The use of Microtox to assess toxicity removal of industrial effluents from the industrial district of Camaçari (BA, Brazil)

The treatment efficiency, as toxicity removal, of complex effluents from the Industrial District of Cama?ari (BA, Brazil), after biological treatment with activated sludge was evaluated using Microtox. Samples of the equalised effluent (EE) were collected prior to treatment together with samples of the treated effluent (TE), which remained 24 h in the treatment plant. Rehydrated colonies of Vibrio fischeri were exposed to sequential dilutions of EE and TE to assess luminosity interference. Values for EC50 were calculated, together with the respective toxicity units. In all, twenty assays of each effluent type were carried out and the mean toxicity removal was 92.71%, while the chemical oxygen demand (COD) presented mean reduction of 83.04%. There was a variability of an order of magnitude between the Microtox results for the two types of effluents. The mean EC50 values were 2.12 for EE and 47.78% for TE. In spite of its weakness in some conditions, the Microtox system demonstrated to work adequately in assessing effluent toxicity removal in this treatment plant and therefore can be used for further toxicity removal programs.     

Use of a general toxicity test to predict heavy metal concentrations in residential soils

Significant clusters of developmental delay and mental retardation (DD/MR) were identified in children born in South Carolina. Although it is difficult to identify one factor that causes DD/MR, environmental insult including exposure of pregnant women to heavy metals can induce DD/MR in their children. Because it is expensive to measure the concentrations of individual metals in large numbers of environmental samples, the general Microtox toxicity test was used to identify highly toxic soil samples. Approximately 100 soil samples were collected from residential areas and analyzed to determine an effective concentration (EC(50)) of soil required to inhibit 50% light emission of the luminescent bacterial test organism (Vibrio fischeri). The EC(50) values were then transformed to relative toxicity units (RTU). A subset of 56 high and low toxicity soil samples was then analyzed by inductively coupled plasma-atomic emission spectrometry (EPA method 6010) for arsenic, lead, and chromium, which are known neurotoxins. The highest measured arsenic concentration was 30 times higher than the South Carolina residential soil limit. Significant correlations were found between the RTU and soil arsenic and chromium concentrations. Microtox also identified some low arsenic and chromium samples as toxic, presumably because additional unidentified toxicants were present in the soil. In general, however, the Microtox test was effective in identifying soils with elevated concentrations of arsenic and chromium, even in residential neighborhoods where limited soil toxicity was expected.     

Toxicity assessment of collected fractions from an extracted naphthenic acid mixture

Recent expansion within the oil sands industry of the Athabasca Basin of Alberta, Canada has led to increased concern regarding process-affected wastewaters produced during bitumen extraction. Naphthenic acids (NAs) have been identified as the primary toxic constituents of oil sands process-affected waters (OSPW) and studies have shown that with time, microbial degradation of lower molecular weight NAs has led to a decrease in observed toxicity. As earlier studies identified the need for an "unequivocal demonstration" of lower molecular weight NAs being the primary contributors to mixture toxicity, a study was initiated to fractionate an extracted NA mixture by molecular weight and to assess each fraction's toxicity. Successful molecular weight fractionation of a methylated NA mixture was achieved using a Kugelrohr distillation apparatus, in which fractions collected at higher boiling points contained NAs with greater total carbon content as well as greater degree of cyclicity. Assays with Vibrio fischeri bioluminescence (via Microtox assay) revealed that the lowest molecular weight NAs collected had higher potency (EC50: 41.9+/-2.8 mg l(-1)) than the highest molecular weight NAs collected (EC50: 64.9+/-7.4 mg l(-1)). Although these results support field observations of microbial degradation of low molecular weight NAs decreasing OSPW toxicity, it is not clear why larger NAs, given their greater hydrophobicity, would be less toxic.     

