SAMPLING FRAME FOR IMPROVING PEBBLE COUNT ACCURACY IN COARSE GRAVEL‐BED STREAMS1

ABSTRACT: Improved sampling techniques are needed to increase the accuracy of pebble‐count particle‐size distributions used for stream studies in gravel‐bed streams. However, pebble counts are prone to operator errors introduced through subjective particle selection, serial correlation, and inaccurate particle‐size measurements. Errors in particle‐size measurements can be minimized by using a gravel template. Operator influence on particle selection can be minimized by using a sampling frame, 60 by 60 cm, in which sampling points are identified by the cross points of thin elastic bands. Serial correlation can be minimized by adjusting the spacing between the cross points and setting it equal to the dominant large particle size (=D₉₅). In a field test in a cobble‐bed stream, the sampling frame developed in this study produced slightly coarser size distributions, particularly in the cobble range, than the traditional heel‐to‐toe walk that selects particles with a blind touch at the tip of the boot. The sampling frame produced more similar sampling results between two operators than heel‐to‐toe walks. The difference between the two sampling methods is attributed to an unbiased selection of fine and coarse particles when using the sampling frame.     

TGA analysis of tobacco rob pyrolysis and release characteristics of noncondensable gas in a fixed-bed reactor

In this study, the size of tobacco rob (TR) particle was considered as a major factor in determining the mass loss in thermogravimetric analysis (TGA) and product yield and composition at different reactor temperatures in the fixed-bed reactor. The TGA results showed that the conversion rate increased and the activation energy (ranged from 53.29 to 58.25 kJ/mol) decreased with a decrease in particle size. The experiments demonstrated that fuel gas yield (from 0.76 to 0.82 Nm³/kg at 900 °C) increased with a decrease in particle size while char and tar yield decreased. Smaller particle sizes resulted in higher H₂ (25.68%) and CO (27.36%) contents. Minimizing the size of raw materials is an alternative method to improve the gas quality of TR pyrolysis. The increase of gas yield was attributed to the decomposition of char and tar vapor as temperature increased.     

Measuring runoff-suspended solids using an improved turbidometer method

Differences in particle size distribution between runoff standards and unknown samples affect the accuracy of estimation of total suspended solids (TSS) concentration using the nephelometric turbidity (NTU) method. The objective was to quantify the effects of a sucrose solution as suspending medium and contrasting particle size distribution on nephelometric turbidity and accuracy of TSS estimation. Nineteen benchmark soils varying in texture and color were divided into particle size distribution of <250 and <2000 microm. Soils from these two aggregate classes were then made into suspension ranging from 0.2 to 15 g L-1 using distilled deionized water. Runoff suspensions ranging from 0.2 to 21 g L-1 were also collected from different watersheds. Turbidity of soil and runoff suspensions was measured in sucrose solution and in distilled deionized water. The sucrose solution density ranged from 1.10 to 1.30 kg L-1. Increasing sucrose solution density decreased turbidity. The TSS concentration was most sensitive to changes in turbidity with the 1.30 kg L-1 sucrose solution. Using the 1.30 kg L-1 sucrose solution, particle size bias and error of TSS estimates were decreased by at least 20% compared to distilled deionized water. Reduction in refraction index differences between the suspended particles and sucrose solution combined with reduced particle settling and reduced Brownian motion resulted in dampening the effects of particle size distribution. We propose a sucrose solution of 1.30 kg L-1 as a better suspending medium to dampen the effect of particle size distribution and thus improve suspension TSS concentration estimation.     

Capture of carbon dioxide from flue or fuel gas mixtures by clathrate crystallization in a silica gel column

A column of silica gel was employed to contact water with flue gas (CO₂/N₂) mixture to assess if CO₂ can be separated by hydrate crystallization. Three different silica gels were used. One with a pore size of 30 nm (particle size 40–75 μm) and two with a pore size of 100 nm and particle sizes of 40–75 and 75–200 μm respectively. The observed trends indicate that larger pores and particle size increase the gas consumption, CO₂ recovery, separation factor and water conversion to hydrate. Thus, the gel (gel #3) with the larger particle size and larger pore size was chosen to carry out experiments with concentrated CO₂ mixtures and for experiments in the presence of tetrahydrofuran (THF), which itself is a hydrate forming substance. Addition of THF reduces the operating pressure in the crystallizer but it also reduces the gas uptake. Gel #3 was also used in experiments with a fuel gas (CO₂/H₂) mixture in order to recover CO₂ and H₂. It was found that the gel column performs as well as a stirred reactor in separating the gas components from both flue gas and fuel gas mixtures. However, the crystallization rate and hydrate yield are considerably enhanced in the former. Finally the need for stirring is eliminated with the gel column which is enormously beneficial economically.     

