环境内分泌干扰物诱发小鼠睾丸细胞DNA损伤的研究

应用单细胞凝胶电泳技术技术，研究了烷基酚类化合物对离体小鼠睾丸细胞DNA的损伤作用。实验结果表明，9种烷基酚类化合物对小鼠睾丸细胞均能引起不同程度的DNA损伤，并呈现剂量效应关系，其高剂量组与对照组相比，均有极显著性差异（P＜0．01）。实验结果亦表明，其DNA的损伤程序与化学结构有一定的关系。     

施加磷元素后对小麦抗重金属铜毒性的影响

将小麦幼苗放在含有不同浓度磷元素(1 mmol/L和10 mmol/L)和铜元素(0.16μmol/L、100μmol/L和1 mmol/L)的培养液中处理12 h后,观察植物体内铜元素的含量、叶绿素含量、抗坏血酸循环的变化.结果表明,当培养液中施加的铜元素浓度相同时,施加较高浓度的磷(10 mmol/L)能促进植物根部吸收和积累铜,并能促进铜元素从根部向地上部的运输.此外,实验结果还表明,当培养液中都含有较少量的铜(0.16μmol/L)元素时,比较磷浓度对植物体内生理反应的影响时,发现在含有高浓度磷的培养液中培养的小麦体内的受到较少的膜质过氧化损伤,光合色素的含量保持稳定.但是,当培养液中有较高浓度的铜元素(100μmol/L和1 mmol/L)时,施加高浓度的磷反而加剧了植物体内的膜质过氧化损伤和引起光合色素的分解,从而不利于植物正常的生长发育.     

罗丹明6G共振散射光谱法测定水中痕量六价铬

在 0 .0 4mol/L H2 SO4 和 8.0× 10 - 4mol/L KI介质中 ,罗丹明 6G ( Rh G)在 5 80 nm处有 1个同步荧光峰。当有 Cr( )存在时 ,Cr( )与过量的 I-反应生成 I- 3,I- 3与 Rh G形成缔合微粒 ,在 32 0、40 0、5 95 nm处产生 3个共振散射 ( RS)峰 ;而在 5 80nm处荧光峰猝灭。六价铬浓度在 1.0× 10 - 7～ 2 0× 10 - 7mol/L范围内与 40 0 nm波长处的共振散射光强度成线性关系。据此建立了测定水中六价铬的共振散射光谱分析法。光谱研究结果表明 ,( Rh G-I3) n缔合微粒和界面的形成是导致体系 RS增强的根本原因。     

不同来源腐殖质淋洗去除土壤中Cd、Pb的研究

针对耕地土壤Cd、Pb污染问题,选取3种提取剂(提取剂 Ⅰ:1.0 mol/L NaOH;提取剂 Ⅱ:0.1 mol/L NaOH+0.1 mol/L Na4P2O7;提取剂Ⅲ:0.1 mol/L KOH+0.1 mol/L K4P2O7)分别从5种物料中(风化褐煤、污泥、鸡粪、泥炭土、牛粪)中提取腐殖质(HS)淋洗去...     

过硫酸钾脱除气态元素汞的试验研究

在鼓泡塔反应器中,用过硫酸钾(K2S2O8)脱除气态元素汞.试验考察了K2S2O8浓度、吸收温度及催化剂等因素对脱汞效率的影响.结果表明:当K2S2O8在1.0～10.0 mmol/L时,随着浓度的增加,脱汞效率显著升高;AgNO3对K2S2O8脱汞具有显著的催化作用,且0.3 mmol/L AgNO3的催化效果优于0.1 mmol/L AgNO3;CuSO4对K2S2O8除汞也具有催化作用,但催化效果不如AgNO3;AgNO3存在下,低温更有利于汞的脱除.     