Effect of sediment turbidity and color on light output measurement for Microtox Basic Solid-Phase Test

In this work, sediment samples collected from several Spanish harbours were tested with two toxicity procedures, designed for solid samples: the Microtox Basic Solid-Phase Test (BSPT) and a modified procedure of the previous test protocol (mBSPT). According to the BSPT procedure, after initial light readings, pure bacteria were exposed to sediment suspension dilutions and light production was directly measured on suspended sediments without any further manipulation. As measurements are likely to be affected by sediment turbidity and color, a variation in initial light measurement has been here suggested, in order to consider the sample effect at all time readings during the test. Firstly, when sediment suspensions at different concentrations were added to bacteria suspension, immediately the initial light output drastically decayed by more than 50% in signal difference, resulting in a false inhibition, as effect of sample turbidity/color. This effect was more evident at high EC50 values, when slightly or not toxic samples were assessed. Secondly, the comparison of the EC50 obtained with both procedures, demonstrated that the mBSPT produced higher EC50 values (less toxic) than those obtained with the standard procedure. The mBSPT procedure resulted rapid and effective and it could be applied simultaneously with BSPT, in order to better evaluate the toxicity.     

Acute toxicity and genotoxicity of aquatic hydrophobic pollutants sampled with semipermeable membrane devices

Triolein-filled semipermeable membrane devices (SPMDs) were deployed for 4 weeks in polluted water sources in Lithuania. The mixtures of pollutants sampled by the SPMDs were fractionated by size-exclusion chromatography (SEC). The fraction containing average molecular weight compounds such as polycyclic aromatic hydrocarbons (PAHs) and organochlorine pesticides was screened by gas chromatography and mass spectrometry. The whole (non-fractionated) samples and their SEC fractions were tested in bioassays including Microtox, Mutatox, Daphnia pulex immobilization assay and the sister chromatid exchange (SCE) in human lymphocytes in vitro test. The Microtox test was most sensitive with the estimated EC(50) values in the range of milligrams or even micrograms per milliliter based on the amount of the SPMD triolein. Part of the observed toxicity was caused by elemental sulfur co-sampled by the SPMDs from sediments. The sum of toxicity equivalents of the SEC fractions was smaller than the relative toxicity of the whole samples indicating the presence of synergistic interactions in the complex mixtures of chemical pollutants. The toxic or genotoxic response induced by the chemical mixtures and their fractions was smaller in the D. pulex, Mutatox and SCE tests. In Mutatox, a positive response was only detected without the S9 metabolic activation which indicates the presence of mainly direct-acting mutagens in the samples. Interpretation of the Mutatox data was difficult due to the complexity of dose-response and time-response relationships. The study has demonstrated the potential as well as some limitations of SPMDs in the monitoring of biological effects of bioavailable organic pollutants in the aquatic environment.     

Temporal ecological assessment of oil contaminated soils before and after bioremediation

Ecotoxicity methods were used to assess different soil and oil combinations before, during and after laboratory bioremediation with associated hydrocarbon analysis. Heavy, medium and light crude oil (API gravity 14, 30, and 55) was spiked (ca. 5% w/w) into two sandy soils in the laboratory having organic carbon concentrations of 0.3 (Norwood) and 4.7% (Norwood/Baccto). The earthworm (Eisenia fetida) 14-d lethality assay, the modified Microbics Microtox Solid-Phase assay, and the 14-d plant seed germination and growth assays using corn, wheat and oats, were spiked and tested during a 360-d laboratory remediation. Eisenia was the most sensitive of the three methods utilized with survival increasing throughout bioremediation with fastest toxicity reduction in the high carbon Norwood/Baccto soils where LC50's were 100% or greater at the end of 90-d whereas, > 150-d were required to achieve a similar result in the low carbon soil. Analysis of the undiluted treatments with oily soil alone showed that earthworm survival was high after 90-d in all high organic carbon soils, and after eight months in the low carbon soils, except for the Norwood soil-light oil treatment, which required 360-d to achieve 100% survival. The Microtox assay was less sensitive with EC50's 100% or greater observed after 90-d in high carbon soils and after 240-d for all low carbon soils. After bioremediation, no effects on seed germination were observed, although some plant growth inhibition effects remained. There was no direct correlation between total petroleum hydrocarbon concentrations and toxicity.     

