利用无泵水幕废气净化器治理高浓度NOx的工程实践

介绍了无泵水幕废气净化器的工作原理和运行特点，采用该设备处理某金刚石公司的酸洗车间高浓度的NOx气体，其净化效率达90％以上，净化后的NOx气体可直接达标排放。无泵水幕废气净化器解决了传统的水喷淋塔普遍存在的喷嘴堵塞、单级净化效率低、运行费用高等问题，在高浓度酸性气体治理方面具有很好的推广应用前景。     

生物法净化低浓度工业废气的技术进展

综述了生物法净化有害气体的发展历史与现状，介绍了有机废气、SO2、H2S、NOx废气处理的生物净化实验研究和工业应用情况。     

生物法净化再生胶生产废气工业试验研究

在再生橡胶厂进行橡胶再生低浓度有机废气的生物法净化工业试验研究，对于甲苯浓度为300～1400mg/m^3的再生胶脱硫废气，在常温常压下以气体流量10～20m^3/h、循环液体喷淋量300～500L/h运行生物法废气净化装置获得了良好物净化效果。该装置连续运行100d的结果显示，其对再生胶废气中甲苯的净化效率可较长时间的保持在90%左右，废气经处理后可以实现达标排放，废气处理成本约为工厂再生胶产值的0.12%～0.14%，具有明显的技术先进性和经济合理性。     

中小型工业窑炉NOx废气的净化技术与应用

介绍了中小型工业窑炉生产过程中排放NOx的现状,并针对NOx的治理问题,从工程应用角度,简述了湿法和干法净化NOx的原理和化学反应过程。讨论了NOx排放特性和NOx废气中NO2/NOx比例的问题。提出了影响NOx治理的主要因素,包括吸收剂、吸附剂、催化剂和设备的部分应用参数,并结合工程实例指出工程需要注意的问题。介绍了多项采用湿法和干法净化NOx的工程应用项目,丰富了中小工业窑炉NOx废气的治理的实践经验,为中小工业窑炉排放NOx治理奠定了基础。     

中小型工业窑炉NO_x废气的净化技术与应用

介绍了中小型工业窑炉生产过程中排放NOx的现状,并针对NOx的治理问题,从工程应用角度,简述了湿法和干法净化NOx的原理和化学反应过程。讨论了NOx排放特性和NOx废气中NO2/NOx比例的问题。提出了影响NOx治理的主要因素,包括吸收剂、吸附剂、催化剂和设备的部分应用参数,并结合工程实例指出工程需要注意的问题。介绍了多项采用湿法和干法净化NOx的工程应用项目,丰富了中小工业窑炉NOx废气的治理的实践经验,为中小工业窑炉排放NOx治理奠定了基础。     

生物膜填料塔SO2废气净化性能研究

采用生物膜填料塔净化SO2废气,研究结果表明:当气体流量从100L/h增加到300L/h时,SO2净化效率由86.4%下降到73.2%;生化去除量随着入口SO2气体浓度的升高而增大;随着温度的升高,SO2净化效率和生化去除量都随之提高,且20℃以上时,净化效率可达90.9%以上,生化去除量可达75 mg/L·h以上,更利于微生物降解SO2.     

电弧放电产生NOx及其对亚硫酸铵的氧化

将脱硫塔产生的高浓度亚硫酸铵氧化为硫酸铵是氨法脱硫研究的一个难点。利用二氧化氮(NO2)的氧化性,可以有效氧化高浓度的亚硫酸铵。空气中电弧放电可以产生氮氧化物(NOx),本研究采用高频交流电源,不锈钢针-针电极,研究了放电间距、气体流量、湿度和O2含量等参数对产物NOx的浓度和NO2/NOx比值的影响,并对产物气体做了红外分析和光谱分析。实验结果表明,放电间距增大有利于NOx浓度和NO2/NOx的提高,气体流量和湿度的增大使NOx浓度和NO2/NOx降低,O2含量为50%和60%时NO2浓度和NO2/NOx分别达到最大值。产物NOx对亚硫酸铵的氧化速率最高可达0.0264 mol/(L·min)。     

生物膜填料塔净化低浓度苯乙烯废气的实验研究

研究了进口气体中苯乙烯浓度、气体流量和液体流量等3个因素对生物膜填料塔净化苯乙烯废气的影响.研究结果表明,当进口气体中苯乙烯浓度为1000 mg/m3以下、气体流量为200L/h、循环液流量为10L/h的操作条件下,废气中苯乙烯的去除率可达90%以上.     

