Azo-dyes photocatalytic degradation in aqueous suspension of TiO2 under solar irradiation

The photodegradation of two common and very stable azo-dyes, i.e. methyl-orange (C₁₄H₁₄N₃SO₃Na) and orange II (C₁₆H₁₁N₂SO₄Na), is reported. The photocatalytic oxidation was carried out in aqueous suspensions of polycrystalline TiO₂ irradiated by sunlight. Compound parabolic collectors, installed at the “Plataforma Solar de Almería” (PSA, Spain) were used as the photoreactors and two identical reacting systems allowed to perform photoreactivity runs for the two dyes at the same time and under the same irradiation conditions. The disappearance of colour and substrates together with the abatement of total organic carbon content was monitored. The main sulfonate-containing intermediates were found to be in lower number in respect to those obtained under artificial irradiation. In particular there were no more evidence of the presence of hydroxylated transients. The dependence of dye photooxidation rate on: (i) substrate concentration; (ii) catalyst amount; and (iii) initial pH was investigated. The influence of the presence of strong oxidant species (H₂O₂, S₂O₈²⁻) and some ions (Cl⁻, SO₄²⁻) on the process was also studied.     

Assessment of solar driven TiO2-assisted photocatalysis efficiency on amoxicillin degradation

The objective of this work was to evaluate the efficiency of a solar TiO₂-assisted photocatalytic process on amoxicillin (AMX) degradation, an antibiotic widely used in human and veterinary medicine. Firstly, solar photolysis of AMX was compared with solar photocatalysis in a compound parabolic collectors pilot scale photoreactor to assess the amount of accumulated UV energy in the system (Q _UV) necessary to remove 20 mg L^?1 AMX from aqueous solution and mineralize the intermediary by-products. Another experiment was also carried out to accurately follow the antibacterial activity against Escherichia coli DSM 1103 and Staphylococcus aureus DSM 1104 and mineralization of AMX by tracing the contents of dissolved organic carbon (DOC), low molecular weight carboxylate anions, and inorganic anions. Finally, the influence of individual inorganic ions on AMX photocatalytic degradation efficiency and the involvement of some reactive oxygen species were also assessed. Photolysis was shown to be completely ineffective, while only 3.1 kJ_UV?L^?1 was sufficient to fully degrade 20 mg L^?1 AMX and remove 61 % of initial DOC content in the presence of the photocatalyst and sunlight. In the experiment with an initial AMX concentration of 40 mg L^?1, antibacterial activity of the solution was considerably reduced after elimination of AMX to levels below the respective detection limit. After 11.7 kJ_UV?L^?1, DOC decreased by 71 %; 30 % of the AMX nitrogen was converted into ammonium and all sulfur compounds were converted into sulfate. A large percentage of the remaining DOC was in the form of low molecular weight carboxylic acids. Presence of phosphate ions promoted the removal of AMX from solution, while no sizeable effects on the kinetics were found for other inorganic ions. Although the AMX degradation was mainly attributed to hydroxyl radicals, singlet oxygen also plays an important role in AMX self-photosensitization under UV/visible solar light.     

Photocatalytic degradation of isoproturon herbicide over TiO2/Al-MCM-41 composite systems using solar light

The present investigation covers immobilization of TiO2 using a simple solid state dispersion technique over mesoporous Al-MCM-41 support for the treatment of isoproturon herbicide. Catalysts are characterized by XRD, X-ray photo electron spectroscopy (XPS), surface area, UV-Vis diffused reflectance spectra (DRS), SEM and TEM. A detailed photocatalytic degradation study of isoproturon under solar light in aqueous suspensions is reported. The 10 wt% TiO2/Al-MCM-41 composite system found to be optimum with high degradation activity. The reaction follows pseudo-first order kinetics. The parameters like TiO2 loading over Al-MCM-41, amount of catalyst, concentration of substrate, pH effect, durability of the catalyst, activity comparison of TiO2 and Al-MCM-41 supported system are studied. The mineralization of isoproturon is monitored by TOC. Based on the degradation products detected through LC-MS, a plausible degradation mechanism is proposed. The data indicates that TiO2/Al-MCM-41 composite system is an effective photocatalyst for treatment of isoproturon in contaminated water.     