Analysis of Cell Concentration,Volume Concentration,and Colony Size of Microcystis Via Laser Particle Analyzer

The analysis of the cell concentration, volume concentration, and colony size of Microcystis is widely used to provide early warnings of the occurrence of blooms and to facilitate the development of predictive tools to mitigate their impact. This study developed a new approach for the analysis of the cell concentration, volume concentration, and colony size of Microcystis by applying a laser particle analyzer. Four types of Microcystis samples (55 samples in total) were analyzed by a laser particle analyzer and a microscope. By the application of the laser particle analyzer (1) when n = 1.40 and k = 0.1 (n is the intrinsic refractive index, whereas k is absorption of light by the particle), the results of the laser particle analyzer showed good agreement with the microscopic results for the obscuration indicator, volume concentration, and size distribution of Microcystis; (2) the Microcystis cell concentration can be calculated based on its linear relationship with obscuration; and (3) the volume concentration and size distribution of Microcystis particles (including single cells and colonies) can be obtained. The analytical processes involved in this new approach are simpler and faster compared to that by microscopic counting method. From the results, it was identified that the relationship between cell concentration and volume concentration depended on the colony size of Microcystis because the intercellular space was high when the colony size was high. Calculation of cell concentration and volume concentration may occur when the colony size information is sufficient.     

Stabilization of composted organic matter after application to a humus-free sandy mining soil

The use of mining substrates for recultivation purposes is limited due to their low organic matter (OM) contents. In a 1-yr laboratory experiment we evaluated the stabilization of biowaste compost added to a humus-free sandy mining soil to examine the suitability of compost amendment for the formation of stable soil organic matter (SOM). The stabilization process was characterized by measuring enrichment of OM and nitrogen in particle size fractions obtained after dispersion with different amounts of energy (ultrasonication and shaking in water), carbon mineralization, and amount of dissolved organic carbon (DOC). During the experiment, 17.1% of the organic carbon (OC) was mineralized. Organic carbon enrichment in the < 20-micron particle size fraction at the beginning of the experiment was in the range of natural soils with similar texture. Within 12 mo, a distinct OC redistribution from coarse into fine fractions was found with both dispersion methods. The accumulation of OC was more pronounced for the size separates obtained by ultrasonication, where the carbon distribution between 0.45- to 20-micron particle size fractions increased from 30% at the beginning to 71% at the end of the experiment. Dissolved organic carbon contents ranged between 50 and 68 g kg-1 OC and decreased during the incubation. In conclusion, the exponential decrease of carbon mineralization and the OC enrichment in the fine particle size fractions both indicated a distinct OM stabilization in the mining soil.     

Physical, chemical, and mineralogical characteristics of a reservoir sediment delta (Lake Powell, U.S.A.) and implications for water quality during low water level

Lake Powell is a large reservoir in Utah and Arizona that has experienced large changes in water level during a recent drought. As a first step in assessing the connection between hydrologic and chemical changes at Lake Powell, we characterized the particle size and solid-phase bulk concentrations for 31 elements and 25 minerals in sediment from the inflow region and some shoreline locations by using laser diffractometry, X-ray fluorescence, elemental analysis, and X-ray diffraction Our results are consistent with previous results that show a negative correlation between particle size and concentrations of most elements and most minerals other than quartz and some feldspars. In our samples, however, solid-phase iron, rather than particle size or organic carbon, is the best predictor variable for the solid-phase concentrations of elements and minerals. Sediment characteristics vary on a scale of tens of kilometers, with fine sediment that is enriched in trace elementsnearer to the dam. These trends allow formulation of an algorithm for determining a water-level threshold below which sediment resuspension may alter water chemistry in a generic reservoir with a long and narrow sediment delta.     

