共查询到19条相似文献,搜索用时 375 毫秒
1.
2.
在传统的钢棒弯圆工艺中,大多采用橡皮弯曲模、斜楔模、铰链模、手工夹具、专机专用模等方法.但以上方法来弯圆或多或少受到资金,成形要求,班产量的限制.针对这一问题,本人设计了一种新颖高效率的钢棒弯圆模,它通过凸模与凹模迫使钢棒滑入凹模孔内,并进行弯曲,最后成形.班产量可达16800只,此模具具有制造、维修容易、成本低、工艺性能可靠、寿命长等特点.各种钢棒弯圆模比较见下表. 相似文献
3.
孔对称布置的弯曲成形零件,在孔尺寸及形位精度要求较高的情况下,通常有一定的加工难度,此文介绍了斜楔式双向冲孔模成功的用于孔对称布置弯曲成形零件的加工方法及模具. 相似文献
4.
1 斜楔式冲模设计 1.4 斜楔滑板的表面压力与行程的求法从楔块上传来的力(P)和作用于楔形滑板运动方向所需要的加工力(F),与楔形滑板行程(S)以及作用于楔块表面的表 相似文献
5.
6.
根据制件的特点 ,分析了其冲压成形的工艺难点 ,制定了合理的工艺 ,简化了模具设计和制造 ,并画出了制件的综合工序图 ,分析了各工序内容和工艺特点 ,说明了各工序模具设计的关键问题。同时以第 5道工序为例 ,重点分析了斜楔翻边、翻边模的结构、工作原理及设计要点 相似文献
7.
讨论多向模锻的模具结构水平分模模具结构、垂直分模模具结构、联合分模模具结构和特殊模具结构,在此基础上,又讨论多向模锻模具的型腔位置、导向装置、凹模导向、深孔锻件凹模、冲头、推杆等设计的要点以及模具材料的选用. 相似文献
9.
讨论了精密模锻件的分类密集形状的锻件、盘形锻件和长杆形锻件 ,以及精密模锻件的设计要点精密模锻件的机械加工余量、尺寸精度和表面粗糙度、分模面的选择、模锻斜度、圆角半径、肋的设计和腹板厚度的设计 相似文献
10.
众所周知,在设计冲裁模时,为了使冲裁件或废料不卡在凹模里,通常将凹模设计成一个出料斜度、或较短的刃口。但凸模因不受这一约束而刃口都较长。这样在相同的磨损条件下,凹模可修次数没有凸模多。往往凹模巳修磨超差,而凸模仍可继续使用。如果用某一工艺消隐凹模这些增大了的间隙,就可使凹模恢复原有的精度,冲出合格的产品。我们在超差了的凹模上方利用导料板 相似文献
11.
12.
此文分析在二辊楔横轧中轧制各类轴肩的过程。在假想工件轴端固定的图上确定楔侧面截面轮廓形状,再通过叠加轴向刚性移动量确定各截面实际位置,比较直观简便地设计出轧制轴肩的辊面上的成形曲面。最后归纳了设计步骤。 相似文献
13.
14.
根据楔横轧模具孔型及其加工成形的特点,对楔横轧模具大面积大螺距楔形提出了一种简单高效的铣削加工方法,并设计制造了楔横轧轧辊模具孔型加工专用机床——SDM机床。新设计的SDM机床投资小,可以加工直径为φ620 mm~φ1000mm的轧辊模具,加工导程最大可达469 mm,加工周期短,成本低,且大大降低了工人劳动强度。 相似文献
15.
The Basque country magnetic anomaly follows a NW-SE trend over the Basque country (northern Spain) with intensities up to
250 nT measured at 3000 m above sea level. The paired negative part of the anomaly is located to the north and presents intensities
down to −60 nT. A model of the magnetic properties of the crust in the area, taking into account previous geological and geophysical
data, indicates a wedge of material with a magnetic susceptibility of 0.07 SI emplaced along a NE-directed basal thrust. The
anomalous wedge is composed of basic and/or ultrabasic Cretaceous intrusives and lower crustal rocks, and reaches a minimum
depth which increases towards the northwest from 5–7 to 12 km. According to previous works, geological features of the rocks
on top of the anomalous wedge indicate that during the Cretaceous this zone constituted a deep marine environment which underwent
important crustal thinning related to rifting. The transition towards the southwest was to a normal continental platform.
Alpine deformation gave rise to displacement on a basal thrust, which can be correlated with the lower contact of the magnetic
wedge, and emplacement of this wedge towards the northeast. The southeastern termination of the anomaly can be related to
the lateral termination of the basic rocks which constitute the anomalous wedge in a transform fault related to the rifting
event. 相似文献
16.
17.
通过使用可移式轧辊模具 ,成功地利用一副模具轧制出了形状相似、仅局部尺寸不同的多种规格的阶梯轴 ,使楔横轧工艺在规格较多、批量较小的轴类零件毛坯成形中得到了应用 ,楔横轧技术得到了进一步发展和推广。 相似文献
18.
19.
挡土墙后粘性填土被动土压力计算 总被引:1,自引:0,他引:1
根据库伦土压力的计算原理,从滑动土楔处于极限平衡状态时力的静力平衡条件出发,推导出了计算粘性土或无粘性土被动土压力的公式.该公式适用于均布荷载作用于挡土墙后任意位置.对重力式挡土墙设计中土压力的计算具有一定参考价值. 相似文献