TiO2光催化氧化脱除模拟烟气中的NOx

采用P25纳米TiO2为催化剂,对NOx浓度360 mg/m3的模拟烟气进行了光催化氧化实验研究,以期为此种方法在电厂烟气脱硝方面的应用提供依据。经SEM、XRD等表征手段,探讨了催化剂晶型尺寸对光催化的作用。实验考察了光催化反应过程规律以及负载量、光照度、NO初始浓度、O2含量、相对湿度和停留时间对光催化氧化效率的影响。结果表明,光催化反应是瞬态到稳态的过程,其催化效率与上述影响因子有密切关系。实验最优条件下NOx的脱除率为46%,但只需适当提高氧化效能,便能达到理想的效果。     

TiO2薄膜光催化降解双酚A的研究

采用sol-gel法制备TiO2薄膜。以该薄膜为催化剂，研究了在H2O2存在的条件下，对内分泌干扰物质双酚A的光催化降解反应。分别讨论了pH值、H2O2的加入量、双酚A的初始浓度以及光照时间对降解反应的影响。结果表明，在pH=4，30mg／L的H2O2中对初始浓度为50mg／L的双酚A溶液光照180min有较好的降解效果。     

TiO2薄膜光催化降解双酚A的研究

采用sol-gel法制备TiO2薄膜.以该薄膜为催化剂,研究了在H2O2存在的条件下,对内分泌干扰物质双酚A的光催化降解反应.分别讨论了pH值、H2O2的加入量、双酚A的初始浓度以及光照时间对降解反应的影响.结果表明,在pH=4,30 mg/L的H2O2中对初始浓度为50 mg/L的双酚A溶液光照180 min有较好的降解效果.     

A comprehensive systematic review of photocatalytic degradation of pesticides using nano TiO2

Environmental Science and Pollution Research - This study has systematically reviewed all of the research articles about the photocatalytic degradation of pesticides using titanium dioxide (TiO2)...     

Photoassisted and photocatalytic degradation of sulfur mustard using TiO2 nanoparticles and polyoxometalates

The decomposition of highly toxic chemical warfare agent, sulfur mustard (bis(2-chloroethyl) sulfide or HD), has been studied by homogeneous photolysis and heterogeneous photocatalytic degradation on titania nanoparticles. Direct photolysis degradation of HD with irradiation system was investigated. The photocatalytic degradation of HD was investigated in the presence of TiO₂ nanoparticles and polyoxometalates embedded in titania nanoparticles in liquid phase at room temperature (33?±?2 °C). Degradation products during the treatment were identified by gas chromatography–mass spectrometry. Whereas apparent first-order kinetics of ultraviolet (UV) photolysis were slow (0.0091 min^?1), the highest degradation rate is obtained in the presence of TiO₂ nanoparticles as nanophotocatalyst. Simultaneous photolysis and photocatalysis under the full UV radiation leads to HD complete destruction in 3 h. No degradation products observed in the presence of nanophotocatalyst without irradiation in 3 h. It was found that up to 90 % of agent was decomposed under of UV irradiation without TiO₂, in 6 h. The decontamination mechanisms are often quite complex and multiple mechanisms can be operable such as hydrolysis, oxidation, and elimination. By simultaneously carrying out photolysis and photocatalysis in hexane, we have succeeded in achieving faster HD decontamination after 90 min with low catalyst loading. TiO₂ nanoparticles proved to be a superior photocatalyst under UV irradiation for HD decontamination.     

Photocatalytic degradation of 2,4-DNT in simulated wastewater by magnetic CoFe2O4/SiO2/TiO2 nanoparticles

Environmental Science and Pollution Research - Discharge of 2,4-dinitrotoluene (2,4-DNT) into the environment leads to a serious soil and water sources pollution problem, due to toxicity and...     

TiO2光催化涂料的制备及其降解甲醛研究

自制TiO2光催化涂料,重点对所制备的涂料在室内进行降解甲醛研究,考察了在不同分散剂、不同光催化剂以及不同甲醛初始浓度、不同光源、不同温度和不同湿度等环境因素下涂料对甲醛降解率的影响。结果表明,选用聚丙烯酸钠离子型分散剂,铜金属掺杂TiO2光催化剂制备的光催化涂料对甲醛降解率达80％以上且具有良好的耐久性,在室温（20℃左右）湿度50％日光灯照射下,甲醛初始浓度5μL时效果最佳。     

Solar TiO2-assisted photocatalytic degradation of IGCC power station effluents using a Fresnel lens