Enhanced Cr bioleaching efficiency from tannery sludge with coinoculation of Acidithiobacillus thiooxidans TS6 and Brettanomyces B65 in an air-lift reactor

Bioleaching process has been demonstrated to be an effective technology in removing Cr from tannery sludge, but a large quantity of dissolved organic matter (DOM) present in tannery sludge often exhibits a marked toxicity to chemolithoautotrophic bioleaching bacteria such as Acidithiobacillus thiooxidans. The purpose of the present study was therefore to enhance Cr bioleaching efficiencies through introducing sludge DOM-degrading heterotrophic microorganism into the sulfur-based sludge bioleaching system. An acid-tolerant DOM-degrading yeast strain Brettanomyces B65 was successfully isolated from a local Haining tannery sludge and it could metabolize sludge DOM as a source of energy and carbon for growth. A combined bioleaching experiment (coupling Brettanomyces B65 and A. thiooxidans TS6) performed in an air-lift reactor indicated that the rates of sludge pH reduction and ORP increase were greatly improved, resulting in enhanced Cr solubilization. Compared with the 5 days required for maximum solubilization of Cr for the control (single bioleaching process without inoculation of Brettanomyces B65), the bioleaching period was significantly shorten to 3 days for the combined bioleaching system. Moreover, little nitrogen and phosphorous were lost and the content of Cr was below the permitted levels for land application after 3 days of bioleaching treatment.     

Response of antioxidants in sunflower (Helianthus annuus L.) grown on different amendments of tannery sludge: its metal accumulation potential

The interaction of metals present in tannery waste and their tolerance in the plants of sunflower (Helianthus annuus L.) was studied in the present paper under field conditions. Effects of 100% tannery sludge and various amendments of tannery sludge (10%, 25%, 35%, 50%, 75%) along with one set of control were studied on the physiological and biochemical parameters of the plant along with their metal accumulation potential after 30, 60 and 90 d after sowing. The plants of H. annuus were found effective in the accumulation of metals (Cr, Fe, Zn and Mn) in roots, shoots and leaves, however, the level of toxic metal, Cr was found below detection limit in the seeds of the plant. The oil was extracted from the seeds of the plant and the level of oil content was increased up to 35% tannery sludge as compared to control followed by decrease at higher tannery sludge ratio. An increase in the chlorophyll, protein, cysteine, non-protein thiol and sugar contents was observed at the lower amendment of tannery sludge at initial exposure periods followed by decrease than their respective controls. Malondialdehyde content in the roots and leaves was increased beyond 50% sludge amendments at all the exposure periods as compared to control. However, proline and ascorbic acid contents of the roots and leaves of the plant increased at all the exposure periods and sludge amendments, compared to their respective controls.     

Patterns of metals and arsenic poisoning in Vibrio fischeri bacteria

The Microtox bioassay was used to establish dose-response curves for some toxic elements in aqueous solutions, namely, Zn(II), Pb(II), Cu(II), Hg(II), Ag(I), Co(II), Cd(II), Cr(VI), As(V) and As(III). Experiments were carried out at either pH 6.0 or pH 7.0 to indicate that pH may influence the measured toxicity of some elements due to pH-related changes of their chemical speciation. EC20 values, which represent a measurable threshold of toxicity, were determined for each element and were found to rank as Pb(II)>Ag(I)>Hg(II) approximately Cu(II)>Zn(II)>As(V)>Cd(II) approximately Co(II)>As(III)>Cr(VI). These values were compared to the limit concentrations allowed in industrial wastewater according to the official regulations in Catalonia (Spain). It appears that the Microtox test is sensitive enough for detecting some of the tested elements with respect to official regulations of Catalonia (Spain) dealing with pollution control, with the exception of cadmium, mercury, arsenate, arsenite and chromate.     

Toxicity of combined sewer overflows on river phytoplankton: the role of heavy metals

The toxic effect of a combined sewer overflow (CSO) on the phytoplankton community of the river Seine has been studied by means of short-term primary production measurements. As the discharged solids usually do not remain in the water column, only filtered or centrifugated fractions were tested. The collected phytoplankton were grown in the laboratory for 2 days, after addition of N, P and EDTA. Stock cultures in exponential growth were directly tested with heavy metals, but resuspended algal cells were used for effluent testing. The results show an increase of EC50 value for the single metal species in the order Cu相似文献   

