磺酸盐(PFHxS)在改性碳纳米管上的吸附行为.研究结果显示,除PFOS在TBA修饰的碳纳米管(TBA-MWCNTs)上的吸附等温线呈线性外,全氟化合物在原碳纳米管(Pri-MWCNTs)、TBA-MWCNTs及PEI修饰的碳纳米管(PEI-MWCNTs)上的吸附均为非线性.吸附等温线可以用Freundlich及Langmuir模型拟合.与Pri-MWCNTs相比,PEI-MWCNTs的零电荷点(pHzpc)增加了6.2个单位,全氟化合物的吸附系数Kd值增加2—3倍;而TBA-MWCNTs的pHzpc增加了1.0个单位,PFOS在高平衡浓度下的Kd值增加了两倍.随着溶液pH值的降低,全氟化合物在Pri-MWCNTs和PEI-MWCNTs上的吸附量有所增加,而在TBA-MWCNTs上的吸附受pH值的影响不大.这说明疏水作用及静电作用是全氟化合物在Pri-MWCNTs和PEI-MWCNTs上吸附的主要机制,而疏水作用则为TBA-MWCNTs上吸附的主要机制.与单溶质体系相比,PFOS与PFOA同时存在时二者在PEI-MWCNTs上吸附的Kd值均有所减小,且PFOA的减小程度大于PFOS.PFOS在TBA-MWCNTs上吸附的Kd值在高浓度下几乎不受PFOA的影响.     

Competitive adsorption and desorption of copper and lead in some soil of North China

The competitive adsorption and desorption of Pb(II) and Cu(II) ions in the soil of three sites in North China were investigated using single and binary metal solutions with 0.01 mol·L^-1 CaCl₂ as background electrolyte. The desorption isotherms of Pb(II) and Cu(II) were similar to the adsorption isotherms, which can be fitted well by Freundlich equation (R₂>0.96). The soil in the three sites had greater sorption capacities for Pb(II) than Cu(II), which was affected strongly by the soil characteristics. In the binary metal solution containing 1∶1 molar ratio of Pb(II) and Cu(II), the total amount of Pb(II) and Cu(II) adsorption was affected by the simultaneous presence of the two metal ions, indicating the existence of adsorption competition between the two metal ions. Fourier transform infrared (FT-IR) spectroscopy was used to investigate the interaction between soil and metal ions, and the results revealed that the carboxyl and hydroxyl groups in the soil were the main binding sites of metal ions.     

花生壳吸附Pb^2＋、Cu^2＋、Cr^3＋、Cd^2＋、Ni^2＋的动力学和热力学研究

以花生壳为生物吸附剂,通过序批式实验研究了吸附剂投量、吸附时间、金属离子初始质量浓度、吸附温度对吸附金属离子的影响,探讨了花生壳吸附的动力学及热力学特性。结果表明,准二级动力学方程能很好地描述花生壳对Pb^2＋、Cu^2＋、Cr^3＋、Cd^2＋、Ni^2＋的吸附过程。Langmuir模型和Freundlich模型均能较好地描述花生壳对5种重金属离子的等温吸附过程,而Langmuir模型拟合的线性更好。Pb2＋、Cu2＋、Cr3＋、Cd2＋、Ni2＋5种金属离子的最大吸附量分别是32.25、7.09、3.82、2.95、2.22 mg.g-1,花生壳可用于处理低质量浓度多种重金属混合的废水。热力学研究表明,花生壳对5种金属离子的吸附具有自发、吸热和熵增的特性。     

添加羟基磷灰石对土壤铅吸附与解吸特性的影响

采用羟基磷灰石对四种不同类型的土壤进行铅的吸附-解吸试验.结果表明:四种土壤对铅的吸附均可用Langmuir和Freundlich方程进行描述,土壤中加入羟基磷灰石明显增加了土壤对铅的吸附量和吸附亲和力,同时降低了土壤中铅的解吸百分数,在偏酸性的红壤上表现更为明显,其最大吸附量增加28%.羟基磷灰石对铅吸附的反应机理可能与磷灰石溶解后与铅形成磷酸盐沉淀及其对铅的表面吸附作用有关.土壤对铅的吸附量及吸附亲和力与土壤的有机质、阳离子交换量及粘粒含量有显著正相关,而与土壤砂粒的含量呈负相关.     