好氧反硝化去除低浓度NOx的动力学模型研究

在好氧条件下,对利用生物滴滤塔(bio-tricklingfilter,BTF)反硝化净化废气中NOx的过程进行了理论模型探讨,并用实验结果进行了验证.在分析NOx在BTF内传质以及生物降解过程的基础上,建立了NOx在气相和生物膜相的质量守恒方程,结合Fick定律和好氧条件下的Monod微生物反应动力学方程,最终得到了...     

旋流式饮食业厨房油烟净化器的实验研究

研究了一种湿法油烟净化器 ,该净化器对饮食业油烟气中的油雾和异味均有良好的净化效果 ,着重探讨了两种净化效率与风速、压力降、润湿剂的关系 ,得出最佳操作条件。     

The importance of the location of sodium chlorite application in a multipollutant flue gas cleaning system

In this study, removing sulfur dioxide (SO2), nitrogen oxides (NO(x)), and mercury (Hg) from simulated flue gas was investigated in two laboratory-sized bubbling reactors that simulated an oxidizing reactor (where the NO and Hg(0) oxidation reactions are expected to occur) and a wet limestone scrubber, respectively. A sodium chlorite solution was used as the oxidizing agent. The sodium chlorite solution was an effective additive that enhanced the NO(x), Hg, and SO2 capture from the flue gas. Furthermore, it was discovered that the location of the sodium chlorite application (before, in, or after the wet scrubber) greatly influences which pollutants are removed and the amount removed. This effect is related to the chemical conditions (pH, absence/presence of particular gases) that are present at different positions throughout the flue gas cleaning system profile. The research results indicated that there is a potential to achieve nearly zero SO2, NO(x), and Hg emissions (complete SO2, NO, and Hg removals and -90% of NO(x) absorption from initial values of 1500 ppmv of SO2, 200 ppmv of NO(x), and 206 microg/m3 of Hg(0)) from the flue gas when sodium chlorite was applied before the wet limestone scrubber. However applying the oxidizer after the wet limestone scrubber was the most effective configuration for Hg and NO(x) control for extremely low chlorite concentrations (below 0.002 M) and therefore appears to be the best configuration for Hg control or as an additional step in NO(x) recleaning (after other NO(x) control facilities). The multipollutant scrubber, into which the chlorite was injected simultaneously with the calcium carbonate slurry, appeared to be the least expensive solution (when consider only capital cost), but exhibited the lowest NO(x) absorption at -50%. The bench-scale test results presented can be used to develop performance predictions for a full- or pilot-scale multipollutant flue gas cleaning system equipped with wet flue gas desulfurization scrubber.     

Effect of solution pH on SO2, NO(x), and Hg removal from simulated coal combustion flue gas in an oxidant-enhanced wet scrubber

This paper presents a study on the simultaneous removal of SO2, NO(x) and Hg (both Hg0 and Hg2+) from a simulated flue gas by oxidant injection in a bench-simulated wet limestone scrubber for a wide range of slurry pH. The slurry pH strongly influenced the chemical mechanism in the scrubber and, therefore, affected pollutant removal. This paper also examines the potential ClO2(gas) reemission from a developed multipollutant scrubber at different slurry pHs. To better understand the chemical mechanisms at each slurry pH and to apply a mass balance to the process, detailed product ion analyses were performed for all experiments. Ion analysis covered three different chlorine species (chlorite, chloride, chlorate), sulfate, nitrite and nitrate. Different NO(x) removal efficiencies and mechanisms were found in acidic and alkaline pHs in the multipollutant scrubber. The acidic solution was favorable for NO and Hg0 oxidation, but increasing the slurry pH above 7.0 was disadvantageous for NO and Hg oxidation/removal. However the rate of NO(x) absorption (by percentage) was higher for the alkaline solution.     