Comparison of Three Pebble Count Protocols (EMAP,PIBO, and SFT) in Two Mountain Gravel‐Bed Streams1

Abstract: Although the term ``pebble count'' is in widespread use, there is no standardized methodology used for the field application of this procedure. Each pebble count analysis is the product of several methodological choices, any of which are capable of influencing the final result. Because there are virtually countless variations on pebble count protocols, the question of how their results differ when applied to the same study reach is becoming increasingly important. This study compared three pebble count protocols: the reach‐averaged Environmental Monitoring and Assessment Program (EMAP) protocol named after the EMAP developed by the Environmental Protection Agency, the habitat‐unit specific U.S. Forest Service’s PACFISH/INFISH Biological Opinion (PIBO) Effectiveness Monitoring Program protocol, and a data‐intensive method developed by the authors named Sampling Frame and Template (SFT). When applied to the same study reaches, particle‐size distributions varied among the three pebble count protocols because of differences in sample locations within a stream reach and along a transect, in particle selection, and particle‐size determination. The EMAP protocol yielded considerably finer, and the PIBO protocol considerably coarser distributions than the SFT protocol in the pool‐riffle study streams, suggesting that the data cannot be used interchangeably. Approximately half of the difference was due to sampling at different areas within the study reach (i.e., wetted width, riffles, and bankfull width) and at different locations within a transect. The other half was attributed to using different methods for particle selection from the bed, particle‐size determination, and the use of wide, nonstandard size classes. Most of the differences in sampling outcomes could be eliminated by using simple field tools, by collecting a larger sample size, and by systematically sampling the entire bankfull channel and all geomorphic units within the reach.     

Effects of nano-SiO(2) and different ash particle sizes on sludge ash-cement mortar

The effects of nano-SiO₂ on three ash particle sizes in mortar were studied by replacing a portion of the cement with incinerated sewage sludge ash. Results indicate that the amount of water needed at standard consistency increased as more nano-SiO₂ was added. Moreover, a reduction in setting time became noticeable for smaller ash particle sizes. The compressive strength of the ash–cement mortar increased as more nano-SiO₂ was added. Additionally, with 2% nano-SiO₂ added and a cure length of 7 days, the compressive strength of the ash–cement mortar with 1 μm ash particle size was about 1.5 times better that of 75 μm particle size. Further, nano-SiO₂ functioned to fill pores for ash–cement mortar with different ash particle sizes. However, the effects of this pore-filling varied with ash particle size. Higher amounts of nano-SiO₂ better influenced the ash–cement mortar with larger ash particle sizes.     

INFLUENCES OF INCREASED SAND DELIVERY ON THE MORPHOLOGY OF SAND AND GRAVEL CHANNELS1

ABSTRACT A flume study was conducted to examine (1)changes in the particle-size distribution of sediments in riffles due to the proportion of sand in transport and the total rate of bedload transport at the time the riffle is deposited and (2) the effect of high sand transport rates on the stability of gravel riffles. The median particle size of sediment deposited in the riffle was larger than that of the sediment in transport. Small but significant (a = 0.05) decreases in the median particle size of riffle sediments resulted as the sand-to-gravel ratio. Increased concentrations of sand in transport caused previously stable gravel riffles to undergo scour. These results, in combination with information from other studies, suggest that an alluvial channel with pool-riffle sequences and with sand and gravel beds may respond to an increased delivery of sand by reducing form roughness. Form roughness can be reduced by degrading riffles and filling pools. Subsequent responses may be increases in width-to-depth ratio and slope.     

Size distributions of fine and ultrafine particles in the city of Strasbourg: correlation between number of particles and concentrations of NO(x) and SO(2) gases and some soluble ions concentration determination