Preparation of acidic and alkaline macrocapsules for pH control

A series of experiments was performed to prepare acidic macroencapsulated buffers composed of 20% Ca(H2PO4)(2) and 80% Eudragit S 100 polymer and alkaline macrocapsules composed of 65% K2HPO4 and 35% Eudragit E PO polymer (the powdered form of Eudragit E 100). Eudragit S 100 was shown to be soluble at a pH greater than 7.0, while Eudragit E 100 was soluble at a pH less than 7.0. Both polymers did not impart significant biochemical oxygen demand. The Eudragit E PO polymer solution showed low toxicity (EC50=91%) based on the Microtox Acute Toxicity Test compared to the 0.1mM background phosphate buffer solution (EC50=100%) while the Eudragit S 100 polymer solution showed higher toxicity (EC50=53%). Batch tests showed that the acidic macrocapsules reduced the pH of a 0.1mM phosphate solution from 11 to neutral, while the alkaline macrocapsules increased the pH of a 0.1mM phosphate solution from 3 to neutral. The macrocapsules could potentially be used as an in situ proportional pH controller for groundwater remediation.     

Application of the Microtox test and pollution indices to the study of water toxicity in the Albufera Natural Park (Valencia, Spain)

The toxic effects of waters collected from irrigation channels in a Mediterranean wetland (Albufera Natural Park, Valencia, Spain) were tested with the Microtox assay and compared with six pollution indices (PIs) defined from analytical parameters. Chemical oxygen demand (COD), biological oxygen demand (BOD), nutrients, heavy metals and pesticides were measured. The bioassay result (concentrations of the water sample (% V/V) that reduced light emission to 10%, 20% and 50%, EC10, EC20 and EC50, respectively (ECs)) was compared with the PIs. This comparison has demonstrated a general agreement between ECs and PIs, except in the case of irrigation channels affected by herbicides used in rice farming (molinate and thiobencarb). No pronounced inhibition was detected in the bioluminescence in relation to the eutrophic parameters in the irrigation waters for EC50 values, indicating that this parameter does not suffice to detect eutrophic waters. Data derived from irrigation water pollution and bioassay were assembled by multivariate statistical techniques (principal component analysis). These components were associated with various contamination sources.     

皮革废水经微电解-SBR处理后的综合毒性变化

选择蛋白核小球藻（Chlorella pyrenoidosa Chick）为供试藻种,采用藻类急性毒性试验考察皮革废水经微电解-SBR工艺处理后的综合毒性变化情况。结果表明,皮革废水经微电解-SBR工艺处理后,其综合毒性显著降低。分别以细胞数和活体叶绿素a含量计算得到的原水、微电解出水和SBR出水的EbC50值和EeC50值依次为16.6%、19.3%、52.6%和13.0%、15.6%和52.1%。根据Bulich提出的毒性等级划分原则,经处理后最终出水的毒性级别由原水的Ⅰ级降为Ⅱ级。     

Petroleum refinery secondary effluent polishing using freezing processes--toxicity and organic contaminant removal

A petroleum refinery secondary effluent was treated using two freezing techniques--spray freezing and unidirectional downward freezing (UDF). The freezing processes were effective to remove toxicity and total organic carbon (TOC)- and chemical oxygen demand (COD)-causing materials in the effluent. Agitation of the liquid during UDF significantly improved the impurity separation efficiency; 85 to 96% removal of TOC and COD was achieved without any pretreatment and freezing only 70% of the feed water. The treatment efficiency of the spray freezing was at the same level as that of UDF without mixing. The spray ice with longer storage time released more contaminants with early meltwater. The initial contaminant concentration of the feed water and the freezing temperatures (-10 degrees C and -25 degrees C) had no significant influence on the treatment efficiency. A small fluctuation in effluent TOC concentration caused a dramatic change in effluent toxicity (Microtox). The effective concentration (EC20) (Microtox) was effective in detecting effluent toxicity.     