The heterogeneous TiO2 assisted photocatalytic degradation of wastewater from a thermoelectric power station under concentrated solar light irradiation using a Fresnel lens has been studied. The efficiency of photocatalytic degradation was determined from the analysis of cyanide and formate removal. Firstly, the influence of the initial concentration of H2O2 and TiO2 on the degradation kinetics of cyanides and formates was studied based on a factorial experimental design. Experimental kinetic constants were fitted using neural networks. Results showed that the photocatalytic process was effective for cyanides destruction (mainly following a molecular mechanism), whereas most of formates (degraded mainly via a radical path) remained unaffected. Finally, to improve formates degradation, the effect of lowering pH on their degradation rate was evaluated after complete cyanide destruction. The photooxidation efficiency of formates reaches a maximum at pH around 5-6. Above pH 6, formate anion is subjected to electrostatic repulsion with the negative surface of TiO2. At pH<4.5, formate adsorption and photon absorption are reduced due to some catalyst agglomeration.     

TiO2/GeO2复合膜光催化氧化降解农药废水的研究

提出了一种新的TiO2/GeO2复合膜圆形光催化氧化反应器,研究了该反应器对经物化处理后的农药废水进行降解的过程。研究表明,光催化氧化的最佳条件是锌片镀TiO2/GeO2复合膜、pH=6.7、过氧化氢（H2O2）浓度为400 mg/L。并对其他氧化剂对该过程的影响进行了探讨。有机废水通过该反应器处理后,其COD值降为57mg/L。能使有机污染物全部降解为小分子无机物,废水达到国家一级排放标准。     

Effects of dissolved oxygen, pH, and anions on the 2,3-dichlorophenol degradation by photocatalytic reaction with anodic TiO(2) nanotube films

In this study, the highly-ordered TiO(2) nanotube (TNT) arrays on titanium sheets were prepared by an anodic oxidation method. Under UV illumination, the TNT films demonstrated the higher photocatalytic activity in terms of 2,3-dichlorophenol (2,3-DCP) degradation in aqueous solution than the conventional TiO(2) thin films prepared by a sol-gel method. The effects of dissolved oxygen (DO) and pH on the photocatalytic degradation of 2,3-DCP were investigated. The results showed that the role of DO in the 2,3-DCP degradation with the TNT film was significant. It was found that 2,3-DCP in alkaline solution was degraded and dechlorinated faster than that in acidic solution whereas dissolved organic carbon removal presented an opposite order in dependence of pH. In the meantime, some main intermediate products from 2,3-DCP degradation were identified by a (1)H NMR technique to explore a possible degradation pathway. A major intermediate, 2-chlororesorcinol, was identified from the 2,3-DCP decomposition as a new species compared to the findings in previous reports. Photocatalytic deactivation was also evaluated in the presence of individual anions (NO(3)(-), Cl(-), SO(4)(2-), and H(2)PO(4)(-)). The inhibition degree of photocatalytic degradation of 2,3-DCP caused by these anions can be ranked from high to low as SO(4)(2-)>Cl(-)>H(2)PO(4)(-)>NO(3)(-). The observed inhibition effect can be attributed to the competitive adsorption and the formation of less reactive radicals during the photocatalytic reaction.     

Study on the photocatalytic degradation of glyphosate by TiO(2) photocatalyst

In this paper, the photocatalytic degradation of glyphosate selected as the deputy of organic pollutant in aqueous solution with TiO(2) powder as a photocatalyst has been studied. The effects of various parameters, such as the amount of the photocatalyst, illumination time, initial pH value, electron acceptors, metal ions, and anions on the photocatalytic degradation of glyphosate were investigated. From the studies, the best condition for the effect of the parameters on the photocatalytic degradation of glyphosate was obtained. The results show that the optimum amount of the photocatalyst used is 6.0 g l(-1) for the photocatalytic reactions. The photodegradation efficiency of glyphosate increases with the increase of the illumination time. With the addition of Fe(3+), Cu(2+), H(2)O(2), K(2)S(2)O(8) or KBrO(3), the photocatalytic degradation of glyphosate is accelerated. However, with the addition of Na(+), K(+), Mg(2+), Ca(2+), Zn(2+), Co(2+) and Ni(2+), or with the addition of trace amounts of Cl(-), Br(-), SO(4)(2-), there are no obvious effects on the reactions. Acidic or alkaline mediums are favorable for the photocatalytic degradation of glyphosate. The possible roles of the additives on the reactions and the possible mechanisms of effect were discussed.     