产木聚糖酶嗜碱细菌的筛选及产酶条件研究

利用透明圈法筛选到一株产木聚糖酶的嗜碱芽孢杆菌NT 9,该菌株产木聚糖酶为组成型。正交设计实验结果表明 ,合适的产酶条件为 :木糖 15 .0g/L ,硫酸铵 2 .5 g/L ,Tween 80 2 0 g/L ,K2 HPO4 1.0g/L ,MgSO4 ·7H2 O 0 .2g/L ,pH值 10 .0 ,3 7℃ ,2 0 0r/min ,振荡培养 72h。其木聚糖酶活力可达到 6.3 6IU/mL。     

不同Cd2+浓度与硝酸盐浓度、磷酸盐浓度交互作用对杜氏盐藻生长及叶绿素荧光特性的影响

研究了不同Cd2+浓度与硝酸盐浓度、磷酸盐浓度交互作用对杜氏盐藻(Dunaliella salina)生长及叶绿素荧光特性的影响.结果表明,Cd2+浓度与硝酸盐浓度、磷酸盐浓度对杜氏盐藻的光合作用及生长均具有显著影响(P＜0.05);Cd2+胁迫24 h后,杜氏盐藻的荧光参数Fv/Fm、Fv/Fo、Yield、rETR、细胞密度和叶绿素相对含量均与Cd2+浓度表现为显著的负相关;在低硝酸盐摩尔浓度(55μmol/L)下,杜氏盐藻的荧光参数Fv/Fm、Fv/F.、Yield、rETR、细胞密度和叶绿素相对含量均明显下降;在高硝酸盐摩尔浓度(7 040 μmol/L)下,杜氏盐藻的上述荧光参数下降幅度小;在正常硝酸盐摩尔浓度(880 μmol/L)下,杜氏盐藻荧光参数Fv/Fo、NPQ和叶绿素相对含量均最高,对Cd2+的耐受性更强;在低磷酸盐摩尔浓度(2.27 μmol/L)下,杜氏盐藻的荧光参数(除NPQ外)、细胞密度和叶绿素相对含量均显著低于对照组和高磷处理组,表现为磷限制现象;在离磷酸盐摩尔浓度(290.40 μmol/L)下,杜氏盐藻的荧光参数(除NPQ外)、细胞密度和叶绿素相对含量均明显高于低磷处理组和对照组,杜氏盐藻受Cd2+胁迫程度最小.     

磷浓度对海洋小球藻叶绿素荧光及生长的影响

海水富营养化影响微藻生长,引起海洋初级生产力变化.以海洋小球藻(Chlorella sp.)为研究对象,研究不同磷浓度对其叶绿素荧光、细胞密度和色素含量变化的影响,以期找到海洋小球藻最适生长的磷浓度,为富营养条件下微藻生长的研究提供基础资料.结果表明,在培养温度为(22±1) ℃、光照强度为4 000 lx、光暗比为12 h:12 h条件下,不同磷浓度对海洋小球藻叶绿素荧光、细胞密度及色素含量影响显著,最大光能转化效率(Fv/Fm)、潜在活性(Fv/Fo)、实际光能转化效率(ΦPSⅡ)和电子传递速率(ETR)均呈先升后降的趋势,3.62 μmol/L处理组显著低于其他各组,434.52 μmol/L处理组一直处在较高水平.说明海洋小球藻的光合作用对高磷的适应范围较广,但对低磷浓度培养反应敏感.非光化学淬灭(qN)的值,3.62 μmol/L处理组高于其他各组.从细胞密度和色素含量的变化可以看出,36.21 μmol/L处理组最高,434.52、3.62 μmol/L处理组均低于36.21 μmol/L处理组.海洋小球藻生长的最适磷摩尔浓度为36.21 μmol/L.     

耐Cd2+假单胞菌富集Cd2+的研究

从安徽某冶炼厂污染土壤中分离出一株能高度耐Cd2+和富集Cd2+的菌株J5.通过光学显微镜、透射电镜、扫描电镜观察到,菌株J5在含2.0 mmol/L Cd2+的液体培养基和75.0 mmol/L Cd2+固体培养基上多以聚集成团块形式逐渐富集CA2+;液体培养基中菌株J5多以四角形的晶体结构存在,而在固体培养基上则以胞外聚集物存在;菌株细胞壁内外密布含Cd2+的颗粒.菌株J5对1.0 mmol/L Cd2+的积累率为99.1%,菌株内Cd2+质量分数可达32%.     