A mathematical algorithm to identify toxicity and prioritize pollutants in field sediments

In order to evaluate sediment toxicity, a mathematical algorithm was developed to compute the toxicity of multiple component mixtures acting in an additive manner. A statistical approach was devised to determine the presence of potential interactive effects among mixture components. The algorithm uses three kinds of data to obtain an integrative approach to sediment toxicity assessment: Microtox toxicity data (EC50 values), sediment pollutant concentration measurements, and sequential extraction (SEQ) data to investigate metal partitioning. To simplify the analysis of complex mixtures using a prioritization scheme based on intrinsic toxicity and relative abundance, a toxicity index (TI) was employed as an indicator of adverse ecological impact. In general, the ranking of contaminants using the TI approach was found to be most efficient in reducing computational time, and concentrations using bioavailability data from SEQ was found to be the best theoretical predictor of the experimental mixture toxicity value. Only a few pollutants that were present at the greatest abundance were needed to provide a good approximation of the calculated EC50 found when all components were included. Not only does this substantially reduce the computational time needed to determine the EC50, it could in some cases dramatically reduce the pollutant monitoring effort required to track toxicity effectively. This approach would have substantial implications for both risk assessment and for remediation strategies, making them more efficient by focusing on the priority pollutants identified.     

Chemical fractionation and heavy metal accumulation in the plant of Sesamum indicum (L.) var. T55 grown on soil amended with tannery sludge: Selection of single extractants

A pot experiment was carried out to study the single and sequential extractions of metals in different tannery sludge amendment and the potential of the plant of Sesamum indicum L. var. T55 (sesame) for the removal of metals from tannery waste contaminated site. The metal extraction efficiency obtained with each extractants was slightly different and follow the order; EDTA>DTPA>NH(4)NO(3)>NaNO(3)>CaCl(2). The correlation analysis between extractable metals in the different amendments of sludge and metal accumulation in the plant (lower and upper parts) showed better correlation for most of the tested metals with EDTA extraction. In this study, a sequential extraction technique was applied on different amendments of tannery sludge. The results showed that Mn, Zn, Cr and Cd were mostly associated with Fe-Mn oxide fraction in most of the amendments, K and Ni was found in residual (RES) fraction, Fe and Cu was bound with organic matter (OM) and RES fractions and Na was associated with carbonate (CAR) fraction. The metal accumulation after 60 d of growth of the plant was found in the order of K>Na>Fe>Zn>Cr>Mn>Cu>Pb>Ni>Cd and its translocation was found less in upper part. The accumulation of toxic metals (Cr, Ni and Cd) in the plants was found to increase with increase in sludge ratio, in contrast, the accumulation of Pb decreased. In view of growth parameters and metal accumulation in the plant, it was observed that lower amendments (25%) of tannery sludge were found suitable for the phytoremediation of most of the studied metals.     

Microtox testing of pentachlorophenol in soil extracts and quantification by capillary electrochromatography (CEC)--a rapid screening approach for contaminated land

An approach to rapid soil testing which involved the use of simple solvent extraction methods was developed. The analytes of interest were priority pollutants of low water solubility which could not be readily removed from the soil using water. Direct toxicity testing of the soil samples by Microtox showed a high background toxicity which prevented realistic toxicity data from being obtained for the contaminants present. A range of different extraction solutions was used in an attempt to extract the contaminants while eliminating the matrix effects of the soil. It was necessary that the solvents selected for extraction of the soil samples were not of significant toxicity, as this could potentially mask the toxic effects of any compounds extracted from the soil. The extraction efficiencies of solvent systems were evaluated using pentachlorophenol (PCP) as a model compound of known toxicity in the Microtox assay. A rapid and cost-effective method was developed in order to determine the amount of PCP recovered from the soil by the extraction solvents employed. This method consisted of a solid phase extraction (SPE) step followed by quantification using capillary electrochromatography (CEC). Recoveries were greater when a higher proportion of organic solvent (methanol) was used in the extraction process, and lowest when water was used. An extraction based on water could provide information on the potential for leaching of contaminants from the soil into nearby water bodies in an environmental setting. An organic solvent extraction method could indicate how much toxicity soil-dependent organisms might be exposed to through ingestion. Extraction based on 50% (v/v) methanol in water was considered to be the most suitable overall extraction solution for soil screening, given that this permitted extraction of the water-insoluble compound PCP at a level which was clearly toxic in the Microtox assay while also retaining the capability to extract water-soluble contaminants.     