TiO2光催化处理水中苯酚的环境风险研究

利用薄膜水循环TiO2光催化反应器(TiO2-WFCPR)处理水中苯酚的实验数据,分析了不同处理条件下苯酚光催化降解过程中间产物的降解规律和出水的环境风险.研究结果表明,即使苯酚已达<污水综合排放标准>(GB 8978-1996)一级排放标准,但出水中还不同程度地存在有害的中间产物,排放时会对环境造成危害,因此应以残留苯酚及其中间产物的浓度及影响确定该工艺最终的反应时间.足够的反应时间和偏碱性条件是降低苯酚及其中间产物环境风险的关键因素.苯酚初始浓度及进水pH越高,苯酚达标的反应时间会越长,处理的经济性就越差.所以,从环境风险与经济性综合考虑,该工艺适用于处理苯酚初始质量浓度≤60.00 mg/L的水,适宜的pH为6.0～8.0.     

Study on photocatalytic degradation of gaseous dichloromethane using pure and iron ion-doped TiO2 prepared by the sol-gel method

The synthesis of TiO₂ and Fe–TiO₂ by sol–gel method is demonstrated and characterized. The characterization of TiO₂ and Fe–TiO₂ is performed with instruments, including TGA/DTA, FTIR, UV–Vis, N₂ adsorption and SEM. Dichloromethane is used for the photocatalytic activity test. From the results of dichloromethane photocatalyitc degradation, the calcined temperature of TiO₂ and the presence of water vapor influence the photocatalytic activity. The optimum doping amount of iron ions is 0.005 mol%, and this can enhance the photocatalytic activity, while too great an amount will make the iron ions become recombination centers for the electron–hole pairs and reduce the photocatalytic activity. UV–Vis diffuse reflectance spectra of Fe–TiO₂ show an increase in absorbency in the visible light region with the increase in iron ions doping concentration The intermediate of dichloromethane photodegradation includes CHCl₃, CCl₄, CH₂Cl₂ and COCl₂. The presence of iron ions may reduce the adsorption of Cl element on the surface of the photocatalyst.     

A statistical modeling-optimization approach for photocatalytic degradation of diflouro triazole acetophenone using Ag-Fe co-doped TiO2: response surface methodology

Environmental Science and Pollution Research - In this research, the performance of Ag-Fe co-doped TiO2 (Ag-Fe CT) nanophotocatalyst for degradation of diflouro triazole acetophenone (DTA) from...     

State-of-the-art and current challenges for TiO2/UV-LED photocatalytic degradation of emerging organic micropollutants

Environmental Science and Pollution Research - The development of ultraviolet light-emitting diodes (UV-LED) opens new possibilities for water treatment and photoreactor design. TiO2...     

Performance of photocatalytic reactors using immobilized TiO2 film for the degradation of phenol and methylene blue dye present in water stream

TiO2 thin film photocatalyst was successfully synthesized and immobilized on glass reactor tube using sol-gel method. The synthesized TiO2 coating was transparent, which enabled the penetration of ultra-violet (UV) light to the catalyst surface. Two photocatalytic reactors with different operating modes were tested: (a) tubular photocatalytic reactor with re-circulation mode and (b) batch photocatalytic reactor. A new proposed TiO2 synthesized film formulation of 1 titanium isopropoxide: 8 isopropanol: 3 acetyl acetone: 1.1 H2O: 0.05 acetic acid (in molar ratio) gave excellent photocatalytic activity for degradation of phenol and methylene blue dye present in the water. The half-life time, t1/2 of photocatalytic degradation of phenol was 56 min at the initial phenol concentration of 1000 microM in the batch reactor. In the tubular photocatalytic reactor, 5 re-circulation passes with residence time of 2.2 min (single pass) degraded 50% of 40-microM methylene blue dye. Initial phenol concentration, presence of hydrogen peroxide, presence of air bubbling and stirring speed as the process variables were studied in the batch reactor. Initial methylene blue concentration, pH value, light intensity and reaction temperature were studied as the process variables in the tubular reactor. The synthesized TiO2 thin film was characterized using SEM, XRD and EDX analysis. A comparative performance between the synthesized TiO2 thin film and commercial TiO2 particles (99% anatase) was evaluated under the same experimental conditions. The TiO2 film was equally active as the TiO2 powder catalyst.