The utilization of catalyst sorbent in scrubbing acid gases from incineration flue gas

Catalyst sorbents based on alumina-supported CuO, CeO2, and CuO-CeO2 were applied to a dry scrubber to clean up the SO2/HCl/NO simultaneously from pilot-scale fluidized-bed incineration flue gas. In the presence of organic compounds, CO and the submicron particles SO2 and HCI removed by the fresh catalyst sorbents and NO reduced to N2 by NH3 under the catalysis of fresh and spent desulfurization/dechloridization (DeSO2/DeHCl) catalyst sorbents (copper compounds, Cu, CuO, and CuSO4) were evaluated in this paper. The fresh and spent catalyst sorbents were characterized by the Brunner-Emmett-Teller method (BET), X-ray powder diffraction (XRPD), scanning electron microscopy (SEM), inductively coupled plasma-mass spectrometry (ICP-MS), and the elemental analyzer (EA). The study showed that the performances of CuO, CeO2, and CuO-CeO2/gamma-Al2O3 were better than that of Ca(OH)2. The removal efficiency of SO2 and HCl was 80-95% in the dry scrubber system. Under NH3/NO = 1, NO could not be reduced to N2 because it was difficult to control the ratio of air/fuel in the flue gas. For estimating the feasibility of regenerating the spent catalyst sorbents, BET and EA analyses were used. They indicated that the pore structures were nearly maintained and a small amount of carbon accumulated on their surface.     

电子束半干法烟气净化技术

电子束烟气净化技术由于能够同时脱除烟气中的SO2 和NOx 而得到世界各国环保界的重视。传统的电子束烟气净化技术在工业应用中存在能耗高、副产品黏结严重、工作可靠性低等问题。新型电子束半干法烟气净化技术解决了传统工艺在工业化应用中存在的问题 ,可以在较小的辐照剂量下获得更为理想的烟气净化效果 ,提高了系统的工作可靠性 ,是一项工业应用前景十分广阔的环保技术。     

隔膜电解海水氧化耦合吸收脱硫脱硝净化船舶尾气技术

采用隔膜电解技术对海水进行改性,生成的氧化液和碱性液分别喷淋进入氧化洗涤塔和碱式吸收塔,通过耦合的二段式反应研究脱除模拟船舶尾气中NO与SO2的性能,实验详细考察了NO与SO2的气体流量与初始浓度、海水电解时间和氧化液有效氯浓度对SO2和NO脱除效率的影响。结果表明:隔膜电解海水能够高效地脱除船舶尾气中的SO2和NO;SO2脱除效率高,在实验条件范围内几乎不受各因素的影响;NO脱除效率随NO初始浓度、海水电解时间、氧化液有效氯浓度的提升而增大,随SO2初始浓度、气体流量的提升而减小。当气体流量为1 m3·h-1,初始SO2、NO浓度分别为600 mL·m-3和900 mL·m-3,海水电解时间为60 min,氧化液有效氯浓度为540 mg·L-1时,模拟船舶尾气中SO2和NO的去除效率可以分别达到98.6%和84.4%。     

燃煤锅炉烟气NOx污染等离子体治理技术

燃煤锅炉烟气NOx污染治理技术种类较多.本文综合评述了各种烟气NOx污染等离子体治理技术,重点介绍了电晕放电脱除烟气中NOx的最新研究成果.对燃煤锅炉烟气NOx污染治理技术的研究和开发具有实用价值.     

An efficient venturi scrubber system to remove submicron particles in exhaust gas

An efficient venturi scrubber system making use of heterogeneous nucleation and condensational growth of particles was designed and tested to remove fine particles from the exhaust of a local scrubber where residual SiH4 gas was abated and lots of fine SiO2 particles were generated. In front of the venturi scrubber, normal-temperature fine-water mist mixes with high-temperature exhaust gas to cool it to the saturation temperature, allowing submicron particles to grow into micron sizes. The grown particles are then scrubbed efficiently in the venturi scrubber. Test results show that the present venturi scrubber system is effective for removing submicron particles. For SiO2 particles greater than 0.1microm, the removal efficiency is greater than 80-90%, depending on particle concentration. The corresponding pressure drop is relatively low. For example, the pressure drop of the venturi scrubber is approximately 15.4 +/- 2.4 cm H2O when the liquid-to-gas ratio is 1.50 L/m3. A theoretical calculation has been conducted to simulate particle growth process and the removal efficiency of the venturi scrubber. The theoretical results agree with the experimental data reasonably well when SiO2 particle diameter is greater than 0.1 microm.     