Microtox toxicity test: detoxification of TNT and RDX contaminated solutions by poplar tissue cultures

Poplar (Populus deltoidesxnigra DN34) tissue cultures removed 2,4,6-trinitrotoluene (TNT) from an aqueous solution in five days, reducing the toxicity of the solution from highly toxic Microtox EC value to that of the control. 1,3,5-Trinitro-1,3,5-triazacyclohexane (RDX) was taken up by the plant tissue cultures more slowly, but toxicity reduction of the solution was evident. The measurement of toxicity reduction of aqueous solutions containing TNT and RDX was performed using a novel methodology developed for use with the Microtox testing system. Radiolabeled TNT and RDX were used to confirm removal of explosives from hydroponic solutions containing plant tissue cultures and to verify that toxicity did not change in solutions where no plant cultures were present (positive controls). High Performance Liquid Chromatography (HPLC) and Liquid Scintillation Counter (LSC) measurements confirmed removal of TNT and RDX from solutions containing poplar plant tissue cultures and constancy of the plant-free controls. In addition, metabolites were identified in remediated solutions by HPLC, confirming the mechanism by which plants can remediate groundwater, surface water, and soil solutions.     

Trophic transfer of pyrene metabolites and nonextractable fraction from Oligochaete (Lumbriculus variegatus) to juvenile brown trout (Salmo trutta)

Cell lines of Etroplus suratensis established in our laboratory were evaluated for their potential use as screening tools for the ecotoxicological assessment of tannery effluent. The cytotoxic effect of tannery effluent in three cell lines derived from eye, kidney and gill tissue of E. suratensis was assessed using multiple endpoints such as Neutral Red (NR) assay, Coomassie Blue (CB) protein assay and Alamar Blue (AB) assay. Acute toxicity tests on fish were conducted by exposing E. suratensis for 96 h to tannery effluent under static conditions. The toxic effect of tannery effluent on the survival of fish was found to be concentration and time dependent. The tannery effluent at the concentration of 15% caused 100% mortality at 96 h whereas the lower concentration (0.5%) caused 13.33% mortality. The cytotoxicity of tannery effluent was found to be similar in the three cell lines tested, independent of the toxic endpoints employed. EC₅₀ values, the effective concentration of tannery effluent resulting in 50% inhibition of cytotoxicity parameters after 48 h exposure to tannery effluent were calculated for eye, kidney and gill cell lines using NR uptake, AB and cell protein assays. Statistical analysis revealed good correlation with r² = 0.95-0.99 for all combinations between endpoints employed. Linear correlations between each in vitro EC₅₀ and the in vivo LC₅₀ data, were highly significant p < 0.001 with r² = 0.977, 0.968 and 0.906 for AB₅₀, NR₅₀, and CB₅₀, respectively.     

Environmental labeling of car tires--toxicity to Daphnia magna can be used as a screening method

Car tires contain several water-soluble compounds that can leach into water and have toxic effects on aquatic organisms. Due to tire wear, 10,000 tonnes of rubber particles end up along the Swedish roads every year. This leads to a diffuse input of emissions of several compounds. Emissions of polyaromatic hydrocarbons (PAHs) are of particular concern. PAHs are ingredients of the high aromatic oil (HA oil) that is used in the rubber as a softener and as a filler. The exclusion of HA oils from car tires has started, and an environmental labeling of tires could make HA oils obsolete. The toxicity to Daphnia magna from 12 randomly selected car tires was tested in this study. Rubber from the tread of the tires was grated into small pieces, to simulate material from tire wear, and the rubber was equilibrated with dilution water for 72 h before addition of test organisms. The 24-h EC50s of the rubber pieces ranged from 0.29 to 32 gl-1, and the 48-h EC50s ranged from 0.0625 to 2.41 gl-1. Summer tires were more toxic than winter tires. After the 48-h exposure, the daphnids were exposed to UV-light for 2 h, to determine if the tires contained compounds that were phototoxic. After UV-activation the EC50s ranged from 0.0625 to 0.38 gl-1. Four of the 12 tires had a very distinct photoactivation, with a toxicity increase of >10 times. This study has shown that the used method for toxicity testing with Daphnia magna according to ISO 6341 could be used as a basis for environmental labeling of car tires.