Modelling the kinetics and equilibrium properties of cadmium biosorption by river green alga and water hyacinth weed

Cadmium biosorption properties of non-living, dried river green alga from a river source, and water hyacinth weed, Eichhornia crassipes from a lake in Zimbabwe have been investigated. The cadmium uptake was found to depend on initial pH, uptake being apparently minimal at low pH values and increasing with an increase in pH. Cadmium biosorption kinetics by both samples is fast, with 80% of total uptake occurring within 60?min. The effect of initial solution pH and initial cadmium concentration on cadmium biosorption from a cadmium solution has been studied. The data for algal biomass fitted the Langmuir monolayer adsorption isotherm, while the biosorption of the metal by water hyacinth weed fitted the Freundlich adsorption isotherm with 1/n values all less than 1. Maximum metal uptake capacities were recorded using 0.35?g of biomass and a 250?mg?L^?1 cadmium solution at pH 6.5 and at 25°C and these were about 85 and 50?mg?L^?1 for water hyacinth weed and green alga, respectively, showing that water hyacinth weed offered a greater potential for cadmium uptake. The absorption was described by pseudo-second order rate model and the rate constant and equilibrium sorption capacity are reported.     

重金属-柠檬酸-针铁矿三元体系的表面络合模型研究

根际环境产生的柠檬酸等小分子有机酸可能影响重金属的溶出效应.本文研究了 4种重金属Cd、Pb、Cu、Ni及柠檬酸在针铁矿表面的三元体系吸附行为,结果发现柠檬酸促进了 4种重金属酸性条件下在针铁矿表面的吸附量,而Cu、Ni促进了柠檬酸碱性条件下的吸附.结合红外光谱图发现,重金属-柠檬酸-针铁矿主要存在以下2种三元体系形态...     

海泡石黏土矿物对Cu2+的吸附动力学研究

研究分析了海泡石黏土矿物对铜离子的吸附性能和动力学特征,结果表明,海泡石黏土矿物对Cu~(2 )吸附的最佳pH值为6.0左右,随着pH值的增大,吸附作用减弱;在[Cu~(2 )]=100mg·l~(-1),溶液pH值为6,吸附时间为2h时,添加0.1 g海泡石,海泡石对Cu~(2 )的吸附去除率仅为39.5%,当海泡石用量提高至0.4 g时,其对Cu~(2 )的吸附去除率提高到94.8%;实验结果同样显示,18min内有90%的Cu~(2 )被海泡石吸附,随着吸附时间的增加,吸附作用趋于稳定,2h可达到吸附平衡。该吸附过程符合Langmuir和Freundlich等温吸附方程.同时,分别采用拟一级模型和拟二级模型考察了吸附动力学,并计算了这些动力学模型的速率常数.实验数据和拟二级模型计算结果之间有较好的相关性.     

Lead(II) and cadmium(II) removal from aqueous solution using processed walnut shell: kinetic and equilibrium study

The biosorption potential of processed walnut shell for Pb(II) and Cd(II) ions from aqueous solutions was explored. The effects of pH, contact time, initial ion concentration, and amount of dried adsorbent were studied in batch experiments. The maximum adsorption was achieved within the pH range 4.0–6.0. The equilibrium data were well fitted by the Langmuir isotherm model. The maximum monolayer adsorption capacities were found to be 32?g?kg^?1 and 11.6?g?kg^?1 for Pb(II) and Cd(II) ions, respectively. Kinetic data were best described by the pseudo-second-order model. The structural features of the adsorbent were characterized by Fourier transform infrared spectroscopy, which confirmed the involvement of hydroxyl (–OH), carboxyl (–COO^–), and carbonyl (C=O) groups in metal sorption. This readily available adsorbent is efficient in the uptake of Pb(II) and Cd(II) ions from an aqueous solution and could be used for the treatment of wastewater streams bearing these metal ions.     