锅炉烟气联合脱硫脱氮技术

硫氧化物和氮氧化物是燃煤锅炉排放的主要污染物 ,传统分步脱硫脱氮设备昂贵且效率不高 ,而联合脱硫脱氮技术具有很大的优越性 ,如可以减小系统的复杂性、具有更好的运行性能、较低的成本及较小的占地面积 ,因此实现在一个系统内同时脱硫脱氮的工艺成为国内外烟气净化技术的研究重点。对近年来国内外各种联合脱硫脱氮技术的脱除原理、研究现状、应用情况和主要优缺点进行了论述 ,并对各工艺的经济技术指标给予了多方面的比较。通过对两类烟气联合脱硫脱氮技术 (炉内联合脱除和烟气中联合脱除 )的分析、综合和比较 ,找出了我国今后脱硫脱氮技术的研究重点 ,从而为脱硫脱氮技术的进一步开发和改进提供参考     

Evaluation of NO(x) flue gas analyzers for accuracy and their applicability for low-concentration measurements

The requirements of the Texas State Implementation Plan of the U.S. Clean Air Act for the Houston-Galveston Ozone Nonattainment Area stipulate large reductions in oxides of nitrogen (NO(x)) emissions. A large number of sources at Dow Chemical Co. sites within the nonattainment area may require the addition of continuous emission monitoring systems (CEMS) for online analysis of NO(x), CO, and O2. At the outset of this work, it was not known whether the analyzers could accurately measure NO(x) as low as 2 ppm. Therefore, NO(x) CEMS analyzers from five different companies were evaluated for their ability to reliably measure NO(x) in the 2-20 ppm range. Testing was performed with a laboratory apparatus that accurately simulated different mixtures of flue gas and, on a limited basis, simulated a dual-train sampling system on a gas turbine. The results indicate that this method is a reasonable approach for analyzer testing and reveal important technical performance aspects for accurate NO(x) measurements. Several commercial analyzers, if installed in a CEMS application with sampling conditioning components similar to those used in this study, can meet the U.S. Environmental Protection Agency's measurement data quality requirements for accuracy.     

Responses of spruce seedlings (Picea abies) to exhaust gas under laboratory conditions--I. Plant-insect interactions

The effects of motor vehicle exhaust gas on Norway spruce seedlings (Picea abies (L.) Karst) and plant-insect interaction of spruce shoot aphid (Cinara pilicornis Hartig) was studied. The exhaust gas concentrations in the fumigation chambers were monitored and controlled by measuring the concentration of nitrogen oxides (NO(x)) with a computer aided feedback system. The concentrations of major exhaust gas components (black carbon [BC], fine particles, VOCs and carbonyl compounds) in the chamber air were also measured. Responses of Norway spruce seedlings to a 2 and 3-week exhaust gas exposure and subsequent performance of spruce shoot aphid were studied using realistic exposure regimes; 50, 100 and 200 ppb NO(x). The feedback control system based on NO(x) concentrations proved an adequate and practical means for controlling the concentration of exhaust gases and studying plant responses in controlled environment chambers. The exhaust exposure resulted in increased concentrations of proline, glutamine, threonine, aspartic acid, glycine and phenylalanine and decreased concentration of arginine, serine, alanine and glycine in young needles. No changes in soluble N concentrations were observed. The results are interpreted as a stress response rather than use of NO(x) as a nitrogen source. No changes in total phenolics and only transient changes in some individual terpene concentrations were detected. The exhaust gas exposure stressed the exposed seedlings, but had no significant effect on N metabolism or the production of defence chemicals. Aphid performance was not significantly affected. Soluble N, secondary metabolism and aphid performance were not sensitive to exhaust gas exposure during shoot elongation in Norway spruce.