An Electrical Low Pressure Impactor (ELPI) was used during spring and autumn 2003 in the centre of Strasbourg for the measurement of atmospheric aerosols size distribution. The concentration of NO(x) and SO(2) in air was simultaneously measured with specific analysers. Samples were collected in the range 0.007-10 microm in equivalent aerodynamic diameter size. Number distributions are representative of a pollution originating from urban traffic with a particle size distribution exhibiting a nucleation mode below 29 nm and an accumulation mode around 80 nm in size. A mean particle density equal to 39000+/-35000 total particles per cm(3) with a size ranging from 7 to 10 microm was obtained after a sampling period of 2 weeks in spring. About 86.9% of the number of particles have an aerodynamic diameter below 0.1 microm and 13.1% between 0.1 and 1 microm. Correlation coefficients between the number of particles impacted on each ELPI plate and gas concentrations (SO(2) and NO(x)) showed that the numbers of particles with diameter between 0.10 and 0.62 microm are highly related to the NO(x) concentration. This result indicates that particles are traffic induced since NO(x) is mainly emitted by cars as shown by measurements on various sites. Particles are less clearly correlated to the SO(2) concentration. Particle analysis on different ELPI plates for a sampling period of 2 weeks in autumn showed high level of soluble NO(3)(-), SO(4)(2-) and NH(4)(+) ions. Indeed, up to 90% b.w. of these three species were found in the particle range 0.1-1 microm. The formation of particulate NH(4)NO(3) is favoured by high NO(x) concentration, which induces the formation of gaseous HNO(3).     

紫外分光光度测定总氮的影响因素探讨

本文介绍了测定总氮过程中,不同消解方法、碱性过硫酸钾的稳定时间、悬浮物粒径对总氮测定的影响。实验表明:碱性过硫酸钾避光在冰箱中至少可保存一个月,悬浮物粒径对总氮的测定无影响,消解总氮时,可在压力锅加热到120℃开始计时,恒温消解30分钟,自然冷却。     

Measurements,Theories and Simulations of Particle Deposits on Super-Heater Tubes in a CFB Biomass Boiler

The present investigation involves theories, simulations and experiments on deposit layers on super-heater tubes in a circulating fluidised bed in Västerås in Sweden. Simulation of particle trajectories in the vicinity of two super-heater tubes is conducted in a Eulerian-Lagrangian mode for the flue gas and the ash particles from the combustion process. Particle impingements on the tubes are investigated for different particle sizes. Measurements of the buildup of deposit layers in the super-heater environment are conducted using a deposit probe. Deposit layer growth and growth rate is analysed for different probe temperatures, as well as the aspect of sintering on the probe ring surface. Analysis of the probe deposit material and deposits from the super-heaters and from textile filters are chemically analysed. The temperature dependence of the deposit materials viscosity is predicted from the chemical analysis of the samples. A model is included to simulate the effect of the deposit layer thickness on the tube heat exchange. The results from the particle trajectory simulations show that particle larger than 10 mm will mainly impinge on the front of the first tube and that smaller particles are more dispersed due to turbulence and thermophorectic forces, enabling a more even impingement on the whole surface of the tubes. The probe deposit layer growth measurements show significant temperature dependence. The deposit material sintering and distribution is proven to be dependent on; temperature, particle size and exposure time. The stickiness of the deposit material is shown to be dependent on the SiO₂ and alkali relation in the samples, estimated through a viscosity model.     

Distribution of lead in relation to size of airborne particulate matter in Islamabad, Pakistan

Airborne particulate matter (PM) collected from two sampling stations in Islamabad, Pakistan, was analyzed for lead content and size gradation. A high volume air sampler was used to trap particulates on glass fiber filters for 8-12 h on a daily basis. Lead was estimated using a nitric acid digestion based AAS method on 44 samples from station 1 and 61 samples from station 2. Particle size fractions were categorized as <2.5, 2.5-10, 10-100 and >100 microm. The correlation between lead concentration and particle size was investigated. The results from two stations indicated average airborne lead concentrations of 0.505 and 0.185 microg/m3. Enhanced levels of lead were measured at a maximum of 4.075 microg/m3 at station 1 and 4.000 microg/m3 at station 2. PM < 2.5 and PM > 100 were found to constitute the local atmosphere in comparable proportions. A comparison of the lead levels is made with the existing permissible levels of this element laid down by different international agencies.     

Air classification of blast furnace dust collected in a fabric filter for recycling to the sinter process

