共查询到19条相似文献,搜索用时 328 毫秒
1.
2.
此文对T10钢经线切割加工的开裂模具进行了金相分析、应力分析和断裂分析,从而提出了减少变形和开裂的措施。列举了生产实例,供模具制造者参考。 相似文献
3.
此文针对模具线切割过程中产生开裂和变形的现象,从残余应力的产生原因、影响模具线切割开裂和变形的因素较全面的进行了分析和论述,模具线切割开裂和变形是由于其模板内部的残余应力,尤其是热处理残余应力所致,但线切割在一定程度上破坏了模板内残余应力平衡状态,诱发了开裂或变形。根据影响的诸因素,提出了预防开裂和变形的各种措施,但措施的有效性还须因件施策,满足模具的使用寿命和顾及对后序加工的影响。 相似文献
4.
5.
端头多半圆弯曲件比较常见,但质量难以保证。此文通过对成形弯曲工艺的分析,提出了改进措施,并介绍了两种典型模具结构,及其零部件的设计。 相似文献
6.
针对具体工件对相对弯曲半径R0/t=160左右弯曲件的回弹进行了试验研究。分析了有关回弹(R0/t≥10)计算和图表对相对弯曲半径很大时的适用程度,并与生产过程中的实测值进行了比较。 相似文献
7.
分析了挤压制件内部金属的应变及其分布特征。将挤压成形与剪切加工作了比较。根据挤压变形的特征得出了“附加拉应力和挤压件内部的强烈剪切变形是导致挤压件出现45度开裂和表面环裂的根本原因”的结论。提出利用挤压变形特性进行精密冲裁的设想。 相似文献
8.
推导了斜刃倾角取不同数值时,剪切力的计算公式,分析和探讨了在斜刃剪切时,斜刃倾角的大小对剪切力及冲裁件的加工质量的影响。在实际生产中,对于合理选择斜刃倾角的大小,正确地计算剪切力具有重要的指导意义。 相似文献
9.
对U型截面弯曲件失稳起皱问题进行了研究,通过板材成形性能实验及起皱模拟实验,对失稳起皱原因进行了分析,为类似的异型截面弯曲件起皱的预防提供了可行的实验分析方法。 相似文献
10.
实际工作中 ,常常会发现有的弯曲件经模具弯曲后的实际尺寸与预先计算的展开料尺寸有较大偏差。针对这一问题 ,从中性层弯曲半径的计算公式及中性层的位移、几种弯曲工艺方案的比较和不同弯曲模具结构的选择等方面 ,分析了造成这种偏差、影响弯曲件展开料尺寸计算准确性的几个因素 相似文献
11.
《Journal of Manufacturing Processes》2014,16(4):494-502
A new mass finishing technology, namely drag finishing of brass (Cu–30 wt.% Zn) rings with fluidized abrasives, is reported. A new equipment, which combines the typical features of the drag finishing machines to hold the workpiece with the moving abrasives of fluidized beds, was designed. The equipment was validated by performing several experimental tests varying rotary speed and processing time. The evolution of the surface morphology of the workpieces, their mass loss and dimensional accuracy after processing were assessed after each finishing step. The designed equipments allowed to finish with a high level of accuracy and in short time range the brass rings. Material removals and out-of-tolerances of the workpieces could be limited once the appropriate settings of the process were selected. Low energy requirements, lack of any residuals after processing and facile operations make the fluidized bed assisted drag finishing industrially sustainable and very promising in several manufacturing domains. 相似文献
12.
13.
弯曲线不重合且其精度要求较高的V形件的弯曲,是一较为棘手的问题。本文介绍了一种利用顶板侧壁的斜面,迫使下模框内摆块转动,从而克服工件回弹,并确保弯曲精度的V形弯曲模的设计。 相似文献
14.
目的为获得合适的裂解力,以某款轿车发动机连杆为研究对象,应用扩展有限元法(Extended Finite Element Method,XFEM)对裂解工艺中的裂解力进行计算分析。方法根据部件的实际尺寸建立预制初始微裂纹条件下的连杆裂解有限元模型,确定相关的材料参数,并进行有限元网格划分,确定部件之间的约束类型。以应力强度因子大于材料断裂韧度,裂纹即扩展为依据,反复试算得出应力强度因子达到断裂韧度时的裂解力,进而通过大量计算和数据拟合得出初始微裂纹长度与裂解力之间的关系。分析裂解力对塑性区的影响,为裂解力阈值确定给出参考。结果当裂解力能够满足裂解工艺要求时,预制的初始微裂纹长度应尽可能小。结论最为理想的裂解力为材料断裂韧度对应的裂解力。文中提出的分析方法也适合于求解各类连杆的裂解力。 相似文献
15.
16.
17.
目的 改善块体非晶合金的弯曲力学性能,同时考虑航空结构材料选材的经济性,研究激光表面处理工艺对工业级Zr49.7Ti2Cu37.8Al10Er0.5块体非晶合金弯曲变形和缺口韧性的影响规律。方法 采用低纯原料和低真空制备条件获得工业级Zr49.7Ti2Cu37.8Al10Er0.5块体非晶合金试样,考虑到弯曲条件下试样受到拉伸和压缩2种正应力状态,研究不同处理工艺和激光处理表面对试样弯曲变形和缺口韧性的影响。结果 当激光处理表面位于弯曲试样的2个侧表面时,其对试样的塑性变形能力和断裂强度没有明显的影响,但会显著降低试样的缺口韧性,从(56.4±3.4)MPa·m1/2降低到(26.2±4.8)MPa·m1/2;激光处理表面位于弯曲试样的受拉侧时,试样的弯曲断裂强度从2 150 MPa降低到1 800 MPa;当激光处理表面位于... 相似文献
18.
Takashi Matsumura Hitoshi Sadakata Hiroshi Makihata Masahiko Yoshino 《Journal of Manufacturing Processes》2013,15(1):8-13
A micro fabrication is presented to control wettability on cylinder surfaces. A machine tool is developed to form the micro-scale structure on the cylinder in incremental stamping. The stamping tool is manufactured with fabricating the micro-scale structure on the top of the tool in FIB sputtering. The micro incremental stamping is repeated with linear motion of the tool and rotation of the workpiece. The rotation is controlled by the friction drive on the machine table because of the stable stamping with reducing bending of the workpiece. The critical stamping depth, the minimum depth in which the structure is formed, is determined in the forming tests using the structured tool. Then, a stripe type structure is formed to control wettability on the cylinder surface. Anisotropic wettability appears on the structured surface. 相似文献