Cu污染土壤接种丛枝菌根真菌对旱稻生长的影响

采用盆栽实验的方法,研究了不同Cu处理水平(0、100和200 mg/kg)下,接种丛枝菌根真菌(arbuscular my-corrhizal fungi,AMF)Glomus mosseae对旱稻(Oryzal Sativa L.)生长的影响。结果表明,未添加Cu处理下,旱稻菌根侵染率可达69%,随着土壤中Cu添加量增加,旱稻菌根侵染率显著下降(P<0.05)。与未接种处理相比,接种处理显著提高100mg/kg Cu处理下根系生物量以及200 mg/kg Cu处理下地上部分生物量(P<0.05);接种处理显著降低了100 mg/kg Cu处理下旱稻地下部Cu含量,却显著增加了200 mg/kg Cu处理下旱稻地上部分以及地下部分Cu含量(P<0.05)。     

Optimization of Height of Release of Air Pollutants

A number of key projects in the Environmental Protection Agency (EPA) particulate R&;D program having applicability to industry are presented. For electrostatic precipitators (ESP) there is presented the result of work on large diameter discharge electrodes which provide a decrease in penetration of up to a factor of 4 when compared to conventional small diameter electrodes. Also discussed is the multistage ESP which provides a collection efficiency that would require a collecting plate area 4 or 5 times larger with conventional ESP technology. The E-SOX technology makes use of the multistage concept to free up space in the ESP for SO₂ removals of up to 90%. Electrostatically augmented fabric filtration provides a reduction in pressure drop of about 5 0% as compared to conventional fabric filtration. Wind tunnel modeling of windbreaks for material storage piles indicates a potential for providing engineering design data that would allow significant emission reduction caused by wind erosion     

Investigation of the characteristics of the reflectivity of clouds

This paper investigates some of the reflectivity characteristics that clouds (when modelled as solid bodies) must exhibit to be compatible with observations that the reflecting surface of a cloud (i) appears almost equally bright across its face, (ii) is brightest when the cloud is opposite to the Sun but decreases in brightness as the cloud moves to other positions and (iii) increases in brightness with increasing optical thickness of the cloud in the observer's line of sight. These observations, respectively, are shown to imply that the peak value of the bidirectional total reflectivity from a cloud surface (i) increases in inverse proportion to the cosine of the angle between the Sun and the normal to the cloud surface, as the incident angle increases, (ii) appears to be directed back in the direction of the incident radiation, and (iii) increases as optical thickness of the cloud in the observer's line of sight increases. The results could have application in many fields (e.g. modelling diffuse radiance distributions for cloudy skies).     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

扬中生态环境建设的思考与实践

结合扬中生态环境的基本情况和存在的不足，进行了具体分析，对扬中未来生态建设的发展方向提出了建议及实施措施。     

实验室质量管理体系内部审核的实施

在实施ISO／IEC17025：1999标准《检测和校准实验室能力的通用要求》过程中，通过实验室质量管理体系内部审核的实践与系统分析，识别出内部审核实施阶段的关键环节，提出召开首次会议、收集审核证据、确定审核发现和召开末次会议的技术方法，对提高内部审核的质量和有效性、获得可靠的审核结论具有重要意义。     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

有机官能团对改性硅吸附微囊藻毒素的影响

考察了不同有机改性硅对微囊藻毒素LR(mLR)和LA(mLA)的等温吸附行为。结果表明,有机改性硅可有效吸附去除水体中<0.1×10-6(质量分数)的微囊藻毒素,并且吸附去除效果随表面改性官能团中碳原子数量的增加而增加;相同条件下,有机改性硅在微囊藻毒素异构体之间存在着一定的吸附选择性。     

生物质快速热裂解主要参数对生物油产率的影响

以松木木屑为原料,在自制的小型流化床上,开展了生物质热裂解温度、生物质粒径和进料速率对生物油产率的影响实验研究.结果表明,在热裂解温度分别为450、475、500、525和550℃条件下,当热裂解温度为500℃时,生物油产率最高,平均产率达到53.33%(质量百分比).反应温度越高,炭产量越低,不可冷凝气体产量越高,气体发热值越高;粒径＜1 mm的生物质其粒径对生物油产率影响不大;生物质进料速率增加时,生物油产率增加.本研究为生物能的利用提供了新的途径.