Totally dry cleaning has become a common technology for top gas cleaning in blast furnaces in recent years. A significant advantage of totally dry gas cleaning is that the dust collected is obtained as dry powder, thus simplifying the recycling of the dust in the sinter plant and avoiding aqueous emissions. The concentration of some heavy metals, especially zinc, in the collected dust is usually higher than the maximum tolerable concentration for recycling to the sinter process. Therefore, a process for separation of dust with a low level of contamination from the rest is necessary to make partial recycling possible. This is possible because the limited components are more volatile and accumulate in the finer dust fraction. In wet blast furnace top gas cleaning, hydrocyclones are well established for this separation. For the separation of dry powder from the dry dedusting process air classification can be used. Dust from the top gas of a blast furnace with a fabric filter for dry top gas cleaning was split into several size fractions using a laboratory air classifier. The concentration of Ca, Cd, Cl, Cu, Fe, K, Na, Pb and Zn was analysed for each particle class and the loss on ignition was determined. A strong dependence of the concentration on the particle size was found for the more volatile metals, whereas the Fe and Ca concentration and the loss on ignition were quite evenly distributed. With the calculated recovery–removal-functions the possible recycling rate can be estimated for a given removal rate for the limited components.     

Removal of phenol from aqueous solutions by adsorption

Experiments have been conducted to examine the liquid-phase adsorption of phenol from water by silica gel, HiSiv 3000, activated alumina, activated carbon, Filtrasorb-400, and HiSiv 1000. Experiments were carried out for the analysis of adsorption equilibrium capacities and kinetics. The adsorption isotherm model of the Langmuir-Freundlich type was the best to describe adsorption equilibrium data for phenol for the adsorbents studied. Results of kinetic experiments indicated that HiSiv 1000 had the highest rate of adsorption among the adsorbents studied and therefore more detailed studies were carried out with this adsorbent. The influence of particle size, temperature, and thermal regeneration on adsorption of phenol by HiSiv 1000 was evaluated. From particle size experiments it appeared that adsorption capacity of HiSiv 1000 did not change by changing the particle size, but the rate of adsorption decreased considerably by increasing the particle size. The effect of temperature on adsorption was studied by determining equilibrium isotherms for HiSiv 1000 at 25, 40, and 55 degrees C. The results showed that adsorption capacity decreased with increasing temperature. Thermal regeneration of HiSiv 1000 was performed at 360 degrees C. It was observed that adsorption capacity of HiSiv 1000 did not change after 14 regeneration cycles. Equilibrium experiments showed that the adsorption capacities of activated carbon and Filtrasorb-400 were several times higher than that of HiSiv 1000.     

不同粒径土壤中重金属的分布规律

本文选择提钒炼钢厂内部分土壤为研究对象,测定了重金属元素（镉、铜、铬、铅、锌）的含量,并与样品粒度大小的关系进行了探讨,结果表明金属（铜、铬、铅、锌、镉）的浓度最大值出现在粒径较小（100目或160目）的样品中,同时将测定结果与土壤环境质量标准比较,结果表明镉、锌存在污染,其余元素均未超标。     

生物质热解影响因素研究

阐述了生物质的特点及其热解的定义和热解机理,综述了生物质热解过程中,温度、升温速率、物料特性（如种类、分子结构、粒径和颗粒形状等）、滞留时间、压力等操作条件对生物质热解及其产物分布组成和特性的影响,指出了生物质热解的技术关键。     

Optimization of the recovery of plastics for recycling by density media separation cyclones

Material recovery processes are presented as the optimum option for recycling plastic wastes as a means of recovering hydrocarbon resources. There exist a large variety of automated material recovery processes for recycling of such wastes but each with significant limitations. Of these, the separation based on differences in densities is advocated as the optimum process either for producing recycled products or preparing wastes for subsequent recovery processing.Density separation processes based on cyclone type density media separation (DMS) is presented as an important, potential method for increasing plastics recycling process capacities. It is demonstrated to have the capacity to separate a significantly larger range of particle sizes than those presently processed industrially. The mathematical relationship for the prediction of quality of typical LARCODEMS type density media separations by particle size and density as expressed by the Ecart Probable is presented.A proposed device configuration is presented for density media separation to optimize the recovery and purity of both density fractions produced. It is also suggested that to be economically viable, a large scale of operation is required for industrial plastics recycling operations recovering and producing a number of different plastics with a purity to be used as a substitute for virgin material.     

Bacterial desulfurization of Turkish lignites

The applicability of bacterial coal desulfurization to Turkish lignites and Nalligan-Cayirhan lignites was investigated in shake-flask culture systems. Effect of various parameters such as pulp density, particle size, type of inoculum, media and temperature on the efficiency of desulfurization by Thiobacillus ferrooxidans were tested. A Thiobacillus related moderately thermophilic mixotroph was found to remove some of the organic sulfur as well.