Metal removal with two biochars made from municipal organic waste: adsorptive characterization and surface complexation modeling

The adsorptive characteristics of biochar produced from garden green waste (S-char) and a mixture of food waste and garden green waste (FS-char) were investigated. Adsorption of Cu²⁺, Zn²⁺, and Mn²⁺ onto the two biochars reached equilibrium within 48 hours. The metal adsorption was effectively described by the pseudo-second-order kinetic and Freundlich isotherm models which suggest heterogeneous chemisorption. The initial solution pH influenced adsorption of Zn²⁺ and Mn²⁺ but not of Cu²⁺. Simulation via a surface complexation model showed that the fraction of XOCu⁺ adsorbed onto biochar was increased with increasing pH until it reached the adsorption maximum at pH 8.5, while the endpoint for the maximum of XOMn⁺ was higher than pH 12.     

黄河水体沉积物对敌百虫和甲拌磷的吸附

对敌百虫和甲拌磷在黄河水体沉积物中的吸附特性进行了研究,观察了ｐＨ值和离子强度等因素对吸附的影响．结果表明,敌百虫的吸附过程为一级动力学规律;敌百虫的吸附符合Ｌａｎｇｍｕｉｒ等温式,甲拌磷的吸附可用Ｆｒｅｕｎｄｉｃｈ等温式较好地描述．ｐｈ值降低或离子强度增加使敌百虫和甲拌磷在沉积物中的吸附程度明显减小．敌百虫在黄河水体沉积物中的吸附以表面吸附为主,而甲拌磷则表现为表面吸附和在有机碳中的分配作用两种吸附方式．     

Trichoderma harzianum: a green sorbent for Pb(II) uptake from aqueous solutions

This investigation describes the use of specially cultivated, nonliving biomass of Trichoderma harzianum as a biosorbent for the batch removal of Pb(II) from a stirred system under different experimental conditions. The metal removal depended upon pH, sorbent particle size, initial Pb(II) concentration, shaking speed, and sorption time. The optimal experimental conditions for the removal of Pb(II) by T. harzianum with an initial metal concentration of 100 mg L^?1 were obtained at a particle size of 53 μm, a pH of 4.5, a shaking speed of 200 rpm, and a contact time of 720 min. The results were analyzed in terms of adsorption isotherms and kinetic models. The Freundlich isotherm model and pseudo second-order model fitted well in the data. T. harzianum proved to be a good biomaterial for accumulating Pb(II) from aqueous solutions (q = 460 mg g^?1).     

Removal of chromium(VI) by ZnCl2 activated coir pith carbon

The adsorption of chromium(VI) onto ZnCl₂ activated carbon developed from coir pith was investigated to assess the possible use of this adsorbent. The influence of contact time, adsorbent dose, Cr(VI) concentration, pH and temperature were investigated. The two theoretical adsorption isotherms, namely, Langmuir and Freundlich were used to describe the experimental results. The Langmuir adsorption capacity (Q ₀) was found to be 120.5?mg Cr(VI) per g of the adsorbent. The adsorption followed the second-order kinetics and was found to be maximum at pH 2.0. The pH effect and the desorption studies showed that ion exchange mechanism might be involved in the adsorption process. The effects of foreign ions such as chloride, sulphate, phosphate, selenite, molybdate, nitrate and perchlorate on the removal of Cr(VI) have been investigated. The removal of Cr(VI) from synthetic ground water was also tested. The results show that ZnCl₂ activated coir pith carbon is effective for the removal of Cr(VI) from water.